URL
https://opencores.org/ocsvn/qaz_libs/qaz_libs/trunk
Subversion Repositories qaz_libs
[/] [qaz_libs/] [trunk/] [zed_board/] [src/] [zedboard_master_XDC_RevC_D_v2.xdc] - Rev 51
Go to most recent revision | Compare with Previous | Blame | View Log
# ----------------------------------------------------------------------------
# _____
# / \
# /____ \____
# / \===\ \==/
# /___\===\___\/ AVNET Design Resource Center
# \======/ www.em.avnet.com/drc
# \====/
# ----------------------------------------------------------------------------
#
# Created With Avnet UCF Generator V0.4.0
# Date: Saturday, June 30, 2012
# Time: 12:18:55 AM
#
# This design is the property of Avnet. Publication of this
# design is not authorized without written consent from Avnet.
#
# Please direct any questions to:
# ZedBoard.org Community Forums
# http://www.zedboard.org
#
# Disclaimer:
# Avnet, Inc. makes no warranty for the use of this code or design.
# This code is provided "As Is". Avnet, Inc assumes no responsibility for
# any errors, which may appear in this code, nor does it make a commitment
# to update the information contained herein. Avnet, Inc specifically
# disclaims any implied warranties of fitness for a particular purpose.
# Copyright(c) 2012 Avnet, Inc.
# All rights reserved.
#
# ----------------------------------------------------------------------------
#
# Notes:
#
# 10 August 2012
# IO standards based upon Bank 34 and Bank 35 Vcco supply options of 1.8V,
# 2.5V, or 3.3V are possible based upon the Vadj jumper (J18) settings.
# By default, Vadj is expected to be set to 1.8V but if a different
# voltage is used for a particular design, then the corresponding IO
# standard within this UCF should also be updated to reflect the actual
# Vadj jumper selection.
#
# 09 September 2012
# Net names are not allowed to contain hyphen characters '-' since this
# is not a legal VHDL87 or Verilog character within an identifier.
# HDL net names are adjusted to contain no hyphen characters '-' but
# rather use underscore '_' characters. Comment net name with the hyphen
# characters will remain in place since these are intended to match the
# schematic net names in order to better enable schematic search.
#
# 17 April 2014
# Pin constraint for toggle switch SW7 was corrected to M15 location.
#
# 16 April 2015
# Corrected the way that entire banks are assigned to a particular IO
# standard so that it works with more recent versions of Vivado Design
# Suite and moved the IO standard constraints to the end of the file
# along with some better organization and notes like we do with our SOMs.
#
# ----------------------------------------------------------------------------
# ----------------------------------------------------------------------------
# Audio Codec - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN AB1 [get_ports {AC_ADR0}]; # "AC-ADR0"
set_property PACKAGE_PIN Y5 [get_ports {AC_ADR1}]; # "AC-ADR1"
set_property PACKAGE_PIN Y8 [get_ports {AC_GPIO0}]; # "AC-GPIO0"
set_property PACKAGE_PIN AA7 [get_ports {AC_GPIO1}]; # "AC-GPIO1"
set_property PACKAGE_PIN AA6 [get_ports {AC_GPIO2}]; # "AC-GPIO2"
set_property PACKAGE_PIN Y6 [get_ports {AC_GPIO3}]; # "AC-GPIO3"
set_property PACKAGE_PIN AB2 [get_ports {AC_MCLK}]; # "AC-MCLK"
set_property PACKAGE_PIN AB4 [get_ports {AC_SCK}]; # "AC-SCK"
set_property PACKAGE_PIN AB5 [get_ports {AC_SDA}]; # "AC-SDA"
# ----------------------------------------------------------------------------
# Clock Source - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN Y9 [get_ports {GCLK}]; # "GCLK"
# ----------------------------------------------------------------------------
# JA Pmod - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN Y11 [get_ports {JA1}]; # "JA1"
set_property PACKAGE_PIN AA8 [get_ports {JA10}]; # "JA10"
set_property PACKAGE_PIN AA11 [get_ports {JA2}]; # "JA2"
set_property PACKAGE_PIN Y10 [get_ports {JA3}]; # "JA3"
set_property PACKAGE_PIN AA9 [get_ports {JA4}]; # "JA4"
set_property PACKAGE_PIN AB11 [get_ports {JA7}]; # "JA7"
set_property PACKAGE_PIN AB10 [get_ports {JA8}]; # "JA8"
set_property PACKAGE_PIN AB9 [get_ports {JA9}]; # "JA9"
# ----------------------------------------------------------------------------
# JB Pmod - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN W12 [get_ports {JB1}]; # "JB1"
set_property PACKAGE_PIN V8 [get_ports {JB10}]; # "JB10"
set_property PACKAGE_PIN W11 [get_ports {JB2}]; # "JB2"
set_property PACKAGE_PIN V10 [get_ports {JB3}]; # "JB3"
set_property PACKAGE_PIN W8 [get_ports {JB4}]; # "JB4"
set_property PACKAGE_PIN V12 [get_ports {JB7}]; # "JB7"
set_property PACKAGE_PIN W10 [get_ports {JB8}]; # "JB8"
set_property PACKAGE_PIN V9 [get_ports {JB9}]; # "JB9"
# ----------------------------------------------------------------------------
# JC Pmod - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN AB6 [get_ports {JC1_N}]; # "JC1_N"
set_property PACKAGE_PIN AB7 [get_ports {JC1_P}]; # "JC1_P"
set_property PACKAGE_PIN AA4 [get_ports {JC2_N}]; # "JC2_N"
set_property PACKAGE_PIN Y4 [get_ports {JC2_P}]; # "JC2_P"
set_property PACKAGE_PIN T6 [get_ports {JC3_N}]; # "JC3_N"
set_property PACKAGE_PIN R6 [get_ports {JC3_P}]; # "JC3_P"
set_property PACKAGE_PIN U4 [get_ports {JC4_N}]; # "JC4_N"
set_property PACKAGE_PIN T4 [get_ports {JC4_P}]; # "JC4_P"
# ----------------------------------------------------------------------------
# JA Pmod - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN W7 [get_ports {JD1_N}]; # "JD1_N"
set_property PACKAGE_PIN V7 [get_ports {JD1_P}]; # "JD1_P"
set_property PACKAGE_PIN V4 [get_ports {JD2_N}]; # "JD2_N"
set_property PACKAGE_PIN V5 [get_ports {JD2_P}]; # "JD2_P"
set_property PACKAGE_PIN W5 [get_ports {JD3_N}]; # "JD3_N"
set_property PACKAGE_PIN W6 [get_ports {JD3_P}]; # "JD3_P"
set_property PACKAGE_PIN U5 [get_ports {JD4_N}]; # "JD4_N"
set_property PACKAGE_PIN U6 [get_ports {JD4_P}]; # "JD4_P"
# ----------------------------------------------------------------------------
# OLED Display - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN U10 [get_ports {OLED_DC}]; # "OLED-DC"
set_property PACKAGE_PIN U9 [get_ports {OLED_RES}]; # "OLED-RES"
set_property PACKAGE_PIN AB12 [get_ports {OLED_SCLK}]; # "OLED-SCLK"
set_property PACKAGE_PIN AA12 [get_ports {OLED_SDIN}]; # "OLED-SDIN"
set_property PACKAGE_PIN U11 [get_ports {OLED_VBAT}]; # "OLED-VBAT"
set_property PACKAGE_PIN U12 [get_ports {OLED_VDD}]; # "OLED-VDD"
# ----------------------------------------------------------------------------
# HDMI Output - Bank 33
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN W18 [get_ports {HD_CLK}]; # "HD-CLK"
set_property PACKAGE_PIN Y13 [get_ports {HD_D0}]; # "HD-D0"
set_property PACKAGE_PIN AA13 [get_ports {HD_D1}]; # "HD-D1"
set_property PACKAGE_PIN W13 [get_ports {HD_D10}]; # "HD-D10"
set_property PACKAGE_PIN W15 [get_ports {HD_D11}]; # "HD-D11"
set_property PACKAGE_PIN V15 [get_ports {HD_D12}]; # "HD-D12"
set_property PACKAGE_PIN U17 [get_ports {HD_D13}]; # "HD-D13"
set_property PACKAGE_PIN V14 [get_ports {HD_D14}]; # "HD-D14"
set_property PACKAGE_PIN V13 [get_ports {HS_D15}]; # "HD-D15"
set_property PACKAGE_PIN AA14 [get_ports {HD_D2}]; # "HD-D2"
set_property PACKAGE_PIN Y14 [get_ports {HD_D3}]; # "HD-D3"
set_property PACKAGE_PIN AB15 [get_ports {HD_D4}]; # "HD-D4"
set_property PACKAGE_PIN AB16 [get_ports {HD_D5}]; # "HD-D5"
set_property PACKAGE_PIN AA16 [get_ports {HD_D6}]; # "HD-D6"
set_property PACKAGE_PIN AB17 [get_ports {HD_D7}]; # "HD-D7"
set_property PACKAGE_PIN AA17 [get_ports {HD_D8}]; # "HD-D8"
set_property PACKAGE_PIN Y15 [get_ports {HD_D9}]; # "HD-D9"
set_property PACKAGE_PIN U16 [get_ports {HD_DE}]; # "HD-DE"
set_property PACKAGE_PIN V17 [get_ports {HD_HSYNC}]; # "HD-HSYNC"
set_property PACKAGE_PIN W16 [get_ports {HD_INT}]; # "HD-INT"
set_property PACKAGE_PIN AA18 [get_ports {HD_SCL}]; # "HD-SCL"
set_property PACKAGE_PIN Y16 [get_ports {HD_SDA}]; # "HD-SDA"
set_property PACKAGE_PIN U15 [get_ports {HD_SPDIF}]; # "HD-SPDIF"
set_property PACKAGE_PIN Y18 [get_ports {HD_SPDIFO}]; # "HD-SPDIFO"
set_property PACKAGE_PIN W17 [get_ports {HD_VSYNC}]; # "HD-VSYNC"
# ----------------------------------------------------------------------------
# User LEDs - Bank 33
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN T22 [get_ports {LD0}]; # "LD0"
set_property PACKAGE_PIN T21 [get_ports {LD1}]; # "LD1"
set_property PACKAGE_PIN U22 [get_ports {LD2}]; # "LD2"
set_property PACKAGE_PIN U21 [get_ports {LD3}]; # "LD3"
set_property PACKAGE_PIN V22 [get_ports {LD4}]; # "LD4"
set_property PACKAGE_PIN W22 [get_ports {LD5}]; # "LD5"
set_property PACKAGE_PIN U19 [get_ports {LD6}]; # "LD6"
set_property PACKAGE_PIN U14 [get_ports {LD7}]; # "LD7"
# ----------------------------------------------------------------------------
# VGA Output - Bank 33
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN Y21 [get_ports {VGA_B1}]; # "VGA-B1"
set_property PACKAGE_PIN Y20 [get_ports {VGA_B2}]; # "VGA-B2"
set_property PACKAGE_PIN AB20 [get_ports {VGA_B3}]; # "VGA-B3"
set_property PACKAGE_PIN AB19 [get_ports {VGA_B4}]; # "VGA-B4"
set_property PACKAGE_PIN AB22 [get_ports {VGA_G1}]; # "VGA-G1"
set_property PACKAGE_PIN AA22 [get_ports {VGA_G2}]; # "VGA-G2"
set_property PACKAGE_PIN AB21 [get_ports {VGA_G3}]; # "VGA-G3"
set_property PACKAGE_PIN AA21 [get_ports {VGA_G4}]; # "VGA-G4"
set_property PACKAGE_PIN AA19 [get_ports {VGA_HS}]; # "VGA-HS"
set_property PACKAGE_PIN V20 [get_ports {VGA_R1}]; # "VGA-R1"
set_property PACKAGE_PIN U20 [get_ports {VGA_R2}]; # "VGA-R2"
set_property PACKAGE_PIN V19 [get_ports {VGA_R3}]; # "VGA-R3"
set_property PACKAGE_PIN V18 [get_ports {VGA_R4}]; # "VGA-R4"
set_property PACKAGE_PIN Y19 [get_ports {VGA_VS}]; # "VGA-VS"
# ----------------------------------------------------------------------------
# User Push Buttons - Bank 34
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN P16 [get_ports {BTNC}]; # "BTNC"
set_property PACKAGE_PIN R16 [get_ports {BTND}]; # "BTND"
set_property PACKAGE_PIN N15 [get_ports {BTNL}]; # "BTNL"
set_property PACKAGE_PIN R18 [get_ports {BTNR}]; # "BTNR"
set_property PACKAGE_PIN T18 [get_ports {BTNU}]; # "BTNU"
# ----------------------------------------------------------------------------
# USB OTG Reset - Bank 34
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN L16 [get_ports {OTG_VBUSOC}]; # "OTG-VBUSOC"
# # ----------------------------------------------------------------------------
# # XADC GIO - Bank 34
# # ----------------------------------------------------------------------------
# set_property PACKAGE_PIN H15 [get_ports {XADC_GIO0}]; # "XADC-GIO0"
# set_property PACKAGE_PIN R15 [get_ports {XADC_GIO1}]; # "XADC-GIO1"
# set_property PACKAGE_PIN K15 [get_ports {XADC_GIO2}]; # "XADC-GIO2"
# set_property PACKAGE_PIN J15 [get_ports {XADC_GIO3}]; # "XADC-GIO3"
# ----------------------------------------------------------------------------
# Miscellaneous - Bank 34
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN K16 [get_ports {PUDC_B}]; # "PUDC_B"
# ----------------------------------------------------------------------------
# USB OTG Reset - Bank 35
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN G17 [get_ports {OTG_RESETN}]; # "OTG-RESETN"
# ----------------------------------------------------------------------------
# User DIP Switches - Bank 35
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN F22 [get_ports {SW0}]; # "SW0"
set_property PACKAGE_PIN G22 [get_ports {SW1}]; # "SW1"
set_property PACKAGE_PIN H22 [get_ports {SW2}]; # "SW2"
set_property PACKAGE_PIN F21 [get_ports {SW3}]; # "SW3"
set_property PACKAGE_PIN H19 [get_ports {SW4}]; # "SW4"
set_property PACKAGE_PIN H18 [get_ports {SW5}]; # "SW5"
set_property PACKAGE_PIN H17 [get_ports {SW6}]; # "SW6"
set_property PACKAGE_PIN M15 [get_ports {SW7}]; # "SW7"
# # ----------------------------------------------------------------------------
# # XADC AD Channels - Bank 35
# # ----------------------------------------------------------------------------
# set_property PACKAGE_PIN E16 [get_ports {AD0N_R}]; # "XADC-AD0N-R"
# set_property PACKAGE_PIN F16 [get_ports {AD0P_R}]; # "XADC-AD0P-R"
# set_property PACKAGE_PIN D17 [get_ports {AD8N_N}]; # "XADC-AD8N-R"
# set_property PACKAGE_PIN D16 [get_ports {AD8P_R}]; # "XADC-AD8P-R"
# ----------------------------------------------------------------------------
# FMC Expansion Connector - Bank 13
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN R7 [get_ports {FMC_SCL}]; # "FMC-SCL"
set_property PACKAGE_PIN U7 [get_ports {FMC_SDA}]; # "FMC-SDA"
# ----------------------------------------------------------------------------
# FMC Expansion Connector - Bank 33
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN AB14 [get_ports {FMC_PRSNT}]; # "FMC-PRSNT"
# ----------------------------------------------------------------------------
# FMC Expansion Connector - Bank 34
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN L19 [get_ports {FMC_CLK0_N}]; # "FMC-CLK0_N"
set_property PACKAGE_PIN L18 [get_ports {FMC_CLK0_P}]; # "FMC-CLK0_P"
set_property PACKAGE_PIN M20 [get_ports {FMC_LA00_CC_N}]; # "FMC-LA00_CC_N"
set_property PACKAGE_PIN M19 [get_ports {FMC_LA00_CC_P}]; # "FMC-LA00_CC_P"
set_property PACKAGE_PIN N20 [get_ports {FMC_LA01_CC_N}]; # "FMC-LA01_CC_N"
set_property PACKAGE_PIN N19 [get_ports {FMC_LA01_CC_P}]; # "FMC-LA01_CC_P"
set_property PACKAGE_PIN P18 [get_ports {FMC_LA02_N}]; # "FMC-LA02_N"
set_property PACKAGE_PIN P17 [get_ports {FMC_LA02_P}]; # "FMC-LA02_P"
set_property PACKAGE_PIN P22 [get_ports {FMC_LA03_N}]; # "FMC-LA03_N"
set_property PACKAGE_PIN N22 [get_ports {FMC_LA03_P}]; # "FMC-LA03_P"
set_property PACKAGE_PIN M22 [get_ports {FMC_LA04_N}]; # "FMC-LA04_N"
set_property PACKAGE_PIN M21 [get_ports {FMC_LA04_P}]; # "FMC-LA04_P"
set_property PACKAGE_PIN K18 [get_ports {FMC_LA05_N}]; # "FMC-LA05_N"
set_property PACKAGE_PIN J18 [get_ports {FMC_LA05_P}]; # "FMC-LA05_P"
set_property PACKAGE_PIN L22 [get_ports {FMC_LA06_N}]; # "FMC-LA06_N"
set_property PACKAGE_PIN L21 [get_ports {FMC_LA06_P}]; # "FMC-LA06_P"
set_property PACKAGE_PIN T17 [get_ports {FMC_LA07_N}]; # "FMC-LA07_N"
set_property PACKAGE_PIN T16 [get_ports {FMC_LA07_P}]; # "FMC-LA07_P"
set_property PACKAGE_PIN J22 [get_ports {FMC_LA08_N}]; # "FMC-LA08_N"
set_property PACKAGE_PIN J21 [get_ports {FMC_LA08_P}]; # "FMC-LA08_P"
set_property PACKAGE_PIN R21 [get_ports {FMC_LA09_N}]; # "FMC-LA09_N"
set_property PACKAGE_PIN R20 [get_ports {FMC_LA09_P}]; # "FMC-LA09_P"
set_property PACKAGE_PIN T19 [get_ports {FMC_LA10_N}]; # "FMC-LA10_N"
set_property PACKAGE_PIN R19 [get_ports {FMC_LA10_P}]; # "FMC-LA10_P"
set_property PACKAGE_PIN N18 [get_ports {FMC_LA11_N}]; # "FMC-LA11_N"
set_property PACKAGE_PIN N17 [get_ports {FMC_LA11_P}]; # "FMC-LA11_P"
set_property PACKAGE_PIN P21 [get_ports {FMC_LA12_N}]; # "FMC-LA12_N"
set_property PACKAGE_PIN P20 [get_ports {FMC_LA12_P}]; # "FMC-LA12_P"
set_property PACKAGE_PIN M17 [get_ports {FMC_LA13_N}]; # "FMC-LA13_N"
set_property PACKAGE_PIN L17 [get_ports {FMC_LA13_P}]; # "FMC-LA13_P"
set_property PACKAGE_PIN K20 [get_ports {FMC_LA14_N}]; # "FMC-LA14_N"
set_property PACKAGE_PIN K19 [get_ports {FMC_LA14_P}]; # "FMC-LA14_P"
set_property PACKAGE_PIN J17 [get_ports {FMC_LA15_N}]; # "FMC-LA15_N"
set_property PACKAGE_PIN J16 [get_ports {FMC_LA15_P}]; # "FMC-LA15_P"
set_property PACKAGE_PIN K21 [get_ports {FMC_LA16_N}]; # "FMC-LA16_N"
set_property PACKAGE_PIN J20 [get_ports {FMC_LA16_P}]; # "FMC-LA16_P"
# ----------------------------------------------------------------------------
# FMC Expansion Connector - Bank 35
# ----------------------------------------------------------------------------
set_property PACKAGE_PIN C19 [get_ports {FMC_CLK1_N}]; # "FMC-CLK1_N"
set_property PACKAGE_PIN D18 [get_ports {FMC_CLK1_P}]; # "FMC-CLK1_P"
set_property PACKAGE_PIN B20 [get_ports {FMC_LA17_CC_N}]; # "FMC-LA17_CC_N"
set_property PACKAGE_PIN B19 [get_ports {FMC_LA17_CC_P}]; # "FMC-LA17_CC_P"
set_property PACKAGE_PIN C20 [get_ports {FMC_LA18_CC_N}]; # "FMC-LA18_CC_N"
set_property PACKAGE_PIN D20 [get_ports {FMC_LA18_CC_P}]; # "FMC-LA18_CC_P"
set_property PACKAGE_PIN G16 [get_ports {FMC_LA19_N}]; # "FMC-LA19_N"
set_property PACKAGE_PIN G15 [get_ports {FMC_LA19_P}]; # "FMC-LA19_P"
set_property PACKAGE_PIN G21 [get_ports {FMC_LA20_N}]; # "FMC-LA20_N"
set_property PACKAGE_PIN G20 [get_ports {FMC_LA20_P}]; # "FMC-LA20_P"
set_property PACKAGE_PIN E20 [get_ports {FMC_LA21_N}]; # "FMC-LA21_N"
set_property PACKAGE_PIN E19 [get_ports {FMC_LA21_P}]; # "FMC-LA21_P"
set_property PACKAGE_PIN F19 [get_ports {FMC_LA22_N}]; # "FMC-LA22_N"
set_property PACKAGE_PIN G19 [get_ports {FMC_LA22_P}]; # "FMC-LA22_P"
set_property PACKAGE_PIN D15 [get_ports {FMC_LA23_N}]; # "FMC-LA23_N"
set_property PACKAGE_PIN E15 [get_ports {FMC_LA23_P}]; # "FMC-LA23_P"
set_property PACKAGE_PIN A19 [get_ports {FMC_LA24_N}]; # "FMC-LA24_N"
set_property PACKAGE_PIN A18 [get_ports {FMC_LA24_P}]; # "FMC-LA24_P"
set_property PACKAGE_PIN C22 [get_ports {FMC_LA25_N}]; # "FMC-LA25_N"
set_property PACKAGE_PIN D22 [get_ports {FMC_LA25_P}]; # "FMC-LA25_P"
set_property PACKAGE_PIN E18 [get_ports {FMC_LA26_N}]; # "FMC-LA26_N"
set_property PACKAGE_PIN F18 [get_ports {FMC_LA26_P}]; # "FMC-LA26_P"
set_property PACKAGE_PIN D21 [get_ports {FMC_LA27_N}]; # "FMC-LA27_N"
set_property PACKAGE_PIN E21 [get_ports {FMC_LA27_P}]; # "FMC-LA27_P"
set_property PACKAGE_PIN A17 [get_ports {FMC_LA28_N}]; # "FMC-LA28_N"
set_property PACKAGE_PIN A16 [get_ports {FMC_LA28_P}]; # "FMC-LA28_P"
set_property PACKAGE_PIN C18 [get_ports {FMC_LA29_N}]; # "FMC-LA29_N"
set_property PACKAGE_PIN C17 [get_ports {FMC_LA29_P}]; # "FMC-LA29_P"
set_property PACKAGE_PIN B15 [get_ports {FMC_LA30_N}]; # "FMC-LA30_N"
set_property PACKAGE_PIN C15 [get_ports {FMC_LA30_P}]; # "FMC-LA30_P"
set_property PACKAGE_PIN B17 [get_ports {FMC_LA31_N}]; # "FMC-LA31_N"
set_property PACKAGE_PIN B16 [get_ports {FMC_LA31_P}]; # "FMC-LA31_P"
set_property PACKAGE_PIN A22 [get_ports {FMC_LA32_N}]; # "FMC-LA32_N"
set_property PACKAGE_PIN A21 [get_ports {FMC_LA32_P}]; # "FMC-LA32_P"
set_property PACKAGE_PIN B22 [get_ports {FMC_LA33_N}]; # "FMC-LA33_N"
set_property PACKAGE_PIN B21 [get_ports {FMC_LA33_P}]; # "FMC-LA33_P"
# ----------------------------------------------------------------------------
# IOSTANDARD Constraints
#
# Note that these IOSTANDARD constraints are applied to all IOs currently
# assigned within an I/O bank. If these IOSTANDARD constraints are
# evaluated prior to other PACKAGE_PIN constraints being applied, then
# the IOSTANDARD specified will likely not be applied properly to those
# pins. Therefore, bank wide IOSTANDARD constraints should be placed
# within the XDC file in a location that is evaluated AFTER all
# PACKAGE_PIN constraints within the target bank have been evaluated.
#
# Un-comment one or more of the following IOSTANDARD constraints according to
# the bank pin assignments that are required within a design.
# ----------------------------------------------------------------------------
# Note that the bank voltage for IO Bank 33 is fixed to 3.3V on ZedBoard.
set_property IOSTANDARD LVCMOS33 [get_ports -of_objects [get_iobanks 33]];
# Set the bank voltage for IO Bank 34 to 1.8V by default.
# set_property IOSTANDARD LVCMOS33 [get_ports -of_objects [get_iobanks 34]];
# set_property IOSTANDARD LVCMOS25 [get_ports -of_objects [get_iobanks 34]];
set_property IOSTANDARD LVCMOS18 [get_ports -of_objects [get_iobanks 34]];
# Set the bank voltage for IO Bank 35 to 1.8V by default.
# set_property IOSTANDARD LVCMOS33 [get_ports -of_objects [get_iobanks 35]];
# set_property IOSTANDARD LVCMOS25 [get_ports -of_objects [get_iobanks 35]];
set_property IOSTANDARD LVCMOS18 [get_ports -of_objects [get_iobanks 35]];
# Note that the bank voltage for IO Bank 13 is fixed to 3.3V on ZedBoard.
set_property IOSTANDARD LVCMOS33 [get_ports -of_objects [get_iobanks 13]];
set_property CFGBVS VCCO [current_design]
set_property CONFIG_VOLTAGE 3.3 [current_design]
Go to most recent revision | Compare with Previous | Blame | View Log