OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

Compare Revisions

  • This comparison shows the changes necessary to convert path
    /
    from Rev 137 to Rev 136
    Reverse comparison

Rev 137 → Rev 136

/minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/minsoc_bench_defines.v
0,0 → 1,29
//set RTL for simulation, override FPGA specific definitions (JTAG TAP, MEMORY and CLOCK DIVIDER)
`define GENERIC_FPGA
`define MEMORY_MODEL //simulation uses a memory model enabling INITIALIZE_MEMORY_MODEL. If you comment this, START_UP might be interesting.
`define NO_CLOCK_DIVISION //if commented out, generic clock division is implemented (odd divisors are rounded down)
//~set RTL for simulation, override FPGA specific definitions (JTAG TAP, MEMORY and CLOCK DIVIDER)
 
`define FREQ_NUM_FOR_NS 100000000
 
`define FREQ 10000000
`define CLK_PERIOD (`FREQ_NUM_FOR_NS/`FREQ)
 
`define ETH_PHY_FREQ 25000000
`define ETH_PHY_PERIOD (`FREQ_NUM_FOR_NS/`ETH_PHY_FREQ) //40ns
 
`define UART_BAUDRATE 115200
 
`define VPI_DEBUG
 
//`define VCD_OUTPUT
 
//`define START_UP //pass firmware over spi to or1k_startup
 
`define INITIALIZE_MEMORY_MODEL //instantaneously initialize memory model with firmware
//only use with the memory model.
//If you use the original memory (`define MEMORY_MODEL
//commented out), comment this too.
 
`define TEST_UART
//`define TEST_ETHERNET
minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/minsoc_bench_defines.v Property changes : Added: svn:executable ## -0,0 +1 ## +* \ No newline at end of property Index: minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/configure =================================================================== --- minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/configure (nonexistent) +++ minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/configure (revision 136) @@ -0,0 +1,121 @@ +#!/bin/bash + +#NON STANDARD SCRIPT, USE ANOTHER AS TEMPLATE, NON STANDARD PART IS MARKED AS COMMENT + +#new boards have to udpate this +BOARD=spartan3e_starter_kit_eth #this has to have the name of the directory this file is in +DEVICE_PART='xc3s500e-4-fg320' +CONSTRAINT_FILE='spartan3e_starter_kit_eth.ucf' +#~new boards update + +#system workings +MINSOC_DIR=`pwd`/../.. +BACKEND_DIR=$MINSOC_DIR/backend +SYN_DIR=$MINSOC_DIR/syn +SYNSRC_DIR=$MINSOC_DIR/prj/xilinx +SYNSUPPORT_DIR=$SYN_DIR/buildSupport +MAKEFILE_DIR=$SYN_DIR/xilinx + +SYN_FILES=(ethmac.xst uart_top.xst adbg_top.xst or1200_top.xst minsoc_top.xst) +MAKEFILE=Makefile + +FIND_PART='DEVICE_PART' +FIND_CONSTRAINT='CONSTRAINT_FILE' + +BOARD_DIR=$BACKEND_DIR/$BOARD +BOARD_FILES=(board.h orp.ld minsoc_defines.v minsoc_bench_defines.v gcc-opt.mk $CONSTRAINT_FILE) + +in_minsoc=`pwd | grep minsoc/backend/${BOARD}$` +if [ -z $in_minsoc ] +then + echo "" + echo " !!!WARNING!!!" + echo "This script cannot be run if not in a board directory inside minsoc/backend," + echo "because it relies on the directory structure of the minsoc system." + echo "" + echo "Possibly your minsoc directory is named differently, minsoc_trunk for example." + echo "Its name must be minsoc only." + echo "" + exit 1 +fi + +#NON STANDARD SCRIPT PART +echo "THIS SCRIPT HAS A NON-STANDARD BEGINNING." +echo "__________________________________________________________________________" +echo "${BOARD} requires another configuration for or1200_rel1." + +echo "" +echo "Copying or1200_defines.v, to or1200 implementation directory..." +echo "(minsoc/rtl/verilog/or1200/rtl/verilog)" +echo "__________________________________________________________________________" +cp $BOARD_DIR/or1200_defines.v $MINSOC_DIR/rtl/verilog/or1200/rtl/verilog +echo "" +echo "REGULAR SCRIPT STARTS NOW" +echo "__________________________________________________________________________" +#~NON STANDARD SCRIPT PART + +echo "" +echo "This script sets up the SoC for simulations and synthesis." +echo "" +echo "In order to do so, SoC board's specific files for firmware compilation, " +echo "testbench generation and synthesis are configured." +echo "Firmware and testbench looks for board specific files under $BACKEND_DIR." +echo "Synthesis work under $SYN_DIR." +echo "" +echo "" + +echo "Copying board specific SoC files from $BOARD_DIR to $BACKEND_DIR directory." +echo "__________________________________________________________________________" +echo "" +for file in "${BOARD_FILES[@]}" +do + if [ $file != NONE ] + then + echo "Copying $file, to backend directory..." + cp $BOARD_DIR/$file $BACKEND_DIR + fi +done +echo "" +echo "" + +echo "Generating project files for simulation and synthesis..." +echo "__________________________________________________________________________" +echo "" +make -C $MINSOC_DIR/prj +echo "Generation complete." +echo "" +echo "" + +if [ $CONSTRAINT_FILE == 'NONE' ] +then + echo "Skipping synthesis preparation. Standard implementation can only be simulated." + echo "" + echo "" +else + echo "Device part for files under $SYNSRC_DIR will be patched and stored " + echo "temporarily." + echo "Afterwards, they are copied to $SYNSUPPORT_DIR." + echo "__________________________________________________________________________" + echo "" + for file in "${SYN_FILES[@]}" + do + echo "Updating synthesis file, $file..." + echo "Copying $file to synthesis directory..." + echo "" + sed "s/$FIND_PART/$DEVICE_PART/g" $SYNSRC_DIR/$file > TMPFILE + sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYNSUPPORT_DIR/$file + rm TMPFILE + done + + echo "Updating Makefile file under $MAKEFILE_DIR..." + echo "Copying Makefile to synthesis directory, $SYN_DIR..." + echo "" + sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE + sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE + rm TMPFILE + cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat + echo "" + echo "" +fi + +echo "Configuration done."
minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/configure Property changes : Added: svn:executable ## -0,0 +1 ## +* \ No newline at end of property Index: minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/or1200_defines.v =================================================================== --- minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/or1200_defines.v (nonexistent) +++ minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/or1200_defines.v (revision 136) @@ -0,0 +1,1754 @@ +////////////////////////////////////////////////////////////////////// +//// //// +//// OR1200's definitions //// +//// //// +//// This file is part of the OpenRISC 1200 project //// +//// http://www.opencores.org/cores/or1k/ //// +//// //// +//// Description //// +//// Parameters of the OR1200 core //// +//// //// +//// To Do: //// +//// - add parameters that are missing //// +//// //// +//// Author(s): //// +//// - Damjan Lampret, lampret@opencores.org //// +//// //// +////////////////////////////////////////////////////////////////////// +//// //// +//// Copyright (C) 2000 Authors and OPENCORES.ORG //// +//// //// +//// This source file may be used and distributed without //// +//// restriction provided that this copyright statement is not //// +//// removed from the file and that any derivative work contains //// +//// the original copyright notice and the associated disclaimer. //// +//// //// +//// This source file is free software; you can redistribute it //// +//// and/or modify it under the terms of the GNU Lesser General //// +//// Public License as published by the Free Software Foundation; //// +//// either version 2.1 of the License, or (at your option) any //// +//// later version. //// +//// //// +//// This source is distributed in the hope that it will be //// +//// useful, but WITHOUT ANY WARRANTY; without even the implied //// +//// warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR //// +//// PURPOSE. See the GNU Lesser General Public License for more //// +//// details. //// +//// //// +//// You should have received a copy of the GNU Lesser General //// +//// Public License along with this source; if not, download it //// +//// from http://www.opencores.org/lgpl.shtml //// +//// //// +////////////////////////////////////////////////////////////////////// +// +// CVS Revision History +// +// $Log: not supported by cvs2svn $ +// Revision 1.44 2005/10/19 11:37:56 jcastillo +// Added support for RAMB16 Xilinx4/Spartan3 primitives +// +// Revision 1.43 2005/01/07 09:23:39 andreje +// l.ff1 and l.cmov instructions added +// +// Revision 1.42 2004/06/08 18:17:36 lampret +// Non-functional changes. Coding style fixes. +// +// Revision 1.41 2004/05/09 20:03:20 lampret +// By default l.cust5 insns are disabled +// +// Revision 1.40 2004/05/09 19:49:04 lampret +// Added some l.cust5 custom instructions as example +// +// Revision 1.39 2004/04/08 11:00:46 simont +// Add support for 512B instruction cache. +// +// Revision 1.38 2004/04/05 08:29:57 lampret +// Merged branch_qmem into main tree. +// +// Revision 1.35.4.6 2004/02/11 01:40:11 lampret +// preliminary HW breakpoints support in debug unit (by default disabled). To enable define OR1200_DU_HWBKPTS. +// +// Revision 1.35.4.5 2004/01/15 06:46:38 markom +// interface to debug changed; no more opselect; stb-ack protocol +// +// Revision 1.35.4.4 2004/01/11 22:45:46 andreje +// Separate instruction and data QMEM decoders, QMEM acknowledge and byte-select added +// +// Revision 1.35.4.3 2003/12/17 13:43:38 simons +// Exception prefix configuration changed. +// +// Revision 1.35.4.2 2003/12/05 00:05:03 lampret +// Static exception prefix. +// +// Revision 1.35.4.1 2003/07/08 15:36:37 lampret +// Added embedded memory QMEM. +// +// Revision 1.35 2003/04/24 00:16:07 lampret +// No functional changes. Added defines to disable implementation of multiplier/MAC +// +// Revision 1.34 2003/04/20 22:23:57 lampret +// No functional change. Only added customization for exception vectors. +// +// Revision 1.33 2003/04/07 20:56:07 lampret +// Fixed OR1200_CLKDIV_x_SUPPORTED defines. Better description. +// +// Revision 1.32 2003/04/07 01:26:57 lampret +// RFRAM defines comments updated. Altera LPM option added. +// +// Revision 1.31 2002/12/08 08:57:56 lampret +// Added optional support for WB B3 specification (xwb_cti_o, xwb_bte_o). Made xwb_cab_o optional. +// +// Revision 1.30 2002/10/28 15:09:22 mohor +// Previous check-in was done by mistake. +// +// Revision 1.29 2002/10/28 15:03:50 mohor +// Signal scanb_sen renamed to scanb_en. +// +// Revision 1.28 2002/10/17 20:04:40 lampret +// Added BIST scan. Special VS RAMs need to be used to implement BIST. +// +// Revision 1.27 2002/09/16 03:13:23 lampret +// Removed obsolete comment. +// +// Revision 1.26 2002/09/08 05:52:16 lampret +// Added optional l.div/l.divu insns. By default they are disabled. +// +// Revision 1.25 2002/09/07 19:16:10 lampret +// If SR[CY] implemented with OR1200_IMPL_ADDC enabled, l.add/l.addi also set SR[CY]. +// +// Revision 1.24 2002/09/07 05:42:02 lampret +// Added optional SR[CY]. Added define to enable additional (compare) flag modifiers. Defines are OR1200_IMPL_ADDC and OR1200_ADDITIONAL_FLAG_MODIFIERS. +// +// Revision 1.23 2002/09/04 00:50:34 lampret +// Now most of the configuration registers are updatded automatically based on defines in or1200_defines.v. +// +// Revision 1.22 2002/09/03 22:28:21 lampret +// As per Taylor Su suggestion all case blocks are full case by default and optionally (OR1200_CASE_DEFAULT) can be disabled to increase clock frequncy. +// +// Revision 1.21 2002/08/22 02:18:55 lampret +// Store buffer has been tested and it works. BY default it is still disabled until uClinux confirms correct operation on FPGA board. +// +// Revision 1.20 2002/08/18 21:59:45 lampret +// Disable SB until it is tested +// +// Revision 1.19 2002/08/18 19:53:08 lampret +// Added store buffer. +// +// Revision 1.18 2002/08/15 06:04:11 lampret +// Fixed Xilinx trace buffer address. REported by Taylor Su. +// +// Revision 1.17 2002/08/12 05:31:44 lampret +// Added OR1200_WB_RETRY. Moved WB registered outsputs / samples inputs into lower section. +// +// Revision 1.16 2002/07/14 22:17:17 lampret +// Added simple trace buffer [only for Xilinx Virtex target]. Fixed instruction fetch abort when new exception is recognized. +// +// Revision 1.15 2002/06/08 16:20:21 lampret +// Added defines for enabling generic FF based memory macro for register file. +// +// Revision 1.14 2002/03/29 16:24:06 lampret +// Changed comment about synopsys to _synopsys_ because synthesis was complaining about unknown directives +// +// Revision 1.13 2002/03/29 15:16:55 lampret +// Some of the warnings fixed. +// +// Revision 1.12 2002/03/28 19:25:42 lampret +// Added second type of Virtual Silicon two-port SRAM (for register file). Changed defines for VS STP RAMs. +// +// Revision 1.11 2002/03/28 19:13:17 lampret +// Updated defines. +// +// Revision 1.10 2002/03/14 00:30:24 lampret +// Added alternative for critical path in DU. +// +// Revision 1.9 2002/03/11 01:26:26 lampret +// Fixed async loop. Changed multiplier type for ASIC. +// +// Revision 1.8 2002/02/11 04:33:17 lampret +// Speed optimizations (removed duplicate _cyc_ and _stb_). Fixed D/IMMU cache-inhibit attr. +// +// Revision 1.7 2002/02/01 19:56:54 lampret +// Fixed combinational loops. +// +// Revision 1.6 2002/01/19 14:10:22 lampret +// Fixed OR1200_XILINX_RAM32X1D. +// +// Revision 1.5 2002/01/18 07:56:00 lampret +// No more low/high priority interrupts (PICPR removed). Added tick timer exception. Added exception prefix (SR[EPH]). Fixed single-step bug whenreading NPC. +// +// Revision 1.4 2002/01/14 09:44:12 lampret +// Default ASIC configuration does not sample WB inputs. +// +// Revision 1.3 2002/01/08 00:51:08 lampret +// Fixed typo. OR1200_REGISTERED_OUTPUTS was not defined. Should be. +// +// Revision 1.2 2002/01/03 21:23:03 lampret +// Uncommented OR1200_REGISTERED_OUTPUTS for FPGA target. +// +// Revision 1.1 2002/01/03 08:16:15 lampret +// New prefixes for RTL files, prefixed module names. Updated cache controllers and MMUs. +// +// Revision 1.20 2001/12/04 05:02:36 lampret +// Added OR1200_GENERIC_MULTP2_32X32 and OR1200_ASIC_MULTP2_32X32 +// +// Revision 1.19 2001/11/27 19:46:57 lampret +// Now FPGA and ASIC target are separate. +// +// Revision 1.18 2001/11/23 21:42:31 simons +// Program counter divided to PPC and NPC. +// +// Revision 1.17 2001/11/23 08:38:51 lampret +// Changed DSR/DRR behavior and exception detection. +// +// Revision 1.16 2001/11/20 21:30:38 lampret +// Added OR1200_REGISTERED_INPUTS. +// +// Revision 1.15 2001/11/19 14:29:48 simons +// Cashes disabled. +// +// Revision 1.14 2001/11/13 10:02:21 lampret +// Added 'setpc'. Renamed some signals (except_flushpipe into flushpipe etc) +// +// Revision 1.13 2001/11/12 01:45:40 lampret +// Moved flag bit into SR. Changed RF enable from constant enable to dynamic enable for read ports. +// +// Revision 1.12 2001/11/10 03:43:57 lampret +// Fixed exceptions. +// +// Revision 1.11 2001/11/02 18:57:14 lampret +// Modified virtual silicon instantiations. +// +// Revision 1.10 2001/10/21 17:57:16 lampret +// Removed params from generic_XX.v. Added translate_off/on in sprs.v and id.v. Removed spr_addr from dc.v and ic.v. Fixed CR+LF. +// +// Revision 1.9 2001/10/19 23:28:46 lampret +// Fixed some synthesis warnings. Configured with caches and MMUs. +// +// Revision 1.8 2001/10/14 13:12:09 lampret +// MP3 version. +// +// Revision 1.1.1.1 2001/10/06 10:18:36 igorm +// no message +// +// Revision 1.3 2001/08/17 08:01:19 lampret +// IC enable/disable. +// +// Revision 1.2 2001/08/13 03:36:20 lampret +// Added cfg regs. Moved all defines into one defines.v file. More cleanup. +// +// Revision 1.1 2001/08/09 13:39:33 lampret +// Major clean-up. +// +// Revision 1.2 2001/07/22 03:31:54 lampret +// Fixed RAM's oen bug. Cache bypass under development. +// +// Revision 1.1 2001/07/20 00:46:03 lampret +// Development version of RTL. Libraries are missing. +// +// + +// +// Dump VCD +// +//`define OR1200_VCD_DUMP + +// +// Generate debug messages during simulation +// +//`define OR1200_VERBOSE + +// `define OR1200_ASIC +//////////////////////////////////////////////////////// +// +// Typical configuration for an ASIC +// +`ifdef OR1200_ASIC + +// +// Target ASIC memories +// +//`define OR1200_ARTISAN_SSP +//`define OR1200_ARTISAN_SDP +//`define OR1200_ARTISAN_STP +`define OR1200_VIRTUALSILICON_SSP +//`define OR1200_VIRTUALSILICON_STP_T1 +//`define OR1200_VIRTUALSILICON_STP_T2 + +// +// Do not implement Data cache +// +//`define OR1200_NO_DC + +// +// Do not implement Insn cache +// +//`define OR1200_NO_IC + +// +// Do not implement Data MMU +// +//`define OR1200_NO_DMMU + +// +// Do not implement Insn MMU +// +//`define OR1200_NO_IMMU + +// +// Select between ASIC optimized and generic multiplier +// +//`define OR1200_ASIC_MULTP2_32X32 +`define OR1200_GENERIC_MULTP2_32X32 + +// +// Size/type of insn/data cache if implemented +// +// `define OR1200_IC_1W_512B +// `define OR1200_IC_1W_4KB +`define OR1200_IC_1W_8KB +// `define OR1200_DC_1W_4KB +`define OR1200_DC_1W_8KB + +`else + + +///////////////////////////////////////////////////////// +// +// Typical configuration for an FPGA +// + +// +// Target FPGA memories +// +//`define OR1200_ALTERA_LPM +`define OR1200_XILINX_RAMB16 +//`define OR1200_XILINX_RAMB4 +//`define OR1200_XILINX_RAM32X1D +//`define OR1200_USE_RAM16X1D_FOR_RAM32X1D + +// +// Do not implement Data cache +// +`define OR1200_NO_DC + +// +// Do not implement Insn cache +// +`define OR1200_NO_IC + +// +// Do not implement Data MMU +// +`define OR1200_NO_DMMU + +// +// Do not implement Insn MMU +// +`define OR1200_NO_IMMU + +// +// Select between ASIC and generic multiplier +// +// (Generic seems to trigger a bug in the Cadence Ncsim simulator) +// +//`define OR1200_ASIC_MULTP2_32X32 +`define OR1200_GENERIC_MULTP2_32X32 + +// +// Size/type of insn/data cache if implemented +// (consider available FPGA memory resources) +// +//`define OR1200_IC_1W_512B +`define OR1200_IC_1W_4KB +//`define OR1200_IC_1W_8KB +`define OR1200_DC_1W_4KB +//`define OR1200_DC_1W_8KB + +`endif + + +////////////////////////////////////////////////////////// +// +// Do not change below unless you know what you are doing +// + +// +// Enable RAM BIST +// +// At the moment this only works for Virtual Silicon +// single port RAMs. For other RAMs it has not effect. +// Special wrapper for VS RAMs needs to be provided +// with scan flops to facilitate bist scan. +// +//`define OR1200_BIST + +// +// Register OR1200 WISHBONE outputs +// (must be defined/enabled) +// +`define OR1200_REGISTERED_OUTPUTS + +// +// Register OR1200 WISHBONE inputs +// +// (must be undefined/disabled) +// +//`define OR1200_REGISTERED_INPUTS + +// +// Disable bursts if they are not supported by the +// memory subsystem (only affect cache line fill) +// +//`define OR1200_NO_BURSTS +// + +// +// WISHBONE retry counter range +// +// 2^value range for retry counter. Retry counter +// is activated whenever *wb_rty_i is asserted and +// until retry counter expires, corresponding +// WISHBONE interface is deactivated. +// +// To disable retry counters and *wb_rty_i all together, +// undefine this macro. +// +//`define OR1200_WB_RETRY 7 + +// +// WISHBONE Consecutive Address Burst +// +// This was used prior to WISHBONE B3 specification +// to identify bursts. It is no longer needed but +// remains enabled for compatibility with old designs. +// +// To remove *wb_cab_o ports undefine this macro. +// +`define OR1200_WB_CAB + +// +// WISHBONE B3 compatible interface +// +// This follows the WISHBONE B3 specification. +// It is not enabled by default because most +// designs still don't use WB b3. +// +// To enable *wb_cti_o/*wb_bte_o ports, +// define this macro. +// +//`define OR1200_WB_B3 + +// +// Enable additional synthesis directives if using +// _Synopsys_ synthesis tool +// +//`define OR1200_ADDITIONAL_SYNOPSYS_DIRECTIVES + +// +// Enables default statement in some case blocks +// and disables Synopsys synthesis directive full_case +// +// By default it is enabled. When disabled it +// can increase clock frequency. +// +`define OR1200_CASE_DEFAULT + +// +// Operand width / register file address width +// +// (DO NOT CHANGE) +// +`define OR1200_OPERAND_WIDTH 32 +`define OR1200_REGFILE_ADDR_WIDTH 5 + +// +// l.add/l.addi/l.and and optional l.addc/l.addic +// also set (compare) flag when result of their +// operation equals zero +// +// At the time of writing this, default or32 +// C/C++ compiler doesn't generate code that +// would benefit from this optimization. +// +// By default this optimization is disabled to +// save area. +// +//`define OR1200_ADDITIONAL_FLAG_MODIFIERS + +// +// Implement l.addc/l.addic instructions +// +// By default implementation of l.addc/l.addic +// instructions is enabled in case you need them. +// If you don't use them, then disable implementation +// to save area. +// +`define OR1200_IMPL_ADDC + +// +// Implement carry bit SR[CY] +// +// By default implementation of SR[CY] is enabled +// to be compliant with the simulator. However +// SR[CY] is explicitly only used by l.addc/l.addic +// instructions and if these two insns are not +// implemented there is not much point having SR[CY]. +// +`define OR1200_IMPL_CY + +// +// Implement optional l.div/l.divu instructions +// +// By default divide instructions are not implemented +// to save area and increase clock frequency. or32 C/C++ +// compiler can use soft library for division. +// +// To implement divide, multiplier needs to be implemented. +// +//`define OR1200_IMPL_DIV + +// +// Implement rotate in the ALU +// +// At the time of writing this, or32 +// C/C++ compiler doesn't generate rotate +// instructions. However or32 assembler +// can assemble code that uses rotate insn. +// This means that rotate instructions +// must be used manually inserted. +// +// By default implementation of rotate +// is disabled to save area and increase +// clock frequency. +// +//`define OR1200_IMPL_ALU_ROTATE + +// +// Type of ALU compare to implement +// +// Try either one to find what yields +// higher clock frequencyin your case. +// +//`define OR1200_IMPL_ALU_COMP1 +`define OR1200_IMPL_ALU_COMP2 + +// +// Implement multiplier +// +// By default multiplier is implemented +// +//`define OR1200_MULT_IMPLEMENTED + +// +// Implement multiply-and-accumulate +// +// By default MAC is implemented. To +// implement MAC, multiplier needs to be +// implemented. +// +//`define OR1200_MAC_IMPLEMENTED + +// +// Low power, slower multiplier +// +// Select between low-power (larger) multiplier +// and faster multiplier. The actual difference +// is only AND logic that prevents distribution +// of operands into the multiplier when instruction +// in execution is not multiply instruction +// +//`define OR1200_LOWPWR_MULT + +// +// Clock ratio RISC clock versus WB clock +// +// If you plan to run WB:RISC clock fixed to 1:1, disable +// both defines +// +// For WB:RISC 1:2 or 1:1, enable OR1200_CLKDIV_2_SUPPORTED +// and use clmode to set ratio +// +// For WB:RISC 1:4, 1:2 or 1:1, enable both defines and use +// clmode to set ratio +// +`define OR1200_CLKDIV_2_SUPPORTED +//`define OR1200_CLKDIV_4_SUPPORTED + +// +// Type of register file RAM +// +// Memory macro w/ two ports (see or1200_tpram_32x32.v) +//`define OR1200_RFRAM_TWOPORT +// +// Memory macro dual port (see or1200_dpram_32x32.v) +`define OR1200_RFRAM_DUALPORT +// +// Generic (flip-flop based) register file (see or1200_rfram_generic.v) +//`define OR1200_RFRAM_GENERIC + +// +// Type of mem2reg aligner to implement. +// +// Once OR1200_IMPL_MEM2REG2 yielded faster +// circuit, however with today tools it will +// most probably give you slower circuit. +// +`define OR1200_IMPL_MEM2REG1 +//`define OR1200_IMPL_MEM2REG2 + +// +// ALUOPs +// +`define OR1200_ALUOP_WIDTH 4 +`define OR1200_ALUOP_NOP 4'd4 +/* Order defined by arith insns that have two source operands both in regs + (see binutils/include/opcode/or32.h) */ +`define OR1200_ALUOP_ADD 4'd0 +`define OR1200_ALUOP_ADDC 4'd1 +`define OR1200_ALUOP_SUB 4'd2 +`define OR1200_ALUOP_AND 4'd3 +`define OR1200_ALUOP_OR 4'd4 +`define OR1200_ALUOP_XOR 4'd5 +`define OR1200_ALUOP_MUL 4'd6 +`define OR1200_ALUOP_CUST5 4'd7 +`define OR1200_ALUOP_SHROT 4'd8 +`define OR1200_ALUOP_DIV 4'd9 +`define OR1200_ALUOP_DIVU 4'd10 +/* Order not specifically defined. */ +`define OR1200_ALUOP_IMM 4'd11 +`define OR1200_ALUOP_MOVHI 4'd12 +`define OR1200_ALUOP_COMP 4'd13 +`define OR1200_ALUOP_MTSR 4'd14 +`define OR1200_ALUOP_MFSR 4'd15 +`define OR1200_ALUOP_CMOV 4'd14 +`define OR1200_ALUOP_FF1 4'd15 +// +// MACOPs +// +`define OR1200_MACOP_WIDTH 2 +`define OR1200_MACOP_NOP 2'b00 +`define OR1200_MACOP_MAC 2'b01 +`define OR1200_MACOP_MSB 2'b10 + +// +// Shift/rotate ops +// +`define OR1200_SHROTOP_WIDTH 2 +`define OR1200_SHROTOP_NOP 2'd0 +`define OR1200_SHROTOP_SLL 2'd0 +`define OR1200_SHROTOP_SRL 2'd1 +`define OR1200_SHROTOP_SRA 2'd2 +`define OR1200_SHROTOP_ROR 2'd3 + +// Execution cycles per instruction +`define OR1200_MULTICYCLE_WIDTH 2 +`define OR1200_ONE_CYCLE 2'd0 +`define OR1200_TWO_CYCLES 2'd1 + +// Operand MUX selects +`define OR1200_SEL_WIDTH 2 +`define OR1200_SEL_RF 2'd0 +`define OR1200_SEL_IMM 2'd1 +`define OR1200_SEL_EX_FORW 2'd2 +`define OR1200_SEL_WB_FORW 2'd3 + +// +// BRANCHOPs +// +`define OR1200_BRANCHOP_WIDTH 3 +`define OR1200_BRANCHOP_NOP 3'd0 +`define OR1200_BRANCHOP_J 3'd1 +`define OR1200_BRANCHOP_JR 3'd2 +`define OR1200_BRANCHOP_BAL 3'd3 +`define OR1200_BRANCHOP_BF 3'd4 +`define OR1200_BRANCHOP_BNF 3'd5 +`define OR1200_BRANCHOP_RFE 3'd6 + +// +// LSUOPs +// +// Bit 0: sign extend +// Bits 1-2: 00 doubleword, 01 byte, 10 halfword, 11 singleword +// Bit 3: 0 load, 1 store +`define OR1200_LSUOP_WIDTH 4 +`define OR1200_LSUOP_NOP 4'b0000 +`define OR1200_LSUOP_LBZ 4'b0010 +`define OR1200_LSUOP_LBS 4'b0011 +`define OR1200_LSUOP_LHZ 4'b0100 +`define OR1200_LSUOP_LHS 4'b0101 +`define OR1200_LSUOP_LWZ 4'b0110 +`define OR1200_LSUOP_LWS 4'b0111 +`define OR1200_LSUOP_LD 4'b0001 +`define OR1200_LSUOP_SD 4'b1000 +`define OR1200_LSUOP_SB 4'b1010 +`define OR1200_LSUOP_SH 4'b1100 +`define OR1200_LSUOP_SW 4'b1110 + +// FETCHOPs +`define OR1200_FETCHOP_WIDTH 1 +`define OR1200_FETCHOP_NOP 1'b0 +`define OR1200_FETCHOP_LW 1'b1 + +// +// Register File Write-Back OPs +// +// Bit 0: register file write enable +// Bits 2-1: write-back mux selects +`define OR1200_RFWBOP_WIDTH 3 +`define OR1200_RFWBOP_NOP 3'b000 +`define OR1200_RFWBOP_ALU 3'b001 +`define OR1200_RFWBOP_LSU 3'b011 +`define OR1200_RFWBOP_SPRS 3'b101 +`define OR1200_RFWBOP_LR 3'b111 + +// Compare instructions +`define OR1200_COP_SFEQ 3'b000 +`define OR1200_COP_SFNE 3'b001 +`define OR1200_COP_SFGT 3'b010 +`define OR1200_COP_SFGE 3'b011 +`define OR1200_COP_SFLT 3'b100 +`define OR1200_COP_SFLE 3'b101 +`define OR1200_COP_X 3'b111 +`define OR1200_SIGNED_COMPARE 'd3 +`define OR1200_COMPOP_WIDTH 4 + +// +// TAGs for instruction bus +// +`define OR1200_ITAG_IDLE 4'h0 // idle bus +`define OR1200_ITAG_NI 4'h1 // normal insn +`define OR1200_ITAG_BE 4'hb // Bus error exception +`define OR1200_ITAG_PE 4'hc // Page fault exception +`define OR1200_ITAG_TE 4'hd // TLB miss exception + +// +// TAGs for data bus +// +`define OR1200_DTAG_IDLE 4'h0 // idle bus +`define OR1200_DTAG_ND 4'h1 // normal data +`define OR1200_DTAG_AE 4'ha // Alignment exception +`define OR1200_DTAG_BE 4'hb // Bus error exception +`define OR1200_DTAG_PE 4'hc // Page fault exception +`define OR1200_DTAG_TE 4'hd // TLB miss exception + + +////////////////////////////////////////////// +// +// ORBIS32 ISA specifics +// + +// SHROT_OP position in machine word +`define OR1200_SHROTOP_POS 7:6 + +// ALU instructions multicycle field in machine word +`define OR1200_ALUMCYC_POS 9:8 + +// +// Instruction opcode groups (basic) +// +`define OR1200_OR32_J 6'b000000 +`define OR1200_OR32_JAL 6'b000001 +`define OR1200_OR32_BNF 6'b000011 +`define OR1200_OR32_BF 6'b000100 +`define OR1200_OR32_NOP 6'b000101 +`define OR1200_OR32_MOVHI 6'b000110 +`define OR1200_OR32_XSYNC 6'b001000 +`define OR1200_OR32_RFE 6'b001001 +/* */ +`define OR1200_OR32_JR 6'b010001 +`define OR1200_OR32_JALR 6'b010010 +`define OR1200_OR32_MACI 6'b010011 +/* */ +`define OR1200_OR32_LWZ 6'b100001 +`define OR1200_OR32_LBZ 6'b100011 +`define OR1200_OR32_LBS 6'b100100 +`define OR1200_OR32_LHZ 6'b100101 +`define OR1200_OR32_LHS 6'b100110 +`define OR1200_OR32_ADDI 6'b100111 +`define OR1200_OR32_ADDIC 6'b101000 +`define OR1200_OR32_ANDI 6'b101001 +`define OR1200_OR32_ORI 6'b101010 +`define OR1200_OR32_XORI 6'b101011 +`define OR1200_OR32_MULI 6'b101100 +`define OR1200_OR32_MFSPR 6'b101101 +`define OR1200_OR32_SH_ROTI 6'b101110 +`define OR1200_OR32_SFXXI 6'b101111 +/* */ +`define OR1200_OR32_MTSPR 6'b110000 +`define OR1200_OR32_MACMSB 6'b110001 +/* */ +`define OR1200_OR32_SW 6'b110101 +`define OR1200_OR32_SB 6'b110110 +`define OR1200_OR32_SH 6'b110111 +`define OR1200_OR32_ALU 6'b111000 +`define OR1200_OR32_SFXX 6'b111001 +//`define OR1200_OR32_CUST5 6'b111100 + + +///////////////////////////////////////////////////// +// +// Exceptions +// + +// +// Exception vectors per OR1K architecture: +// 0xPPPPP100 - reset +// 0xPPPPP200 - bus error +// ... etc +// where P represents exception prefix. +// +// Exception vectors can be customized as per +// the following formula: +// 0xPPPPPNVV - exception N +// +// P represents exception prefix +// N represents exception N +// VV represents length of the individual vector space, +// usually it is 8 bits wide and starts with all bits zero +// + +// +// PPPPP and VV parts +// +// Sum of these two defines needs to be 28 +// +`define OR1200_EXCEPT_EPH0_P 20'h00000 +`define OR1200_EXCEPT_EPH1_P 20'hF0000 +`define OR1200_EXCEPT_V 8'h00 + +// +// N part width +// +`define OR1200_EXCEPT_WIDTH 4 + +// +// Definition of exception vectors +// +// To avoid implementation of a certain exception, +// simply comment out corresponding line +// +`define OR1200_EXCEPT_UNUSED `OR1200_EXCEPT_WIDTH'hf +`define OR1200_EXCEPT_TRAP `OR1200_EXCEPT_WIDTH'he +`define OR1200_EXCEPT_BREAK `OR1200_EXCEPT_WIDTH'hd +`define OR1200_EXCEPT_SYSCALL `OR1200_EXCEPT_WIDTH'hc +`define OR1200_EXCEPT_RANGE `OR1200_EXCEPT_WIDTH'hb +`define OR1200_EXCEPT_ITLBMISS `OR1200_EXCEPT_WIDTH'ha +`define OR1200_EXCEPT_DTLBMISS `OR1200_EXCEPT_WIDTH'h9 +`define OR1200_EXCEPT_INT `OR1200_EXCEPT_WIDTH'h8 +`define OR1200_EXCEPT_ILLEGAL `OR1200_EXCEPT_WIDTH'h7 +`define OR1200_EXCEPT_ALIGN `OR1200_EXCEPT_WIDTH'h6 +`define OR1200_EXCEPT_TICK `OR1200_EXCEPT_WIDTH'h5 +`define OR1200_EXCEPT_IPF `OR1200_EXCEPT_WIDTH'h4 +`define OR1200_EXCEPT_DPF `OR1200_EXCEPT_WIDTH'h3 +`define OR1200_EXCEPT_BUSERR `OR1200_EXCEPT_WIDTH'h2 +`define OR1200_EXCEPT_RESET `OR1200_EXCEPT_WIDTH'h1 +`define OR1200_EXCEPT_NONE `OR1200_EXCEPT_WIDTH'h0 + + +///////////////////////////////////////////////////// +// +// SPR groups +// + +// Bits that define the group +`define OR1200_SPR_GROUP_BITS 15:11 + +// Width of the group bits +`define OR1200_SPR_GROUP_WIDTH 5 + +// Bits that define offset inside the group +`define OR1200_SPR_OFS_BITS 10:0 + +// List of groups +`define OR1200_SPR_GROUP_SYS 5'd00 +`define OR1200_SPR_GROUP_DMMU 5'd01 +`define OR1200_SPR_GROUP_IMMU 5'd02 +`define OR1200_SPR_GROUP_DC 5'd03 +`define OR1200_SPR_GROUP_IC 5'd04 +`define OR1200_SPR_GROUP_MAC 5'd05 +`define OR1200_SPR_GROUP_DU 5'd06 +`define OR1200_SPR_GROUP_PM 5'd08 +`define OR1200_SPR_GROUP_PIC 5'd09 +`define OR1200_SPR_GROUP_TT 5'd10 + + +///////////////////////////////////////////////////// +// +// System group +// + +// +// System registers +// +`define OR1200_SPR_CFGR 7'd0 +`define OR1200_SPR_RF 6'd32 // 1024 >> 5 +`define OR1200_SPR_NPC 11'd16 +`define OR1200_SPR_SR 11'd17 +`define OR1200_SPR_PPC 11'd18 +`define OR1200_SPR_EPCR 11'd32 +`define OR1200_SPR_EEAR 11'd48 +`define OR1200_SPR_ESR 11'd64 + +// +// SR bits +// +`define OR1200_SR_WIDTH 16 +`define OR1200_SR_SM 0 +`define OR1200_SR_TEE 1 +`define OR1200_SR_IEE 2 +`define OR1200_SR_DCE 3 +`define OR1200_SR_ICE 4 +`define OR1200_SR_DME 5 +`define OR1200_SR_IME 6 +`define OR1200_SR_LEE 7 +`define OR1200_SR_CE 8 +`define OR1200_SR_F 9 +`define OR1200_SR_CY 10 // Unused +`define OR1200_SR_OV 11 // Unused +`define OR1200_SR_OVE 12 // Unused +`define OR1200_SR_DSX 13 // Unused +`define OR1200_SR_EPH 14 +`define OR1200_SR_FO 15 +`define OR1200_SR_CID 31:28 // Unimplemented + +// +// Bits that define offset inside the group +// +`define OR1200_SPROFS_BITS 10:0 + +// +// Default Exception Prefix +// +// 1'b0 - OR1200_EXCEPT_EPH0_P (0x0000_0000) +// 1'b1 - OR1200_EXCEPT_EPH1_P (0xF000_0000) +// +`define OR1200_SR_EPH_DEF 1'b0 + +///////////////////////////////////////////////////// +// +// Power Management (PM) +// + +// Define it if you want PM implemented +//`define OR1200_PM_IMPLEMENTED + +// Bit positions inside PMR (don't change) +`define OR1200_PM_PMR_SDF 3:0 +`define OR1200_PM_PMR_DME 4 +`define OR1200_PM_PMR_SME 5 +`define OR1200_PM_PMR_DCGE 6 +`define OR1200_PM_PMR_UNUSED 31:7 + +// PMR offset inside PM group of registers +`define OR1200_PM_OFS_PMR 11'b0 + +// PM group +`define OR1200_SPRGRP_PM 5'd8 + +// Define if PMR can be read/written at any address inside PM group +`define OR1200_PM_PARTIAL_DECODING + +// Define if reading PMR is allowed +`define OR1200_PM_READREGS + +// Define if unused PMR bits should be zero +`define OR1200_PM_UNUSED_ZERO + + +///////////////////////////////////////////////////// +// +// Debug Unit (DU) +// + +// Define it if you want DU implemented +`define OR1200_DU_IMPLEMENTED + +// +// Define if you want HW Breakpoints +// (if HW breakpoints are not implemented +// only default software trapping is +// possible with l.trap insn - this is +// however already enough for use +// with or32 gdb) +// +`define OR1200_DU_HWBKPTS + +// Number of DVR/DCR pairs if HW breakpoints enabled +`define OR1200_DU_DVRDCR_PAIRS 8 + +// Define if you want trace buffer +//`define OR1200_DU_TB_IMPLEMENTED + +// +// Address offsets of DU registers inside DU group +// +// To not implement a register, doq not define its address +// +`ifdef OR1200_DU_HWBKPTS +`define OR1200_DU_DVR0 11'd0 +`define OR1200_DU_DVR1 11'd1 +`define OR1200_DU_DVR2 11'd2 +`define OR1200_DU_DVR3 11'd3 +`define OR1200_DU_DVR4 11'd4 +`define OR1200_DU_DVR5 11'd5 +`define OR1200_DU_DVR6 11'd6 +`define OR1200_DU_DVR7 11'd7 +`define OR1200_DU_DCR0 11'd8 +`define OR1200_DU_DCR1 11'd9 +`define OR1200_DU_DCR2 11'd10 +`define OR1200_DU_DCR3 11'd11 +`define OR1200_DU_DCR4 11'd12 +`define OR1200_DU_DCR5 11'd13 +`define OR1200_DU_DCR6 11'd14 +`define OR1200_DU_DCR7 11'd15 +`endif +`define OR1200_DU_DMR1 11'd16 +`ifdef OR1200_DU_HWBKPTS +`define OR1200_DU_DMR2 11'd17 +`define OR1200_DU_DWCR0 11'd18 +`define OR1200_DU_DWCR1 11'd19 +`endif +`define OR1200_DU_DSR 11'd20 +`define OR1200_DU_DRR 11'd21 +`ifdef OR1200_DU_TB_IMPLEMENTED +`define OR1200_DU_TBADR 11'h0ff +`define OR1200_DU_TBIA 11'h1xx +`define OR1200_DU_TBIM 11'h2xx +`define OR1200_DU_TBAR 11'h3xx +`define OR1200_DU_TBTS 11'h4xx +`endif + +// Position of offset bits inside SPR address +`define OR1200_DUOFS_BITS 10:0 + +// DCR bits +`define OR1200_DU_DCR_DP 0 +`define OR1200_DU_DCR_CC 3:1 +`define OR1200_DU_DCR_SC 4 +`define OR1200_DU_DCR_CT 7:5 + +// DMR1 bits +`define OR1200_DU_DMR1_CW0 1:0 +`define OR1200_DU_DMR1_CW1 3:2 +`define OR1200_DU_DMR1_CW2 5:4 +`define OR1200_DU_DMR1_CW3 7:6 +`define OR1200_DU_DMR1_CW4 9:8 +`define OR1200_DU_DMR1_CW5 11:10 +`define OR1200_DU_DMR1_CW6 13:12 +`define OR1200_DU_DMR1_CW7 15:14 +`define OR1200_DU_DMR1_CW8 17:16 +`define OR1200_DU_DMR1_CW9 19:18 +`define OR1200_DU_DMR1_RES 21:20 +`define OR1200_DU_DMR1_ST 22 +`define OR1200_DU_DMR1_BT 23 + +// DMR2 bits +`define OR1200_DU_DMR2_WCE0 0 +`define OR1200_DU_DMR2_WCE1 1 +`define OR1200_DU_DMR2_AWTC 11:2 +`define OR1200_DU_DMR2_WGB 21:12 + +// DWCR bits +`define OR1200_DU_DWCR_COUNT 15:0 +`define OR1200_DU_DWCR_MATCH 31:16 + +// DSR bits +`define OR1200_DU_DSR_WIDTH 14 +`define OR1200_DU_DSR_RSTE 0 +`define OR1200_DU_DSR_BUSEE 1 +`define OR1200_DU_DSR_DPFE 2 +`define OR1200_DU_DSR_IPFE 3 +`define OR1200_DU_DSR_TTE 4 +`define OR1200_DU_DSR_AE 5 +`define OR1200_DU_DSR_IIE 6 +`define OR1200_DU_DSR_IE 7 +`define OR1200_DU_DSR_DME 8 +`define OR1200_DU_DSR_IME 9 +`define OR1200_DU_DSR_RE 10 +`define OR1200_DU_DSR_SCE 11 +`define OR1200_DU_DSR_BE 12 +`define OR1200_DU_DSR_TE 13 + +// DRR bits +`define OR1200_DU_DRR_RSTE 0 +`define OR1200_DU_DRR_BUSEE 1 +`define OR1200_DU_DRR_DPFE 2 +`define OR1200_DU_DRR_IPFE 3 +`define OR1200_DU_DRR_TTE 4 +`define OR1200_DU_DRR_AE 5 +`define OR1200_DU_DRR_IIE 6 +`define OR1200_DU_DRR_IE 7 +`define OR1200_DU_DRR_DME 8 +`define OR1200_DU_DRR_IME 9 +`define OR1200_DU_DRR_RE 10 +`define OR1200_DU_DRR_SCE 11 +`define OR1200_DU_DRR_BE 12 +`define OR1200_DU_DRR_TE 13 + +// Define if reading DU regs is allowed +`define OR1200_DU_READREGS + +// Define if unused DU registers bits should be zero +`define OR1200_DU_UNUSED_ZERO + +// Define if IF/LSU status is not needed by devel i/f +`define OR1200_DU_STATUS_UNIMPLEMENTED + +///////////////////////////////////////////////////// +// +// Programmable Interrupt Controller (PIC) +// + +// Define it if you want PIC implemented +`define OR1200_PIC_IMPLEMENTED + +// Define number of interrupt inputs (2-31) +`define OR1200_PIC_INTS 20 + +// Address offsets of PIC registers inside PIC group +`define OR1200_PIC_OFS_PICMR 2'd0 +`define OR1200_PIC_OFS_PICSR 2'd2 + +// Position of offset bits inside SPR address +`define OR1200_PICOFS_BITS 1:0 + +// Define if you want these PIC registers to be implemented +`define OR1200_PIC_PICMR +`define OR1200_PIC_PICSR + +// Define if reading PIC registers is allowed +`define OR1200_PIC_READREGS + +// Define if unused PIC register bits should be zero +`define OR1200_PIC_UNUSED_ZERO + + +///////////////////////////////////////////////////// +// +// Tick Timer (TT) +// + +// Define it if you want TT implemented +`define OR1200_TT_IMPLEMENTED + +// Address offsets of TT registers inside TT group +`define OR1200_TT_OFS_TTMR 1'd0 +`define OR1200_TT_OFS_TTCR 1'd1 + +// Position of offset bits inside SPR group +`define OR1200_TTOFS_BITS 0 + +// Define if you want these TT registers to be implemented +`define OR1200_TT_TTMR +`define OR1200_TT_TTCR + +// TTMR bits +`define OR1200_TT_TTMR_TP 27:0 +`define OR1200_TT_TTMR_IP 28 +`define OR1200_TT_TTMR_IE 29 +`define OR1200_TT_TTMR_M 31:30 + +// Define if reading TT registers is allowed +`define OR1200_TT_READREGS + + +////////////////////////////////////////////// +// +// MAC +// +`define OR1200_MAC_ADDR 0 // MACLO 0xxxxxxxx1, MACHI 0xxxxxxxx0 +`define OR1200_MAC_SPR_WE // Define if MACLO/MACHI are SPR writable + +// +// Shift {MACHI,MACLO} into destination register when executing l.macrc +// +// According to architecture manual there is no shift, so default value is 0. +// +// However the implementation has deviated in this from the arch manual and had hard coded shift by 28 bits which +// is a useful optimization for MP3 decoding (if using libmad fixed point library). Shifts are no longer +// default setup, but if you need to remain backward compatible, define your shift bits, which were normally +// dest_GPR = {MACHI,MACLO}[59:28] +`define OR1200_MAC_SHIFTBY 0 // 0 = According to arch manual, 28 = obsolete backward compatibility + + +////////////////////////////////////////////// +// +// Data MMU (DMMU) +// + +// +// Address that selects between TLB TR and MR +// +`define OR1200_DTLB_TM_ADDR 7 + +// +// DTLBMR fields +// +`define OR1200_DTLBMR_V_BITS 0 +`define OR1200_DTLBMR_CID_BITS 4:1 +`define OR1200_DTLBMR_RES_BITS 11:5 +`define OR1200_DTLBMR_VPN_BITS 31:13 + +// +// DTLBTR fields +// +`define OR1200_DTLBTR_CC_BITS 0 +`define OR1200_DTLBTR_CI_BITS 1 +`define OR1200_DTLBTR_WBC_BITS 2 +`define OR1200_DTLBTR_WOM_BITS 3 +`define OR1200_DTLBTR_A_BITS 4 +`define OR1200_DTLBTR_D_BITS 5 +`define OR1200_DTLBTR_URE_BITS 6 +`define OR1200_DTLBTR_UWE_BITS 7 +`define OR1200_DTLBTR_SRE_BITS 8 +`define OR1200_DTLBTR_SWE_BITS 9 +`define OR1200_DTLBTR_RES_BITS 11:10 +`define OR1200_DTLBTR_PPN_BITS 31:13 + +// +// DTLB configuration +// +`define OR1200_DMMU_PS 13 // 13 for 8KB page size +`define OR1200_DTLB_INDXW 6 // 6 for 64 entry DTLB 7 for 128 entries +`define OR1200_DTLB_INDXL `OR1200_DMMU_PS // 13 13 +`define OR1200_DTLB_INDXH `OR1200_DMMU_PS+`OR1200_DTLB_INDXW-1 // 18 19 +`define OR1200_DTLB_INDX `OR1200_DTLB_INDXH:`OR1200_DTLB_INDXL // 18:13 19:13 +`define OR1200_DTLB_TAGW 32-`OR1200_DTLB_INDXW-`OR1200_DMMU_PS // 13 12 +`define OR1200_DTLB_TAGL `OR1200_DTLB_INDXH+1 // 19 20 +`define OR1200_DTLB_TAG 31:`OR1200_DTLB_TAGL // 31:19 31:20 +`define OR1200_DTLBMRW `OR1200_DTLB_TAGW+1 // +1 because of V bit +`define OR1200_DTLBTRW 32-`OR1200_DMMU_PS+5 // +5 because of protection bits and CI + +// +// Cache inhibit while DMMU is not enabled/implemented +// +// cache inhibited 0GB-4GB 1'b1 +// cache inhibited 0GB-2GB !dcpu_adr_i[31] +// cache inhibited 0GB-1GB 2GB-3GB !dcpu_adr_i[30] +// cache inhibited 1GB-2GB 3GB-4GB dcpu_adr_i[30] +// cache inhibited 2GB-4GB (default) dcpu_adr_i[31] +// cached 0GB-4GB 1'b0 +// +`define OR1200_DMMU_CI dcpu_adr_i[31] + + +////////////////////////////////////////////// +// +// Insn MMU (IMMU) +// + +// +// Address that selects between TLB TR and MR +// +`define OR1200_ITLB_TM_ADDR 7 + +// +// ITLBMR fields +// +`define OR1200_ITLBMR_V_BITS 0 +`define OR1200_ITLBMR_CID_BITS 4:1 +`define OR1200_ITLBMR_RES_BITS 11:5 +`define OR1200_ITLBMR_VPN_BITS 31:13 + +// +// ITLBTR fields +// +`define OR1200_ITLBTR_CC_BITS 0 +`define OR1200_ITLBTR_CI_BITS 1 +`define OR1200_ITLBTR_WBC_BITS 2 +`define OR1200_ITLBTR_WOM_BITS 3 +`define OR1200_ITLBTR_A_BITS 4 +`define OR1200_ITLBTR_D_BITS 5 +`define OR1200_ITLBTR_SXE_BITS 6 +`define OR1200_ITLBTR_UXE_BITS 7 +`define OR1200_ITLBTR_RES_BITS 11:8 +`define OR1200_ITLBTR_PPN_BITS 31:13 + +// +// ITLB configuration +// +`define OR1200_IMMU_PS 13 // 13 for 8KB page size +`define OR1200_ITLB_INDXW 6 // 6 for 64 entry ITLB 7 for 128 entries +`define OR1200_ITLB_INDXL `OR1200_IMMU_PS // 13 13 +`define OR1200_ITLB_INDXH `OR1200_IMMU_PS+`OR1200_ITLB_INDXW-1 // 18 19 +`define OR1200_ITLB_INDX `OR1200_ITLB_INDXH:`OR1200_ITLB_INDXL // 18:13 19:13 +`define OR1200_ITLB_TAGW 32-`OR1200_ITLB_INDXW-`OR1200_IMMU_PS // 13 12 +`define OR1200_ITLB_TAGL `OR1200_ITLB_INDXH+1 // 19 20 +`define OR1200_ITLB_TAG 31:`OR1200_ITLB_TAGL // 31:19 31:20 +`define OR1200_ITLBMRW `OR1200_ITLB_TAGW+1 // +1 because of V bit +`define OR1200_ITLBTRW 32-`OR1200_IMMU_PS+3 // +3 because of protection bits and CI + +// +// Cache inhibit while IMMU is not enabled/implemented +// Note: all combinations that use icpu_adr_i cause async loop +// +// cache inhibited 0GB-4GB 1'b1 +// cache inhibited 0GB-2GB !icpu_adr_i[31] +// cache inhibited 0GB-1GB 2GB-3GB !icpu_adr_i[30] +// cache inhibited 1GB-2GB 3GB-4GB icpu_adr_i[30] +// cache inhibited 2GB-4GB (default) icpu_adr_i[31] +// cached 0GB-4GB 1'b0 +// +`define OR1200_IMMU_CI 1'b0 + + +///////////////////////////////////////////////// +// +// Insn cache (IC) +// + +// 3 for 8 bytes, 4 for 16 bytes etc +`define OR1200_ICLS 4 + +// +// IC configurations +// +`ifdef OR1200_IC_1W_512B +`define OR1200_ICSIZE 9 // 512 +`define OR1200_ICINDX `OR1200_ICSIZE-2 // 7 +`define OR1200_ICINDXH `OR1200_ICSIZE-1 // 8 +`define OR1200_ICTAGL `OR1200_ICINDXH+1 // 9 +`define OR1200_ICTAG `OR1200_ICSIZE-`OR1200_ICLS // 5 +`define OR1200_ICTAG_W 24 +`endif +`ifdef OR1200_IC_1W_4KB +`define OR1200_ICSIZE 12 // 4096 +`define OR1200_ICINDX `OR1200_ICSIZE-2 // 10 +`define OR1200_ICINDXH `OR1200_ICSIZE-1 // 11 +`define OR1200_ICTAGL `OR1200_ICINDXH+1 // 12 +`define OR1200_ICTAG `OR1200_ICSIZE-`OR1200_ICLS // 8 +`define OR1200_ICTAG_W 21 +`endif +`ifdef OR1200_IC_1W_8KB +`define OR1200_ICSIZE 13 // 8192 +`define OR1200_ICINDX `OR1200_ICSIZE-2 // 11 +`define OR1200_ICINDXH `OR1200_ICSIZE-1 // 12 +`define OR1200_ICTAGL `OR1200_ICINDXH+1 // 13 +`define OR1200_ICTAG `OR1200_ICSIZE-`OR1200_ICLS // 9 +`define OR1200_ICTAG_W 20 +`endif + + +///////////////////////////////////////////////// +// +// Data cache (DC) +// + +// 3 for 8 bytes, 4 for 16 bytes etc +`define OR1200_DCLS 4 + +// Define to perform store refill (potential performance penalty) +// `define OR1200_DC_STORE_REFILL + +// +// DC configurations +// +`ifdef OR1200_DC_1W_4KB +`define OR1200_DCSIZE 12 // 4096 +`define OR1200_DCINDX `OR1200_DCSIZE-2 // 10 +`define OR1200_DCINDXH `OR1200_DCSIZE-1 // 11 +`define OR1200_DCTAGL `OR1200_DCINDXH+1 // 12 +`define OR1200_DCTAG `OR1200_DCSIZE-`OR1200_DCLS // 8 +`define OR1200_DCTAG_W 21 +`endif +`ifdef OR1200_DC_1W_8KB +`define OR1200_DCSIZE 13 // 8192 +`define OR1200_DCINDX `OR1200_DCSIZE-2 // 11 +`define OR1200_DCINDXH `OR1200_DCSIZE-1 // 12 +`define OR1200_DCTAGL `OR1200_DCINDXH+1 // 13 +`define OR1200_DCTAG `OR1200_DCSIZE-`OR1200_DCLS // 9 +`define OR1200_DCTAG_W 20 +`endif + +///////////////////////////////////////////////// +// +// Store buffer (SB) +// + +// +// Store buffer +// +// It will improve performance by "caching" CPU stores +// using store buffer. This is most important for function +// prologues because DC can only work in write though mode +// and all stores would have to complete external WB writes +// to memory. +// Store buffer is between DC and data BIU. +// All stores will be stored into store buffer and immediately +// completed by the CPU, even though actual external writes +// will be performed later. As a consequence store buffer masks +// all data bus errors related to stores (data bus errors +// related to loads are delivered normally). +// All pending CPU loads will wait until store buffer is empty to +// ensure strict memory model. Right now this is necessary because +// we don't make destinction between cached and cache inhibited +// address space, so we simply empty store buffer until loads +// can begin. +// +// It makes design a bit bigger, depending what is the number of +// entries in SB FIFO. Number of entries can be changed further +// down. +// +//`define OR1200_SB_IMPLEMENTED + +// +// Number of store buffer entries +// +// Verified number of entries are 4 and 8 entries +// (2 and 3 for OR1200_SB_LOG). OR1200_SB_ENTRIES must +// always match 2**OR1200_SB_LOG. +// To disable store buffer, undefine +// OR1200_SB_IMPLEMENTED. +// +`define OR1200_SB_LOG 2 // 2 or 3 +`define OR1200_SB_ENTRIES 4 // 4 or 8 + + +///////////////////////////////////////////////// +// +// Quick Embedded Memory (QMEM) +// + +// +// Quick Embedded Memory +// +// Instantiation of dedicated insn/data memory (RAM or ROM). +// Insn fetch has effective throughput 1insn / clock cycle. +// Data load takes two clock cycles / access, data store +// takes 1 clock cycle / access (if there is no insn fetch)). +// Memory instantiation is shared between insn and data, +// meaning if insn fetch are performed, data load/store +// performance will be lower. +// +// Main reason for QMEM is to put some time critical functions +// into this memory and to have predictable and fast access +// to these functions. (soft fpu, context switch, exception +// handlers, stack, etc) +// +// It makes design a bit bigger and slower. QMEM sits behind +// IMMU/DMMU so all addresses are physical (so the MMUs can be +// used with QMEM and QMEM is seen by the CPU just like any other +// memory in the system). IC/DC are sitting behind QMEM so the +// whole design timing might be worse with QMEM implemented. +// +//`define OR1200_QMEM_IMPLEMENTED + +// +// Base address and mask of QMEM +// +// Base address defines first address of QMEM. Mask defines +// QMEM range in address space. Actual size of QMEM is however +// determined with instantiated RAM/ROM. However bigger +// mask will reserve more address space for QMEM, but also +// make design faster, while more tight mask will take +// less address space but also make design slower. If +// instantiated RAM/ROM is smaller than space reserved with +// the mask, instatiated RAM/ROM will also be shadowed +// at higher addresses in reserved space. +// +`define OR1200_QMEM_IADDR 32'h0080_0000 +`define OR1200_QMEM_IMASK 32'hfff0_0000 // Max QMEM size 1MB +`define OR1200_QMEM_DADDR 32'h0080_0000 +`define OR1200_QMEM_DMASK 32'hfff0_0000 // Max QMEM size 1MB + +// +// QMEM interface byte-select capability +// +// To enable qmem_sel* ports, define this macro. +// +//`define OR1200_QMEM_BSEL + +// +// QMEM interface acknowledge +// +// To enable qmem_ack port, define this macro. +// +//`define OR1200_QMEM_ACK + +///////////////////////////////////////////////////// +// +// VR, UPR and Configuration Registers +// +// +// VR, UPR and configuration registers are optional. If +// implemented, operating system can automatically figure +// out how to use the processor because it knows +// what units are available in the processor and how they +// are configured. +// +// This section must be last in or1200_defines.v file so +// that all units are already configured and thus +// configuration registers are properly set. +// + +// Define if you want configuration registers implemented +//`define OR1200_CFGR_IMPLEMENTED + +// Define if you want full address decode inside SYS group +`define OR1200_SYS_FULL_DECODE + +// Offsets of VR, UPR and CFGR registers +`define OR1200_SPRGRP_SYS_VR 4'h0 +`define OR1200_SPRGRP_SYS_UPR 4'h1 +`define OR1200_SPRGRP_SYS_CPUCFGR 4'h2 +`define OR1200_SPRGRP_SYS_DMMUCFGR 4'h3 +`define OR1200_SPRGRP_SYS_IMMUCFGR 4'h4 +`define OR1200_SPRGRP_SYS_DCCFGR 4'h5 +`define OR1200_SPRGRP_SYS_ICCFGR 4'h6 +`define OR1200_SPRGRP_SYS_DCFGR 4'h7 + +// VR fields +`define OR1200_VR_REV_BITS 5:0 +`define OR1200_VR_RES1_BITS 15:6 +`define OR1200_VR_CFG_BITS 23:16 +`define OR1200_VR_VER_BITS 31:24 + +// VR values +`define OR1200_VR_REV 6'h01 +`define OR1200_VR_RES1 10'h000 +`define OR1200_VR_CFG 8'h00 +`define OR1200_VR_VER 8'h12 + +// UPR fields +`define OR1200_UPR_UP_BITS 0 +`define OR1200_UPR_DCP_BITS 1 +`define OR1200_UPR_ICP_BITS 2 +`define OR1200_UPR_DMP_BITS 3 +`define OR1200_UPR_IMP_BITS 4 +`define OR1200_UPR_MP_BITS 5 +`define OR1200_UPR_DUP_BITS 6 +`define OR1200_UPR_PCUP_BITS 7 +`define OR1200_UPR_PMP_BITS 8 +`define OR1200_UPR_PICP_BITS 9 +`define OR1200_UPR_TTP_BITS 10 +`define OR1200_UPR_RES1_BITS 23:11 +`define OR1200_UPR_CUP_BITS 31:24 + +// UPR values +`define OR1200_UPR_UP 1'b1 +`ifdef OR1200_NO_DC +`define OR1200_UPR_DCP 1'b0 +`else +`define OR1200_UPR_DCP 1'b1 +`endif +`ifdef OR1200_NO_IC +`define OR1200_UPR_ICP 1'b0 +`else +`define OR1200_UPR_ICP 1'b1 +`endif +`ifdef OR1200_NO_DMMU +`define OR1200_UPR_DMP 1'b0 +`else +`define OR1200_UPR_DMP 1'b1 +`endif +`ifdef OR1200_NO_IMMU +`define OR1200_UPR_IMP 1'b0 +`else +`define OR1200_UPR_IMP 1'b1 +`endif +`define OR1200_UPR_MP 1'b1 // MAC always present +`ifdef OR1200_DU_IMPLEMENTED +`define OR1200_UPR_DUP 1'b1 +`else +`define OR1200_UPR_DUP 1'b0 +`endif +`define OR1200_UPR_PCUP 1'b0 // Performance counters not present +`ifdef OR1200_DU_IMPLEMENTED +`define OR1200_UPR_PMP 1'b1 +`else +`define OR1200_UPR_PMP 1'b0 +`endif +`ifdef OR1200_DU_IMPLEMENTED +`define OR1200_UPR_PICP 1'b1 +`else +`define OR1200_UPR_PICP 1'b0 +`endif +`ifdef OR1200_DU_IMPLEMENTED +`define OR1200_UPR_TTP 1'b1 +`else +`define OR1200_UPR_TTP 1'b0 +`endif +`define OR1200_UPR_RES1 13'h0000 +`define OR1200_UPR_CUP 8'h00 + +// CPUCFGR fields +`define OR1200_CPUCFGR_NSGF_BITS 3:0 +`define OR1200_CPUCFGR_HGF_BITS 4 +`define OR1200_CPUCFGR_OB32S_BITS 5 +`define OR1200_CPUCFGR_OB64S_BITS 6 +`define OR1200_CPUCFGR_OF32S_BITS 7 +`define OR1200_CPUCFGR_OF64S_BITS 8 +`define OR1200_CPUCFGR_OV64S_BITS 9 +`define OR1200_CPUCFGR_RES1_BITS 31:10 + +// CPUCFGR values +`define OR1200_CPUCFGR_NSGF 4'h0 +`define OR1200_CPUCFGR_HGF 1'b0 +`define OR1200_CPUCFGR_OB32S 1'b1 +`define OR1200_CPUCFGR_OB64S 1'b0 +`define OR1200_CPUCFGR_OF32S 1'b0 +`define OR1200_CPUCFGR_OF64S 1'b0 +`define OR1200_CPUCFGR_OV64S 1'b0 +`define OR1200_CPUCFGR_RES1 22'h000000 + +// DMMUCFGR fields +`define OR1200_DMMUCFGR_NTW_BITS 1:0 +`define OR1200_DMMUCFGR_NTS_BITS 4:2 +`define OR1200_DMMUCFGR_NAE_BITS 7:5 +`define OR1200_DMMUCFGR_CRI_BITS 8 +`define OR1200_DMMUCFGR_PRI_BITS 9 +`define OR1200_DMMUCFGR_TEIRI_BITS 10 +`define OR1200_DMMUCFGR_HTR_BITS 11 +`define OR1200_DMMUCFGR_RES1_BITS 31:12 + +// DMMUCFGR values +`ifdef OR1200_NO_DMMU +`define OR1200_DMMUCFGR_NTW 2'h0 // Irrelevant +`define OR1200_DMMUCFGR_NTS 3'h0 // Irrelevant +`define OR1200_DMMUCFGR_NAE 3'h0 // Irrelevant +`define OR1200_DMMUCFGR_CRI 1'b0 // Irrelevant +`define OR1200_DMMUCFGR_PRI 1'b0 // Irrelevant +`define OR1200_DMMUCFGR_TEIRI 1'b0 // Irrelevant +`define OR1200_DMMUCFGR_HTR 1'b0 // Irrelevant +`define OR1200_DMMUCFGR_RES1 20'h00000 +`else +`define OR1200_DMMUCFGR_NTW 2'h0 // 1 TLB way +`define OR1200_DMMUCFGR_NTS 3'h`OR1200_DTLB_INDXW // Num TLB sets +`define OR1200_DMMUCFGR_NAE 3'h0 // No ATB entries +`define OR1200_DMMUCFGR_CRI 1'b0 // No control register +`define OR1200_DMMUCFGR_PRI 1'b0 // No protection reg +`define OR1200_DMMUCFGR_TEIRI 1'b1 // TLB entry inv reg impl. +`define OR1200_DMMUCFGR_HTR 1'b0 // No HW TLB reload +`define OR1200_DMMUCFGR_RES1 20'h00000 +`endif + +// IMMUCFGR fields +`define OR1200_IMMUCFGR_NTW_BITS 1:0 +`define OR1200_IMMUCFGR_NTS_BITS 4:2 +`define OR1200_IMMUCFGR_NAE_BITS 7:5 +`define OR1200_IMMUCFGR_CRI_BITS 8 +`define OR1200_IMMUCFGR_PRI_BITS 9 +`define OR1200_IMMUCFGR_TEIRI_BITS 10 +`define OR1200_IMMUCFGR_HTR_BITS 11 +`define OR1200_IMMUCFGR_RES1_BITS 31:12 + +// IMMUCFGR values +`ifdef OR1200_NO_IMMU +`define OR1200_IMMUCFGR_NTW 2'h0 // Irrelevant +`define OR1200_IMMUCFGR_NTS 3'h0 // Irrelevant +`define OR1200_IMMUCFGR_NAE 3'h0 // Irrelevant +`define OR1200_IMMUCFGR_CRI 1'b0 // Irrelevant +`define OR1200_IMMUCFGR_PRI 1'b0 // Irrelevant +`define OR1200_IMMUCFGR_TEIRI 1'b0 // Irrelevant +`define OR1200_IMMUCFGR_HTR 1'b0 // Irrelevant +`define OR1200_IMMUCFGR_RES1 20'h00000 +`else +`define OR1200_IMMUCFGR_NTW 2'h0 // 1 TLB way +`define OR1200_IMMUCFGR_NTS 3'h`OR1200_ITLB_INDXW // Num TLB sets +`define OR1200_IMMUCFGR_NAE 3'h0 // No ATB entry +`define OR1200_IMMUCFGR_CRI 1'b0 // No control reg +`define OR1200_IMMUCFGR_PRI 1'b0 // No protection reg +`define OR1200_IMMUCFGR_TEIRI 1'b1 // TLB entry inv reg impl +`define OR1200_IMMUCFGR_HTR 1'b0 // No HW TLB reload +`define OR1200_IMMUCFGR_RES1 20'h00000 +`endif + +// DCCFGR fields +`define OR1200_DCCFGR_NCW_BITS 2:0 +`define OR1200_DCCFGR_NCS_BITS 6:3 +`define OR1200_DCCFGR_CBS_BITS 7 +`define OR1200_DCCFGR_CWS_BITS 8 +`define OR1200_DCCFGR_CCRI_BITS 9 +`define OR1200_DCCFGR_CBIRI_BITS 10 +`define OR1200_DCCFGR_CBPRI_BITS 11 +`define OR1200_DCCFGR_CBLRI_BITS 12 +`define OR1200_DCCFGR_CBFRI_BITS 13 +`define OR1200_DCCFGR_CBWBRI_BITS 14 +`define OR1200_DCCFGR_RES1_BITS 31:15 + +// DCCFGR values +`ifdef OR1200_NO_DC +`define OR1200_DCCFGR_NCW 3'h0 // Irrelevant +`define OR1200_DCCFGR_NCS 4'h0 // Irrelevant +`define OR1200_DCCFGR_CBS 1'b0 // Irrelevant +`define OR1200_DCCFGR_CWS 1'b0 // Irrelevant +`define OR1200_DCCFGR_CCRI 1'b1 // Irrelevant +`define OR1200_DCCFGR_CBIRI 1'b1 // Irrelevant +`define OR1200_DCCFGR_CBPRI 1'b0 // Irrelevant +`define OR1200_DCCFGR_CBLRI 1'b0 // Irrelevant +`define OR1200_DCCFGR_CBFRI 1'b1 // Irrelevant +`define OR1200_DCCFGR_CBWBRI 1'b0 // Irrelevant +`define OR1200_DCCFGR_RES1 17'h00000 +`else +`define OR1200_DCCFGR_NCW 3'h0 // 1 cache way +`define OR1200_DCCFGR_NCS (`OR1200_DCTAG) // Num cache sets +`define OR1200_DCCFGR_CBS (`OR1200_DCLS-4) // 16 byte cache block +`define OR1200_DCCFGR_CWS 1'b0 // Write-through strategy +`define OR1200_DCCFGR_CCRI 1'b1 // Cache control reg impl. +`define OR1200_DCCFGR_CBIRI 1'b1 // Cache block inv reg impl. +`define OR1200_DCCFGR_CBPRI 1'b0 // Cache block prefetch reg not impl. +`define OR1200_DCCFGR_CBLRI 1'b0 // Cache block lock reg not impl. +`define OR1200_DCCFGR_CBFRI 1'b1 // Cache block flush reg impl. +`define OR1200_DCCFGR_CBWBRI 1'b0 // Cache block WB reg not impl. +`define OR1200_DCCFGR_RES1 17'h00000 +`endif + +// ICCFGR fields +`define OR1200_ICCFGR_NCW_BITS 2:0 +`define OR1200_ICCFGR_NCS_BITS 6:3 +`define OR1200_ICCFGR_CBS_BITS 7 +`define OR1200_ICCFGR_CWS_BITS 8 +`define OR1200_ICCFGR_CCRI_BITS 9 +`define OR1200_ICCFGR_CBIRI_BITS 10 +`define OR1200_ICCFGR_CBPRI_BITS 11 +`define OR1200_ICCFGR_CBLRI_BITS 12 +`define OR1200_ICCFGR_CBFRI_BITS 13 +`define OR1200_ICCFGR_CBWBRI_BITS 14 +`define OR1200_ICCFGR_RES1_BITS 31:15 + +// ICCFGR values +`ifdef OR1200_NO_IC +`define OR1200_ICCFGR_NCW 3'h0 // Irrelevant +`define OR1200_ICCFGR_NCS 4'h0 // Irrelevant +`define OR1200_ICCFGR_CBS 1'b0 // Irrelevant +`define OR1200_ICCFGR_CWS 1'b0 // Irrelevant +`define OR1200_ICCFGR_CCRI 1'b0 // Irrelevant +`define OR1200_ICCFGR_CBIRI 1'b0 // Irrelevant +`define OR1200_ICCFGR_CBPRI 1'b0 // Irrelevant +`define OR1200_ICCFGR_CBLRI 1'b0 // Irrelevant +`define OR1200_ICCFGR_CBFRI 1'b0 // Irrelevant +`define OR1200_ICCFGR_CBWBRI 1'b0 // Irrelevant +`define OR1200_ICCFGR_RES1 17'h00000 +`else +`define OR1200_ICCFGR_NCW 3'h0 // 1 cache way +`define OR1200_ICCFGR_NCS (`OR1200_ICTAG) // Num cache sets +`define OR1200_ICCFGR_CBS (`OR1200_ICLS-4) // 16 byte cache block +`define OR1200_ICCFGR_CWS 1'b0 // Irrelevant +`define OR1200_ICCFGR_CCRI 1'b1 // Cache control reg impl. +`define OR1200_ICCFGR_CBIRI 1'b1 // Cache block inv reg impl. +`define OR1200_ICCFGR_CBPRI 1'b0 // Cache block prefetch reg not impl. +`define OR1200_ICCFGR_CBLRI 1'b0 // Cache block lock reg not impl. +`define OR1200_ICCFGR_CBFRI 1'b1 // Cache block flush reg impl. +`define OR1200_ICCFGR_CBWBRI 1'b0 // Irrelevant +`define OR1200_ICCFGR_RES1 17'h00000 +`endif + +// DCFGR fields +`define OR1200_DCFGR_NDP_BITS 2:0 +`define OR1200_DCFGR_WPCI_BITS 3 +`define OR1200_DCFGR_RES1_BITS 31:4 + +// DCFGR values +`ifdef OR1200_DU_HWBKPTS +`define OR1200_DCFGR_NDP 3'h`OR1200_DU_DVRDCR_PAIRS // # of DVR/DCR pairs +`ifdef OR1200_DU_DWCR0 +`define OR1200_DCFGR_WPCI 1'b1 +`else +`define OR1200_DCFGR_WPCI 1'b0 // WP counters not impl. +`endif +`else +`define OR1200_DCFGR_NDP 3'h0 // Zero DVR/DCR pairs +`define OR1200_DCFGR_WPCI 1'b0 // WP counters not impl. +`endif +`define OR1200_DCFGR_RES1 28'h0000000 + Index: minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/minsoc_defines.v =================================================================== --- minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/minsoc_defines.v (nonexistent) +++ minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/minsoc_defines.v (revision 136) @@ -0,0 +1,150 @@ +// +// Define FPGA manufacturer +// +//`define GENERIC_FPGA +//`define ALTERA_FPGA +`define XILINX_FPGA + +// +// Define Xilinx FPGA family +// +`ifdef XILINX_FPGA +//`define SPARTAN2 +//`define SPARTAN3 +`define SPARTAN3E +//`define SPARTAN3A +//`define VIRTEX +//`define VIRTEX2 +//`define VIRTEX4 +//`define VIRTEX5 + +// +// Define Altera FPGA family +// +`elsif ALTERA_FPGA +//`define ARRIA_GX +//`define ARRIA_II_GX +//`define CYCLONE_I +//`define CYCLONE_II +`define CYCLONE_III +//`define CYCLONE_III_LS +//`define CYCLONE_IV_E +//`define CYCLONE_IV_GS +//`define MAX_II +//`define MAX_V +//`define MAX3000A +//`define MAX7000AE +//`define MAX7000B +//`define MAX7000S +//`define STRATIX +//`define STRATIX_II +//`define STRATIX_II_GX +//`define STRATIX_III +`endif + +// +// Memory +// +`define MEMORY_ADR_WIDTH 12 //MEMORY_ADR_WIDTH IS NOT ALLOWED TO BE LESS THAN 12, + //memory is composed by blocks of address width 11 + //Address width of memory -> select memory depth, + //2 powers MEMORY_ADR_WIDTH defines the memory depth + //the memory data width is 32 bit, + //memory amount in Bytes = 4*memory depth + +// +// Memory type (uncomment something if ASIC or generic memory) +// +//`define GENERIC_MEMORY +//`define AVANT_ATP +//`define VIRAGE_SSP +//`define VIRTUALSILICON_SSP + + +// +// TAP selection +// +//`define GENERIC_TAP +`define FPGA_TAP + +// +// Clock Division selection +// +//`define NO_CLOCK_DIVISION +//`define GENERIC_CLOCK_DIVISION +`define FPGA_CLOCK_DIVISION // For Altera ALTPLL, only CYCLONE_III family has been tested. + +// +// Define division +// +`define CLOCK_DIVISOR 5 //in case of GENERIC_CLOCK_DIVISION the real value will be rounded + //down to an even value in FPGA case, check minsoc_clock_manager + //for allowed divisors. + //DO NOT USE CLOCK_DIVISOR = 1 COMMENT THE CLOCK DIVISION SELECTION + //INSTEAD. + +// +// Reset polarity +// +//`define NEGATIVE_RESET //rstn +`define POSITIVE_RESET //rst + +// +// Start-up circuit (only necessary later to load firmware automatically from SPI memory) +// +//`define START_UP + +// +// Connected modules +// +`define UART +`define ETHERNET + +// +// Ethernet reset +// +`define ETH_RESET 1'b0 +//`define ETH_RESET 1'b1 + +// +// Interrupts +// +`define APP_INT_RES1 1:0 +`define APP_INT_UART 2 +`define APP_INT_RES2 3 +`define APP_INT_ETH 4 +`define APP_INT_PS2 5 +`define APP_INT_RES3 19:6 + +// +// Address map +// +`define APP_ADDR_DEC_W 8 +`define APP_ADDR_SRAM `APP_ADDR_DEC_W'h00 +`define APP_ADDR_FLASH `APP_ADDR_DEC_W'h04 +`define APP_ADDR_DECP_W 4 +`define APP_ADDR_PERIP `APP_ADDR_DECP_W'h9 +`define APP_ADDR_SPI `APP_ADDR_DEC_W'h97 +`define APP_ADDR_ETH `APP_ADDR_DEC_W'h92 +`define APP_ADDR_AUDIO `APP_ADDR_DEC_W'h9d +`define APP_ADDR_UART `APP_ADDR_DEC_W'h90 +`define APP_ADDR_PS2 `APP_ADDR_DEC_W'h94 +`define APP_ADDR_RES1 `APP_ADDR_DEC_W'h9e +`define APP_ADDR_RES2 `APP_ADDR_DEC_W'h9f + +// +// Set-up GENERIC_TAP, GENERIC_MEMORY if GENERIC_FPGA was chosen +// and GENERIC_CLOCK_DIVISION if NO_CLOCK_DIVISION was not set +// +`ifdef GENERIC_FPGA + `undef FPGA_TAP + `undef FPGA_CLOCK_DIVISION + `undef XILINX_FPGA + `undef SPARTAN3E + + `define GENERIC_TAP + `define GENERIC_MEMORY + `ifndef NO_CLOCK_DIVISION + `define GENERIC_CLOCK_DIVISION + `endif +`endif
minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/minsoc_defines.v Property changes : Added: svn:executable ## -0,0 +1 ## +* \ No newline at end of property Index: minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/gcc-opt.mk =================================================================== --- minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/gcc-opt.mk (nonexistent) +++ minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/gcc-opt.mk (revision 136) @@ -0,0 +1 @@ +GCC_OPT=-mhard-mul -msoft-div -nostdlib Index: minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/spartan3e_starter_kit_eth.ucf =================================================================== --- minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/spartan3e_starter_kit_eth.ucf (nonexistent) +++ minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/spartan3e_starter_kit_eth.ucf (revision 136) @@ -0,0 +1,64 @@ +# +# Soldered 50MHz clock. +# +NET "clk" LOC = "C9"; + +# +# Use button "south" as reset. +# +NET "reset" LOC = "K17" | PULLDOWN ; + +# +# UART serial port (RS232 DCE) - connector DB9 female. +# +NET "uart_srx" LOC = "R7"; +NET "uart_stx" LOC = "M14" | DRIVE = 8 | SLEW = SLOW ; + +########################### +## +## ETH +## +NET "eth_txd(3)" LOC = "t5"; +NET "eth_txd(2)" LOC = "r5"; +NET "eth_txd(1)" LOC = "t15"; +NET "eth_txd(0)" LOC = "r11"; + +NET "eth_tx_en" LOC = "p15"; +NET "eth_tx_clk" LOC = "t7" | CLOCK_DEDICATED_ROUTE = FALSE; +NET "eth_tx_er" LOC = "r6"; + +NET "eth_rxd(3)" LOC = "v14"; +NET "eth_rxd(2)" LOC = "u11"; +NET "eth_rxd(1)" LOC = "t11"; +NET "eth_rxd(0)" LOC = "v8"; + +NET "eth_rx_er" LOC = "u14"; +NET "eth_rx_dv" LOC = "v2"; + +NET "eth_rx_clk" LOC = "v3" | CLOCK_DEDICATED_ROUTE = FALSE; + +NET "eth_mdio" LOC = "u5" | PULLUP; +NET "eth_crs" LOC = "u13"; +NET "eth_col" LOC = "u6"; +NET "eth_mdc" LOC = "p9"; + +NET "eth_trste" LOC = "p13"; #put it to a non connected FPGA pin (starter kit schematic BANK3) + +NET "eth_fds_mdint" LOC = "r13" | PULLUP; #put it to a non connected FPGA pin (starter kit schematic BANK3)(pullup not to generate interrupts) +########################### + +# +# JTAG signals - on J4 6-pin accessory header. +# + +#NET "jtag_tms" LOC = "D7" | PULLDOWN ; +#NET "jtag_tdi" LOC = "C7" | PULLDOWN ; +#NET "jtag_tdo" LOC = "F8" | SLEW = FAST | DRIVE = 8 ; +#NET "jtag_tck" LOC = "E8" | PULLDOWN ; + +#net "jtag_gnd" loc = "k2"; #put it to a non connected FPGA pin (starter kit schematic BANK3) +#net "jtag_vref" loc = "k7"; #put it to a non connected FPGA pin (starter kit schematic BANK3) + +# +# End of file. +#
minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/spartan3e_starter_kit_eth.ucf Property changes : Added: svn:executable ## -0,0 +1 ## +* \ No newline at end of property Index: minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/board.h =================================================================== --- minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/board.h (nonexistent) +++ minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/board.h (revision 136) @@ -0,0 +1,40 @@ +#ifndef _BOARD_H_ +#define _BOARD_H_ + +#define MC_ENABLED 0 + +#define IC_ENABLE 0 +#define IC_SIZE 8192 +#define DC_ENABLE 0 +#define DC_SIZE 8192 + + +#define IN_CLK 10000000 + + +#define STACK_SIZE 0x00180 + +#define UART_BAUD_RATE 19200 + +#define UART_BASE 0x90000000 +#define UART_IRQ 2 +#define ETH_BASE 0x92000000 +#define ETH_IRQ 4 +#define I2C_BASE 0x9D000000 +#define I2C_IRQ 3 +#define CAN_BASE 0x94000000 +#define CAN_IRQ 5 + +#define MC_BASE_ADDR 0x60000000 +#define SPI_BASE 0xa0000000 + +#define ETH_DATA_BASE 0xa8000000 /* Address for ETH_DATA */ + +#define ETH_MACADDR0 0x00 +#define ETH_MACADDR1 0x12 +#define ETH_MACADDR2 0x34 +#define ETH_MACADDR3 0x56 +#define ETH_MACADDR4 0x78 +#define ETH_MACADDR5 0x9a + +#endif
minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/board.h Property changes : Added: svn:executable ## -0,0 +1 ## +* \ No newline at end of property Index: minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/orp.ld =================================================================== --- minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/orp.ld (nonexistent) +++ minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/orp.ld (revision 136) @@ -0,0 +1,60 @@ +MEMORY + { + reset : ORIGIN = 0x00000000, LENGTH = 0x00000200 + vectors : ORIGIN = 0x00000200, LENGTH = 0x00001000 + ram : ORIGIN = 0x00001200, LENGTH = 0x00002E00 /*0x8000 total*/ + } + +SECTIONS +{ + .reset : + { + *(.reset) + } > reset + + + + .vectors : + { + _vec_start = .; + *(.vectors) + _vec_end = .; + } > vectors + + .text : + { + *(.text) + } > ram + + .rodata : + { + *(.rodata) + *(.rodata.*) + } > ram + + .icm : + { + _icm_start = .; + *(.icm) + _icm_end = .; + } > ram + + .data : + { + _dst_beg = .; + *(.data) + _dst_end = .; + } > ram + + .bss : + { + *(.bss) + } > ram + + .stack (NOLOAD) : + { + *(.stack) + _src_addr = .; + } > ram + +}
minsoc/branches/rc-1.0/backend/spartan3e_starter_kit_eth/orp.ld Property changes : Added: svn:executable ## -0,0 +1 ## +* \ No newline at end of property Index: minsoc/branches/rc-1.0/backend/ml509/ml509.ucf =================================================================== --- minsoc/branches/rc-1.0/backend/ml509/ml509.ucf (nonexistent) +++ minsoc/branches/rc-1.0/backend/ml509/ml509.ucf (revision 136) @@ -0,0 +1,45 @@ +NET clk LOC="AH15" | PERIOD=10ns | IOSTANDARD=LVCMOS33; # Bank 4, Vcco=3.3V, No DCI +NET reset LOC="E9" | PULLUP | IOSTANDARD=LVDCI_33; # Bank 20, Vcco=3.3V, DCI using 49.9 ohm resistors +NET uart_srx LOC="AG15" | IOSTANDARD=LVCMOS33; # Bank 4, Vcco=3.3V, No DCI +NET uart_stx LOC="AG20" | IOSTANDARD=LVCMOS33; # Bank 4, Vcco=3.3V, No DCI + +## #------------------------------------------------------------------------------ +## # IO Pad Location Constraints / Properties for Ethernet +## #------------------------------------------------------------------------------ + +#NET eth_col LOC = B32 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; +#NET eth_crs LOC = E34 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; +#NET eth_rx_dv LOC = E32 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; +#NET eth_rx_clk LOC = H17 | IOSTANDARD = LVCMOS25; +#NET eth_rxd<3> LOC = C32 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; +#NET eth_rxd<2> LOC = C33 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; +#NET eth_rxd<1> LOC = B33 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; +#NET eth_rxd<0> LOC = A33 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; + +#NET eth_rx_er LOC = E33 | IOSTANDARD = LVCMOS25 | IOBDELAY=NONE; +#NET eth_tx_clk LOC = K17 | IOSTANDARD = LVCMOS25; +#NET eth_trste LOC = J14 | IOSTANDARD = LVCMOS25 | PULLUP | TIG; # PHY_RESET pin on phy +#NET eth_txd<3> LOC = AH10 | IOSTANDARD = LVDCI_33; +#NET eth_txd<2> LOC = AH9 | IOSTANDARD = LVDCI_33; +#NET eth_txd<1> LOC = AE11 | IOSTANDARD = LVDCI_33; +#NET eth_txd<0> LOC = AF11 | IOSTANDARD = LVDCI_33; +#NET eth_tx_en LOC = AJ10 | IOSTANDARD = LVDCI_33; +#NET eth_tx_er LOC = AJ9 | IOSTANDARD = LVDCI_33; + +## PHY Serial Management Interface pins +#NET eth_mdc LOC = H19 | IOSTANDARD = LVCMOS25; +#NET eth_mdio LOC = H13 | IOSTANDARD = LVCMOS25; + +## # Timing Constraints (these are recommended in documentation and +## # are unaltered except for the TIG) +#NET "eth_rx_clk_BUFGP" TNM_NET = "RXCLK_GRP"; +#NET "eth_tx_clk_BUFGP" TNM_NET = "TXCLK_GRP"; +#TIMESPEC "TSTXOUT" = FROM "TXCLK_GRP" TO "PADS" 10 ns; +#TIMESPEC "TSRXIN" = FROM "PADS" TO "RXCLK_GRP" 6 ns; + +## # Timing ignores (to specify unconstrained paths) +#FIXME? NET "*clkgen0/wb_clk_o" TNM_NET = "sys_clk"; # Wishbone clock +#TIMESPEC "TS_PHYTX_OPB" = FROM "TXCLK_GRP" TO "sys_clk" TIG; +#TIMESPEC "TS_OPB_PHYTX" = FROM "sys_clk" TO "TXCLK_GRP" TIG; +#TIMESPEC "TS_PHYRX_OPB" = FROM "RXCLK_GRP" TO "sys_clk" TIG; +#TIMESPEC "TS_OPB_PHYRX" = FROM "sys_clk" TO "RXCLK_GRP" TIG;

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.