| Rev |
Log message |
Author |
Age |
Path |
| 49 |
Added some documentation to make the read and write calls easier to understand. |
dgisselq |
3000d 04h |
/xulalx25soc/trunk/sw/ |
| 46 |
This is a bug fix release--fixing the bug that kept dumpsdram.cpp/wbsdram.v
from working when long pipelined reads were interrupted by the necessity of
a pair of refresh cycles. |
dgisselq |
3002d 05h |
/xulalx25soc/trunk/sw/ |
| 42 |
Minor changes. |
dgisselq |
3006d 01h |
/xulalx25soc/trunk/sw/ |
| 41 |
Bug fix. This was preventing dumpsdram from accurately reading back what
had been written to the RAM earlier. |
dgisselq |
3006d 01h |
/xulalx25soc/trunk/sw/ |
| 40 |
This adds to dumpsdram the capability to run over a port, such as with
busmaster_tb. |
dgisselq |
3007d 12h |
/xulalx25soc/trunk/sw/ |
| 38 |
Updated to remove the build dependence upon ZipCPU. |
dgisselq |
3009d 11h |
/xulalx25soc/trunk/sw/ |
| 33 |
Oops -- the audio was wired audio first then the interrupt controller, not
the other way around. This adjusts regdefs to match what's on the chip. |
dgisselq |
3014d 04h |
/xulalx25soc/trunk/sw/ |
| 31 |
A bug fix, although one that rearranges the bus. The first four I/O locations
have been adjusted. The new locations are reflected in wishbone.html. In
addition, the PWM and UART devices no longer create bus errors when accessed.
Finally, this version uses a `define XULA25 to determine whether or not to build
for the XuLA2-LX9 or the XuLA2-LX25. If defined, it will build for the
XuLA2-LX25. If not, for the XuLA2-LX9. The ideal location for this define
would be to place it into your Xilinx configuration, should you wish to build
for the LX25. |
dgisselq |
3014d 04h |
/xulalx25soc/trunk/sw/ |
| 30 |
Bug fixes. In particular, this fixes a segmentation violation. |
dgisselq |
3014d 08h |
/xulalx25soc/trunk/sw/ |
| 29 |
This adds a vastly updated and superious ziprun capability to the repository.
ziprun now accepts ELF program files *only*, reads them, and places them onto
the board. This includes the ability, within the ELF file, of specifying
whether or not the data is sent to block ram, SD ram, or Flash, as well as
the ability of specifying the initial address. (Of course, that's a one time
thing--to always have the same initial address, set the address in
rtl/busmaster.v) |
dgisselq |
3015d 00h |
/xulalx25soc/trunk/sw/ |
| 28 |
Oops--two files needed by zipdbg weren't originally placed in the directory. |
dgisselq |
3015d 05h |
/xulalx25soc/trunk/sw/ |
| 25 |
Fixing compile time warnings. |
dgisselq |
3015d 05h |
/xulalx25soc/trunk/sw/ |
| 24 |
Added the #define necessary to enable (and clear) SCOPE interrupts. |
dgisselq |
3021d 03h |
/xulalx25soc/trunk/sw/ |
| 17 |
Some basic updates, to include adding in a missing file (zipstate). Most of
these updates include making sure that the XuLA2 device can be accessed via
the USB. (Prior versions accessed the FPGA via serial port or network ...) |
dgisselq |
3080d 05h |
/xulalx25soc/trunk/sw/ |
| 13 |
This version is now working. (It probably would've worked before, but
everything is now working.) |
dgisselq |
3082d 00h |
/xulalx25soc/trunk/sw/ |
| 11 |
Getting software up and running on the board for the first time. (Not there
yet, but I think these items have now proven themselves.) |
dgisselq |
3082d 03h |
/xulalx25soc/trunk/sw/ |
| 7 |
Mostly minor changes. Fixed the legal copyright statement in the UART files,
adjusted some comments, and made sure that the zipdbg program contained all
the latest features from our Vault. |
dgisselq |
3084d 13h |
/xulalx25soc/trunk/sw/ |
| 5 |
Initial software version, in support of the project. At this point, they are
provided with no guarantees that they work. (They did use to work--on an older
build, but I haven't been able to verify that they work with this newer build
yet.) |
dgisselq |
3084d 23h |
/xulalx25soc/trunk/sw/ |
