OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [trunk/] [backend/] [spartan3e_starter_kit/] [spartan3e_starter_kit.ucf] - Diff between revs 13 and 64

Go to most recent revision | Show entire file | Details | Blame | View Log

Rev 13 Rev 64
?rev1line?
?rev2line?
 
#
 
# Soldered 50MHz clock.
 
#
 
NET "clk" LOC = "C9";
 
 
 
#
 
# Use button "south" as reset.
 
#
 
NET "reset" LOC = "K17" | PULLDOWN ;
 
 
 
#
 
# UART serial port (RS232 DCE) - connector DB9 female.
 
#
 
NET "uart_srx" LOC = "R7";
 
NET "uart_stx" LOC = "M14" | DRIVE = 8 | SLEW = SLOW ;
 
 
 
###########################
 
##
 
## ETH
 
##
 
#NET "eth_txd(3)" LOC = "t5";
 
#NET "eth_txd(2)" LOC = "r5";
 
#NET "eth_txd(1)" LOC = "t15";
 
#NET "eth_txd(0)" LOC = "r11";
 
#
 
#NET "eth_tx_en" LOC = "p15";
 
#NET "eth_tx_clk" LOC = "t7" | CLOCK_DEDICATED_ROUTE = FALSE;
 
#NET "eth_tx_er" LOC = "r6";
 
#
 
#NET "eth_rxd(3)" LOC = "v14";
 
#NET "eth_rxd(2)" LOC = "u11";
 
#NET "eth_rxd(1)" LOC = "t11";
 
#NET "eth_rxd(0)" LOC = "v8";
 
#
 
#NET "eth_rx_er" LOC = "u14";
 
#NET "eth_rx_dv" LOC = "v2";
 
#
 
#NET "eth_rx_clk" LOC = "v3" | CLOCK_DEDICATED_ROUTE = FALSE;
 
#
 
#NET "eth_mdio" LOC = "u5" | PULLUP;
 
#NET "eth_crs" LOC = "u13";
 
#NET "eth_col" LOC = "u6";
 
#NET "eth_mdc" LOC = "p9";
 
#
 
#NET "eth_trste" LOC = "p13";                   #put it to a non connected FPGA pin (starter kit schematic BANK3)
 
#
 
#NET "eth_fds_mdint" LOC = "r13" | PULLUP;      #put it to a non connected FPGA pin (starter kit schematic BANK3)(pullup not to generate interrupts)
 
###########################
 
 
 
#
 
# JTAG signals - on J4 6-pin accessory header.
 
#
 
 
 
#NET "jtag_tms"  LOC = "D7" | PULLDOWN ;
 
#NET "jtag_tdi"  LOC = "C7" | PULLDOWN ;
 
#NET "jtag_tdo"  LOC = "F8" | SLEW = FAST | DRIVE = 8 ;
 
#NET "jtag_tck"  LOC = "E8" | PULLDOWN ;
 
 
 
#net "jtag_gnd" loc = "k2";                     #put it to a non connected FPGA pin (starter kit schematic BANK3)
 
#net "jtag_vref" loc = "k7";                    #put it to a non connected FPGA pin (starter kit schematic BANK3)
 
 
 
#
 
# End of file.
 
#

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.