| Rev |
Log message |
Author |
Age |
Path |
| 153 |
Updating installation script to download minsoc from this branche, verilator, instead of rc-1.0. |
rfajardo |
4757d 22h |
/minsoc/branches/verilator/utils/ |
| 139 |
Creating a verilator branche. |
rfajardo |
4763d 23h |
/minsoc/branches/verilator/utils/ |
| 138 |
DIR_TO_INSTALL creation using wizard |
ConX. |
4764d 11h |
/minsoc/branches/rc-1.0/utils/ |
| 136 |
Installation on Ubuntu-11.10 has shown that a binary called makeinfo is required to install GDB. This binary can be installed on Ubuntu by installing the package texinfo. |
rfajardo |
4771d 18h |
/minsoc/branches/rc-1.0/utils/ |
| 122 |
Renaming minsoc-configure.sh to minsoc-setup.sh. |
rfajardo |
4789d 12h |
/minsoc/branches/rc-1.0/utils/ |
| 121 |
Asserting svn:executable properties of modelsim/*.bat scripts.
Including corrected patch for advanced debug system watchpoints under utils/setup. Configure script updated to use this instead of advanced debug system patches. This will remain so until the patch is corrected. The previous line still has the correct command. |
rfajardo |
4789d 13h |
/minsoc/branches/rc-1.0/utils/ |
| 115 |
configure.sh script dir aware.
minsoc-install.sh logging to script dir. |
rfajardo |
4789d 19h |
/minsoc/branches/rc-1.0/utils/ |
| 114 |
Installation and Configuration scripts can be run out of any directory.
They assume they are going to process the files and directories found in the directory they are run from. |
rfajardo |
4789d 19h |
/minsoc/branches/rc-1.0/utils/ |
| 113 |
minsoc-install.sh & minsoc-configure.sh:
-aware of location of configure.sh script
configure.sh:
-does not block on patch error
spartan3e_starter_kit & spartan3e_starter_kit_eth:
-or1200_defines.v updated
prj:
-src/blackboxes/or1200_top.v adjusted to or1200_rel1
-Makefile had a typo regarding altera vhdl files |
rfajardo |
4789d 19h |
/minsoc/branches/rc-1.0/utils/ |
| 112 |
Updating installation & configuration scripts. |
rfajardo |
4790d 10h |
/minsoc/branches/rc-1.0/utils/ |
| 111 |
minsoc-install.sh: DIR_TO_INSTALL is required before using beautify.sh |
rfajardo |
4790d 11h |
/minsoc/branches/rc-1.0/utils/ |
| 110 |
Fixing several minor issues with the system:
-minsoc-install splitted into installation and configuration
-minsoc-configure.sh can be used to configure a fresh checked out system
-configure script used by both minsoc-configure.sh and minsoc-install.sh to configure
-rtl/verilog: svn externals fixed
-or1200 rolled back to release-1.0
-prj/scripts:
-Makefile has been used by simulation to differentiate project definition of vhdl and verilog files
-Altera was differentiating it in script
-now there are two scripts, one for vhdl and another for verilog. The differentiation occurs in Makefile as for simulation.
-altera_3c25_board/configure scripts had to be updated, vprj and vhdprj file extensions used to differentiate Verilog and VHDL project files.
-prj/src: or1200_top.prj downdated to definition of or1200_v1 |
rfajardo |
4790d 11h |
/minsoc/branches/rc-1.0/utils/ |
| 109 |
Creating a branche for release candidate 1.0. |
rfajardo |
4790d 13h |
/minsoc/branches/rc-1.0/utils/ |
| 106 |
Installation script was checking the ENV variable before setting it. |
rfajardo |
4790d 22h |
/minsoc/trunk/utils/ |
| 103 |
But the file is called gdb-6.8a.tar.bz2, so tar must be run on that name. |
rfajardo |
4800d 13h |
/minsoc/trunk/utils/ |
| 102 |
GNU GDB FTP has renamed gdb-6.8 package to gdb-6.8a package. Uncompressed it remains gdb-6.8, so no other changes to script are necessary. |
rfajardo |
4800d 13h |
/minsoc/trunk/utils/ |
| 83 |
minsoc-install.sh: bzip2 program was being used, but its existance on target system was not being verified. It is now. |
rfajardo |
4852d 23h |
/minsoc/trunk/utils/ |
| 82 |
minsoc-install.sh: problems with copying the GNU Toolchain from download to tools. We uncompress the GNU Toolchain now once again to tools during the installation part. |
rfajardo |
4855d 23h |
/minsoc/trunk/utils/ |
| 81 |
Installation script complete, nice text feedback, output logs and better execution order. |
rfajardo |
4856d 10h |
/minsoc/trunk/utils/ |
| 79 |
minsoc-install.sh: rpath corrected.
required-cygwin-tools: updated |
rfajardo |
4859d 15h |
/minsoc/trunk/utils/ |
| 78 |
minsoc-install.sh: Advanced JTAG bridge compilation needs to know where the dynamic libraries are on runtime. Patching (sed) the Makefile to compile it with the rpath to the libraries (libusb/libftdi). |
rfajardo |
4859d 15h |
/minsoc/trunk/utils/ |
| 77 |
New tool requirements for installing Icarus Verilog. |
rfajardo |
4859d 15h |
/minsoc/trunk/utils/ |
| 76 |
Including a script allowing the installation of MinSoC and all its required tools.
It should be working for all Linuxes and Cygwin. |
rfajardo |
4859d 15h |
/minsoc/trunk/utils/ |
| 64 |
firmware makefiles:
-every firmware makefile has now complete dependency. This also includes dependency on files under minsoc/backend (target specific files). That means, that if some target specific header changes, the support library dependent on it will be compiled. That will always happen, even if you compile the uart firmware. In other words, if you want to use uart firmware, you can always simply compile uart by issuing make all. If anything has changed, backend files, support library, drivers, it will update everything for you.
-TODO: dependency can be automatic created by using make together with gcc. Use it instead of declaring all dependencies manually.
Makefile system for synthesis:
-the dependency for every implementation step has been checked and is working fine.
-Makefile plus support files have been moved to minsoc/syn/src
-make usage is still under syn through files generated by backend bashscripts
Backend:
-files under backend are target specific files used for the system to work
-firmware compilation
-system simulation
-system implementation
-This directory is populated by visiting one of its subdirectories and typing ./configure
backend/spartan3a_dsp_kit:
-working on FPGA
backend/spartan3e_starter_kit:
-has to be tested
backend/ml509:
-missing files have to be copied and adapted, configure script has to be copied and adapted
backend/std:
-include files necessary for firmware compilation and system configuration
-it does not include files for synthesis and is not synthesizable |
rfajardo |
4966d 22h |
/minsoc/trunk/utils/ |
| 47 |
Firmware updated to work with gcc-4.5. It is actually working just fine and gcc-4.5 assembly code seems a lot cleaner.
I noticed that by increasing the free stack space for the interrupt handler by 130 made the resulting firmware not work. I assume it is because 130 is not aligned 130%4 = 2 and the stack simply does not work then. Instead I'm freeing the previous 116 plus 128 (for 32 registers as mentioned by Jeremy) and it works. |
rfajardo |
5009d 18h |
/minsoc/trunk/utils/ |
| 46 |
Including an explanation of what has to be updated on gpio to port it smoothly to minsoc. |
rfajardo |
5009d 23h |
/minsoc/trunk/utils/ |
| 45 |
A more stable version |
ConX. |
5010d 14h |
/minsoc/trunk/utils/ |
| 44 |
Fixing some bugs. But it still works only in Debian/Ubuntu |
ConX. |
5010d 15h |
/minsoc/trunk/utils/ |
| 43 |
Making some changes to MinSOC install script |
ConX. |
5011d 12h |
/minsoc/trunk/utils/ |
| 41 |
Including setup scripts to install all required tools to work with minsoc and to download all required sources. Thanks for the contribution of Xanthopoulos Constantinos. |
rfajardo |
5015d 18h |
/minsoc/trunk/utils/ |
