URL
https://opencores.org/ocsvn/minsoc/minsoc/trunk
Subversion Repositories minsoc
Compare Revisions
- This comparison shows the changes necessary to convert path
/minsoc
- from Rev 105 to Rev 104
- ↔ Reverse comparison
Rev 105 → Rev 104
/trunk/syn/xilinx/setup.bat
File deleted
\ No newline at end of file
/trunk/syn/setup.bat
0,0 → 1,12
@echo off |
set /p xilinx_settings=Input the Xilinx "settings32|64.bat" file along with its absolute path: |
if EXIST %xilinx_settings% ( |
%xilinx_settings% |
make all |
echo Finished... |
set /p exit=Press ENTER to close this window... |
make clean |
) ELSE ( |
echo %xilinx_settings% could not be found. |
set /p exit=Press ENTER to close this window... |
) |
/trunk/backend/altera_3c25_board/configure
3,8 → 3,10
#new boards have to udpate this |
BOARD=altera_3c25_board #this has to have the name of the directory this file is in |
DEVICE_PART=EP3C25Q240C8 |
FAMILY_PART="Cyclone III" |
CONSTRAINT_FILE='altera_3c25_board.ucf' |
FAMILY_PART="Cyclone III" |
PROJECT_FILE=minsoc_top.qsf |
#SW_VERSION=`quartus_map -v | grep Version` |
#~new boards update |
|
#system workings |
15,8 → 17,6
SYNSUPPORT_DIR=$SYN_DIR/buildSupport |
MAKEFILE_DIR=$SYN_DIR/altera |
|
PROJECT_FILE=minsoc_top.qsf |
|
SYN_FILES=(adbg_top.prj jtag_top.prj or1200_top.prj uart_top.prj minsoc_top.prj altera_virtual_jtag.prj) |
MAKEFILE=Makefile |
|
87,7 → 87,6
|
echo "Copying Makefile from $MAKEFILE_DIR to synthesis directory, $SYN_DIR..." |
cp $MAKEFILE_DIR/$MAKEFILE $SYN_DIR/$MAKEFILE |
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat |
echo "" |
|
echo "Copying board specific SoC files from $BOARD_DIR to $BACKEND_DIR directory." |
/trunk/backend/spartan3a_dsp_kit/configure
78,7 → 78,6
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE |
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE |
rm TMPFILE |
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat |
fi |
echo "" |
echo "" |
/trunk/backend/std/configure
78,7 → 78,6
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE |
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE |
rm TMPFILE |
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat |
fi |
echo "" |
echo "" |
/trunk/backend/spartan3e_starter_kit/configure
96,7 → 96,6
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE |
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE |
rm TMPFILE |
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat |
fi |
echo "" |
echo "" |
/trunk/backend/spartan3e_starter_kit_eth/configure
97,7 → 97,6
sed "s/$FIND_PART/$DEVICE_PART/g" $MAKEFILE_DIR/$MAKEFILE > TMPFILE |
sed "s/$FIND_CONSTRAINT/$CONSTRAINT_FILE/g" TMPFILE > TMPFILE2 && mv TMPFILE2 $SYN_DIR/$MAKEFILE |
rm TMPFILE |
cp $MAKEFILE_DIR/setup.bat $SYN_DIR/setup.bat |
fi |
echo "" |
echo "" |