OpenCores
URL https://opencores.org/ocsvn/open8_urisc/open8_urisc/trunk

Subversion Repositories open8_urisc

[/] [open8_urisc/] [trunk/] [VHDL/] [o8_gpio.vhd] - Rev 167

Go to most recent revision | Compare with Previous | Blame | View Log

-- Copyright (c)2013 Jeremy Seth Henry
-- All rights reserved.
--
-- Redistribution and use in source and binary forms, with or without
-- modification, are permitted provided that the following conditions are met:
--     * Redistributions of source code must retain the above copyright
--       notice, this list of conditions and the following disclaimer.
--     * Redistributions in binary form must reproduce the above copyright
--       notice, this list of conditions and the following disclaimer in the
--       documentation and/or other materials provided with the distribution,
--       where applicable (as part of a user interface, debugging port, etc.)
--
-- THIS SOFTWARE IS PROVIDED BY JEREMY SETH HENRY ``AS IS'' AND ANY
-- EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
-- WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-- DISCLAIMED. IN NO EVENT SHALL JEREMY SETH HENRY BE LIABLE FOR ANY
-- DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
-- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
-- LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
-- ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
-- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
-- SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
--
-- VHDL Units :  o8_gpio
-- Description:  Provides a single 8-bit GPIO register
 
library ieee;
use ieee.std_logic_1164.all;
 
library work;
  use work.open8_pkg.all;
 
entity o8_gpio is
generic(
  Default_Out           : DATA_TYPE := x"00";
  Default_En            : DATA_TYPE := x"00";
  Reset_Level           : std_logic := '1';
  Input_Only            : boolean := false;
  Address               : ADDRESS_TYPE
);
port(
  Clock                 : in  std_logic;
  Reset                 : in  std_logic;
  --
  Bus_Address           : in  ADDRESS_TYPE;
  Wr_Enable             : in  std_logic;
  Wr_Data               : in  DATA_TYPE;
  Rd_Enable             : in  std_logic;
  Rd_Data               : out DATA_TYPE;
  --
  GPIO                  : inout DATA_TYPE
);
end entity;
 
architecture behave of o8_gpio is
 
  constant User_Addr    : std_logic_vector(15 downto 2)
                          := Address(15 downto 2);
  alias  Comp_Addr      is Bus_Address(15 downto 2);
  alias  Reg_Addr       is Bus_Address(1 downto 0);
  signal Reg_Sel        : std_logic_vector(1 downto 0);
  signal Addr_Match     : std_logic;
  signal Wr_En          : std_logic;
  signal Wr_Data_q      : DATA_TYPE;
  signal Rd_En          : std_logic;
 
  signal User_Out       : DATA_TYPE;
  signal User_En        : DATA_TYPE;
  signal User_In        : DATA_TYPE;
 
begin
 
  Addr_Match            <= '1' when Comp_Addr = User_Addr else '0';
 
  io_reg: process( Clock, Reset )
  begin
    if( Reset = Reset_Level )then
      Reg_Sel           <= "00";
      Rd_En             <= '0';
      Rd_Data           <= x"00";
      if( not Input_Only )then
        Wr_En           <= '0';
        Wr_Data_q       <= x"00";
        User_Out        <= Default_Out;
        User_En         <= Default_En;
      end if;
    elsif( rising_edge( Clock ) )then
      Reg_Sel           <= Reg_Addr;
 
      if( not Input_Only )then
        Wr_En           <= Addr_Match and Wr_Enable;
        Wr_Data_q       <= Wr_Data;
        if( Wr_En = '1' )then
          case( Reg_Sel )is
            when "00" =>
              User_Out  <= Wr_Data_q;
            when "01" =>
              User_En   <= Wr_Data_q;
            when others => null;
          end case;
        end if;
      end if;
 
      User_In           <= GPIO;
 
      Rd_Data           <= (others => '0');
      Rd_En             <= Addr_Match and Rd_Enable;
      if( Rd_En = '1' )then
        if( Input_Only )then
          Rd_Data       <= User_In;
        else
          case( Reg_Sel )is
            when "00" =>
              Rd_Data     <= User_Out;
            when "01" =>
              Rd_Data     <= User_En;
            when "10" =>
              Rd_Data     <= User_In;
            when others => null;
          end case;
        end if;
      end if;
    end if;
  end process;
 
Input_Only_is_True: if( Input_Only )generate
  GPIO                  <= (others => 'Z');
end generate;
 
Input_Only_is_False: if( not Input_Only )generate
 
  Output_Ctl_proc: process( User_Out, User_En )
  begin
    for i in 0 to 7 loop
      GPIO(i)           <= 'Z';
      if( User_En(i) = '1' )then
        GPIO(i)         <= User_Out(i);
      end if;
    end loop;
  end process;
 
end generate;
 
end architecture;
 

Go to most recent revision | Compare with Previous | Blame | View Log

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.