OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [branches/] [rc-1.0/] [backend/] - Rev 134

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
124 Removing Verilog delays from minsoc_bench.v. minsoc_bench_defines.v defines now if uart or ethernet have to be tested. If yes, it checks the behavior of the enclosed firmwares. If not, simulation simply runs forever. rfajardo 4530d 15h /minsoc/branches/rc-1.0/backend/
118 Configure scripts for Xilinx devices updated. All of them require to update or1200_defines.v. The non-standard part uses now the variable $BOARD to print that this board require non-standard update of files. rfajardo 4536d 14h /minsoc/branches/rc-1.0/backend/
117 spartan3e_starter_kit designs require DUALPORT from or1200_defines.v to be active instead of GENERIC. rfajardo 4536d 15h /minsoc/branches/rc-1.0/backend/
116 Configure scripts were trying to copy/patch projects files before creating them. Ordering is correct now. rfajardo 4536d 16h /minsoc/branches/rc-1.0/backend/
113 minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error

spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated

prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files
rfajardo 4536d 17h /minsoc/branches/rc-1.0/backend/
110 Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure

-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0

-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.

-prj/src: or1200_top.prj downdated to definition of or1200_v1
rfajardo 4537d 09h /minsoc/branches/rc-1.0/backend/
109 Creating a branche for release candidate 1.0. rfajardo 4537d 11h /minsoc/branches/rc-1.0/backend/
105 Updating configure scripts to copy Windows synthesis launch script setup.bat from either minsoc/syn/altera or minsoc/syn/xilinx to minsoc/syn. rfajardo 4537d 21h /minsoc/trunk/backend/
99 backend/altera_3c25_board/minsoc_defines.v: if GENERIC_FPGA selected, undefine ALTERA_FPGA and FPGA_FAMILY to avoid vendor specific code to flow into the simulation. If you don't do it, generate_bench fails. rfajardo 4581d 21h /minsoc/trunk/backend/
97 As proposed by Javier Almansa automatically generated project files for simulation and synthesis are out of revision control. Instead, the backend configure scripts run the prj/Makefile now to generate the project files prior to configuration of SoC for a specific board. rfajardo 4581d 22h /minsoc/trunk/backend/
96 Some files needed for Altera synthesis javieralso 4582d 08h /minsoc/trunk/backend/
95 Makefile for Altera FPGAs fixed javieralso 4583d 12h /minsoc/trunk/backend/
93 Support for Altera synthesis. It needs some tune, but it works fine javieralso 4585d 23h /minsoc/trunk/backend/
92 backend/spartan3e_starter_kit*: or1200_defines.v file was outdated and hindering synthesis. Probably it would be best if we used a patching system here. But for now, I copied the new files and made the necessary changes to fit the system into the target boards. rfajardo 4586d 21h /minsoc/trunk/backend/
88 Project structure, Xilinx Makefiles and simulation working. rfajardo 4587d 14h /minsoc/trunk/backend/
87 Synchronizing scripts to behave exactly the same. rfajardo 4587d 15h /minsoc/trunk/backend/
86 Updating configure script messages. rfajardo 4587d 15h /minsoc/trunk/backend/
85 Central project definition under prj. Synthesis and simulation take their project files from here. rfajardo 4587d 15h /minsoc/trunk/backend/
80 Establishing a better Makefile system for firmwares. rfajardo 4605d 19h /minsoc/trunk/backend/
70 Including a global timescale under minsoc/rtl/verilog to control simulation. It is under the implementation because the implementation files include it.

Removing timescale definition of minsoc_bench_defines.v files.

Creating a modelsim simulation directory. Everything is working under Linux. For Windows, run_sim.sh has to be changed:
-pli ../../bench/verilog/vpi/jp-io-vpi.so
to:
-pli ../../bench/verilog/vpi/jp-io-vpi.dll

These files have to be compiled/copied from minsoc/rtl/verilog/adv_debug_sys/Software/adv_jtag_bridge/sim_lib/modelsim_platform to minsoc/bench/verilog/vpi.
rfajardo 4706d 20h /minsoc/trunk/backend/
69 backend update:
-minsoc_bench_defines.v
-gcc-opt.mk
Both files should now be under minsoc/backend to proper system functionality.
backend subdirectories have been given those files. Configure script updated accordingly.

They are searched there from system scripts and Makefiles.
-sim/bin/minsoc_verilog_files.txt has the files for Icarus Verilog, minsoc_bench_defines.v is now referenced from backend directory.
-sw/support/Makefile.inc now references to gcc-opt.mk inside backend.

backend/spartan3e_starter_kit_eth:
-It is the system configuration for Spartan 3E Starter Kit with Ethernet.
rfajardo 4711d 12h /minsoc/trunk/backend/
68 Still one configuration mismatch on minsoc_defines.v:
-MEMORY_ADR_WIDTH now 15
-orp.ld is defined accordingly
rfajardo 4713d 16h /minsoc/trunk/backend/
67 Constraint file for backend spartan3a_dsp_kit.ucf was configured to include the STARTUP module.

This module is not enabled under the respective minsoc_defines.v. Thus, its pins had to be commented out.
rfajardo 4713d 16h /minsoc/trunk/backend/
66 spartan3e_starter_kit requires special configuration of or1200_r3.

For that, configure script was specially adapted and that is reported on script execution.

For release-1.0 of MinSoC this should not be required, because or1200_r1 already has the
required configuration.
rfajardo 4713d 17h /minsoc/trunk/backend/
65 Files missing in the last commit.
backend/std/configure
sw: eth, uart and driver Makefiles
rfajardo 4713d 18h /minsoc/trunk/backend/
64 firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.

Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure

backend/spartan3a_dsp_kit:
-working on FPGA

backend/spartan3e_starter_kit:
-has to be tested

backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted

backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable
rfajardo 4713d 20h /minsoc/trunk/backend/
63 Adding a functional synthesis Makefile system. Still needs a reviews and enhancements, but at least it is something. rfajardo 4717d 13h /minsoc/trunk/backend/
40 Commiting a contributions directory, which has raw contributions of users. These contributions still have to be adapted to the system in order to work well. However, some users are certainly able to work with these versions.

FAQ: -added new idea to circumvent onboard DLC9 cable problem for adv_jtag_bridge
INSTALL: -gives a hint on how to install the system for Windows
HOWTO: -explains what a ucf file is and how to create it

backend: now we have the first contribution of a ucf file for the ML509 board (thanks to Matthew Hick)

Documentation: THESIS.txt explains to users, willing to tweak/understand the inner behavior of the OR1200 implementation of OpenRISC, what to read in order to get this information.
rfajardo 4768d 15h /minsoc/trunk/backend/
15 Including verified pinout for external spi flash on spartan3a dsp kit to its correspondent ucf constraint file. rfajardo 5251d 13h /minsoc/trunk/backend/
13 Updating spartan3e_starter_kit.ucf so that it does not deliver errors on mapping. Moreover it has been changed to off the shelf only have uart support. Ethernet support and generic JTAG can be added by uncommenting the corresponding lines. rfajardo 5260d 21h /minsoc/trunk/backend/

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.