URL
https://opencores.org/ocsvn/System09/System09/trunk
Subversion Repositories System09
[/] [System09/] [rev_86/] [src/] [fmt/] [fmt_cf8.asm] - Rev 143
Go to most recent revision | Compare with Previous | Blame | View Log
*
** FLEX 9 COMPACT FLASH FORMAT PROGRAM
*
* FOR B5-X300 and CF with 8 Bit Transfer interface
*
*
CFLAG EQU $01 CARRY FLAG
VFLAG EQU $02 OVERFLOW FLAG
ZFLAG EQU $04 ZERO FLAG
NFLAG EQU $08 NEGATIVE FLAG
IFLAG EQU $10 IRQ MASK CC
HFLAG EQU $20 HALF CARRY
FFLAG EQU $40 FIRQ MASK CC
EFLAG EQU $80 ENTIRE FLAG
*
MAPPAG EQU $00 PAGE $0000 DAT ADDRESS
*
* Serial Port
*
ACIAS EQU $E000
ACIAC1 EQU ACIAS
ACIAD1 EQU ACIAS+1
DELCON EQU 1250 Delay (Processor clock in MHz * 50)
*
* XMODEM Control characters
*
SOH EQU $01
EOT EQU $04
ACK EQU $06
NAK EQU $15
CAN EQU $18
*
* Some dummy Constants
*
RMAXTRK EQU 64
RMAXSEC EQU 255
RTOTSEC EQU RMAXTRK*RMAXSEC-RMAXSEC
*
* Start
*
ORG $0100
START LBSR UFSUB
JMP [$F800] Jump to monitor on Completion.
*
*
* RAM SPACE
*
DRVNUM FCB 0
TRACK FCB 0
SECTOR FCB 0
CHKSUM FCB 0
BLKNUM FCB 0 Xmodem block number
BYTCNT FCB 0 Xmodem byte count
XSTATE FDB 0 Xmodem State Vector
DELCNT FCB $00,$00,$00 Xmodem Poll timer
MAXTRK FCB 0
MAXSEC FCB 0
ORG $0200
*
* SECTOR BUFFER
*
BUFFER RMB 256
*
*
* recieve char from remote drive.
* timeout if no response for approx 1s.
* Entry: no parameters
* Exit: (A) = recieved char, (C)=1 if valid char, (C)=0 if timeout.
*
RCHAR PSHS X,Y
*
LDX #1000 1000x inner loop
RCHAR1 LDY #DELCON delay constant for inner loop (approx 1ms).
RCHAR2 LDA ACIAC1 test for recieved char
ASRA
BCS RCHAR3 get character
LEAY -1,Y else, continue to count delay
BNE RCHAR2
LEAX -1,X
BNE RCHAR1
PULS X,Y,PC return with error if timed out
*
RCHAR3 LDA ACIAD1 return data (carry bit still set)
PULS X,Y,PC
*
*
* transmit char to remote drive.
* timeout if no response for approx 1s. (allows for use of hardware flow control)
* Entry: (A) = char to transmit
* Exit: (A) = recieved char, (C)=1 if valid char, (C)=0 if timeout.
*
SCHAR PSHS X,Y
PSHS A
*
LDX #1000 1000x inner loop
SCHAR1 LDY #DELCON delay constant for inner loop (approx 1ms).
SCHAR2 LDA ACIAC1 test for space in transmit FIFO
ASRA
ASRA
BCS SCHAR3 send character
LEAY -1,Y else, continue to count delay
BNE SCHAR2
LEAX -1,X
BNE SCHAR1
PULS A
PULS X,Y,PC return with error if timed out
*
SCHAR3 PULS A
STA ACIAD1 send data (carry bit still set)
PULS X,Y,PC
*
* Print Data
*
PDATA0 BSR SCHAR
PDATA1 LDA ,X+
CMPA #$04
BNE PDATA0
RTS
*
** 'UF' Format RAMdisc to FLEX standard.
*
DISFOS FCB $0A,$0D
FCC 'Formating RAMdisk... '
FCB $0A,$0D
FCC 'Drive Number ?'
FCB 4
MESS6 FCB $0A,$0D,4
FCC 'Ramdisk not allocated! '
FCB 4
UFMSG1 FCB $0A,$0D
FCC 'Format Complete'
FCB 4
*
UFSUB JSR INITDR
LDX #DISFOS
JSR PDATA1
UFSUB1 LBSR RCHAR
BCC UFSUB1
LBSR SCHAR
CMPA #'0'
LBLO UFEXIT
CMPA #'3'
LBHI UFEXIT
SUBA #'0'
TFR A,B
STB DRVNUM
LDX #DRVNUM-3
JSR DRVSEL
*
* set up free chain
*
LDX #BUFFER clear out buffer
CLRA
CLRB
DFL1 STA 0,X+
DECB
BNE DFL1
*
CLR TRACK
LDA #1
STA SECTOR
DFL2 LDX #BUFFER
LDA TRACK
STA 0,X
LDA SECTOR
INCA
CMPA #RMAXSEC+1 last sector on track?
BNE DFL3
INC 0,X
LDA #1
DFL3 STA 1,X
LDA TRACK
LDB SECTOR
JSR WRITSC
INC SECTOR
LDA SECTOR
CMPA #RMAXSEC+1
BNE DFL2
LDA #1
STA SECTOR
INC TRACK
LDA TRACK
CMPA #RMAXTRK
BNE DFL2
* break free chain at last track/sector
LDX #BUFFER
LDA #RMAXTRK-1
LDB #RMAXSEC
JSR READSC
LDX #BUFFER
CLR 0,X
CLR 1,X
LDA #RMAXTRK-1
LDB #RMAXSEC
JSR WRITSC
* set up sector structure, SIR, directory etc
LDX #BUFFER
CLRA
LDB #RMAXSEC
JSR READSC
LDX #BUFFER
CLR 0,X break end of directory chain
CLR 1,X
CLRA
LDB #RMAXSEC
JSR WRITSC
*
LDX #BUFFER
CLRA
LDB #3 set up SIR
JSR READSC
LDX #BUFFER
CLR 0,X break forward link
CLR 1,X
LDD #$5241 set volume name (RAMDISK )
STD 16,X
LDD #$4D44
STD 18,X
LDD #$4953
STD 20,X
LDD #$4B20
STD 22,X
LDD #1 volume number
STD 27,X
LDD #$0101 first trk/sec 01-01
STD 29,X
LDA #RMAXTRK-1
LDB #RMAXSEC
STD 31,X
STD 38,X
LDD #RTOTSEC total DATA sectors (2912-14)
STD 33,X
*
LDA #01 month set default creation date (SYS09's birthday!)
STA 35,X
LDA #07 day
STA 36,X
LDA #07 year
STA 37,X
*
RF3 CLRA
LDB #3
JSR WRITSC
*
* LDX #BUFFER
* CLRA
* LDB #1
* JSR READSC
* LDX #BUFFER
* LDA #$AA set the init flag
* STA 0,X
* LDA #$55
* STA 1,X
* CLRA
* LDB #1
* JSR WRITSC
*
* Write Boot sector
*
LDX #$C000
CLRA TRACK 0
LDB #$01 SECTOR 1
STA TRACK
STB SECTOR
LBSR WRITSC
*
UFEXIT LDX #UFMSG1
JMP PDATA1
*
*
** FLEX 9 COMPACT FLASH DISK DRIVERS
*
* FOR SYS09BUG 1.2 ON THE BURCHED B5-X300
* WITH I/O MAPPED AT $XE000
* AND ROM MAPPED AT $XF000
* THE BURCHED B5-X300 HAS 256KBYTES OF SRAM
* THE FIRST 64K IS USED BY FLEX,
* THE SECOND 192K MAY BE USED AS A RAM DISK
*
*
IMASK EQU $10 IRQ MASK CC
FMASK EQU $40 FIRQ MASK CC
DATREG EQU $FFF0 DAT REGISTERS
*
CF_BASE EQU $E040
CF_DATA EQU CF_BASE+0
CF_ERROR EQU CF_BASE+1 ; read error
CF_FEATURE EQU CF_BASE+1 ; write feature
CF_SCNT EQU CF_BASE+2
CF_SNUM EQU CF_BASE+3
CF_CLO EQU CF_BASE+4
CF_CHI EQU CF_BASE+5
CF_HEAD EQU CF_BASE+6
CF_STATUS EQU CF_BASE+7 ; read status
CF_COMAND EQU CF_BASE+7 ; write command
*
* Command Equates
*
CMDREAD EQU $20 ; Read Single sector
CMDWRITE EQU $30 ; Write Single sector
CMDFEATURE EQU $EF
FEAT8BIT EQU $01 ; enable 8 bit transfers
HEADLBA EQU $E0
*
* Status bit equates
*
BSY EQU $80
DRDY EQU $40
DRQ EQU $08
ERR EQU $01
*
*
* INITIALIZE CF CARD FOR 8 BIT LBA MODE
*
INITDR BSR WAITRDY
LDA #HEADLBA
STA CF_HEAD
LDA #FEAT8BIT
STA CF_FEATURE
LDA #CMDFEATURE
STA CF_COMAND
BRA WAITRDY
*
* RESTORE DISK DRIVER (SEEK TRACK 00)
*
RESTR1 BSR DRVSEL
CLRA ; Track 0
LDB #$01 ; Sector 1
*
* Seek track and sector
* A holds track number (0 - ??)
* B holds sector number (1 - ??)
* Sector numbers starts from 1
* subtract 1 to start from sector 0 on CF
*
SEEKTS DECB
STB CF_SNUM
STA CF_CLO
LDB DRVNUM
STB CF_CHI
LDB #$01
STB CF_SCNT
CLRB
RTS
*
* READ SECTORS FROM CF
*
*
READSC BSR SEEKTS
LDA #CMDREAD ; IDE READ MULTIPLE
STA CF_COMAND
BSR WAITRDY
*
* READ LOOP
*
CLRB
RDLP1 BSR WAITDRQ
LDA CF_DATA
STA ,X+
DECB
BNE RDLP1
*
CLRB
RDLP2 BSR WAITDRQ
LDA CF_DATA
DECB
BNE RDLP2
*
BSR WAITRDY
CLRB
RTS
*
* WRITE SECTOR TO CF
*
WRITSC BSR SEEKTS ; SEEK TRACK & SECTOR
LDA #CMDWRITE ; IDE WRITE MULTIPLE
STA CF_COMAND
BSR WAITRDY
*
* WRITE LOOP
*
CLRB
WRTLP1 BSR WAITDRQ
LDA ,X+
STA CF_DATA
DECB
BNE WRTLP1
*
CLRB
WRTLP2 BSR WAITDRQ
CLRA
STA CF_DATA
DECB
BNE WRTLP2
*
BSR WAITRDY
CLRB
RTS
*
* CHECK FOR BUSY
* Doubles as VERIFY
*
BUSY CLRB Never busy
RTS
*
* DRIVE SELECT DISK DRIVER
*
DRVSEL LDA 3,X GET DRIVE # FROM FCB
CMPA #3
BLS DRVS2 IF > 3, SET IT TO 0
CLRA
DRVS2 STA DRVNUM
CLRB ; SET Z, CLEAR C
RTS
*
* CHECK DRIVE READY DISK DRIVER
*
CHKDRV LDA 3,X
CLRB ; CLEAR C, SET Z
RTS
*
* WAIT UNTIL READY
*
WAITRDY LDA CF_STATUS
BITA #BSY
BNE WAITRDY
LDA CF_STATUS
BITA #DRDY
BEQ WAITRDY
RTS
*
* WAIT FOR DATA REQUEST
*
WAITDRQ LDA CF_STATUS
BITA #DRQ
BEQ WAITDRQ
RTS
*
*******************************************************
*
* Bootstrap FLEX Loader
*
* SBUG1.8 loads the bootstap loader at $C000
* however the Flex adaption manual has the
* bootstrap loader residing at $C100
*
******************************************************
*
* Equates
*
STACK EQU $C0FF
SCTBUF EQU $C300
*
* Start of Utility
*
ORG $C000
BOOT BRA LOAD0
FCB 0,0,0
TRK FCB 0 File start track
SCT FCB 0 File start sector
DNS FCB 0 Density Flag (not used)
TADR FDB $C000 Transfer address
LADR FDB 0 Load Address
DRNUM FCB 0 Drive number 0
*
LOAD0 LDS #STACK Set up stack
LDD TRK Set up start track and sector
STD SCTBUF
LDY #SCTBUF+256
*
* Perform actual file load
*
LOAD1 BSR GETCH Get acharcater
CMPA #$02 Data record hearder ?
BEQ LOAD2 Skip, is so
CMPA #$16 Xfr address hearder ?
BNE LOAD1 Loop if neither
*
* Get transfer address
*
BSR GETCH
STA TADR
BSR GETCH
STA TADR+1
BRA LOAD1
*
* Load data record
*
LOAD2 BSR GETCH Get load address
STA LADR
BSR GETCH
STA LADR+1
BSR GETCH Get Bytes count
TFR A,B
TSTB
BEQ LOAD1 Loop if count = 0
LDX LADR Get load address
LOAD3 PSHS B,X
BSR GETCH Get data character
PULS B,X
STA ,X+ Store at load address
DECB
BNE LOAD3 Loop until count = 0
BRA LOAD1
*
* Get Character routine
* Reads a sector if needed
*
GETCH CMPY #SCTBUF+256 out of data ?
BNE GETCH4 Go read Character if not
GETCH2 LDX #SCTBUF Point to buffer
LDD 0,X Get forward Link
BEQ GO if zero, file is loaded
BSR READ Read next sector
BNE BOOT start over if error
LDY #SCTBUF+4 Point past link
GETCH4 LDA ,Y+ Else, get a character
RTS
*
* File is loaded, Jump to it
*
GO JMP [TADR] Jump to transfer address
*
** FLEX 9 COMPACT FLASH DISK DRIVERS
*
* FOR SYS09BUG 1.2 ON THE BURCHED B5-X300
* WITH I/O MAPPED AT $XE000
* AND ROM MAPPED AT $XF000
* THE BURCHED B5-X300 HAS 256KBYTES OF SRAM
* THE FIRST 64K IS USED BY FLEX,
* THE SECOND 192K MAY BE USED AS A RAM DISK
*
*
*IMASK EQU $10 IRQ MASK CC
*FMASK EQU $40 FIRQ MASK CC
*DATREG EQU $FFF0 DAT REGISTERS
*
*CF_BASE EQU $E040
*CF_DATA EQU CF_BASE+0
*CF_ERROR EQU CF_BASE+1 ; read error
*CF_FEATURE EQU CF_BASE+1 ; write feature
*CF_SCNT EQU CF_BASE+2
*CF_SNUM EQU CF_BASE+3
*CF_CLO EQU CF_BASE+4
*CF_CHI EQU CF_BASE+5
*CF_HEAD EQU CF_BASE+6
*CF_STATUS EQU CF_BASE+7 ; read status
*CF_COMAND EQU CF_BASE+7 ; write command
*
* Command Equates
*
*CMDREAD EQU $20 ; Read Single sector
*CMDWRITE EQU $30 ; Write Single sector
*CMDFEATURE EQU $EF
*FEAT8BIT EQU $01 ; enable 8 bit transfers
*HEADLBA EQU $E0
*
* Status bit equates
*
*BSY EQU $80
*DRDY EQU $40
*DRQ EQU $08
*ERR EQU $01
*
* Seek track and sector
* A holds track number (0 - ??)
* B holds sector number (1 - ??)
* Sector numbers starts from 1
* subtract 1 to start from sector 0 on CF
*
SEEK DECB
STB CF_SNUM
STA CF_CLO
LDB DRNUM
STB CF_CHI
LDB #$01
STB CF_SCNT
CLRB
RTS
*
* READ SECTORS FROM CF
*
*
READ BSR SEEK
LDA #CMDREAD ; IDE READ MULTIPLE
STA CF_COMAND
BSR WTRDY
*
* READ LOOP
*
CLRB
READ1 BSR WTDRQ
LDA CF_DATA
STA ,X+
DECB
BNE READ1
*
CLRB
READ2 BSR WTDRQ
LDA CF_DATA
DECB
BNE READ2
*
BSR WTRDY
CLRB
RTS
*
* WAIT UNTIL READY
*
WTRDY LDA CF_STATUS
BITA #BSY
BNE WTRDY
LDA CF_STATUS
BITA #DRDY
BEQ WTRDY
RTS
*
* WAIT FOR DATA REQUEST
*
WTDRQ LDA CF_STATUS
BITA #DRQ
BEQ WTDRQ
RTS
*
END START
Go to most recent revision | Compare with Previous | Blame | View Log