OpenCores
URL https://opencores.org/ocsvn/System09/System09/trunk

Subversion Repositories System09

[/] - Rev 222

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
222 Added SPI master to project. Pick up Atlys rom davidgb 667d 14h /
221 Completed Atlys option davidgb 667d 14h /
220 checkin davidgb 667d 14h /
219 back out last change davidgb 667d 19h /
218 Added ROM variation for Digilent Atlys board davidgb 667d 19h /
217 Extended debug sw to show keyboard data. PS/2 keyboard now works on USB HID (you must use a PS/2 keyboard + PS/2-to-USB dongle for it to work). davidgb 670d 18h /
216 Get rid of warning about unconnected CLK0 pin davidgb 670d 18h /
215 Update project after switching to xilinx block ram davidgb 670d 21h /
214 Switch to Xilinx block ram davidgb 670d 21h /
213 updated project file davidgb 670d 21h /
212 Switched from VGA output to HDMI output. davidgb 670d 21h /
211 New version of VDU8 that has HDMI output. Still needs work refactoring clock signals. davidgb 670d 21h /
210 Check in code fragment implementing HDMI/TMDS encoding.
Derived from HDMI_test.v https://www.fpga4fun.com/HDMI.html (c) fpga4fun.com & KNJN LLC 2013
davidgb 670d 21h /
209 Started adding in keyboard (not tested).
Added in green-only VGA output thru Pmod port to PmodVGA J2 port.
Started working on HDMI output
davidgb 670d 23h /
208 swapped 32k and 16k ram to use block_spram. davidgb 715d 00h /
207 Updated design to pick up vdu8_spram (which uses parameterized ram for video memory instead of hard macros) davidgb 715d 01h /
206 Update comment/cleanup davidgb 715d 01h /
205 A new version of VDU8 that uses the parameterized xilinx ram "block_spram" for the video memory. davidgb 715d 01h /
204 patched up ram for zybo use davidgb 715d 01h /
203 Added a parameterized ram model. davidgb 715d 01h /
202 Updated Zybo design to reintroduce VDU8 driving the PmodVGA on pmod connectors JC+JD.
This version also uses PmodUSBUART on JE. To use PmodRS232 you must edit the .ucf file and select the appropriate pin LOCs.
davidgb 715d 02h /
201 A copy of XSA-3S1000.ucf and System09_Xess_XSA-3S1000.vhd that have dual serial ports with no handshake. davidgb 721d 20h /
200 Started adding back in video support - VDU8 instantiated and RGBHV bits sent to Pmod JE port. davidgb 728d 18h /
199 Add in full RS-232 handshake for PmodUSBUART. davidgb 729d 19h /
198 Update UCF file to select Pmod pinout compatible with the PmodUSBUART.
To use, make sure PmodUSBUART has JP1 as "LCL". Connect the usb to the uart and open the terminal program. Test the transmission via the LED on the Pmod. Then (carefully) plug into Pmod port on Zybo.
davidgb 729d 20h /
197 Updates from John Kent:
-- 4.5 John Kent 2012-02-04 Re-arranged Rx & Tx Baud clock edge detect.
-- 4.6 John Kent 3021-01-30 Double sample RxC, TxC, and RxD with cpu_clk
-- for 125MHz Clock on Zybo Z7 board.
davidgb 736d 17h /
196 Working system boots to SBUG. Uses RS232 Pmod (no handshake) and 57600,8,N,1 (no handshake) hyperterm. davidgb 736d 18h /
195 Switched to using the UART over usb for the console port. davidgb 736d 18h /
194 Finally have a working board. davidgb 736d 18h /
193 Fixed part of the ACIA problem - the polarity of the NMI was wrong. Now get clean output but input to the ACIA is not working. Also fixed the 32k addressing davidgb 736d 22h /

powered by: WebSVN 2.1.0

© copyright 1999-2023 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.