OpenCores
URL https://opencores.org/ocsvn/System09/System09/trunk

Subversion Repositories System09

[/] [System09/] - Rev 209

Rev

Go to most recent revision

Filtering Options

Clear current filter

Rev Log message Author Age Path
209 Started adding in keyboard (not tested).
Added in green-only VGA output thru Pmod port to PmodVGA J2 port.
Started working on HDMI output		 davidgb 1153d 04h /System09/
208 swapped 32k and 16k ram to use block_spram. davidgb 1197d 05h /System09/
207 Updated design to pick up vdu8_spram (which uses parameterized ram for video memory instead of hard macros) davidgb 1197d 06h /System09/
206 Update comment/cleanup davidgb 1197d 06h /System09/
205 A new version of VDU8 that uses the parameterized xilinx ram "block_spram" for the video memory. davidgb 1197d 06h /System09/
204 patched up ram for zybo use davidgb 1197d 06h /System09/
203 Added a parameterized ram model. davidgb 1197d 06h /System09/
202 Updated Zybo design to reintroduce VDU8 driving the PmodVGA on pmod connectors JC+JD.
This version also uses PmodUSBUART on JE. To use PmodRS232 you must edit the .ucf file and select the appropriate pin LOCs.		 davidgb 1197d 07h /System09/
201 A copy of XSA-3S1000.ucf and System09_Xess_XSA-3S1000.vhd that have dual serial ports with no handshake. davidgb 1204d 01h /System09/
200 Started adding back in video support - VDU8 instantiated and RGBHV bits sent to Pmod JE port. davidgb 1210d 23h /System09/
199 Add in full RS-232 handshake for PmodUSBUART. davidgb 1212d 00h /System09/
198 Update UCF file to select Pmod pinout compatible with the PmodUSBUART.
To use, make sure PmodUSBUART has JP1 as "LCL". Connect the usb to the uart and open the terminal program. Test the transmission via the LED on the Pmod. Then (carefully) plug into Pmod port on Zybo.		 davidgb 1212d 02h /System09/
197 Updates from John Kent:
-- 4.5 John Kent 2012-02-04 Re-arranged Rx & Tx Baud clock edge detect.
-- 4.6 John Kent 3021-01-30 Double sample RxC, TxC, and RxD with cpu_clk
-- for 125MHz Clock on Zybo Z7 board.		 davidgb 1218d 23h /System09/
196 Working system boots to SBUG. Uses RS232 Pmod (no handshake) and 57600,8,N,1 (no handshake) hyperterm. davidgb 1218d 23h /System09/
195 Switched to using the UART over usb for the console port. davidgb 1219d 00h /System09/
194 Finally have a working board. davidgb 1219d 00h /System09/
193 Fixed part of the ACIA problem - the polarity of the NMI was wrong. Now get clean output but input to the ACIA is not working. Also fixed the 32k addressing davidgb 1219d 03h /System09/
192 Fixed part of the ACIA problem - the polarity of the NMI was wrong. Now get clean output but input to the ACIA is not working. davidgb 1219d 03h /System09/
191 check in file so that you do not need to generate it when running ISE in gui davidgb 1220d 00h /System09/
190 check in file so that you do not need to generate it when running ISE in gui davidgb 1220d 00h /System09/

1 2 Next >

Show All

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.