OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [branches/] [rc-1.0/] [backend/] [altera_3c25_board/] - Rev 147

Rev

Filtering Options

Clear current filter

Rev Log message Author Age Path
147 Updating minsoc_bench.v to correctly acquire uart data.

Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.

Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT

run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.

minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run.
rfajardo 4727d 17h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
143 Compiling firmwares in board configuration scripts instead of on global minsoc setup. rfajardo 4728d 18h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
124 Removing Verilog delays from minsoc_bench.v. minsoc_bench_defines.v defines now if uart or ethernet have to be tested. If yes, it checks the behavior of the enclosed firmwares. If not, simulation simply runs forever. rfajardo 4748d 14h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
116 Configure scripts were trying to copy/patch projects files before creating them. Ordering is correct now. rfajardo 4754d 14h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
110 Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure

-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0

-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.

-prj/src: or1200_top.prj downdated to definition of or1200_v1
rfajardo 4755d 07h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
109 Creating a branche for release candidate 1.0. rfajardo 4755d 09h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
105 Updating configure scripts to copy Windows synthesis launch script setup.bat from either minsoc/syn/altera or minsoc/syn/xilinx to minsoc/syn. rfajardo 4755d 20h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
99 backend/altera_3c25_board/minsoc_defines.v: if GENERIC_FPGA selected, undefine ALTERA_FPGA and FPGA_FAMILY to avoid vendor specific code to flow into the simulation. If you don't do it, generate_bench fails. rfajardo 4799d 20h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
97 As proposed by Javier Almansa automatically generated project files for simulation and synthesis are out of revision control. Instead, the backend configure scripts run the prj/Makefile now to generate the project files prior to configuration of SoC for a specific board. rfajardo 4799d 20h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
96 Some files needed for Altera synthesis javieralso 4800d 07h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
95 Makefile for Altera FPGAs fixed javieralso 4801d 10h /minsoc/branches/rc-1.0/backend/altera_3c25_board/
93 Support for Altera synthesis. It needs some tune, but it works fine javieralso 4803d 21h /minsoc/branches/rc-1.0/backend/altera_3c25_board/

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.