OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

Compare Revisions

  • This comparison shows the changes necessary to convert path
    /minsoc/trunk
    from Rev 11 to Rev 12
    Reverse comparison

Rev 11 → Rev 12

/rtl/verilog/minsoc_startup/spi_top.v
165,7 → 165,7
`ifdef SPI_CTRL_TX_NEGEDGE
assign tx_negedge = 1'b1;
`else
assign tx_negedge = 1'b1;
assign tx_negedge = 1'b0;
`endif
 
assign ctrl = {ass,1'b0,lsb,tx_negedge,rx_negedge,go,1'b0,1'b0,char_len};
/doc/minsoc.pdf Cannot display: file marked as a binary type. svn:mime-type = application/octet-stream
/doc/minsoc.odt Cannot display: file marked as a binary type. svn:mime-type = application/octet-stream
/backend/spartan3e_starter_kit.ucf
1,50 → 1,50
#
# Soldered 50MHz clock.
#
NET "clk" LOC = "C9" | IOSTANDARD = LVTTL;
NET "clk" LOC = "C9";
 
#
# Use button "south" as reset.
#
NET "reset" LOC = "K17" | IOSTANDARD = LVTTL | PULLDOWN ;
NET "reset" LOC = "K17" | PULLDOWN ;
 
#
# UART serial port (RS232 DCE) - connector DB9 female.
#
NET "uart_srx" LOC = "R7" | IOSTANDARD = LVTTL ;
NET "uart_stx" LOC = "M14" | IOSTANDARD = LVTTL | DRIVE = 8 | SLEW = SLOW ;
#NET "uart_srx" LOC = "R7" | IOSTANDARD = LVTTL ;
#NET "uart_stx" LOC = "M14" | IOSTANDARD = LVTTL | DRIVE = 8 | SLEW = SLOW ;
 
###########################
##
## ETH
##
#NET "eth_txd(3)" LOC = "t5";
#NET "eth_txd(2)" LOC = "r5";
#NET "eth_txd(1)" LOC = "t15";
#NET "eth_txd(0)" LOC = "r11";
#
#NET "eth_tx_en" LOC = "p15";
#NET "eth_tx_clk" LOC = "t7";
#NET "eth_tx_er" LOC = "r6";
#
#NET "eth_rxd(3)" LOC = "v14";
#NET "eth_rxd(2)" LOC = "u11";
#NET "eth_rxd(1)" LOC = "t11";
#NET "eth_rxd(0)" LOC = "v8";
#
#NET "eth_rx_er" LOC = "u14";
#NET "eth_rx_dv" LOC = "v2";
#
#NET "eth_rx_clk" LOC = "v3";
#
#NET "eth_mdio" LOC = "u5" | PULLUP;
#NET "eth_crs" LOC = "u13";
#NET "eth_col" LOC = "u6";
#NET "eth_mdc" LOC = "p9";
#
#NET "eth_trste" LOC = "n2"; #put it to a non connected FPGA pin (starter kit schematic BANK3)
#
#NET "eth_fds_mdint" LOC = "n1" | PULLUP; #put it to a non connected FPGA pin (starter kit schematic BANK3)(pullup not to generate interrupts)
NET "eth_txd(3)" LOC = "t5";
NET "eth_txd(2)" LOC = "r5";
NET "eth_txd(1)" LOC = "t15";
NET "eth_txd(0)" LOC = "r11";
 
NET "eth_tx_en" LOC = "p15";
NET "eth_tx_clk" LOC = "t7" | CLOCK_DEDICATED_ROUTE = FALSE;
NET "eth_tx_er" LOC = "r6";
 
NET "eth_rxd(3)" LOC = "v14";
NET "eth_rxd(2)" LOC = "u11";
NET "eth_rxd(1)" LOC = "t11";
NET "eth_rxd(0)" LOC = "v8";
 
NET "eth_rx_er" LOC = "u14";
NET "eth_rx_dv" LOC = "v2";
 
NET "eth_rx_clk" LOC = "v3" | CLOCK_DEDICATED_ROUTE = FALSE;
 
NET "eth_mdio" LOC = "u5" | PULLUP;
NET "eth_crs" LOC = "u13";
NET "eth_col" LOC = "u6";
NET "eth_mdc" LOC = "p9";
 
NET "eth_trste" LOC = "p13"; #put it to a non connected FPGA pin (starter kit schematic BANK3)
 
NET "eth_fds_mdint" LOC = "r13" | PULLUP; #put it to a non connected FPGA pin (starter kit schematic BANK3)(pullup not to generate interrupts)
###########################
 
#

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.