Subversion Repositories pcie_sg_dma

 
//-----------------------------------------------------------------------------
//
// (c) Copyright 2009-2011 Xilinx, Inc. All rights reserved.
//
// This file contains confidential and proprietary information
// of Xilinx, Inc. and is protected under U.S. and
// international copyright and other intellectual property
// laws.
//
// DISCLAIMER
// This disclaimer is not a license and does not grant any
// rights to the materials distributed herewith. Except as
// otherwise provided in a valid license issued to you by
// Xilinx, and to the maximum extent permitted by applicable
// law: (1) THESE MATERIALS ARE MADE AVAILABLE "AS IS" AND
// WITH ALL FAULTS, AND XILINX HEREBY DISCLAIMS ALL WARRANTIES
// AND CONDITIONS, EXPRESS, IMPLIED, OR STATUTORY, INCLUDING
// BUT NOT LIMITED TO WARRANTIES OF MERCHANTABILITY, NON-
// INFRINGEMENT, OR FITNESS FOR ANY PARTICULAR PURPOSE; and
// (2) Xilinx shall not be liable (whether in contract or tort,
// including negligence, or under any other theory of
// liability) for any loss or damage of any kind or nature
// related to, arising under or in connection with these
// materials, including for any direct, or any indirect,
// special, incidental, or consequential loss or damage
// (including loss of data, profits, goodwill, or any type of
// loss or damage suffered as a result of any action brought
// by a third party) even if such damage or loss was
// reasonably foreseeable or Xilinx had been advised of the
// possibility of the same.
//
// CRITICAL APPLICATIONS
// Xilinx products are not designed or intended to be fail-
// safe, or for use in any application requiring fail-safe
// performance, such as life-support or safety devices or
// systems, Class III medical devices, nuclear facilities,
// applications related to the deployment of airbags, or any
// other applications that could lead to death, personal
// injury, or severe property or environmental damage
// (individually and collectively, "Critical
// Applications"). Customer assumes the sole risk and
// liability of any use of Xilinx products in Critical
// Applications, subject only to applicable laws and
// regulations governing limitations on product liability.
//
// THIS COPYRIGHT NOTICE AND DISCLAIMER MUST BE RETAINED AS
// PART OF THIS FILE AT ALL TIMES.
//
//-----------------------------------------------------------------------------
// Project    : Virtex-6 Integrated Block for PCI Express
// File       : pcie_brams_v6.v
// Version    : 1.7
//--
//-- Description: BlockRAM module for Virtex6 PCIe Block
//--
//--
//--
//--------------------------------------------------------------------------------
 
`timescale 1ns/1ns
 
module pcie_brams_v6
#(
   // the number of BRAMs to use
   // supported values are:
   // 1,2,4,8,18
   parameter NUM_BRAMS               = 0,
 
   // BRAM read address latency
   //
   // value     meaning
   // ====================================================
   //   0       BRAM read address port sample
   //   1       BRAM read address port sample and a pipeline stage on the address port
   parameter RAM_RADDR_LATENCY   = 1,
 
   // BRAM read data latency
   //
   // value     meaning
   // ====================================================
   //   1       no BRAM OREG
   //   2       use BRAM OREG
   //   3       use BRAM OREG and a pipeline stage on the data port
   parameter RAM_RDATA_LATENCY   = 1,
 
   // BRAM write latency
   // The BRAM write port is synchronous
   //
   // value     meaning
   // ====================================================
   //   0       BRAM write port sample
   //   1       BRAM write port sample plus pipeline stage
   parameter RAM_WRITE_LATENCY       = 1
 )
  (
   input          user_clk_i,
   input          reset_i,
 
   input          wen,
   input  [12:0]  waddr,
   input  [71:0]  wdata,
   input          ren,
   input          rce,
   input  [12:0]  raddr,
   output [71:0]  rdata
   );
 
   // turn on the bram output register
   localparam DOB_REG = (RAM_RDATA_LATENCY > 1) ? 1 : 0;
 
   // calculate the data width of the individual brams
   localparam [6:0] WIDTH = ((NUM_BRAMS == 1) ? 72 :
                             (NUM_BRAMS == 2) ? 36 :
                             (NUM_BRAMS == 4) ? 18 :
                             (NUM_BRAMS == 8) ?  9 :
                                                 4
                            );
 
   parameter TCQ           = 1;
 
   //synthesis translate_off
   initial begin
      $display("[%t] %m NUM_BRAMS %0d  DOB_REG %0d WIDTH %0d RAM_WRITE_LATENCY %0d RAM_RADDR_LATENCY %0d RAM_RDATA_LATENCY %0d",
                $time, NUM_BRAMS, DOB_REG, WIDTH, RAM_WRITE_LATENCY, RAM_RADDR_LATENCY, RAM_RDATA_LATENCY);
 
      case (NUM_BRAMS)
        1,2,4,8,18:;
        default: 
          begin
             $display("[%t] %m Error NUM_BRAMS %0d not supported", $time, NUM_BRAMS);
             $finish;
          end
      endcase // case(NUM_BRAMS)
 
      case (RAM_RADDR_LATENCY)
        0,1:;
        default: 
          begin 
             $display("[%t] %m Error RAM_READ_LATENCY %0d not supported", $time, RAM_RADDR_LATENCY);
             $finish;
          end
      endcase // case (RAM_RADDR_LATENCY)
 
      case (RAM_RDATA_LATENCY)
        1,2,3:;
        default: 
          begin 
             $display("[%t] %m Error RAM_READ_LATENCY %0d not supported", $time, RAM_RDATA_LATENCY);
             $finish;
          end
      endcase // case (RAM_RDATA_LATENCY)
 
      case (RAM_WRITE_LATENCY)
        0,1:;
        default:
          begin
             $display("[%t] %m Error RAM_WRITE_LATENCY %0d not supported", $time, RAM_WRITE_LATENCY);
             $finish;
          end
      endcase // case(RAM_WRITE_LATENCY)
 
   end
   //synthesis translate_on
 
   // model the delays for ram write latency
 
   wire        wen_int;
   wire [12:0] waddr_int;
   wire [71:0] wdata_int;
 
   generate if (RAM_WRITE_LATENCY == 1) begin : wr_lat_2
      reg        wen_dly;
      reg [12:0] waddr_dly;
      reg [71:0] wdata_dly;
 
      always @(posedge user_clk_i) begin
         if (reset_i) begin
            wen_dly   <= #TCQ 1'b0;
            waddr_dly <= #TCQ 13'b0;
            wdata_dly <= #TCQ 72'b0;
         end else begin
            wen_dly   <= #TCQ wen;
            waddr_dly <= #TCQ waddr;
            wdata_dly <= #TCQ wdata;
         end
      end
 
      assign wen_int   = wen_dly;
      assign waddr_int = waddr_dly;
      assign wdata_int = wdata_dly;
   end // if (RAM_WRITE_LATENCY == 1)
 
   else if (RAM_WRITE_LATENCY == 0) begin : wr_lat_1
      assign wen_int   = wen;
      assign waddr_int = waddr;
      assign wdata_int = wdata;
   end
   endgenerate
 
   // model the delays for ram read latency
 
   wire        ren_int;
   wire [12:0] raddr_int;
   wire [71:0] rdata_int;
 
   generate if (RAM_RADDR_LATENCY == 1) begin : raddr_lat_2
      reg        ren_dly;
      reg [12:0] raddr_dly;
 
      always @(posedge user_clk_i) begin
         if (reset_i) begin
            ren_dly   <= #TCQ 1'b0;
            raddr_dly <= #TCQ 13'b0;
         end else begin
            ren_dly   <= #TCQ ren;
            raddr_dly <= #TCQ raddr;
         end // else: !if(reset_i)
      end
 
      assign ren_int   = ren_dly;
      assign raddr_int = raddr_dly;
   end // block: rd_lat_addr_2
 
   else begin : raddr_lat_1
      assign ren_int   = ren;
      assign raddr_int = raddr;
   end
   endgenerate
 
   generate if (RAM_RDATA_LATENCY == 3) begin : rdata_lat_3
      reg [71:0] rdata_dly;
 
      always @(posedge user_clk_i) begin
         if (reset_i) begin
            rdata_dly <= #TCQ 72'b0;
         end else begin
            rdata_dly <= #TCQ rdata_int;
         end // else: !if(reset_i)
      end
 
      assign rdata     = rdata_dly;
 
   end // block: rd_lat_data_3
 
   else begin : rdata_lat_1_2
      assign #TCQ rdata     = rdata_int;
   end
   endgenerate
 
   // instantiate the brams
   generate
      genvar i;
      for (i = 0; i < NUM_BRAMS; i = i + 1) begin : brams
         pcie_bram_v6 #(.DOB_REG(DOB_REG), .WIDTH(WIDTH))
           ram (.user_clk_i(user_clk_i), .reset_i(reset_i), 
                .wen_i(wen_int), .waddr_i(waddr_int), .wdata_i(wdata_int[(((i + 1) * WIDTH) - 1): (i * WIDTH)]), 
                .ren_i(ren_int), .raddr_i(raddr_int), .rdata_o(rdata_int[(((i + 1) * WIDTH) - 1): (i * WIDTH)]), .rce_i(rce));
      end
   endgenerate
endmodule // pcie_brams_v6