| Rev |
Log message |
Author |
Age |
Path |
| 152 |
Roll back to retrieve minsoc from branches/rc-1.0. |
rfajardo |
4318d 00h |
/minsoc/branches/rc-1.0/utils/ |
| 150 |
Updating installation script to retrieve minsoc from tags/release-1.0. |
rfajardo |
4318d 00h |
/minsoc/branches/rc-1.0/utils/ |
| 147 |
Updating minsoc_bench.v to correctly acquire uart data.
Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.
Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT
run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.
minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run. |
rfajardo |
4322d 22h |
/minsoc/branches/rc-1.0/utils/ |
| 143 |
Compiling firmwares in board configuration scripts instead of on global minsoc setup. |
rfajardo |
4323d 23h |
/minsoc/branches/rc-1.0/utils/ |
| 138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4324d 13h |
/minsoc/branches/rc-1.0/utils/ |
| 136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4331d 19h |
/minsoc/branches/rc-1.0/utils/ |
| 122 |
Renaming minsoc-configure.sh to minsoc-setup.sh. |
rfajardo |
4349d 13h |
/minsoc/branches/rc-1.0/utils/ |
| 121 |
Asserting svn:executable properties of modelsim/*.bat scripts.
Including corrected patch for advanced debug system watchpoints under utils/setup. Configure script updated to use this instead of advanced debug system patches. This will remain so until the patch is corrected. The previous line still has the correct command. |
rfajardo |
4349d 15h |
/minsoc/branches/rc-1.0/utils/ |
| 115 |
configure.sh script dir aware.
minsoc-install.sh logging to script dir. |
rfajardo |
4349d 20h |
/minsoc/branches/rc-1.0/utils/ |
| 114 |
Installation and Configuration scripts can be run out of any directory.
They assume they are going to process the files and directories found in the directory they are run from. |
rfajardo |
4349d 20h |
/minsoc/branches/rc-1.0/utils/ |
| 113 |
minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error
spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated
prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files |
rfajardo |
4349d 21h |
/minsoc/branches/rc-1.0/utils/ |
| 112 |
Updating installation & configuration scripts. |
rfajardo |
4350d 12h |
/minsoc/branches/rc-1.0/utils/ |
| 111 |
minsoc-install.sh: DIR_TO_INSTALL is required before using beautify.sh |
rfajardo |
4350d 13h |
/minsoc/branches/rc-1.0/utils/ |
| 110 |
Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure
-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0
-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.
-prj/src: or1200_top.prj downdated to definition of or1200_v1 |
rfajardo |
4350d 13h |
/minsoc/branches/rc-1.0/utils/ |
| 109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4350d 15h |
/minsoc/branches/rc-1.0/utils/ |
| 106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4351d 00h |
/minsoc/trunk/utils/ |
| 103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4360d 15h |
/minsoc/trunk/utils/ |
| 102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4360d 15h |
/minsoc/trunk/utils/ |
| 83 |
minsoc-install.sh: bzip2 program was being used, but its existance on target system was not being verified. It is now. |
rfajardo |
4413d 01h |
/minsoc/trunk/utils/ |
| 82 |
minsoc-install.sh: problems with copying the GNU Toolchain from download to tools. We uncompress the GNU Toolchain now once again to tools during the installation part. |
rfajardo |
4416d 00h |
/minsoc/trunk/utils/ |
| 81 |
Installation script complete, nice text feedback, output logs and better execution order. |
rfajardo |
4416d 11h |
/minsoc/trunk/utils/ |
| 79 |
minsoc-install.sh: rpath corrected.
required-cygwin-tools: updated |
rfajardo |
4419d 16h |
/minsoc/trunk/utils/ |
| 78 |
minsoc-install.sh: Advanced JTAG bridge compilation needs to know where the dynamic libraries are on runtime. Patching (sed) the Makefile to compile it with the rpath to the libraries (libusb/libftdi). |
rfajardo |
4419d 16h |
/minsoc/trunk/utils/ |
| 77 |
New tool requirements for installing Icarus Verilog. |
rfajardo |
4419d 17h |
/minsoc/trunk/utils/ |
| 76 |
Including a script allowing the installation of MinSoC and all its required tools.
It should be working for all Linuxes and Cygwin. |
rfajardo |
4419d 17h |
/minsoc/trunk/utils/ |
| 64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4526d 23h |
/minsoc/trunk/utils/ |
| 47 |
Firmware updated to work with gcc-4.5. It is actually working just fine and gcc-4.5 assembly code seems a lot cleaner.
I noticed that by increasing the free stack space for the interrupt handler by 130 made the resulting firmware not work. I assume it is because 130 is not aligned 130%4 = 2 and the stack simply does not work then. Instead I'm freeing the previous 116 plus 128 (for 32 registers as mentioned by Jeremy) and it works. |
rfajardo |
4569d 20h |
/minsoc/trunk/utils/ |
| 46 |
Including an explanation of what has to be updated on gpio to port it smoothly to minsoc. |
rfajardo |
4570d 00h |
/minsoc/trunk/utils/ |
| 45 |
A more stable version |
ConX. |
4570d 15h |
/minsoc/trunk/utils/ |
| 44 |
Fixing some bugs. But it still works only in Debian/Ubuntu |
ConX. |
4570d 17h |
/minsoc/trunk/utils/ |
