| Rev |
Log message |
Author |
Age |
Path |
| 153 |
Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. |
rfajardo |
4530d 14h |
/minsoc/branches/ |
| 152 |
Roll back to retrieve minsoc from branches/rc-1.0. |
rfajardo |
4530d 14h |
/minsoc/branches/ |
| 150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4530d 14h |
/minsoc/branches/ |
| 148 |
Renaming minsoc_wave.lxt to minsoc_wave.lxt2 for correctness. |
rfajardo |
4535d 11h |
/minsoc/branches/ |
| 147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4535d 12h |
/minsoc/branches/ |
| 146 |
Importing 'Xilinx Microblaze Dev. Kit 1600E Edition' board configuration directory. |
ConX. |
4535d 18h |
/minsoc/branches/ |
| 145 |
minsoc_bench_core.v and minsoc_bench_clock.v left only on verilator branche. It will develop there until it is ported for inclusion into trunk. RC-1.0 is now clean of it. |
rfajardo |
4536d 03h |
/minsoc/branches/ |
| 143 |
Compiling firmwares in board configuration scripts instead of on global minsoc setup. |
rfajardo |
4536d 14h |
/minsoc/branches/ |
| 140 |
Including required modules for verilator simulation. |
rfajardo |
4536d 14h |
/minsoc/branches/ |
| 139 |
Creating a verilator branche. |
rfajardo |
4536d 14h |
/minsoc/branches/ |
| 138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4537d 03h |
/minsoc/branches/ |
| 137 |
Removing uncomplete support for ml509 and not working support for spartan3e_starter_kit_eth (area constraint cannot be reached). |
rfajardo |
4537d 14h |
/minsoc/branches/ |
| 136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4544d 09h |
/minsoc/branches/ |
| 134 |
run_sim.bat for ModelSim updated to acquire the firmware_size for command line input when running the testbench. |
rfajardo |
4551d 13h |
/minsoc/branches/ |
| 133 |
Roll back minsoc_bench.v to timed simulation. Merge minsoc_bench_core and minsoc_bench_clock again.
Applying Rubén Diez patch to avoid warnings on firmware load for simulation. |
rfajardo |
4551d 15h |
/minsoc/branches/ |
| 132 |
ModelSim simulation, running top_module minsoc_bench_clock now, instead of minsoc_bench. |
rfajardo |
4555d 10h |
/minsoc/branches/ |
| 131 |
Renaming testbench modules. Adding to ifdefs without which the testbench generation can fail. |
rfajardo |
4555d 11h |
/minsoc/branches/ |
| 130 |
minsoc_bench.v: task test_eth has to be phased out together with the ETHERNET definition. If there is no ETHERNET, test_eth cannot be defined. |
rfajardo |
4555d 13h |
/minsoc/branches/ |
| 129 |
Removing bugs introduced when splitting clocks and reset.
1) NEGATIVE_RESET or POSITIVE_RESET were missing as definition on minsoc_bench_clock.v (include minsoc_defines.v).
2) wait for reset on minsoc_bench.v to assert design_ready |
rfajardo |
4556d 00h |
/minsoc/branches/ |
| 128 |
Outsourcing clocks and reset generations from minsoc_bench.v to minsoc_bench_clock.v. |
rfajardo |
4556d 01h |
/minsoc/branches/ |
| 127 |
Removing redundant simulation output. |
rfajardo |
4556d 07h |
/minsoc/branches/ |
| 126 |
Updating information about simulation time for Ethernet test. |
rfajardo |
4556d 07h |
/minsoc/branches/ |
| 125 |
Adjusting testbench messages. Creating tasks for firmware tests. |
rfajardo |
4556d 07h |
/minsoc/branches/ |
| 124 |
Removing Verilog delays from minsoc_bench.v. minsoc_bench_defines.v defines now if uart or ethernet have to be tested. If yes, it checks the behavior of the enclosed firmwares. If not, simulation simply runs forever. |
rfajardo |
4556d 09h |
/minsoc/branches/ |
| 123 |
Renaming reg final to firmware_size. Final is a keyword for Verilator. |
rfajardo |
4556d 14h |
/minsoc/branches/ |
| 122 |
Renaming minsoc-configure.sh to minsoc-setup.sh. |
rfajardo |
4562d 03h |
/minsoc/branches/ |
| 121 |
Asserting svn:executable properties of modelsim/*.bat scripts.
Including corrected patch for advanced debug system watchpoints under utils/setup. Configure script updated to use this instead of advanced debug system patches. This will remain so until the patch is corrected. The previous line still has the correct command. |
rfajardo |
4562d 05h |
/minsoc/branches/ |
| 120 |
ethmac.prj: a file was missing |
rfajardo |
4562d 08h |
/minsoc/branches/ |
| 119 |
Tricking Subversion to accept bat files that are now executable. |
rfajardo |
4562d 08h |
/minsoc/branches/ |
| 118 |
Configure scripts for Xilinx devices updated. All of them require to update or1200_defines.v. The non-standard part uses now the variable $BOARD to print that this board require non-standard update of files. |
rfajardo |
4562d 08h |
/minsoc/branches/ |
