OpenCores
URL https://opencores.org/ocsvn/minsoc/minsoc/trunk

Subversion Repositories minsoc

[/] [minsoc/] [trunk/] [sw/] [uart/] - Rev 62

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
55 Adjusting Makefiles to compile correctly with new firmware updates.

1) except.o not included into libsupport.a.
2) libsupport.a linked to except.o, now in correct order: ld libsupport.a except.o -o executable (not the other way around)
3) int.c was not being compiled because of a #ifdef which is not set anywhere
rfajardo 4725d 20h /minsoc/trunk/sw/uart/
53 Indentation, deleting redundant files and adding externals ConX. 4725d 23h /minsoc/trunk/sw/uart/
39 FAQ:
-Adv_jtag_bridge self test fails?
-included now SoC flow mistakes
-forgetting to upload the bitfile
-leaving clock unconnected
-older information is now under "Known Issues" right below of SoC flow mistakes

Software:
-eth: included eth.h is from drivers and not from this directory. eth.h from this directory is old and has been removed.
-uart: included uart.h is from drivers and not from this directory. uart.h from this directory is old and has been removed.
rfajardo 4832d 11h /minsoc/trunk/sw/uart/
38 Small update to HOWTO: advices now to also include the ucf (pinout) file, for forgetful people :-).

FAQ: Added another option (hint) as a solution for people with on-board Xilinx USB cables, which do not reset.

uart.c: now uses the IRQ line definition instead of the line number directly.
rfajardo 4867d 10h /minsoc/trunk/sw/uart/
36 utils: -adding a 32 to 8 bit Wishbone bridge to connect 8 bit modules to the MinSoC interconnect.
-adding a Linux driver for parallel cables for the adv_jtag_bridge. It circumvents the necessity of privilege to run adv_jtag_bridge with cables xpc3 and xess.

sw/support: support library has been made completely standalone. That means, it is now independent from uClib and/or newlib. Thanks to Wojciech A. Koszek for his contribution on this.

sw/drivers: a driver library has been included, which supply drivers for the OpenRISC timer; and for UART, Ethernet, I2C, and CAN modules from OpenCores.

sw/uart and sw/eth: they don't provide code to control the UART and Ethernet controllers anymore. They use the drivers library instead.

Documentation:
-FAQ extended:
-table of contents
-explanation of how to use the 32 to 8 bit Wishbone bridge
-how to make adv_jtag_bridge work without privilege requirement for xess or xpc3
-explanation of locking problem of xpc_usb cable
-explanation of what to do if the cable is built on-board
-INSTALL:
-patching of gdb only required if version is 6.8, explanation on FAQ now.
-HOWTO:
-instruct to compile drivers library
-remove line numbers information on what to edit, better leave it to be found only by the informed context.
-adv_jtag_bridge execution now without 'sudo'. Note included that 'sudo' is required for Linux and xess or xpc3. Reference to FAQ to avoid this requirement.
rfajardo 4898d 17h /minsoc/trunk/sw/uart/
2 First commit of project. Beta status:
-testbench: working
-firmware: working
-RTL: Working for: Xilinx Spartan-3A DSP Development Kit
rfajardo 5304d 22h /minsoc/trunk/sw/uart/

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.