OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [trunk/] [syn/] [altera/] [Makefile] - Rev 101

Go to most recent revision | Compare with Previous | Blame | View Log

MINSOC = ..
MINSOC_DEFINES = ${MINSOC}/backend
MINSOC_RTL = ${MINSOC}/rtl/verilog
MINSOC_STARTUP_RTL = ${MINSOC_RTL}/minsoc_startup
UART_RTL = ${MINSOC_RTL}/uart16550/rtl/verilog
ADV_DEBUG_ROOT = ${MINSOC_RTL}/adv_debug_sys/Hardware
DEBUG_RTL = ${ADV_DEBUG_ROOT}/adv_dbg_if/rtl/verilog
OR1200_RTL = ${MINSOC_RTL}/or1200/rtl/verilog
ETH_RTL = ${MINSOC_RTL}/ethmac/rtl/verilog
BUILD_SUPPORT = $(MINSOC)/syn/buildSupport
PROJECT_DIR = $(MINSOC)/prj/altera
QSF_FILE = $(BUILD_SUPPORT)/minsoc_top
help:
        @echo "  all: Synthesize and implement the SoC, then generate a bit stream"
        @echo ""
        @echo "  bitgen: Generate a programming file for the target FPGA"
        @echo "  map: Express the SoC netlist in the target hardware"
        @echo "  fit: Place the target hardware, then route the wires"
        @echo "  sta: Perfom a timming analysis"
        @echo "  eda: Generate a netlist of the hardware"
        @echo "  config: Load the bitstream into the device using ALTERA USB Blaster and JTAG configuration"
        @echo ""
        @echo "  clean: Delete all superfluous files generated by Altera tools"
        @echo "  distclean: Delete all generated files"

all: bitgen eda sta
map: $(BUILD_SUPPORT)/minsoc_top.map.summary
fit: $(BUILD_SUPPORT)/minsoc_top.fit.summary
bitgen: minsoc_top.sof
eda: $(BUILD_SUPPORT)/minsoc_top.eda.summary
sta: $(BUILD_SUPPORT)/minsoc_top.sta.summary

#minsoc_top.map.summary: ${MINSOC_RTL}/*.v $(UART_RTL)/*.v $(ADV_DEBUG_ROOT)/*.v  $(DEBUG_RTL)/*.v $(OR1200_RTL)/*.v  $(ETH_RTL)/*.v ${MINSOC_DEFINES}/minsoc_defines.v minsoc_top.qsf
$(BUILD_SUPPORT)/minsoc_top.map.summary: ${MINSOC_DEFINES}/minsoc_defines.v $(BUILD_SUPPORT)/minsoc_top.qsf

        quartus_map $(QSF_FILE) --write_settings_files=off

$(BUILD_SUPPORT)/minsoc_top.fit.summary: $(BUILD_SUPPORT)/minsoc_top.map.summary
        quartus_fit $(QSF_FILE) --write_Settings_files=off --pack_register=minimize_area

minsoc_top.sof: $(BUILD_SUPPORT)/minsoc_top.fit.summary
        quartus_asm $(QSF_FILE)
        mv $(BUILD_SUPPORT)/*.sof .

$(BUILD_SUPPORT)/minsoc_top.sta.summary: $(BUILD_SUPPORT)/minsoc_top.fit.summary
        quartus_sta $(QSF_FILE)

$(BUILD_SUPPORT)/minsoc_top.eda.summary: $(BUILD_SUPPORT)/minsoc_top.fit.summary
        quartus_eda $(QSF_FILE) --write_settings_files=off

config: minsoc_top.sof
        quartus_pgm -c USB-Blaster -m jtag -o "p;minsoc_top.sof"

distclean:
        $(RM) *.sof
        make clean

clean:
        $(RM) $(BUILD_SUPPORT)/*.rpt $(BUILD_SUPPORT)/*.summary $(BUILD_SUPPORT)/*.jdi $(BUILD_SUPPORT)/*.smsg $(BUILD_SUPPORT)/*.pin $(BUILD_SUPPORT)/*.qpf 
        $(RM) -r $(BUILD_SUPPORT)/db $(BUILD_SUPPORT)/incremental_db

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.