OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

Compare Revisions

  • This comparison shows the changes necessary to convert path
    /minsoc
    from Rev 104 to Rev 105
    Reverse comparison

Rev 104 → Rev 105

/trunk/backend/spartan3a_dsp_kit/configure
78,6 → 78,7
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE
rm TMPFILE
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat
fi
echo ""
echo ""
/trunk/backend/std/configure
78,6 → 78,7
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE
rm TMPFILE
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat
fi
echo ""
echo ""
/trunk/backend/altera_3c25_board/configure
3,10 → 3,8
#new boards have to udpate this
BOARD=altera_3c25_board #this has to have the name of the directory this file is in
DEVICE_PART=EP3C25Q240C8
CONSTRAINT_FILE='altera_3c25_board.ucf'
FAMILY_PART="Cyclone III"
CONSTRAINT_FILE='altera_3c25_board.ucf'
PROJECT_FILE=minsoc_top.qsf
#SW_VERSION=`quartus_map -v | grep Version`
#~new boards update
 
#system workings
17,6 → 15,8
SYNSUPPORT_DIR=$SYN_DIR/buildSupport
MAKEFILE_DIR=$SYN_DIR/altera
 
PROJECT_FILE=minsoc_top.qsf
 
SYN_FILES=(adbg_top.prj jtag_top.prj or1200_top.prj uart_top.prj minsoc_top.prj altera_virtual_jtag.prj)
MAKEFILE=Makefile
 
87,6 → 87,7
 
echo "Copying Makefile from $MAKEFILE_DIR to synthesis directory, $SYN_DIR..."
cp $MAKEFILE_DIR/$MAKEFILE $SYN_DIR/$MAKEFILE
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat
echo ""
 
echo "Copying board specific SoC files from $BOARD_DIR to $BACKEND_DIR directory."
/trunk/backend/spartan3e_starter_kit/configure
96,6 → 96,7
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE
rm TMPFILE
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat
fi
echo ""
echo ""
/trunk/backend/spartan3e_starter_kit_eth/configure
97,6 → 97,7
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE
rm TMPFILE
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat
fi
echo ""
echo ""
/trunk/syn/setup.bat File deleted \ No newline at end of file
/trunk/syn/xilinx/setup.bat
0,0 → 1,12
@echo off
set /p xilinx_settings=Input the Xilinx "settings32|64.bat" file along with its absolute path:
if EXIST %xilinx_settings% (
%xilinx_settings%
make all
echo Finished...
set /p exit=Press ENTER to close this window...
make clean
) ELSE (
echo %xilinx_settings% could not be found.
set /p exit=Press ENTER to close this window...
)

powered by: WebSVN 2.1.0

© copyright 1999-2021 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.