OpenCores
URL https://opencores.org/ocsvn/or1k/or1k/trunk

Subversion Repositories or1k

[/] [or1k/] [trunk/] [rc203soc/] [sw/] [uClinux/] [arch/] [armnommu/] [drivers/] [block/] [Config.in] - Rev 1622

Go to most recent revision | Compare with Previous | Blame | View Log

#
# Block device driver configuration
#
mainmenu_option next_comment
comment 'Floppy, IDE, and other block devices'

tristate 'Normal floppy disk support' CONFIG_BLK_DEV_FD
bool 'Enhanced IDE disk/cdrom/tape support' CONFIG_BLK_DEV_IDE
comment 'Please see Documentation/ide.txt for help/info on IDE drives'
if [ "$CONFIG_BLK_DEV_IDE" = "n" ]; then
  bool 'Old harddisk (IDE) driver' CONFIG_BLK_DEV_HD_ONLY
else
  bool '   Use old disk-only driver on primary interface' CONFIG_BLK_DEV_HD_IDE
  bool '   Include IDE/ATAPI CDROM support' CONFIG_BLK_DEV_IDECD
  bool '   Include IDE/ATAPI TAPE support' CONFIG_BLK_DEV_IDETAPE
  bool '   Include IDE/ATAPI FLOPPY support (new)' CONFIG_BLK_DEV_IDEFLOPPY
  bool '   SCSI emulation support' CONFIG_BLK_DEV_IDESCSI
  bool '   Support removable IDE interfaces (PCMCIA)' CONFIG_BLK_DEV_IDE_PCMCIA
  bool '   Support expansion card IDE interfaces' CONFIG_BLK_DEV_IDE_CARDS
  if [ "$CONFIG_BLK_DEV_IDE_CARDS" = "y" ]; then
    tristate '    ICS IDE interface support' CONFIG_BLK_DEV_IDE_ICSIDE
    tristate '    RapIDE interface support' CONFIG_BLK_DEV_IDE_RAPIDE
  fi
fi

tristate 'MFM harddisk support' CONFIG_BLK_DEV_XD

comment 'Additional Block Devices'

tristate 'Loopback device support' CONFIG_BLK_DEV_LOOP
bool 'Multiple devices driver support' CONFIG_BLK_DEV_MD
if [ "$CONFIG_BLK_DEV_MD" = "y" ]; then
  tristate '   Linear (append) mode' CONFIG_MD_LINEAR
  tristate '   RAID-0 (striping) mode' CONFIG_MD_STRIPED
  tristate '   RAID-1 (mirroring) mode' CONFIG_MD_MIRRORING
  tristate '   RAID-4/RAID-5 mode' CONFIG_MD_RAID5
fi
tristate 'RAM disk support' CONFIG_BLK_DEV_RAM
if [ "$CONFIG_BLK_DEV_RAM" = "y" ]; then
  bool '   Initial RAM disk (initrd) support' CONFIG_BLK_DEV_INITRD
fi
bool 'ADFS partition support' CONFIG_BLK_DEV_PART
#if [ "$CONFIG_BLK_DEV_PART" = "y" -a "$CONFIG_EXPERIMENTAL" = "y" ]; then
#  bool 'ADFS image file support (EXPERIMENTAL)' CONFIG_BLK_DEV_IMG
#fi

if [ "$CONFIG_BLK_DEV_HD_IDE" = "y" -o "$CONFIG_BLK_DEV_HD_ONLY" = "y" ]; then
  define_bool CONFIG_BLK_DEV_HD y
else
  define_bool CONFIG_BLK_DEV_HD n
fi

endmenu

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.