| Line 13... |
Line 13... |
ARCHITECTURE behavior OF testUart_control IS
|
ARCHITECTURE behavior OF testUart_control IS
|
|
|
-- Component Declaration for the Unit Under Test (UUT)
|
-- Component Declaration for the Unit Under Test (UUT)
|
|
|
COMPONENT uart_control
|
COMPONENT uart_control
|
Port ( rst : in STD_LOGIC; -- Global reset
|
Port ( rst : in std_logic; -- Global reset
|
clk : in STD_LOGIC; -- Global clock
|
clk : in std_logic; -- Global clock
|
WE : in STD_LOGIC; -- Write enable
|
WE : in std_logic; -- Write enable
|
reg_addr : in STD_LOGIC_VECTOR (1 downto 0); -- Register address
|
reg_addr : in std_logic_vector (1 downto 0); -- Register address
|
start : in std_logic; -- Start (Strobe)
|
start : in std_logic; -- Start (Strobe)
|
done : out std_logic; -- Done (ACK)
|
done : out std_logic; -- Done (ACK)
|
DAT_I : in STD_LOGIC_VECTOR ((nBitsLarge-1) downto 0); -- Data Input (Wishbone)
|
DAT_I : in std_logic_vector ((nBitsLarge-1) downto 0); -- Data Input (Wishbone)
|
DAT_O : out STD_LOGIC_VECTOR ((nBitsLarge-1) downto 0); -- Data output (Wishbone)
|
DAT_O : out std_logic_vector ((nBitsLarge-1) downto 0); -- Data output (Wishbone)
|
baud_wait : out STD_LOGIC_VECTOR ((nBitsLarge-1) downto 0); -- Signal to control the baud rate frequency
|
baud_wait : out std_logic_vector ((nBitsLarge-1) downto 0); -- Signal to control the baud rate frequency
|
data_byte_tx : out std_logic_vector((nBits-1) downto 0); -- 1 Byte to be send to serial_transmitter
|
data_byte_tx : out std_logic_vector((nBits-1) downto 0); -- 1 Byte to be send to serial_transmitter
|
data_byte_rx : in std_logic_vector((nBits-1) downto 0); -- 1 Byte to be received by serial_receiver
|
data_byte_rx : in std_logic_vector((nBits-1) downto 0); -- 1 Byte to be received by serial_receiver
|
tx_data_sent : in STD_LOGIC; -- Signal comming from serial_transmitter
|
tx_data_sent : in std_logic; -- Signal comming from serial_transmitter
|
|
tx_start : out std_logic; -- Signal to start sending serial data...
|
rst_comm_blocks : out std_logic; -- Reset Communication blocks
|
rst_comm_blocks : out std_logic; -- Reset Communication blocks
|
rx_data_ready : in STD_LOGIC); -- Signal comming from serial_receiver
|
rx_data_ready : in std_logic);
|
END COMPONENT;
|
END COMPONENT;
|
|
|
|
|
--Inputs
|
--Inputs
|
signal rst : std_logic := '0';
|
signal rst : std_logic := '0';
|
| Line 43... |
Line 44... |
signal tx_data_sent : std_logic := '0';
|
signal tx_data_sent : std_logic := '0';
|
signal rx_data_ready : std_logic := '0';
|
signal rx_data_ready : std_logic := '0';
|
|
|
--Outputs
|
--Outputs
|
signal done : std_logic;
|
signal done : std_logic;
|
|
signal tx_start : std_logic;
|
signal rst_comm_blocks : std_logic;
|
signal rst_comm_blocks : std_logic;
|
signal DAT_O : std_logic_vector((nBitsLarge-1) downto 0);
|
signal DAT_O : std_logic_vector((nBitsLarge-1) downto 0);
|
signal baud_wait : std_logic_vector((nBitsLarge-1) downto 0);
|
signal baud_wait : std_logic_vector((nBitsLarge-1) downto 0);
|
signal data_byte_tx : std_logic_vector((nBits-1) downto 0);
|
signal data_byte_tx : std_logic_vector((nBits-1) downto 0);
|
|
|
| Line 68... |
Line 70... |
baud_wait => baud_wait,
|
baud_wait => baud_wait,
|
data_byte_tx => data_byte_tx,
|
data_byte_tx => data_byte_tx,
|
data_byte_rx => data_byte_rx,
|
data_byte_rx => data_byte_rx,
|
tx_data_sent => tx_data_sent,
|
tx_data_sent => tx_data_sent,
|
rst_comm_blocks => rst_comm_blocks,
|
rst_comm_blocks => rst_comm_blocks,
|
|
tx_start => tx_start,
|
rx_data_ready => rx_data_ready
|
rx_data_ready => rx_data_ready
|
);
|
);
|
|
|
-- Clock process definitions
|
-- Clock process definitions
|
clk_process :process
|
clk_process :process
|
| Line 117... |
Line 120... |
-- Ask to send some data...(0x55)
|
-- Ask to send some data...(0x55)
|
reg_addr <= "10";
|
reg_addr <= "10";
|
WE <= '1';
|
WE <= '1';
|
start <= '1';
|
start <= '1';
|
DAT_I <= x"00000055";
|
DAT_I <= x"00000055";
|
wait for clk_period*10;
|
wait for clk_period*10; -- No point to use wait until because we're not connected to the comm block yet
|
|
|
-- Stop Simulation
|
-- Stop Simulation
|
assert false report "NONE. End of simulation." severity failure;
|
assert false report "NONE. End of simulation." severity failure;
|
end process;
|
end process;
|
|
|
