| Rev |
Log message |
Author |
Age |
Path |
| 128 |
Outsourcing clocks and reset generations from minsoc_bench.v to minsoc_bench_clock.v. |
rfajardo |
4927d 19h |
/minsoc/branches/rc-1.0/ |
| 127 |
Removing redundant simulation output. |
rfajardo |
4928d 01h |
/minsoc/branches/rc-1.0/ |
| 126 |
Updating information about simulation time for Ethernet test. |
rfajardo |
4928d 01h |
/minsoc/branches/rc-1.0/ |
| 125 |
Adjusting testbench messages. Creating tasks for firmware tests. |
rfajardo |
4928d 02h |
/minsoc/branches/rc-1.0/ |
| 124 |
Removing Verilog delays from minsoc_bench.v. minsoc_bench_defines.v defines now if uart or ethernet have to be tested. If yes, it checks the behavior of the enclosed firmwares. If not, simulation simply runs forever. |
rfajardo |
4928d 04h |
/minsoc/branches/rc-1.0/ |
| 123 |
Renaming reg final to firmware_size. Final is a keyword for Verilator. |
rfajardo |
4928d 08h |
/minsoc/branches/rc-1.0/ |
| 122 |
Renaming minsoc-configure.sh to minsoc-setup.sh. |
rfajardo |
4933d 22h |
/minsoc/branches/rc-1.0/ |
| 121 |
Asserting svn:executable properties of modelsim/*.bat scripts.
Including corrected patch for advanced debug system watchpoints under utils/setup. Configure script updated to use this instead of advanced debug system patches. This will remain so until the patch is corrected. The previous line still has the correct command. |
rfajardo |
4933d 23h |
/minsoc/branches/rc-1.0/ |
| 120 |
ethmac.prj: a file was missing |
rfajardo |
4934d 02h |
/minsoc/branches/rc-1.0/ |
| 119 |
Tricking Subversion to accept bat files that are now executable. |
rfajardo |
4934d 03h |
/minsoc/branches/rc-1.0/ |
| 118 |
Configure scripts for Xilinx devices updated. All of them require to update or1200_defines.v. The non-standard part uses now the variable $BOARD to print that this board require non-standard update of files. |
rfajardo |
4934d 03h |
/minsoc/branches/rc-1.0/ |
| 117 |
spartan3e_starter_kit designs require DUALPORT from or1200_defines.v to be active instead of GENERIC. |
rfajardo |
4934d 04h |
/minsoc/branches/rc-1.0/ |
| 116 |
Configure scripts were trying to copy/patch projects files before creating them. Ordering is correct now. |
rfajardo |
4934d 04h |
/minsoc/branches/rc-1.0/ |
| 115 |
configure.sh script dir aware.
minsoc-install.sh logging to script dir. |
rfajardo |
4934d 05h |
/minsoc/branches/rc-1.0/ |
| 114 |
Installation and Configuration scripts can be run out of any directory.
They assume they are going to process the files and directories found in the directory they are run from. |
rfajardo |
4934d 05h |
/minsoc/branches/rc-1.0/ |
| 113 |
minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error
spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated
prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files |
rfajardo |
4934d 05h |
/minsoc/branches/rc-1.0/ |
| 112 |
Updating installation & configuration scripts. |
rfajardo |
4934d 20h |
/minsoc/branches/rc-1.0/ |
| 111 |
minsoc-install.sh: DIR_TO_INSTALL is required before using beautify.sh |
rfajardo |
4934d 21h |
/minsoc/branches/rc-1.0/ |
| 110 |
Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure
-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0
-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.
-prj/src: or1200_top.prj downdated to definition of or1200_v1 |
rfajardo |
4934d 21h |
/minsoc/branches/rc-1.0/ |
| 109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4934d 23h |
/minsoc/branches/rc-1.0/ |
| 108 |
Scripts updates to correct paths when working under Windows. Now, ModelSim, Xilinx and Altera synthesis are working on Windows through batch files.
Icarus Verilog and Altera synthesis are working as well. Job done! |
rfajardo |
4935d 02h |
/minsoc/trunk/ |
| 107 |
Adding setup batch script for Altera synthesis on Windows.
prj/scripts/altprj.sh has now to check if it is run from cygwin in order to re-formulate the path to windows system.
Maybe the other scripts have to be updated too. This will be checked soon. |
rfajardo |
4935d 05h |
/minsoc/trunk/ |
| 106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4935d 08h |
/minsoc/trunk/ |
| 105 |
Updating configure scripts to copy Windows synthesis launch script setup.bat from either minsoc/syn/altera or minsoc/syn/xilinx to minsoc/syn. |
rfajardo |
4935d 10h |
/minsoc/trunk/ |
| 104 |
Enabling modelsim simulation for current project definition.
vhdl and verilog projects have to be separated:
-prj/Makefile defines VHDL_PROJECTS and VERILOG_PROJECTS, they are merged into PROJECTS. Tools which don't care about VHDL or Verilog use PROJECTS list while other tools use VERILOG_ or VHDL_PROJECTS.
-Simulation uses VHDL_PROJECTS and VERILOG_PROJECTS independently.
-prj/scripts/simprj.sh splitted in:
-simvhdl.sh
-simverilog.sh
(they generate the input files in the right format for simulation tools) |
rfajardo |
4942d 09h |
/minsoc/trunk/ |
| 103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4945d 00h |
/minsoc/trunk/ |
| 102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4945d 00h |
/minsoc/trunk/ |
| 101 |
Documentation, wiki's address updated. |
rfajardo |
4970d 12h |
/minsoc/trunk/ |
| 100 |
syn/altera/minsoc_top.qsf: I thought this file was being generated now as project file description. But it is merely a synthesis configuration file and must be here. File re-added. |
rfajardo |
4979d 10h |
/minsoc/trunk/ |
| 99 |
backend/altera_3c25_board/minsoc_defines.v: if GENERIC_FPGA selected, undefine ALTERA_FPGA and FPGA_FAMILY to avoid vendor specific code to flow into the simulation. If you don't do it, generate_bench fails. |
rfajardo |
4979d 10h |
/minsoc/trunk/ |
