Subversion Repositories usb_fpga_1_2

/*!

   ZTEX Firmware Kit for EZ-USB Microcontrollers

   Copyright (C) 2009-2010 ZTEX e.K.

   http://www.ztex.de

   This program is free software; you can redistribute it and/or modify

   it under the terms of the GNU General Public License version 3 as

   published by the Free Software Foundation.

   This program is distributed in the hope that it will be useful, but

   WITHOUT ANY WARRANTY; without even the implied warranty of

   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU

   General Public License for more details.

   You should have received a copy of the GNU General Public License

   along with this program; if not, see http://www.gnu.org/licenses/.

!*/

/*

   Configuration macros

*/

#ifndef[ZTEX_CONF_H]

#define[ZTEX_CONF_H]

/*

   Don't expant macros in comments

*/

#define[//][

][#noexpand[!dnapxeon!]//$0!dnapxeon!

]

#define[/*][*/][#noexpand[!dnapxeon!]/*$0*/!dnapxeon!]

/*

   This macro defines the USB Vendor ID and USB Product ID  (not the product ID

   from the ZTEX descriptor). The Vendor ID must be purchased from the USB-IF

   (http://www.usb.org).

   The default vendor ID is the ZTEX vendor ID 0x221A, default product ID is

   0x100 which is assigned to ZTEX modules. These ID's can be shared by many

   differend products which are identified by the product ID of the ZTEX

   descriptor. According to the USB-IF rules these ID's must not be used by

   hardware which is not manufactured by ZTEX. (Of course, this ID's can be

   used during the development process or for internal purposes.)

   Please read the http://www.ztex.de/firmware-kit/usb_ids.e.html for more

   informations about this topic.

   Usage:

        SET_VPID(<Vendor ID>,<Pioduct ID>);

*/

#define[SET_VPID(][,$1);][#define[USB_VENDOR_ID][$0]

#define[USB_PRODUCT_ID][$1]]

SET_VPID(0x221a,0x100);

/*

   This macro is called before FPGA Firmware is reset, e.g. to save some

   settings. After this macro is called the I/O ports are set to default

   states in order to avoid damage during / after the FPGA configuration.

   To append someting to this macro use the follwing definition:

#define[PRE_FPGA_RESET][PRE_FPGA_RESET

...]

*/

#define[PRE_FPGA_RESET][]

/*

   This macro is called after FPGA Firmware has been configured. This is

   usually used to configure the I/O ports.

   To append someting to this macro use the follwing definition:

#define[POST_FW_LOAD][POST_FW_LOAD

...]

*/

#define[POST_FPGA_CONFIG][]

/*

  Add a vedor request for endpoint 0,

   Usage:

     ADD_EP0_VENDOR_REQUEST((<request number>,,<code executed after setup package received>,,<code executed after data package received>''));

   Example:

     ADD_EP0_VENDOR_REQUEST((0x33,,initHSFPGAConfiguration();,,));;

...]

*/

#define[EP0_VENDOR_REQUESTS_SU;][]

#define[EP0_VENDOR_REQUESTS_DAT;][]

#define[ADD_EP0_VENDOR_REQUEST((][,,$1,,$2));;][#define[EP0_VENDOR_REQUESTS_SU;][EP0_VENDOR_REQUESTS_SU;

case $0:

    $1

    break;

]

#define[EP0_VENDOR_REQUESTS_DAT;][EP0_VENDOR_REQUESTS_DAT;

case $0:

    $2

    break;

]]

/*

   Add a vedor command for endpoint 0,

   Usage:

     ADD_EP0_VENDOR_COMMAND((<request number>,,<code executed after setup package received>,,<code executed after data package received>''));

   Example:

     ADD_EP0_VENDOR_COMMAND((0x33,,initHSFPGAConfiguration();,,));;

...]

*/

#define[EP0_VENDOR_COMMANDS_SU;][]

#define[EP0_VENDOR_COMMANDS_DAT;][]

#define[ADD_EP0_VENDOR_COMMAND((][,,$1,,$2));;][#define[EP0_VENDOR_COMMANDS_SU;][EP0_VENDOR_COMMANDS_SU;

case $0:

    $1

    break;

]

#define[EP0_VENDOR_COMMANDS_DAT;][EP0_VENDOR_COMMANDS_DAT;

case $0:

    $2

    break;

]]

/*

  This macro generates a EP0 stall and aborts the current loop. Stalls are usually used to indicate errors.

*/

#define[EP0_STALL;][{

    EP0CS |= 0x01;      // set stall

    ep0_payload_remaining = 0;

    break;

}]

/*

   Endoint 1,2,4,5,8 configuration:

   EP_CONFIG(<EP number>,<interface>,<type>,<direction>,<size>,<buffers>)

        <EP number> = 1IN | 1OUT | 2 | 4 | 6 | 8        Endpoint numer

        <INTERFACE> = 0 | 1 | 2 | 3                     To which interface this endpoint belongs

        <type>      = BULK  | ISO | INT

        <dir>       = IN | OUT

        <size>      = 512 | 1024

        <buffers>   = 1 | 2 | 3 | 4

   Example: EP_CONFIG(2,0,ISO,OUT,1024,4);

   Importand note: No spaces next to the commas

   Endoint 1 configuration:

   These Endpoints are defined by default as bulk endpoints and are assigned to interface 0.

   Endpoint size is always 64 bytes, but reported Endpoint size will be 512 bytes for USB 2.0 compliance.

   These Endpoints can be redefined using EP_CONFIG or using:

   EP1IN_CONFIG(<interface>);

           <INTERFACE> = 0 | 1 | 2 | 3          Interface to which EP1IN belongs; default: 0

   EP1OUT_CONFIG(<interface>);

           <INTERFACE> = 0 | 1 | 2 | 3          Interface to which EP1OUT belongs; default: 0

   EP1_CONFIG(<interface>);

           <INTERFACE> = 0 | 1 | 2 | 3          Interface to which EP1IN and EP1OUT belongs; default: 0

   The following (maximum) configurations are possible:

   EP2          EP4     EP6     EP8

   2x512        2x512   2x512   2x512

   2x512        2x512   4x512

   2x512        2x512   2x1024

   4x512                2x512   2x512

   4x512                4x512

   4x512                2x1024

   2x1024               2x512   2x512

   2x1024               4x512

   2x1024               2x1024

   3x512                3x512   2x512

   3x1024                       2x512

   4x1024

*/

#define[EP_CONFIG(][,$1,$2,$3,$4,$5);][

#ifeq[$0][1IN]

#elifeq[$0][1OUT]

#elifeq[$0][2]

#elifeq[$0][4]

#elifeq[$0][6]

#elifneq[$0][8]

#error[EP_CONFIG: Invalid 1st parameter: `$0'. Expected `2', `4', `6' or '8']

#endif

#ifeq[$1][0]

#elifeq[$1][1]

#elifeq[$1][2]

#elifneq[$1][3]

#error[EP_CONFIG: Invalid 2nd parameter: `$1'. Expected `0', `1', `2' or '3']

#endif

#ifeq[$2][BULK]

#elifeq[$2][ISO]

#elifneq[$2][INT]

#error[EP_CONFIG: Invalid 3nd parameter: `$2'. Expected `BULK', `ISO' or 'INT']

#endif

#ifeq[$3][IN]

#elifneq[$3][OUT]

#error[EP_CONFIG: Invalid 4th parameter: `$3'. Expected `IN' or 'OUT']

#endif

#ifeq[$4][512]

#elifneq[$4][1024]

#error[EP_CONFIG: Invalid 5th parameter: `$4'. Expected `512' or '1024']

#endif

#ifeq[$5][1]

#elifeq[$5][2]

#elifeq[$5][3]

#elifneq[$5][4]

#error[EP_CONFIG: Invalid 6th parameter: `$5'. Expected `1', `2', `3' or `4']

#endif

#define[EP$0_INTERFACE][$1]

#define[EP$0_TYPE][$2]

#define[EP$0_DIR][$3]

#define[EP$0_SIZE][$4]

#define[EP$0_BUFFERS][$5]]

#define[EP1IN_CONFIG(][);][#define[EP1IN_INTERFACE][$0]]

#define[EP1OUT_CONFIG(][);][#define[EP1OUT_INTERFACE][$0]]

#define[EP1_CONFIG(][);][#define[EP1IN_INTERFACE][$0]

#define[EP1OUT_INTERFACE][$0]]

EP_CONFIG(1IN,0,BULK,IN,512,1);

EP_CONFIG(1OUT,0,BULK,OUT,512,1);

/*

   ISO and INT Transactions per microframe:

   Default value is 1 for all endpoints.

   EP_PPMF(<EP number>,<tansactions per microframe>)

        <EP number>                  = 1IN | 1OUT | 2 | 4 | 6 | 8       Endpoint

        <tansactions per microframe> = 1 | 2 | 3                        Transactions per microframe

   Example: EP_PPMF(2,3);

   Importand note: No spaces next to the commas

*/

#define[EP_PPMF(][,$1);][

#ifeq[$0][1IN]

#elifeq[$0][1OUT]

#elifeq[$0][2]

#elifeq[$0][4]

#elifeq[$0][6]

#elifneq[$0][8]

#error[EP_CONFIG: Invalid 1st parameter: `$0'. Expected `1IN', `1OUT', `2', `4', `6' or '8']

#endif

#ifeq[$1][1]

#elifeq[$1][2]

#elifneq[$1][3]

#error[EP_CONFIG: Invalid 2nd parameter: `$1'. Expected `1', `2' or '3']

#endif

#define[EP$0_PPMF][$1]]

EP_PPMF(1IN,1);

EP_PPMF(1OUT,1);

EP_PPMF(2,1);

EP_PPMF(4,1);

EP_PPMF(6,1);

EP_PPMF(8,1);

/*

   Polling interval in microframes for INT transactions:

   Default value is 1 for all endpoints.

   EP_POLL(<EP number>,<polling interval>)

        <EP number>        = 1IN | 1OUT | 2 | 4 | 6 | 8         Endpoint

        <polling interval> = 1 | 2 | 3                          Polling interval

   Example: EP_POLL(2,1);

   Importand note: No spaces next to the commas

*/

#define[EP_POLL(][,$1);][

#ifeq[$0][1IN]

#elifeq[$0][1OUT]

#elifeq[$0][2]

#elifeq[$0][4]

#elifeq[$0][6]

#elifneq[$0][8]

#error[EP_CONFIG: Invalid 1st parameter: `$0'. Expected `1IN', `1OUT', `2', `4', `6' or '8']

#endif

#define[EP$0_POLL][$1]]

EP_POLL(1IN,1);

EP_POLL(1OUT,1);

EP_POLL(2,1);

EP_POLL(4,1);

EP_POLL(6,1);

EP_POLL(8,1);

/*

   Settings which depends PRODUCT_ID, e.g extra capabilities.

   Overwrite this macros as desired.

*/

#define[MODULE_RESERVED_00][0]

#define[MODULE_RESERVED_01][0]

#define[MODULE_RESERVED_02][0]

#define[MODULE_RESERVED_03][0]

#define[MODULE_RESERVED_04][0]

#define[MODULE_RESERVED_05][0]

#define[MODULE_RESERVED_06][0]

#define[MODULE_RESERVED_07][0]

#define[MODULE_RESERVED_08][0]

#define[MODULE_RESERVED_09][0]

#define[MODULE_RESERVED_10][0]

#define[MODULE_RESERVED_11][0]

#define[FWVER][0]

#define[PRODUCT_ID_0][0]

#define[PRODUCT_ID_1][0]

#define[PRODUCT_ID_2][0]

#define[PRODUCT_ID_3][0]

/*

   Identify as ZTEX USB FPGA Module 1.0

   Usage: IDENTITY_UFM_1_0(<PRODUCT_ID_0>.<PRODUCT_ID_1><PRODUCT_ID_2>.<PRODUCT_ID_3>,<FW_VERSION>);

*/

#define[IDENTITY_UFM_1_0(][.$1.$2.$3,$4);][#define[PRODUCT_ID_0][$0]

#define[PRODUCT_ID_1][$1]

#define[PRODUCT_ID_2][$2]

#define[PRODUCT_ID_3][$3]

#define[FWVER][$4]

#define[PRODUCT_IS][UFM-1_0]

#define[PRODUCT_STRING]["USB-FPGA Module 1.0"]]

/*

   Identify as ZTEX USB FPGA Module 1.1

   Usage: IDENTITY_UFM_1_1(<PRODUCT_ID_0>.<PRODUCT_ID_1><PRODUCT_ID_2>.<PRODUCT_ID_3>,<FW_VERSION>);

*/

#define[IDENTITY_UFM_1_1(][.$1.$2.$3,$4);][#define[PRODUCT_ID_0][$0]

#define[PRODUCT_ID_1][$1]

#define[PRODUCT_ID_2][$2]

#define[PRODUCT_ID_3][$3]

#define[FWVER][$4]

#define[PRODUCT_IS][UFM-1_1]

#define[PRODUCT_STRING]["USB-FPGA Module 1.1"]]

/*

   Identify as ZTEX USB FPGA Module 1.2

   Usage: IDENTITY_UFM_1_2(<PRODUCT_ID_0>.<PRODUCT_ID_1><PRODUCT_ID_2>.<PRODUCT_ID_3>,<FW_VERSION>);

*/

#define[IDENTITY_UFM_1_2(][.$1.$2.$3,$4);][#define[PRODUCT_ID_0][$0]

#define[PRODUCT_ID_1][$1]

#define[PRODUCT_ID_2][$2]

#define[PRODUCT_ID_3][$3]

#define[FWVER][$4]

#define[PRODUCT_IS][UFM-1_2]

#define[PRODUCT_STRING]["USB-FPGA Module 1.2"]]

/*

   Identify as ZTEX USB FPGA Module 1.10

   Usage: IDENTITY_UFM_1_10(<PRODUCT_ID_0>.<PRODUCT_ID_1><PRODUCT_ID_2>.<PRODUCT_ID_3>,<FW_VERSION>);

*/

#define[IDENTITY_UFM_1_10(][.$1.$2.$3,$4);][#define[PRODUCT_ID_0][$0]

#define[PRODUCT_ID_1][$1]

#define[PRODUCT_ID_2][$2]

#define[PRODUCT_ID_3][$3]

#define[FWVER][$4]

#define[PRODUCT_IS][UFM-1_10]

#define[PRODUCT_STRING]["USB-FPGA Module 1.10"]]

/*

   Identify as ZTEX USB FPGA Module 1.11

   Usage: IDENTITY_UFM_1_10(<PRODUCT_ID_0>.<PRODUCT_ID_1><PRODUCT_ID_2>.<PRODUCT_ID_3>,<FW_VERSION>);

*/

#define[IDENTITY_UFM_1_11(][.$1.$2.$3,$4);][#define[PRODUCT_ID_0][$0]

#define[PRODUCT_ID_1][$1]

#define[PRODUCT_ID_2][$2]

#define[PRODUCT_ID_3][$3]

#define[FWVER][$4]

#define[PRODUCT_IS][UFM-1_11]

#define[PRODUCT_STRING]["USB-FPGA Module 1.11"]]

/*

   Identify as ZTEX USB Module 1.0

   Usage: IDENTITY_UM_1_0(<PRODUCT_ID_0>.<PRODUCT_ID_1><PRODUCT_ID_2>.<PRODUCT_ID_3>,<FW_VERSION>);

*/

#define[IDENTITY_UM_1_0(][.$1.$2.$3,$4);][#define[PRODUCT_ID_0][$0]

#define[PRODUCT_ID_1][$1]

#define[PRODUCT_ID_2][$2]

#define[PRODUCT_ID_3][$3]

#define[FWVER][$4]

#define[PRODUCT_IS][UM-1_0]

#define[PRODUCT_STRING]["USB Module 1.0"]]

/*

   This macro defines the Manufacturer string. Limited to 31 charcters.

*/

#define[MANUFACTURER_STRING]["ZTEX"]

/*

   This macro defines the Product string. Limited to 31 charcters.

*/

#define[PRODUCT_STRING]["USB-FPGA Module"]

/*

   This macro defines the Configuration string. Limited to 31 charcters.

*/

#define[CONFIGURATION_STRING]["(unknown)"]

/*

   This macro enables defines the Configuration string. Limited to 31 charcters.

*/

#define[CONFIGURATION_STRING]["(unknown)"]

/*

   This macro disables EEPROM interface and certain I2C functions (enabled by default)

   Usage: DISABLE_EEPROM;

*/

#define[DISBALE_EEPROM;][#define[EEPROM_DISBALED][1]]

/*

   This macro enables the Flash interface, if available

   Usage: ENABLE_FLASH;

*/

#define[ENABLE_FLASH;][#define[FLASH_ENABLED][1]]

/*

   This macro enables the FPGA configuration using a bitstream from the Flash memory

   Usage: ENABLE_FLASH_BITSTREAM;

*/

#define[ENABLE_FLASH_BITSTREAM;][#define[FLASH_BITSTREAM_ENABLED][1]]

#endif