OpenCores
URL https://opencores.org/ocsvn/System09/System09/trunk

Subversion Repositories System09

[/] [System09/] [trunk/] [rtl/] - Rev 208

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
208 swapped 32k and 16k ram to use block_spram. davidgb 585d 16h /System09/trunk/rtl/
207 Updated design to pick up vdu8_spram (which uses parameterized ram for video memory instead of hard macros) davidgb 585d 17h /System09/trunk/rtl/
206 Update comment/cleanup davidgb 585d 17h /System09/trunk/rtl/
205 A new version of VDU8 that uses the parameterized xilinx ram "block_spram" for the video memory. davidgb 585d 17h /System09/trunk/rtl/
204 patched up ram for zybo use davidgb 585d 17h /System09/trunk/rtl/
203 Added a parameterized ram model. davidgb 585d 17h /System09/trunk/rtl/
202 Updated Zybo design to reintroduce VDU8 driving the PmodVGA on pmod connectors JC+JD.
This version also uses PmodUSBUART on JE. To use PmodRS232 you must edit the .ucf file and select the appropriate pin LOCs.
davidgb 585d 18h /System09/trunk/rtl/
201 A copy of XSA-3S1000.ucf and System09_Xess_XSA-3S1000.vhd that have dual serial ports with no handshake. davidgb 592d 12h /System09/trunk/rtl/
200 Started adding back in video support - VDU8 instantiated and RGBHV bits sent to Pmod JE port. davidgb 599d 10h /System09/trunk/rtl/
199 Add in full RS-232 handshake for PmodUSBUART. davidgb 600d 11h /System09/trunk/rtl/
198 Update UCF file to select Pmod pinout compatible with the PmodUSBUART.
To use, make sure PmodUSBUART has JP1 as "LCL". Connect the usb to the uart and open the terminal program. Test the transmission via the LED on the Pmod. Then (carefully) plug into Pmod port on Zybo.
davidgb 600d 13h /System09/trunk/rtl/
197 Updates from John Kent:
-- 4.5 John Kent 2012-02-04 Re-arranged Rx & Tx Baud clock edge detect.
-- 4.6 John Kent 3021-01-30 Double sample RxC, TxC, and RxD with cpu_clk
-- for 125MHz Clock on Zybo Z7 board.
davidgb 607d 10h /System09/trunk/rtl/
196 Working system boots to SBUG. Uses RS232 Pmod (no handshake) and 57600,8,N,1 (no handshake) hyperterm. davidgb 607d 10h /System09/trunk/rtl/
195 Switched to using the UART over usb for the console port. davidgb 607d 11h /System09/trunk/rtl/
194 Finally have a working board. davidgb 607d 11h /System09/trunk/rtl/
193 Fixed part of the ACIA problem - the polarity of the NMI was wrong. Now get clean output but input to the ACIA is not working. Also fixed the 32k addressing davidgb 607d 14h /System09/trunk/rtl/
192 Fixed part of the ACIA problem - the polarity of the NMI was wrong. Now get clean output but input to the ACIA is not working. davidgb 607d 14h /System09/trunk/rtl/
189 Remove unused file. Created by ISE gui. davidgb 614d 05h /System09/trunk/rtl/
188 update options to match what the ISE gui does davidgb 614d 06h /System09/trunk/rtl/
187 Partially works. Garbage on the ACIA due to baud clock problems. davidgb 614d 11h /System09/trunk/rtl/

1 2 Next >

Show All

powered by: WebSVN 2.1.0

© copyright 1999-2022 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.