URL
https://opencores.org/ocsvn/minsoc/minsoc/trunk
Subversion Repositories minsoc
[/] [minsoc/] [trunk/] [prj/] [src/] [blackboxes/] [ethmac.v] - Rev 85
Compare with Previous | Blame | View Log
`include "ethmac_defines.v" module ethmac ( // WISHBONE common wb_clk_i, wb_rst_i, wb_dat_i, wb_dat_o, // WISHBONE slave wb_adr_i, wb_sel_i, wb_we_i, wb_cyc_i, wb_stb_i, wb_ack_o, wb_err_o, // WISHBONE master m_wb_adr_o, m_wb_sel_o, m_wb_we_o, m_wb_dat_o, m_wb_dat_i, m_wb_cyc_o, m_wb_stb_o, m_wb_ack_i, m_wb_err_i, `ifdef ETH_WISHBONE_B3 m_wb_cti_o, m_wb_bte_o, `endif //TX mtx_clk_pad_i, mtxd_pad_o, mtxen_pad_o, mtxerr_pad_o, //RX mrx_clk_pad_i, mrxd_pad_i, mrxdv_pad_i, mrxerr_pad_i, mcoll_pad_i, mcrs_pad_i, // MIIM mdc_pad_o, md_pad_i, md_pad_o, md_padoe_o, int_o // Bist `ifdef ETH_BIST , // debug chain signals mbist_si_i, // bist scan serial in mbist_so_o, // bist scan serial out mbist_ctrl_i // bist chain shift control `endif ); parameter Tp = 1; // WISHBONE common input wb_clk_i; // WISHBONE clock input wb_rst_i; // WISHBONE reset input [31:0] wb_dat_i; // WISHBONE data input output [31:0] wb_dat_o; // WISHBONE data output output wb_err_o; // WISHBONE error output // WISHBONE slave input [11:2] wb_adr_i; // WISHBONE address input input [3:0] wb_sel_i; // WISHBONE byte select input input wb_we_i; // WISHBONE write enable input input wb_cyc_i; // WISHBONE cycle input input wb_stb_i; // WISHBONE strobe input output wb_ack_o; // WISHBONE acknowledge output // WISHBONE master output [31:0] m_wb_adr_o; output [3:0] m_wb_sel_o; output m_wb_we_o; input [31:0] m_wb_dat_i; output [31:0] m_wb_dat_o; output m_wb_cyc_o; output m_wb_stb_o; input m_wb_ack_i; input m_wb_err_i; wire [29:0] m_wb_adr_tmp; `ifdef ETH_WISHBONE_B3 output [2:0] m_wb_cti_o; // Cycle Type Identifier output [1:0] m_wb_bte_o; // Burst Type Extension `endif // Tx input mtx_clk_pad_i; // Transmit clock (from PHY) output [3:0] mtxd_pad_o; // Transmit nibble (to PHY) output mtxen_pad_o; // Transmit enable (to PHY) output mtxerr_pad_o; // Transmit error (to PHY) // Rx input mrx_clk_pad_i; // Receive clock (from PHY) input [3:0] mrxd_pad_i; // Receive nibble (from PHY) input mrxdv_pad_i; // Receive data valid (from PHY) input mrxerr_pad_i; // Receive data error (from PHY) // Common Tx and Rx input mcoll_pad_i; // Collision (from PHY) input mcrs_pad_i; // Carrier sense (from PHY) // MII Management interface input md_pad_i; // MII data input (from I/O cell) output mdc_pad_o; // MII Management data clock (to PHY) output md_pad_o; // MII data output (to I/O cell) output md_padoe_o; // MII data output enable (to I/O cell) output int_o; // Interrupt output // Bist `ifdef ETH_BIST input mbist_si_i; // bist scan serial in output mbist_so_o; // bist scan serial out input [`ETH_MBIST_CTRL_WIDTH - 1:0] mbist_ctrl_i; // bist chain shift control `endif endmodule