Subversion Repositories udp_ip_stack

----------------------------------------------------------------------------------

-- Company: 

-- Engineer:            Peter Fall

-- 

-- Create Date:    5 June 2011 

-- Design Name: 

-- Module Name:    UDP_TX - Behavioral 

-- Project Name: 

-- Target Devices: 

-- Tool versions: 

-- Description: 

--              handle simple UDP TX

--              doesnt generate the checksum(supposedly optional)

-- Dependencies: 

--

-- Revision: 

-- Revision 0.01 - File Created

-- Additional Comments: 

--

----------------------------------------------------------------------------------

library IEEE;

use IEEE.STD_LOGIC_1164.ALL;

use IEEE.NUMERIC_STD.ALL;

use work.axi.all;

use work.ipv4_types.all;

entity UDP_TX is

    Port (

                        -- UDP Layer signals

                        udp_tx_start                    : in std_logic;                                                 -- indicates req to tx UDP

                        udp_txi                                 : in udp_tx_type;                                                       -- UDP tx cxns

                        udp_tx_result                   : out std_logic_vector (1 downto 0);-- tx status (changes during transmission)

                        udp_tx_data_out_ready: out std_logic;                                                   -- indicates udp_tx is ready to take data

                        -- system signals

                        clk                                             : in  STD_LOGIC;                                                        -- same clock used to clock mac data and ip data

                        reset                                   : in  STD_LOGIC;

                        -- IP layer TX signals

                        ip_tx_start                             : out std_logic;

                        ip_tx                                           : out ipv4_tx_type;                                                     -- IP tx cxns

                        ip_tx_result                    : in std_logic_vector (1 downto 0);              -- tx status (changes during transmission)

                        ip_tx_data_out_ready    : in std_logic                                                                  -- indicates IP TX is ready to take data

                        );

end UDP_TX;

architecture Behavioral of UDP_TX is

        type tx_state_type is (IDLE,    SEND_UDP_HDR, SEND_USER_DATA);

        type count_mode_type is (RST, INCR, HOLD);

        type settable_cnt_type is (RST, SET, INCR, HOLD);

        type set_clr_type is (SET, CLR, HOLD);

        -- TX state variables

        signal udp_tx_state             : tx_state_type;

        signal tx_count                         : unsigned (15 downto 0);

        signal tx_result_reg            : std_logic_vector (1 downto 0);

        signal ip_tx_start_reg  : std_logic;

        signal data_out_ready_reg       : std_logic;

        -- tx control signals

        signal next_tx_state    : tx_state_type;

        signal set_tx_state             : std_logic;

        signal next_tx_result   : std_logic_vector (1 downto 0);

        signal set_tx_result            : std_logic;

        signal tx_count_val             : unsigned (15 downto 0);

        signal tx_count_mode            : settable_cnt_type;

        signal tx_data                          : std_logic_vector (7 downto 0);

        signal set_last                 : std_logic;

        signal set_ip_tx_start  : set_clr_type;

        signal tx_data_valid            : std_logic;                    -- indicates whether data is valid to tx or not

        -- tx temp signals

        signal total_length             : std_logic_vector (15 downto 0);        -- computed combinatorially from header size

-- IP datagram header format

--

--      0          4          8                      16      19             24                    31

--      --------------------------------------------------------------------------------------------

--      |              source port number            |              dest port number               |

--      |                                            |                                             |

--      --------------------------------------------------------------------------------------------

--      |                length (bytes)              |                checksum                     |

--      |          (header and data combined)        |                                             |

--      --------------------------------------------------------------------------------------------

--      |                                          Data                                            |

--      |                                                                                          |

--      --------------------------------------------------------------------------------------------

--      |                                          ....                                            |

--      |                                                                                          |

--      --------------------------------------------------------------------------------------------

begin

        -----------------------------------------------------------------------

        -- combinatorial process to implement FSM and determine control signals

        -----------------------------------------------------------------------

        tx_combinatorial : process(

                -- input signals

                udp_tx_start, udp_txi, clk, ip_tx_result, ip_tx_data_out_ready,

                -- state variables

                udp_tx_state, tx_count, tx_result_reg, ip_tx_start_reg, data_out_ready_reg,

                -- control signals

                next_tx_state, set_tx_state, next_tx_result, set_tx_result, tx_count_mode, tx_count_val,

                tx_data, set_last, total_length, set_ip_tx_start, tx_data_valid

                )

        begin

                -- set output followers

                ip_tx_start <= ip_tx_start_reg;

                ip_tx.hdr.protocol <= x"11";    -- UDP protocol

                ip_tx.hdr.data_length <= total_length;

                ip_tx.hdr.dst_ip_addr <= udp_txi.hdr.dst_ip_addr;

                udp_tx_result <= tx_result_reg;

                case udp_tx_state is

                        when SEND_USER_DATA =>

                                ip_tx.data.data_out <= udp_txi.data.data_out;

                                tx_data_valid <= udp_txi.data.data_out_valid;

                                ip_tx.data.data_out_last <= udp_txi.data.data_out_last;

                        when SEND_UDP_HDR =>

                                ip_tx.data.data_out <= tx_data;

                                tx_data_valid <= ip_tx_data_out_ready;

                                ip_tx.data.data_out_last <= set_last;

                        when others =>

                                ip_tx.data.data_out <= (others => '0');

                                tx_data_valid <= '0';

                                ip_tx.data.data_out_last <= set_last;

                end case;

                ip_tx.data.data_out_valid <= tx_data_valid and ip_tx_data_out_ready;

                -- set signal defaults

                next_tx_state <= IDLE;

                set_tx_state <= '0';

                tx_count_mode <= HOLD;

                tx_data <= x"00";

                set_last <= '0';

                next_tx_result <= UDPTX_RESULT_NONE;

                set_tx_result <= '0';

                set_ip_tx_start <= HOLD;

                tx_count_val <= (others => '0');

                -- set temp signals

                total_length <= std_logic_vector(unsigned(udp_txi.hdr.data_length) + 8);                -- total length = user data length + header length (bytes)

                -- TX FSM

                case udp_tx_state is

                        when IDLE =>

                                udp_tx_data_out_ready <= '0';            -- in this state, we are unable to accept user data for tx

                                tx_count_mode <= RST;

                                if udp_tx_start = '1' then

                                        -- check header count for error if too high

                                        if unsigned(udp_txi.hdr.data_length) > 1472 then

                                                next_tx_result <= UDPTX_RESULT_ERR;

                                                set_tx_result <= '1';

                                        else

                                                -- start to send UDP header

                                                tx_count_mode <= RST;

                                                next_tx_result <= UDPTX_RESULT_SENDING;

                                                set_ip_tx_start <= SET;

                                                set_tx_result <= '1';

                                                next_tx_state <= SEND_UDP_HDR;

                                                set_tx_state <= '1';

                                        end if;

                                end if;

                        when SEND_UDP_HDR =>

                                udp_tx_data_out_ready <= '0';            -- in this state, we are unable to accept user data for tx

                                if ip_tx_data_out_ready = '1' then

                                        if tx_count = x"0007" then

                                                tx_count_val <= x"0001";

                                                tx_count_mode <= SET;

                                                next_tx_state <= SEND_USER_DATA;

                                                set_tx_state <= '1';

                                        else

                                                tx_count_mode <= INCR;

                                        end if;

                                        case tx_count is

                                                when x"0000"  => tx_data <= udp_txi.hdr.src_port (15 downto 8); -- src port

                                                when x"0001"  => tx_data <= udp_txi.hdr.src_port (7 downto 0);

                                                when x"0002"  => tx_data <= udp_txi.hdr.dst_port (15 downto 8); -- dst port

                                                when x"0003"  => tx_data <= udp_txi.hdr.dst_port (7 downto 0);

                                                when x"0004"  => tx_data <= total_length (15 downto 8);                         -- length

                                                when x"0005"  => tx_data <= total_length (7 downto 0);

                                                when x"0006"  => tx_data <= udp_txi.hdr.checksum (15 downto 8); -- checksum (set by upstream)

                                                when x"0007"  => tx_data <= udp_txi.hdr.checksum (7 downto 0);

                                                when others =>

                                                        -- shouldnt get here - handle as error

                                                        next_tx_result <= IPTX_RESULT_ERR;

                                                        set_tx_result <= '1';

                                        end case;

                                end if;

                        when SEND_USER_DATA =>

                                udp_tx_data_out_ready <= '1';           -- in this state, we are always ready to accept user data for tx

                                if ip_tx_data_out_ready = '1' then

                                        if udp_txi.data.data_out_valid = '1' or tx_count = x"000" then

                                                -- only increment if ready and valid has been subsequently established, otherwise data count moves on too fast

                                                if unsigned(tx_count) = unsigned(udp_txi.hdr.data_length) then

                                                        set_last <= '1';

                                                        tx_data <= udp_txi.data.data_out;

                                                        next_tx_result <= UDPTX_RESULT_SENT;

                                                        set_ip_tx_start <= CLR;

                                                        set_tx_result <= '1';

                                                        next_tx_state <= IDLE;

                                                        set_tx_state <= '1';

                                                else

                                                        tx_count_mode <= INCR;

                                                        tx_data <= udp_txi.data.data_out;

                                                end if;

                                        end if;

                                end if;

                end case;

        end process;

        -----------------------------------------------------------------------------

        -- sequential process to action control signals and change states and outputs

        -----------------------------------------------------------------------------

        tx_sequential : process (clk,reset,data_out_ready_reg)

        begin

                if rising_edge(clk) then

                        data_out_ready_reg <= ip_tx_data_out_ready;

                else

                        data_out_ready_reg <= data_out_ready_reg;

                end if;

                if rising_edge(clk) then

                        if reset = '1' then

                                -- reset state variables

                                udp_tx_state <= IDLE;

                                tx_count <= x"0000";

                                tx_result_reg <= IPTX_RESULT_NONE;

                                ip_tx_start_reg <= '0';

                        else

                                -- Next udp_tx_state processing

                                if set_tx_state = '1' then

                                        udp_tx_state <= next_tx_state;

                                else

                                        udp_tx_state <= udp_tx_state;

                                end if;

                                -- ip_tx_start_reg processing

                                case set_ip_tx_start is

                                        when SET  => ip_tx_start_reg <= '1';

                                        when CLR  => ip_tx_start_reg <= '0';

                                        when HOLD => ip_tx_start_reg <= ip_tx_start_reg;

                                end case;

                                -- tx result processing

                                if set_tx_result = '1' then

                                        tx_result_reg <= next_tx_result;

                                else

                                        tx_result_reg <= tx_result_reg;

                                end if;

                                -- tx_count processing

                                case tx_count_mode is

                                        when RST  =>    tx_count <= x"0000";

                                        when SET  =>    tx_count <= tx_count_val;

                                        when INCR =>    tx_count <= tx_count + 1;

                                        when HOLD =>    tx_count <= tx_count;

                                end case;

                        end if;

                end if;

        end process;

end Behavioral;