OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [branches/] - Rev 147

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
147 Updating minsoc_bench.v to correctly acquire uart data.

Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.

Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT

run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.

minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run.
rfajardo 3186d 16h /minsoc/branches/
146 Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. ConX. 3186d 22h /minsoc/branches/
145 minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. rfajardo 3187d 07h /minsoc/branches/
143 Compiling firmwares in board configuration scripts instead of on global minsoc setup. rfajardo 3187d 18h /minsoc/branches/
140 Including required modules for verilator simulation. rfajardo 3187d 19h /minsoc/branches/
139 Creating a verilator branche. rfajardo 3187d 19h /minsoc/branches/
138 DIR_TO_INSTALL creation using wizard ConX. 3188d 07h /minsoc/branches/
137 Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). rfajardo 3188d 18h /minsoc/branches/
136 Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. rfajardo 3195d 14h /minsoc/branches/
134 run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. rfajardo 3202d 18h /minsoc/branches/
133 Roll back minsoc_bench.v to timed simulation. Merge minsoc_bench_core and minsoc_bench_clock again.

Applying Rubén Diez patch to avoid warnings on firmware load for simulation.
rfajardo 3202d 19h /minsoc/branches/
132 ModelSim simulation, running top_module minsoc_bench_clock now, instead of minsoc_bench. rfajardo 3206d 15h /minsoc/branches/
131 Renaming testbench modules. Adding to ifdefs without which the testbench generation can fail. rfajardo 3206d 15h /minsoc/branches/
130 minsoc_bench.v: task test_eth has to be phased out together with the ETHERNET definition. If there is no ETHERNET, test_eth cannot be defined. rfajardo 3206d 17h /minsoc/branches/
129 Removing bugs introduced when splitting clocks and reset.
1) NEGATIVE_RESET or POSITIVE_RESET were missing as definition on minsoc_bench_clock.v (include minsoc_defines.v).
2) wait for reset on minsoc_bench.v to assert design_ready
rfajardo 3207d 04h /minsoc/branches/
128 Outsourcing clocks and reset generations from minsoc_bench.v to minsoc_bench_clock.v. rfajardo 3207d 05h /minsoc/branches/
127 Removing redundant simulation output. rfajardo 3207d 11h /minsoc/branches/
126 Updating information about simulation time for Ethernet test. rfajardo 3207d 11h /minsoc/branches/
125 Adjusting testbench messages. Creating tasks for firmware tests. rfajardo 3207d 12h /minsoc/branches/
124 Removing Verilog delays from minsoc_bench.v. minsoc_bench_defines.v defines now if uart or ethernet have to be tested. If yes, it checks the behavior of the enclosed firmwares. If not, simulation simply runs forever. rfajardo 3207d 13h /minsoc/branches/
123 Renaming reg final to firmware_size. Final is a keyword for Verilator. rfajardo 3207d 18h /minsoc/branches/
122 Renaming minsoc-configure.sh to minsoc-setup.sh. rfajardo 3213d 08h /minsoc/branches/
121 Asserting svn:executable properties of modelsim/*.bat scripts.

Including corrected patch for advanced debug system watchpoints under utils/setup. Configure script updated to use this instead of advanced debug system patches. This will remain so until the patch is corrected. The previous line still has the correct command.
rfajardo 3213d 09h /minsoc/branches/
120 ethmac.prj: a file was missing rfajardo 3213d 12h /minsoc/branches/
119 Tricking Subversion to accept bat files that are now executable. rfajardo 3213d 13h /minsoc/branches/
118 Configure scripts for Xilinx devices updated. All of them require to update or1200_defines.v. The non-standard part uses now the variable $BOARD to print that this board require non-standard update of files. rfajardo 3213d 13h /minsoc/branches/
117 spartan3e_starter_kit designs require DUALPORT from or1200_defines.v to be active instead of GENERIC. rfajardo 3213d 13h /minsoc/branches/
116 Configure scripts were trying to copy/patch projects files before creating them. Ordering is correct now. rfajardo 3213d 14h /minsoc/branches/
115 configure.sh script dir aware.
minsoc-install.sh logging to script dir.
rfajardo 3213d 15h /minsoc/branches/
114 Installation and Configuration scripts can be run out of any directory.
They assume they are going to process the files and directories found in the directory they are run from.
rfajardo 3213d 15h /minsoc/branches/

powered by: WebSVN 2.1.0

© copyright 1999-2020 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.