OpenCores
URL https://opencores.org/ocsvn/zipcpu/zipcpu/trunk

Subversion Repositories zipcpu

Compare Revisions

  • This comparison shows the changes necessary to convert path
    /
    from Rev 194 to Rev 195
    Reverse comparison

Rev 194 → Rev 195

/zipcpu/trunk/rtl/aux/busdelay.v
1,4 → 1,4
///////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
//
// Filename: busdelay.v
//
16,14 → 16,28
// *must* know on the first clock whether or not the bus will stall.
//
//
// After a period of time, I started a new design where the timing
// associated with this original bus clock just wasn't ... fast enough.
// I needed to delay the stall line as well. A new busdelay was then
// written and debugged whcih delays the stall line. (I know, you aren't
// supposed to delay the stall line--but what if you *have* to in order
// to meet timing?) This new logic has been merged in with the old,
// and the DELAY_STALL line can be set to non-zero to use it instead
// of the original logic. Don't use it if you don't need it: it will
// consume resources and slow your bus down more, but if you do need
// it--don't be afraid to use it.
//
// Both versions of the bus delay will maintain a single access per
// clock when pipelined, they only delay the time between the strobe
// going high and the actual command being accomplished.
//
//
// Creator: Dan Gisselquist, Ph.D.
// Gisselquist Technology, LLC
//
///////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
//
// Copyright (C) 2015, Gisselquist Technology, LLC
// Copyright (C) 2015-2016, Gisselquist Technology, LLC
//
// This program is free software (firmware): you can redistribute it and/or
// modify it under the terms of the GNU General Public License as published
39,7 → 53,7
// http://www.gnu.org/licenses/gpl.html
//
//
///////////////////////////////////////////////////////////////////////////
////////////////////////////////////////////////////////////////////////////////
//
module busdelay(i_clk,
// The input bus
48,7 → 62,7
// The delayed bus
o_dly_cyc, o_dly_stb, o_dly_we, o_dly_addr, o_dly_data,
i_dly_ack, i_dly_stall, i_dly_data, i_dly_err);
parameter AW=32, DW=32;
parameter AW=32, DW=32, DELAY_STALL = 0;
input i_clk;
// Input/master bus
input i_wb_cyc, i_wb_stb, i_wb_we;
67,35 → 81,100
input [(DW-1):0] i_dly_data;
input i_dly_err;
 
initial o_dly_cyc = 1'b0;
initial o_dly_stb = 1'b0;
generate
if (DELAY_STALL != 0)
begin
reg r_stb, r_we, r_rtn_stall, r_rtn_err;
reg [(DW-1):0] r_data;
reg [(AW-1):0] r_addr;
 
always @(posedge i_clk)
o_dly_cyc <= i_wb_cyc;
// Add the i_wb_cyc criteria here, so we can simplify the o_wb_stall
// criteria below, which would otherwise *and* these two.
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_stb <= ((i_wb_cyc)&&(i_wb_stb));
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_we <= i_wb_we;
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_addr<= i_wb_addr;
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_data <= i_wb_data;
always @(posedge i_clk)
o_wb_ack <= (i_dly_ack)&&(o_dly_cyc)&&(i_wb_cyc);
always @(posedge i_clk)
o_wb_data <= i_dly_data;
initial o_dly_cyc = 1'b0;
initial r_rtn_stall= 1'b0;
initial r_stb = 1'b0;
always @(posedge i_clk)
begin
o_dly_cyc <= (i_wb_cyc);
if (!i_dly_stall)
begin
r_we <= i_wb_we;
r_addr <= i_wb_addr;
r_data <= i_wb_data;
 
// Our only non-delayed line, yet still really delayed. Perhaps
// there's a way to register this?
// o_wb_stall <= (i_wb_cyc)&&(i_wb_stb) ... or some such?
// assign o_wb_stall=((i_wb_cyc)&&(i_dly_stall)&&(o_dly_stb));//&&o_cyc
assign o_wb_stall = ((i_dly_stall)&&(o_dly_stb));//&&o_cyc
assign o_wb_err = i_dly_err;
if (r_stb)
begin
o_dly_we <= r_we;
o_dly_addr <= r_addr;
o_dly_data <= r_data;
o_dly_stb <= 1'b1;
r_rtn_stall <= 1'b0;
r_stb <= 1'b0;
end else begin
o_dly_we <= i_wb_we;
o_dly_addr <= i_wb_addr;
o_dly_data <= i_wb_data;
o_dly_stb <= i_wb_stb;
r_stb <= 1'b0;
r_rtn_stall <= 1'b0;
end
end else if ((!r_stb)&&(!o_wb_stall))
begin
r_we <= i_wb_we;
r_addr <= i_wb_addr;
r_data <= i_wb_data;
r_stb <= i_wb_stb;
 
r_rtn_stall <= i_wb_stb;
end
 
if (!i_wb_cyc)
begin
o_dly_stb <= 1'b0;
r_stb <= 1'b0;
r_rtn_stall <= 1'b0;
end
 
o_wb_ack <= (i_dly_ack)&&(i_wb_cyc)&&(o_dly_cyc);
o_wb_data <= i_dly_data;
r_rtn_err <= (i_dly_err)&&(i_wb_cyc)&&(o_dly_cyc);
end
 
assign o_wb_stall = r_rtn_stall;
assign o_wb_err = r_rtn_err;
 
end else begin
 
initial o_dly_cyc = 1'b0;
initial o_dly_stb = 1'b0;
 
always @(posedge i_clk)
o_dly_cyc <= i_wb_cyc;
// Add the i_wb_cyc criteria here, so we can simplify the
// o_wb_stall criteria below, which would otherwise *and*
// these two.
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_stb <= ((i_wb_cyc)&&(i_wb_stb));
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_we <= i_wb_we;
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_addr<= i_wb_addr;
always @(posedge i_clk)
if (~o_wb_stall)
o_dly_data <= i_wb_data;
always @(posedge i_clk)
o_wb_ack <= (i_dly_ack)&&(o_dly_cyc)&&(i_wb_cyc);
always @(posedge i_clk)
o_wb_data <= i_dly_data;
 
// Our only non-delayed line, yet still really delayed. Perhaps
// there's a way to register this?
// o_wb_stall <= (i_wb_cyc)&&(i_wb_stb) ... or some such?
// assign o_wb_stall=((i_wb_cyc)&&(i_dly_stall)&&(o_dly_stb));//&&o_cyc
assign o_wb_stall = ((i_dly_stall)&&(o_dly_stb));//&&o_cyc
assign o_wb_err = i_dly_err;
end endgenerate
 
endmodule

powered by: WebSVN 2.1.0

© copyright 1999-2022 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.