OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [branches/] [rc-1.0/] [utils/] [setup/] - Rev 147

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
147 Updating minsoc_bench.v to correctly acquire uart data.

Uart drivers: when an end of line character was sent, the driver appended a carriage return to it. This is not necessary and has been removed.
-Eth and Uart firmwares also had a carriage return after the end of line, also removed.

Minsoc_bench_defines.v: Renaming VCD_OUTPUT define to WAVEFORM_OUTPUT

run_bench: selecting -lxt2 for waveform output format. This output format size is 10 times smaller than vcd.

minsoc-install.sh: lxt2 output format requires that Icarus Verilog be installed with zlib support. For that, we now check if zlib is supported on script run.
rfajardo 4509d 11h /minsoc/branches/rc-1.0/utils/setup/
143 Compiling firmwares in board configuration scripts instead of on global minsoc setup. rfajardo 4510d 12h /minsoc/branches/rc-1.0/utils/setup/
138 DIR_TO_INSTALL creation using wizard ConX. 4511d 02h /minsoc/branches/rc-1.0/utils/setup/
136 Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. rfajardo 4518d 08h /minsoc/branches/rc-1.0/utils/setup/
122 Renaming minsoc-configure.sh to minsoc-setup.sh. rfajardo 4536d 02h /minsoc/branches/rc-1.0/utils/setup/
121 Asserting svn:executable properties of modelsim/*.bat scripts.

Including corrected patch for advanced debug system watchpoints under utils/setup. Configure script updated to use this instead of advanced debug system patches. This will remain so until the patch is corrected. The previous line still has the correct command.
rfajardo 4536d 04h /minsoc/branches/rc-1.0/utils/setup/
115 configure.sh script dir aware.
minsoc-install.sh logging to script dir.
rfajardo 4536d 09h /minsoc/branches/rc-1.0/utils/setup/
114 Installation and Configuration scripts can be run out of any directory.
They assume they are going to process the files and directories found in the directory they are run from.
rfajardo 4536d 09h /minsoc/branches/rc-1.0/utils/setup/
113 minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error

spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated

prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files
rfajardo 4536d 09h /minsoc/branches/rc-1.0/utils/setup/
112 Updating installation & configuration scripts. rfajardo 4537d 00h /minsoc/branches/rc-1.0/utils/setup/
111 minsoc-install.sh: DIR_TO_INSTALL is required before using beautify.sh rfajardo 4537d 01h /minsoc/branches/rc-1.0/utils/setup/
110 Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure

-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0

-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.

-prj/src: or1200_top.prj downdated to definition of or1200_v1
rfajardo 4537d 02h /minsoc/branches/rc-1.0/utils/setup/
109 Creating a branche for release candidate 1.0. rfajardo 4537d 03h /minsoc/branches/rc-1.0/utils/setup/
106 Installation script was checking the ENV variable before setting it. rfajardo 4537d 12h /minsoc/branches/rc-1.0/utils/setup/
103 But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. rfajardo 4547d 04h /minsoc/branches/rc-1.0/utils/setup/
102 GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. rfajardo 4547d 04h /minsoc/branches/rc-1.0/utils/setup/
83 minsoc-install.sh: bzip2 program was being used, but its existance on target system was not being verified. It is now. rfajardo 4599d 14h /minsoc/branches/rc-1.0/utils/setup/
82 minsoc-install.sh: problems with copying the GNU Toolchain from download to tools. We uncompress the GNU Toolchain now once again to tools during the installation part. rfajardo 4602d 13h /minsoc/branches/rc-1.0/utils/setup/
81 Installation script complete, nice text feedback, output logs and better execution order. rfajardo 4603d 00h /minsoc/branches/rc-1.0/utils/setup/
79 minsoc-install.sh: rpath corrected.
required-cygwin-tools: updated
rfajardo 4606d 05h /minsoc/branches/rc-1.0/utils/setup/
78 minsoc-install.sh: Advanced JTAG bridge compilation needs to know where the dynamic libraries are on runtime. Patching (sed) the Makefile to compile it with the rpath to the libraries (libusb/libftdi). rfajardo 4606d 05h /minsoc/branches/rc-1.0/utils/setup/
77 New tool requirements for installing Icarus Verilog. rfajardo 4606d 05h /minsoc/branches/rc-1.0/utils/setup/
76 Including a script allowing the installation of MinSoC and all its required tools.

It should be working for all Linuxes and Cygwin.
rfajardo 4606d 06h /minsoc/branches/rc-1.0/utils/setup/

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.