OpenCores
URL https://opencores.org/ocsvn/forwardcom/forwardcom/trunk

Subversion Repositories forwardcom

[/] [forwardcom/] [trunk/] [config_r32F675.vh] - Blame information for rev 16

Details | Compare with Previous | View Log

Line No. Rev Author Line
1 16 Agner
//////////////////////////////////////////////////////////////////////////////////
2
// Engineer:       Agner Fog
3
// 
4
// Create Date:    2020-06-06
5
// Last modified:  2021-08-07
6
// Module Name:    config_r32.vh
7
// Project Name:   ForwardCom soft core model A
8
// Target Devices: Artix 7
9
// Tool Versions:  Vivado v. 2020.1
10
// License:        CERN-OHL-W v. 2 or later
11
// Description:    Configuration parameters 
12
//
13
// Configuration for 32 bit registers, 32kB data RAM, 64 kB code RAM
14
//
15
//////////////////////////////////////////////////////////////////////////////////
16
 
17
`define NUM_VECTOR_UNITS       0       // number of 64-bit vector units or lanes
18
 
19
// Decide if we have 64 bits support. We can use less resources and have higher speed with the 32 bit version. 
20
// If 32 bits: General purpose registers are 32 bits. Temporary operand buffers are 32 bits.
21
// Result buses are 32 bits. Results will be 32 bits, even for 64 bit instructions. 
22
// The data write buses to data cache and code cache are still 64 bits, using any part of the bus for smaller operand sizes.
23
// If 64 bits: General purpose registers are 64 bits. 64 bit operand size is supported.
24
 
25
// Uncomment this to support 64-bit operand type:
26
//`define SUPPORT_64BIT
27
 
28
`ifdef SUPPORT_64BIT
29
    `define RB                    64   // size of general purpose registers, 64 bits
30
    `define RB1                   63   // index of most significant bit
31
`else
32
    `define RB                    32   // size of general purpose registers, 32 bits
33
    `define RB1                   31   // index of most significant bit
34
`endif
35
 
36
// number of bits used in mask registers must be TAG_WIDTH < MASKSZ <= RB
37
`define MASKSZ                  18
38
//`define MASKSZ                    32
39
//`define MASKSZ                 `RB
40
 
41
 
42
// Clock frequency
43
// Xilinx-specific:
44
// To change the clock frequency, click on the clock_generator source to open the
45
// Vivado Clocking Wizard and set the requested output frequency.
46
// Use the timing summary to check if the design can work with this frequency.
47
// The frequency defined below must match the frequency set in the clocking wizard: 
48
`define CLOCK_FREQUENCY   67500000     // max clock frequency for 32-bit version
49
//`define CLOCK_FREQUENCY   58000000   // max clock frequency for 64-bit version
50
 
51
 
52
// Serial input/output BUAD rate. 8 data bits, no parity, 1 stop bit 
53
//`define BAUD_RATE      19200
54
`define BAUD_RATE        57600
55
//`define BAUD_RATE      115200
56
 
57
// serial input  buffer size is 2**IN_BUFFER_SIZE_LOG2 bytes
58
// serial output buffer size is 2**OUT_BUFFER_SIZE_LOG2 bytes
59
`define IN_BUFFER_SIZE_LOG2    10      // 1 kbyte
60
`define OUT_BUFFER_SIZE_LOG2   11      // 2 kbytes
61
 
62
// initial code in 64-bit lines. remember to put the second 32-bit word to the left:
63
`define LOADER_FILE "loader.mem"       // filename of hex file of machine code for loader
64
`define MAX_LOADER_SIZE 32'H200        // >= size of loader code, in 32-bit words. Must be even
65
// Loader entry address is the end of code memory - MAX_LOADER_SIZE
66
// Restart address is the same address + 1
67
 
68
// code ram address lines. Each line has one 32-bit word = 4 bytes
69
// code ram size = 2**(CODE_ADDR_WIDTH+2)
70
//`define CODE_ADDR_WIDTH 13  // 32 kB
71
`define CODE_ADDR_WIDTH 14  // 64 kB
72
//`define CODE_ADDR_WIDTH 15  // 128 kB
73
 
74
// data ram address lines. Each line has 1 byte. 
75
// data ram size = (2**DATA_ADDR_WIDTH)
76
`define DATA_ADDR_WIDTH 15   // 32 kB
77
 
78
// total address lines for code and data combined, used when writing code. 
79
// Total address space = (2**COMMON_ADDR_WIDTH) bytes
80
`define COMMON_ADDR_WIDTH ((`CODE_ADDR_WIDTH+2>`DATA_ADDR_WIDTH) ? `CODE_ADDR_WIDTH+3 : `DATA_ADDR_WIDTH+1)
81
 
82
// The code address space must start immediately after the data address space if IP-addressed data are used without load-time relocation:  
83
`define CODE_ADDR_START `DATA_ADDR_WIDTH   // code write address starts at 2**`CODE_ADDR_START = end of data address space
84
 
85
// code ram bus width
86
`define CODE_DATA_WIDTH 64
87
 
88
// The number of entries in the call stack size is 2**CALL_STACK_POINTER_BITS - 1
89
`define CALL_STACK_POINTER_BITS  10
90
 
91
// number of system registers that behave as g.p. registers (renamed in flight)
92
`define NUM_SYS_REGISTERS    3
93
 
94
// number of bits in instruction ID tag. 
95
// The maximum number of instruction tags in flight is 2**TAG_WIDTH - 1  
96
`define TAG_WIDTH  5
97
 
98
// number of error types distinguished
99
`define N_ERROR_TYPES  6
100
 
101
// Input/output port numbers
102
`define INPORT_RS232            8      // input port for RS232 serial input
103
`define INPORT_RS232_STATUS     9      // input port to read status of RS232 serial input
104
`define OUTPORT_RS232          10      // output port for RS232 serial output
105
`define OUTPORT_RS232_STATUS   11      // output port for RS232 serial output status
106
 

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.