| Line 317... |
Line 317... |
.dmem_wen (dmem_wen), // Data Memory write enable (low active)
|
.dmem_wen (dmem_wen), // Data Memory write enable (low active)
|
.irq_acc (irq_acc), // Interrupt request accepted (one-hot signal)
|
.irq_acc (irq_acc), // Interrupt request accepted (one-hot signal)
|
.lfxt_enable (), // ASIC ONLY: Low frequency oscillator enable
|
.lfxt_enable (), // ASIC ONLY: Low frequency oscillator enable
|
.lfxt_wkup (), // ASIC ONLY: Low frequency oscillator wake-up (asynchronous)
|
.lfxt_wkup (), // ASIC ONLY: Low frequency oscillator wake-up (asynchronous)
|
.mclk (mclk), // Main system clock
|
.mclk (mclk), // Main system clock
|
|
.dma_dout (), // Direct Memory Access data output
|
|
.dma_ready (), // Direct Memory Access is complete
|
|
.dma_resp (), // Direct Memory Access response (0:Okay / 1:Error)
|
.per_addr (per_addr), // Peripheral address
|
.per_addr (per_addr), // Peripheral address
|
.per_din (per_din), // Peripheral data input
|
.per_din (per_din), // Peripheral data input
|
.per_we (per_we), // Peripheral write enable (high active)
|
|
.per_en (per_en), // Peripheral enable (high active)
|
.per_en (per_en), // Peripheral enable (high active)
|
|
.per_we (per_we), // Peripheral write enable (high active)
|
.pmem_addr (pmem_addr), // Program Memory address
|
.pmem_addr (pmem_addr), // Program Memory address
|
.pmem_cen (pmem_cen), // Program Memory chip enable (low active)
|
.pmem_cen (pmem_cen), // Program Memory chip enable (low active)
|
.pmem_din (pmem_din), // Program Memory data input (optional)
|
.pmem_din (pmem_din), // Program Memory data input (optional)
|
.pmem_wen (pmem_wen), // Program Memory write enable (low active) (optional)
|
.pmem_wen (pmem_wen), // Program Memory write enable (low active) (optional)
|
.puc_rst (puc_rst), // Main system reset
|
.puc_rst (puc_rst), // Main system reset
|
| Line 341... |
Line 344... |
.dbg_uart_rxd (uart_rx), // Debug interface: UART RXD (asynchronous)
|
.dbg_uart_rxd (uart_rx), // Debug interface: UART RXD (asynchronous)
|
.dco_clk (dco_clk), // Fast oscillator (fast clock)
|
.dco_clk (dco_clk), // Fast oscillator (fast clock)
|
.dmem_dout (dmem_dout), // Data Memory data output
|
.dmem_dout (dmem_dout), // Data Memory data output
|
.irq (irq_bus), // Maskable interrupts
|
.irq (irq_bus), // Maskable interrupts
|
.lfxt_clk (1'b0), // Low frequency oscillator (typ 32kHz)
|
.lfxt_clk (1'b0), // Low frequency oscillator (typ 32kHz)
|
|
.dma_addr (15'h0000), // Direct Memory Access address
|
|
.dma_din (16'h0000), // Direct Memory Access data input
|
|
.dma_en (1'b0), // Direct Memory Access enable (high active)
|
|
.dma_priority (1'b0), // Direct Memory Access priority (0:low / 1:high)
|
|
.dma_we (2'b00), // Direct Memory Access write byte enable (high active)
|
|
.dma_wkup (1'b0), // ASIC ONLY: DMA Sub-System Wake-up (asynchronous and non-glitchy)
|
.nmi (nmi), // Non-maskable interrupt (asynchronous)
|
.nmi (nmi), // Non-maskable interrupt (asynchronous)
|
.per_dout (per_dout), // Peripheral data output
|
.per_dout (per_dout), // Peripheral data output
|
.pmem_dout (pmem_dout), // Program Memory data output
|
.pmem_dout (pmem_dout), // Program Memory data output
|
.reset_n (reset_n), // Reset Pin (low active, asynchronous and non-glitchy)
|
.reset_n (reset_n), // Reset Pin (low active, asynchronous and non-glitchy)
|
.scan_enable (1'b0), // ASIC ONLY: Scan enable (active during scan shifting)
|
.scan_enable (1'b0), // ASIC ONLY: Scan enable (active during scan shifting)
|
| Line 526... |
Line 535... |
assign led = {cntrl1, p1_dout[0], p1_dout[0], cntrl2};
|
assign led = {cntrl1, p1_dout[0], p1_dout[0], cntrl2};
|
|
|
|
|
endmodule // openMSP430_fpga
|
endmodule // openMSP430_fpga
|
|
|
|
|
No newline at end of file
|
No newline at end of file
|
