Subversion Repositories amber

File in this directory:
initrd                      A disk image needed if you want to build the 
                            Amber Linux kernel from sources
patch-2.4.27-amber2.bz2     Amber Linux patch file
patch-2.4.27-vrs1.bz2       ARM Linux patch file
README.txt                  This file
vmlinux                     Kernel executable file
vmlinux.dis                 Kernel disassembly file
vmlinux.mem                 Kernel .mem file for Verilog simulations
                            If you build the kernal from source these 2 files
                            get replaced.

# +++++++++++++++++++++++++++++++++++++++++++
# How to run Amber Linux kernel on a development board
# +++++++++++++++++++++++++++++++++++++++++++
1. Download the bitfile to configure the FPGA using Impact ir Chipscope
2. Connect HyperTerminal to the serial port on the FPGA to connect to the boot loader
3. Download the disk image
> b 800000
Then select the file $AMBER_BASE/sw/vmlinux/initrd to transfer
4. Download the kernel image
> l
Then select the file $AMBER_BASE/sw/vmlinux/vmlinux to transfer
5. Execute th ekernel
> j


# +++++++++++++++++++++++++++++++++++++++++++
# How to build Amber Linux kernel from source
# +++++++++++++++++++++++++++++++++++++++++++
# If you also want to create your own initrd disk image, 
# then follow that procedure (below) first.

# Set the location on your system where the Amber project is located
export AMBER_BASE=/proj/opencores-svn/trunk

# Pick a directory on your system where you want to build Linux
export LINUX_WORK_DIR=/proj/amber2-linux

export AMBER_CROSSTOOL=arm-none-linux-gnueabi


# Create the Linux build directory
test -e ${LINUX_WORK_DIR} || mkdir ${LINUX_WORK_DIR}
cd ${LINUX_WORK_DIR}

# Download the kernel source
wget http://www.kernel.org/pub/linux/kernel/v2.4/linux-2.4.27.tar.gz
tar zxf linux-2.4.27.tar.gz
ln -s linux-2.4.27 linux
cd linux

#Apply 2 patch files
cp ${AMBER_BASE}/sw/vmlinux/patch-2.4.27-vrs1.bz2 .
cp ${AMBER_BASE}/sw/vmlinux/patch-2.4.27-amber2.bz2 .
bzip2 -d patch-2.4.27-vrs1.bz2
bzip2 -d patch-2.4.27-amber2.bz2
patch -p1 < patch-2.4.27-vrs1
patch -p1 < patch-2.4.27-amber2

# Build the kernel and create a .mem file for simulations
make dep
make vmlinux

cp vmlinux vmlinux_unstripped
${AMBER_CROSSTOOL}-objcopy -R .comment -R .note vmlinux
${AMBER_CROSSTOOL}-objcopy --change-addresses -0x02000000 vmlinux
$AMBER_BASE/sw/tools/amber-elfsplitter vmlinux > vmlinux.mem
# Add the ram disk image to the .mem file
$AMBER_BASE/sw/tools/amber-bin2mem ${AMBER_BASE}/sw/vmlinux/initrd 800000 >> vmlinux.mem
${AMBER_CROSSTOOL}-objdump -C -S -EL vmlinux_unstripped > vmlinux.dis 
cp vmlinux.mem $AMBER_BASE/sw/vmlinux/vmlinux.mem
cp vmlinux.dis $AMBER_BASE/sw/vmlinux/vmlinux.dis

# Run the Linux simulation to verify that you have a good kernel image
cd $AMBER_BASE/hw/sim
run vmlinux


# +++++++++++++++++++++++++++++++++++++++++++
# How to create your own initrd file
# +++++++++++++++++++++++++++++++++++++++++++
This file is the disk image that Linux mounts as
part of the boot process. It contains a bare bones Linux directory
structure and an init file (which is just hello-world renamed).

# Set the location on your system where the Amber project is located
export AMBER_BASE=/proj/opencores-svn/trunk

# Pick a directory on your system where you want to build Linux
export LINUX_WORK_DIR=/proj/amber2-linux


cd ${LINUX_WORK_DIR}
# Need root permissions to mount disks
su root
dd if=/dev/zero of=initrd bs=200k count=1
mke2fs -F -m0 -b 1024 initrd

mkdir mnt
mount -t ext2 -o loop initrd ${LINUX_WORK_DIR}/mnt

# Add files 
mkdir ${LINUX_WORK_DIR}/mnt/sbin
mkdir ${LINUX_WORK_DIR}/mnt/dev
mkdir ${LINUX_WORK_DIR}/mnt/bin
mkdir ${LINUX_WORK_DIR}/mnt/etc
mkdir ${LINUX_WORK_DIR}/mnt/proc
mkdir ${LINUX_WORK_DIR}/mnt/lib

mknod ${LINUX_WORK_DIR}/mnt/dev/console c 5 1
mknod ${LINUX_WORK_DIR}/mnt/dev/tty2 c 4 2
mknod ${LINUX_WORK_DIR}/mnt/dev/null c 1 3
mknod ${LINUX_WORK_DIR}/mnt/dev/loop0 b 7 0
chmod 600 ${LINUX_WORK_DIR}/mnt/dev/*

cp $AMBER_BASE/sw/hello-world/hello-world.flt ${LINUX_WORK_DIR}/mnt/sbin/init
chmod +x ${LINUX_WORK_DIR}/mnt/sbin/init

# Check
df ${LINUX_WORK_DIR}/mnt

# Unmount
umount ${LINUX_WORK_DIR}/mnt
rm -rf ${LINUX_WORK_DIR}/mnt
exit

cp initrd $AMBER_BASE/sw/vmlinux