| Rev |
Log message |
Author |
Age |
Path |
| 166 |
Turning on warnings for genera_bench.
Updating minsoc-install.sh to work better with directories and working around a missing inclusion of libftdi autotools. http://opencores.org/forum,OpenRISC,0,4685,1 |
rfajardo |
4546d 01h |
/ |
| 165 |
Board contribution: nexys2_1200 (Thanks to Johan Granath)
spartan3e_starter_kit_eth/minsoc_bench_defines.v: deprecated definition updated |
rfajardo |
4563d 02h |
/ |
| 164 |
Updating width of minsoc_tc_top.v for Wishbone B3 compliance. This file has never worked. This solves at least the bug that some signals were not being routed through. |
rfajardo |
4627d 18h |
/ |
| 163 |
Adjusting internal initiator array widths. They were 1 bit too large. Thanks to R. Diez report.
These arrays abstract the complete initiator inputs. This way it is easier to route and arbiter using a single input.
Also removing 2 sequential delays. I didn't design them, so I can't tell if they were really useful/good. |
rfajardo |
4634d 01h |
/ |
| 162 |
Tasks don't have parenthesis. This is only used for ports on modules. This was a mistake from my part. |
rfajardo |
4639d 20h |
/ |
| 161 |
Correcting configure parameters of adv_jtag_bridge on installation script. |
rfajardo |
4652d 23h |
/ |
| 160 |
Typo in minsoc-install.sh script. Adv_jtag_bridge was not configuring correctly. |
rfajardo |
4652d 23h |
/ |
| 159 |
Updated constraint file for de2_115 board. (Richard Hasha) |
rfajardo |
4653d 00h |
/ |
| 158 |
Adding de2_115_board port, thanks to Richard Hasha.
Support to JSP (JTAG Serial Port) working well. Also provided by Richard Hasha.
Different interconnect configurations per board are not straightforward on MinSoC. New added modules or definitions for addresses have to be carried over to other boards. Furthermore, extra modules can be shared among all projects. Thus, it is better to have this centralized:
-Removing interconnect configuration from minsoc_defines.v. There is an interconnect_defines.v file on rtl/verilog. The software counterpart is interconnect.h on sw/drivers.
Including a jsp firmware. It is basically the uart firmware but using JSP instead. Added to all board configure scripts to be compiled on configuration.
prj/srcs extended to include jsp and interconnec_defines.v.
spartan3e_starter_kit_eth lost UART (does not fit) and uses JSP instead now. |
rfajardo |
4654d 16h |
/ |
| 157 |
Removed obsolete file; the changes in this version have been merged into
the mainline advanced debug system version 3.0 and higher. |
nyawn |
4660d 11h |
/ |
| 156 |
Added hardware watchpoint indicators to debug unit break input, to allow
the debugger to break when a hardware watchpoint is triggered. |
nyawn |
4660d 11h |
/ |
| 155 |
Decreased wait time, for faster simulations. |
nyawn |
4660d 11h |
/ |
| 154 |
Modified to use the new autotools support in the advanced debug system v3.0. |
nyawn |
4660d 11h |
/ |
| 153 |
Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. |
rfajardo |
4693d 00h |
/ |
| 152 |
Roll back to retrieve minsoc from branches/rc-1.0. |
rfajardo |
4693d 01h |
/ |
| 151 |
Creating tag release-1.0 from revision 150 of branches/rc-1.0. |
rfajardo |
4693d 01h |
/ |
| 150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4693d 01h |
/ |
| 149 |
Merging differences of release candidate 1.0 revision 140:148 with trunk. |
rfajardo |
4693d 01h |
/ |
| 148 |
Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. |
rfajardo |
4697d 21h |
/ |
| 147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4697d 23h |
/ |
