URL https://opencores.org/ocsvn/System09/System09/trunk

Subversion Repositories System09

[/] [System09/] [trunk/] [rtl/] [System09_Xess_XSA-3S1000/] [System09_Xess_XSA-3S1000.vhd] - Blame information for rev 223

Go to most recent revision | Details | Compare with Previous | View Log


--===========================================================================----
--
--  S Y N T H E Z I A B L E    System09 - SOC.
--
--  www.OpenCores.Org - February 2007
--  This core adheres to the GNU public license  
--
-- File name      : System09_Xess_XSA-3S1000.vhd
--
-- Purpose        : Top level file for 6809 compatible system on a chip
--                  Designed with Xilinx XC3S1000 Spartan 3 FPGA.
--                  Implemented With XESS XSA-3S1000 FPGA board.
--                  *** Note ***
--                  This configuration can run Flex9 however it only has
--                  32k bytes of user memory and the VDU is monochrome
--                  The design needs to be updated to use the SDRAM on 
--                  the XSA-3S1000 board.
--                  This configuration also lacks a DAT so cannot use
--                  the RAM Disk features of SYS09BUG.
--
-- Dependencies   : ieee.Std_Logic_1164
--                  ieee.std_logic_unsigned
--                  ieee.std_logic_arith
--                  ieee.numeric_std
--                  unisim.vcomponents
--
-- Uses           : mon_rom    (sys09bug_rom4k_b16.vhd) Sys09Bug Monitor ROM
--                  cpu09      (cpu09.vhd)          CPU core
--                  ACIA_6850  (acia6850.vhd)      ACIA / UART
--                  ACIA_Clock (ACIA_Clock.vhd)      ACIA clock.
--                  keyboard   (keyboard.vhd)        PS/2 Keyboard interface
--                             (ps2_keyboard.vhd)
--                             (keymap_rom_slice.vhd) Key map table 
--                  vdu8_mono  (vdu8_mono.vhd)        Monochrome VDU
--                             (char_rom2k_b16.vhd)
--                             (ram2k_b16.vhd)
--                  timer      (timer.vhd)            Interrupt timer
--                  trap       (trap.vhd)             Bus condition trap logic
--                  flex_ram   (flex9_ram8k_b16.vhd)  Flex operating system
--                  ram_32K    (ram32k_b16.vhd)       32 KBytes of Block RAM
--                  
-- 
-- Author         : John E. Kent      
--                  dilbert57@opencores.org      
--
-- Memory Map     :
--
-- $0000 - User program RAM (32K Bytes)
-- $C000 - Flex Operating System memory (8K Bytes)
-- $E000 - ACIA (SWTPc)
-- $E010 - Reserved for FD1771 FDC (SWTPc)
-- $E020 - Keyboard
-- $E030 - VDU
-- $E040 - IDE / Compact Flash interface
-- $E050 - Timer
-- $E060 - Bus trap
-- $E070 - Reserced for Parallel I/O (B5-X300)
-- $E080 - Reserved for 6821 PIA (?) (SWTPc)
-- $E090 - Reserved for 6840 PTM (?) (SWTPc)
-- $F000 - Sys09Bug monitor Program (4K Bytes)
--
--===========================================================================----
--
-- Revision History:
--===========================================================================--
-- Version 0.1 - 20 March 2003
-- Version 0.2 - 30 March 2003
-- Version 0.3 - 29 April 2003
-- Version 0.4 - 29 June 2003
--
-- Version 0.5 - 19 July 2003
-- prints out "Hello World"
--
-- Version 0.6 - 5 September 2003
-- Runs SBUG
--
-- Version 1.0- 6 Sep 2003 - John Kent
-- Inverted SysClk
-- Initial release to Open Cores
--
-- Version 1.1 - 17 Jan 2004 - John Kent
-- Updated miniUart.
--
-- Version 1.2 - 25 Jan 2004 - John Kent
-- removed signals "test_alu" and "test_cc" 
-- Trap hardware re-instated.
--
-- Version 1.3 - 11 Feb 2004 - John Kent
-- Designed forked off to produce System09_VDU
-- Added VDU component
-- VDU runs at 25MHz and divides the clock by 2 for the CPU
-- UART Runs at 57.6 Kbps
--
-- Version 2.0 - 2 September 2004 - John Kent
-- ported to Digilent Xilinx Spartan3 starter board
-- removed Compact Flash and Trap Logic.
-- Replaced SBUG with KBug9s
--
-- Version 3.0 - 29th August 2006 - John Kent
-- Adapted to XSA-3S1000 board.
-- Removed DAT and miniUART.
-- Used 32KBytes of Block RAM.
--
-- Version 3.1 - 15th January 2007 - John Kent
-- Modified vdu8 interface
-- Added a clock divider
--
-- Version 3.2 - 25th February 2007 - John Kent
-- reinstated ACIA_6850 and ACIA_Clock
-- Updated VDU8 & Keyboard with generic parameters
-- Defined Constants for clock speed calculations
--
-- Version 3.3 - 1st July 2007 - John Kent
-- Made VDU mono to save on one RAMB16
-- Used distributed memory for Key Map ROM to save one RAMB16
-- Added Flex RAM at $C000 to $DFFF using 4 spare RAMB16s
-- Added timer and trap logic
-- Added IDE Interface for Compact Flash
-- Replaced KBug9s and stack with Sys09Bug.
--
-- Version 4.0 - 1st February 2008 - John kent
-- Replaced Block RAM with SDRAM Interface
-- Modified Hold timing for SDRAM
-- Added CF and Ethernet interface 
-- via the 16 bit peripheral bus at $E100
--
--===========================================================================--
library ieee;
   use ieee.std_logic_1164.all;
   use IEEE.STD_LOGIC_ARITH.ALL;
   use IEEE.STD_LOGIC_UNSIGNED.ALL;
   use ieee.numeric_std.all;
library work;
   use work.common.all;
   use WORK.xsasdram.all;
library unisim;
   use unisim.vcomponents.all;
 
entity system09 is
  port(
    CLKA         : in  Std_Logic;  -- 100MHz Clock input
--    CLKB         : in  Std_Logic;  -- 50MHz Clock input
    SW2_N        : in  Std_logic;  -- Master Reset input (active low)
    SW3_N        : in  Std_logic;  -- Non Maskable Interrupt input (active low)
 
    -- PS/2 Keyboard
    ps2_clk      : inout Std_logic;
    ps2_dat      : inout Std_Logic;
 
    -- CRTC output signals
    vga_vsync_n  : out Std_Logic;
    vga_hsync_n  : out Std_Logic;
    vga_blue     : out std_logic_vector(2 downto 0);
    vga_green    : out std_logic_vector(2 downto 0);
    vga_red      : out std_logic_vector(2 downto 0);
 
    -- RS232 Port
    RS232_RXD    : in  Std_Logic;
    RS232_TXD    : out Std_Logic;
    RS232_CTS    : in  Std_Logic;
    RS232_RTS    : out Std_Logic;
 
    -- Status 7 segment LED
    S            : out std_logic_vector(7 downto 0);
 
    -- SDRAM side
    SDRAM_clkfb  : in  std_logic;            -- feedback SDRAM clock after PCB delays
    SDRAM_clkout : out std_logic;            -- clock to SDRAM
    SDRAM_CKE    : out std_logic;            -- clock-enable to SDRAM
    SDRAM_CS_N   : out std_logic;            -- chip-select to SDRAM
    SDRAM_RAS_N  : out std_logic;            -- SDRAM row address strobe
    SDRAM_CAS_N  : out std_logic;            -- SDRAM column address strobe
    SDRAM_WE_N   : out std_logic;            -- SDRAM write enable
    SDRAM_BA     : out std_logic_vector(1 downto 0);  -- SDRAM bank address
    SDRAM_A      : out std_logic_vector(12 downto 0);  -- SDRAM row/column address
    SDRAM_D      : inout  std_logic_vector(15 downto 0);  -- data from SDRAM
    SDRAM_DQMH   : out std_logic;            -- enable upper-byte of SDRAM databus if true
    SDRAM_DQML   : out std_logic;            -- enable lower-byte of SDRAM databus if true
 
    -- Peripheral I/O bus $E100 - $E1FF
    PB_RD_N      : out std_logic;
    PB_WR_N      : out std_logic;
    PB_A         : out std_logic_vector(4 downto 0);
    PB_D         : inout std_logic_vector(15 downto 0);
 
    -- IDE Compact Flash $E100 - $E13F
    ide_dmack_n  : out std_logic;
    ide_cs0_n    : out std_logic;
    ide_cs1_n    : out std_logic;
 
    -- Ethernet $E140 - $E17F
    ether_cs_n   : out std_logic;
    ether_aen    : out std_logic; -- Ethernet address enable not 
    ether_bhe_n  : out std_logic; -- Ethernet bus high enable 
    ether_clk    : in  std_logic; -- Ethernet clock 
    ether_rdy    : in  std_logic; -- Ethernet ready
    ether_irq    : in  std_logic; -- Ethernet irq - Shared with BAR6
 
    -- Slot 1 $E180 - $E1BF
    slot1_cs_n   : out std_logic;
--  slot1_irq    : in  std_logic;
 
    -- Slot 2 $E1C0 - $E1FF
    slot2_cs_n   : out std_logic;
--  slot2_irq    : in  std_logic;
 
-- CPU Debug Interface signals
--    cpu_reset_o     : out Std_Logic;
--    cpu_clk_o       : out Std_Logic;
--    cpu_rw_o        : out std_logic;
--    cpu_vma_o       : out std_logic;
--    cpu_halt_o      : out std_logic;
--    cpu_hold_o      : out std_logic;
--    cpu_firq_o      : out std_logic;
--    cpu_irq_o       : out std_logic;
--    cpu_nmi_o       : out std_logic;
--    cpu_addr_o      : out std_logic_vector(15 downto 0);
--    cpu_data_in_o   : out std_logic_vector(7 downto 0);
--    cpu_data_out_o  : out std_logic_vector(7 downto 0);
 
    -- Disable Flash
    FLASH_CE_N   : out std_logic
  );
end system09;
 
-------------------------------------------------------------------------------
-- Architecture for System09
-------------------------------------------------------------------------------
architecture rtl of system09 is
 
  -----------------------------------------------------------------------------
  -- constants
  -----------------------------------------------------------------------------
 
  -- SDRAM
  constant MEM_CLK_FREQ         : natural := 100_000; -- operating frequency of Memory in KHz
  constant SYS_CLK_DIV          : real    := 2.0;    -- divisor for FREQ (can only be 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0, 8.0 or 16.0)
  constant PIPE_EN              : boolean := false;  -- if true, enable pipelined read operations
  constant MAX_NOP              : natural := 10000;  -- number of NOPs before entering self-refresh
  constant MULTIPLE_ACTIVE_ROWS : boolean := false;  -- if true, allow an active row in each bank
  constant DATA_WIDTH           : natural := 16;     -- host & SDRAM data width
  constant NROWS                : natural := 8192;   -- number of rows in SDRAM array
  constant NCOLS                : natural := 512;    -- number of columns in SDRAM array
  constant HADDR_WIDTH          : natural := 24;     -- host-side address width
  constant SADDR_WIDTH          : natural := 13;     -- SDRAM-side address width
 
  constant SYS_CLK_FREQ         : natural := ((MEM_CLK_FREQ*2)/integer(SYS_CLK_DIV*2.0))*1000;  -- FPGA System Clock
  constant CPU_CLK_FREQ         : natural := 25_000_000;  -- CPU Clock (Hz)
  constant CPU_CLK_DIV          : natural := (SYS_CLK_FREQ/CPU_CLK_FREQ);
  constant VGA_CLK_FREQ         : natural := 25_000_000;  -- VGA Pixel Clock
  constant VGA_CLK_DIV          : natural := ((MEM_CLK_FREQ*1000)/VGA_CLK_FREQ);
  constant BAUD_RATE            : integer := 57600;     -- Baud Rate
  constant ACIA_CLK_FREQ        : integer := BAUD_RATE * 16;
 
  constant TRESET               : natural := 300;      -- min initialization interval (us)
  constant RST_CYCLES           : natural := 1+(TRESET*(MEM_CLK_FREQ/1_000));  -- SDRAM power-on initialization interval
 
  type hold_state_type is ( hold_release_state, hold_request_state );
 
  -----------------------------------------------------------------------------
  -- Signals
  -----------------------------------------------------------------------------
  -- BOOT ROM
  signal rom_cs         : Std_logic;
  signal rom_data_out   : Std_Logic_Vector(7 downto 0);
 
  -- Flex Memory & Monitor Stack
  signal flex_cs        : Std_logic;
  signal flex_data_out  : Std_Logic_Vector(7 downto 0);
 
  -- ACIA/UART Interface signals
  signal acia_data_out  : Std_Logic_Vector(7 downto 0);
  signal acia_cs        : Std_Logic;
  signal acia_irq       : Std_Logic;
  signal acia_clk       : Std_Logic;
  signal rxd            : Std_Logic;
  signal txd            : Std_Logic;
  signal DCD_n          : Std_Logic;
  signal RTS_n          : Std_Logic;
  signal CTS_n          : Std_Logic;
 
  -- keyboard port
  signal keyboard_data_out : std_logic_vector(7 downto 0);
  signal keyboard_cs       : std_logic;
  signal keyboard_irq      : std_logic;
 
  -- RAM
  signal ram_cs         : std_logic; -- memory chip select
  signal ram_data_out   : std_logic_vector(7 downto 0);
  signal ram_rd_req     : std_logic; -- ram read request (asynch set on ram read, cleared falling CPU clock edge)
  signal ram_wr_req     : std_logic; -- ram write request (set on rising CPU clock edge, asynch clear on acknowledge) 
  signal ram_hold       : std_logic; -- hold off slow accesses
  signal ram_release    : std_logic; -- Release ram hold
 
  -- CPU Interface signals
  signal cpu_reset      : Std_Logic;
  signal cpu_clk        : Std_Logic;
  signal cpu_rw         : std_logic;
  signal cpu_vma        : std_logic;
  signal cpu_halt       : std_logic;
  signal cpu_hold       : std_logic;
  signal cpu_firq       : std_logic;
  signal cpu_irq        : std_logic;
  signal cpu_nmi        : std_logic;
  signal cpu_addr       : std_logic_vector(15 downto 0);
  signal cpu_data_in    : std_logic_vector(7 downto 0);
  signal cpu_data_out   : std_logic_vector(7 downto 0);
 
  -- Dynamic Address Translation
  signal dat_cs       : std_logic;
  signal dat_addr     : std_logic_vector(7 downto 0);
 
  -- Video Display Unit
  signal vdu_cs         : std_logic;
  signal vdu_data_out   : std_logic_vector(7 downto 0);
  signal vga_red_o      : std_logic;
  signal vga_green_o    : std_logic;
  signal vga_blue_o     : std_logic;
 
  -- timer
  signal timer_data_out : std_logic_vector(7 downto 0);
  signal timer_cs       : std_logic;
  signal timer_irq      : std_logic;
 
  -- trap
  signal trap_cs        : std_logic;
  signal trap_data_out  : std_logic_vector(7 downto 0);
  signal trap_irq       : std_logic;
 
  -- Peripheral Bus port
  signal pb_data_out   : std_logic_vector(7 downto 0);
  signal pb_cs         : std_logic;   -- peripheral bus chip select
  signal pb_wru        : std_logic;   -- upper byte write strobe
  signal pb_wrl        : std_logic;   -- lower byte write strobe
  signal pb_rdu        : std_logic;   -- upper byte read strobe
  signal pb_rdl        : std_logic;   -- lower byte read strobe
  signal pb_hold       : std_logic;   -- hold peripheral bus access
  signal pb_release    : std_logic;   -- release hold of peripheral bus
  signal pb_count      : std_logic_vector(3 downto 0); -- hold counter
  signal pb_hold_state : hold_state_type;
  signal pb_wreg       : std_logic_vector(7 downto 0); -- lower byte write register
  signal pb_rreg       : std_logic_vector(7 downto 0); -- lower byte read register
 
  -- Peripheral chip selects on Peripheral Bus
  signal ide_cs        : std_logic; -- IDE CF interface
  signal ether_cs      : std_logic; -- Ethernet interface
  signal slot1_cs      : std_logic; -- Expansion slot 1
  signal slot2_cs      : std_logic; -- Expansion slot 2
 
  signal rst_i         : std_logic;     -- internal reset signal
  signal clk_i         : std_logic;     -- internal master clock signal
  signal lock          : std_logic;     -- SDRAM clock DLL lock indicator
 
  -- signals that go through the SDRAM host-side interface
  signal opBegun       : std_logic;        -- SDRAM operation started indicator
  signal earlyBegun    : std_logic;        -- SDRAM operation started indicator
  signal ramDone       : std_logic;        -- SDRAM operation complete indicator
  signal rdDone        : std_logic;        -- SDRAM read operation complete indicator
  signal wrDone        : std_logic;        -- SDRAM write operation complete indicator
  signal hAddr         : std_logic_vector(HADDR_WIDTH-1 downto 0);  -- host address bus
  signal hDIn          : std_logic_vector(DATA_WIDTH-1 downto 0);  -- host-side data to SDRAM
  signal hDOut         : std_logic_vector(DATA_WIDTH-1 downto 0);  -- host-side data from SDRAM
  signal hRd           : std_logic;        -- host-side read control signal
  signal hWr           : std_logic;        -- host-side write control signal
  signal hUds          : std_logic;        -- host-side upper data strobe
  signal hLds          : std_logic;        -- host-side lower data strobe
  signal rdPending     : std_logic;        -- read operation pending in SDRAM pipeline
  type ram_type is (ram_state_0,
                    ram_state_rd1, ram_state_rd2,
                    ram_state_wr1,
                    ram_state_3 );
  signal ram_state     : ram_type;
 
  signal CountL        : std_logic_vector(23 downto 0);
  signal clk_count     : natural range 0 to CPU_CLK_DIV;
  signal Clk25         : std_logic;
  signal vga_clk       : std_logic;
 
-----------------------------------------------------------------
--
-- CPU09 CPU core
--
-----------------------------------------------------------------
 
component cpu09
  port (
    clk:      in  std_logic;
    rst:      in  std_logic;
    vma:      out std_logic;
    addr:     out std_logic_vector(15 downto 0);
    rw:       out std_logic;     -- Asynchronous memory interface
    data_out: out std_logic_vector(7 downto 0);
    data_in:  in  std_logic_vector(7 downto 0);
    irq:      in  std_logic;
    firq:     in  std_logic;
    nmi:      in  std_logic;
    halt:     in  std_logic;
    hold:     in  std_logic
  );
end component;
 
----------------------------------------
--
-- 4K Block RAM Monitor ROM
-- $F000 - $FFFF
--
----------------------------------------
 
component mon_rom
  Port (
    clk   : in  std_logic;
    rst   : in  std_logic;
    cs    : in  std_logic;
    rw    : in  std_logic;
    addr  : in  std_logic_vector (11 downto 0);
    data_out : out std_logic_vector (7 downto 0);
    data_in : in  std_logic_vector (7 downto 0)
  );
end component;
 
----------------------------------------
--
-- 8KBytes Block RAM for FLEX9
-- $C000 - $DFFF
--
----------------------------------------
 
component flex_ram
  Port (
    clk      : in  std_logic;
    rst      : in  std_logic;
    cs       : in  std_logic;
    rw       : in  std_logic;
    addr     : in  std_logic_vector (12 downto 0);
    data_out    : out std_logic_vector (7 downto 0);
    data_in    : in  std_logic_vector (7 downto 0)
  );
end component;
 
-----------------------------------------------------------------
--
-- 6850 Compatible ACIA / UART
--
-----------------------------------------------------------------
 
component acia6850
  port (
    clk      : in  Std_Logic;  -- System Clock
    rst      : in  Std_Logic;  -- Reset input (active high)
    cs       : in  Std_Logic;  -- miniUART Chip Select
    rw       : in  Std_Logic;  -- Read / Not Write
    addr     : in  Std_Logic;  -- Register Select
    data_in  : in  Std_Logic_Vector(7 downto 0); -- Data Bus In 
    data_out : out Std_Logic_Vector(7 downto 0); -- Data Bus Out
    irq      : out Std_Logic;  -- Interrupt
    RxC      : in  Std_Logic;  -- Receive Baud Clock
    TxC      : in  Std_Logic;  -- Transmit Baud Clock
    RxD      : in  Std_Logic;  -- Receive Data
    TxD      : out Std_Logic;  -- Transmit Data
    DCD_n    : in  Std_Logic;  -- Data Carrier Detect
    CTS_n    : in  Std_Logic;  -- Clear To Send
    RTS_n    : out Std_Logic   -- Request To send
  );
end component;
 
-----------------------------------------------------------------
--
-- ACIA Clock divider
--
-----------------------------------------------------------------
 
component ACIA_Clock
  generic (
    SYS_CLK_FREQ  : integer :=  SYS_CLK_FREQ;
    ACIA_CLK_FREQ : integer := ACIA_CLK_FREQ
  );
  port (
    clk      : in  Std_Logic;  -- System Clock Input
    ACIA_clk : out Std_logic   -- ACIA Clock output
  );
end component;
 
----------------------------------------
--
-- PS/2 Keyboard
--
----------------------------------------
 
component keyboard
  generic(
    KBD_CLK_FREQ : integer := CPU_CLK_FREQ
  );
  port(
    clk             : in    std_logic;
    rst             : in    std_logic;
    cs              : in    std_logic;
    rw              : in    std_logic;
    addr            : in    std_logic;
    data_in         : in    std_logic_vector(7 downto 0);
    data_out        : out   std_logic_vector(7 downto 0);
    irq             : out   std_logic;
    kbd_clk         : inout std_logic;
    kbd_data        : inout std_logic
  );
end component;
 
----------------------------------------
--
-- Video Display Unit.
--
----------------------------------------
 
component vdu8
  generic(
    VDU_CLK_FREQ           : integer := CPU_CLK_FREQ; -- HZ
    VGA_CLK_FREQ           : integer := VGA_CLK_FREQ; -- HZ
    VGA_HOR_CHARS          : integer := 80; -- CHARACTERS
    VGA_VER_CHARS          : integer := 25; -- CHARACTERS
    VGA_PIX_PER_CHAR       : integer := 8;  -- PIXELS
    VGA_LIN_PER_CHAR       : integer := 16; -- LINES
    VGA_HOR_BACK_PORCH     : integer := 40; -- PIXELS
    VGA_HOR_SYNC           : integer := 96; -- PIXELS
    VGA_HOR_FRONT_PORCH    : integer := 24; -- PIXELS
    VGA_VER_BACK_PORCH     : integer := 13; -- LINES
    VGA_VER_SYNC           : integer := 2;  -- LINES
    VGA_VER_FRONT_PORCH    : integer := 35  -- LINES
  );
  port(
    -- control register interface
    vdu_clk      : in  std_logic;  -- CPU Clock - 25MHz
    vdu_rst      : in  std_logic;
    vdu_cs       : in  std_logic;
    vdu_rw       : in  std_logic;
    vdu_addr     : in  std_logic_vector(2 downto 0);
    vdu_data_in  : in  std_logic_vector(7 downto 0);
    vdu_data_out : out std_logic_vector(7 downto 0);
 
    -- vga port connections
    vga_clk      : in  std_logic; -- VGA Pixel Clock - 25 MHz
    vga_red_o    : out std_logic;
    vga_green_o  : out std_logic;
    vga_blue_o   : out std_logic;
    vga_hsync_o  : out std_logic;
    vga_vsync_o  : out std_logic
  );
end component;
 
----------------------------------------
--
-- Timer module
--
----------------------------------------
 
component timer
  port (
    clk       : in std_logic;
    rst       : in std_logic;
    cs        : in std_logic;
    rw        : in std_logic;
    addr      : in std_logic;
    data_in   : in std_logic_vector(7 downto 0);
    data_out  : out std_logic_vector(7 downto 0);
    irq       : out std_logic
  );
end component;
 
------------------------------------------------------------
--
-- Bus Trap logic
--
------------------------------------------------------------
 
component trap
  port (
    clk        : in  std_logic;
    rst        : in  std_logic;
    cs         : in  std_logic;
    rw         : in  std_logic;
    vma        : in  std_logic;
    addr       : in  std_logic_vector(15 downto 0);
    data_in    : in  std_logic_vector(7 downto 0);
    data_out   : out std_logic_vector(7 downto 0);
    irq        : out std_logic
  );
end component;
 
----------------------------------------
--
-- Dynamic Address Translation Registers
--
----------------------------------------
 
component dat_ram
  port (
    clk      : in  std_logic;
    rst      : in  std_logic;
    cs       : in  std_logic;
    rw       : in  std_logic;
    addr_lo  : in  std_logic_vector(3 downto 0);
    addr_hi  : in  std_logic_vector(3 downto 0);
    data_in  : in  std_logic_vector(7 downto 0);
    data_out : out std_logic_vector(7 downto 0)
  );
end component;
 
----------------------------------------
--
-- SDRAM Controller for XSA-3S1000
--
----------------------------------------
 
component XSASDRAMCntl
  generic(
    FREQ                 :     natural := MEM_CLK_FREQ;-- operating frequency in KHz
    CLK_DIV              :     real    := SYS_CLK_DIV; -- divisor for FREQ (can only be 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0, 8.0 or 16.0)
    PIPE_EN              :     boolean := PIPE_EN;     -- if true, enable pipelined read operations
    MAX_NOP              :     natural := MAX_NOP;     -- number of NOPs before entering self-refresh
    MULTIPLE_ACTIVE_ROWS :     boolean := MULTIPLE_ACTIVE_ROWS;  -- if true, allow an active row in each bank
    DATA_WIDTH           :     natural := DATA_WIDTH;  -- host & SDRAM data width
    NROWS                :     natural := NROWS;       -- number of rows in SDRAM array
    NCOLS                :     natural := NCOLS;       -- number of columns in SDRAM array
    HADDR_WIDTH          :     natural := HADDR_WIDTH; -- host-side address width
    SADDR_WIDTH          :     natural := SADDR_WIDTH  -- SDRAM-side address width
  );
  port(
    -- host side
    clk                  : in  std_logic;  -- master clock
    bufclk               : out std_logic;  -- buffered master clock
    clk1x                : out std_logic;  -- host clock sync'ed to master clock (and divided if CLK_DIV>1)
    clk2x                : out std_logic;  -- double-speed host clock
    lock                 : out std_logic;  -- true when host clock is locked to master clock
    rst                  : in  std_logic;  -- reset
    rd                   : in  std_logic;  -- initiate read operation
    wr                   : in  std_logic;  -- initiate write operation
    uds                  : in  std_logic;  -- upper data strobe
    lds                  : in  std_logic;  -- lower data strobe
    earlyOpBegun         : out std_logic;  -- read/write/self-refresh op begun     (async)
    opBegun              : out std_logic;  -- read/write/self-refresh op begun (clocked)
    rdPending            : out std_logic;  -- read operation(s) are still in the pipeline
    done                 : out std_logic;  -- read or write operation is done
    rdDone               : out std_logic;  -- read done and data is available
    hAddr                : in  std_logic_vector(HADDR_WIDTH-1 downto 0);  -- address from host
    hDIn                 : in  std_logic_vector(DATA_WIDTH-1 downto 0);  -- data from host
    hDOut                : out std_logic_vector(DATA_WIDTH-1 downto 0);  -- data to host
    status               : out std_logic_vector(3 downto 0);  -- diagnostic status of the FSM         
 
    -- SDRAM side
    sclkfb               : in    std_logic;           -- clock from SDRAM after PCB delays
    sclk                 : out   std_logic;           -- SDRAM clock sync'ed to master clock
    cke                  : out   std_logic;           -- clock-enable to SDRAM
    cs_n                 : out   std_logic;           -- chip-select to SDRAM
    ras_n                : out   std_logic;           -- SDRAM row address strobe
    cas_n                : out   std_logic;           -- SDRAM column address strobe
    we_n                 : out   std_logic;           -- SDRAM write enable
    ba                   : out   std_logic_vector(1 downto 0);  -- SDRAM bank address bits
    sAddr                : out   std_logic_vector(SADDR_WIDTH-1 downto 0);  -- SDRAM row/column address
    sData                : inout std_logic_vector(DATA_WIDTH-1 downto 0);  -- SDRAM in/out databus
    dqmh                 : out   std_logic;           -- high databits I/O mask
    dqml                 : out   std_logic            -- low databits I/O mask
  );
end component;
 
--
-- Clock buffer
--
 
component BUFG
   Port (
     i: in std_logic;
     o: out std_logic
  );
end component;
 
begin
 
  -----------------------------------------------------------------------------
  -- Instantiation of internal components
  -----------------------------------------------------------------------------
 
  my_cpu : cpu09
    port map (
      clk       => cpu_clk,
      rst       => cpu_reset,
      vma       => cpu_vma,
      addr      => cpu_addr(15 downto 0),
      rw        => cpu_rw,
      data_out  => cpu_data_out,
      data_in   => cpu_data_in,
      irq       => cpu_irq,
      firq      => cpu_firq,
      nmi       => cpu_nmi,
      halt      => cpu_halt,
      hold      => cpu_hold
    );
 
  my_rom : mon_rom
    port map (
      clk   => cpu_clk,
      rst   => cpu_reset,
      cs    => rom_cs,
      rw    => '1',
      addr  => cpu_addr(11 downto 0),
      data_in => cpu_data_out,
      data_out => rom_data_out
    );
 
  my_flex : flex_ram
    port map (
      clk       => cpu_clk,
      rst       => cpu_reset,
      cs        => flex_cs,
      rw        => cpu_rw,
      addr      => cpu_addr(12 downto 0),
      data_out     => flex_data_out,
      data_in     => cpu_data_out
    );
 
  my_acia  : acia6850
    port map (
      clk       => cpu_clk,
      rst       => cpu_reset,
      cs        => acia_cs,
      rw        => cpu_rw,
      addr      => cpu_addr(0),
      data_in   => cpu_data_out,
      data_out  => acia_data_out,
      irq       => acia_irq,
      RxC       => acia_clk,
      TxC       => acia_clk,
      RxD       => rxd,
      TxD       => txd,
      DCD_n     => dcd_n,
      CTS_n     => cts_n,
      RTS_n     => rts_n
    );
 
  my_ACIA_Clock : ACIA_Clock
    generic map(
      SYS_CLK_FREQ  =>  SYS_CLK_FREQ,
      ACIA_CLK_FREQ => ACIA_CLK_FREQ
    )
    port map(
      clk        => Clk_i,
      acia_clk   => acia_clk
    );
 
  ----------------------------------------
  --
  -- PS/2 Keyboard Interface
  --
  ----------------------------------------
  my_keyboard : keyboard
    generic map (
      KBD_CLK_FREQ => CPU_CLK_FREQ
    )
    port map(
      clk          => cpu_clk,
      rst          => cpu_reset,
      cs           => keyboard_cs,
      rw           => cpu_rw,
      addr         => cpu_addr(0),
      data_in      => cpu_data_out(7 downto 0),
      data_out     => keyboard_data_out(7 downto 0),
      irq          => keyboard_irq,
      kbd_clk      => ps2_clk,
      kbd_data     => ps2_dat
    );
 
  ----------------------------------------
  --
  -- Video Display Unit instantiation
  --
  ----------------------------------------
  my_vdu : vdu8
    generic map(
      VDU_CLK_FREQ           => CPU_CLK_FREQ, -- HZ
      VGA_CLK_FREQ           => VGA_CLK_FREQ, -- HZ
      VGA_HOR_CHARS          => 80, -- CHARACTERS
      VGA_VER_CHARS          => 25, -- CHARACTERS
      VGA_PIX_PER_CHAR       => 8,  -- PIXELS
      VGA_LIN_PER_CHAR       => 16, -- LINES
      VGA_HOR_BACK_PORCH     => 40, -- PIXELS
      VGA_HOR_SYNC           => 96, -- PIXELS
      VGA_HOR_FRONT_PORCH    => 24, -- PIXELS
      VGA_VER_BACK_PORCH     => 13, -- LINES
      VGA_VER_SYNC           => 2,  -- LINES
      VGA_VER_FRONT_PORCH    => 35  -- LINES
    )
    port map(
      -- Control Registers
      vdu_clk       => cpu_clk,               -- 12.5 MHz System Clock in
      vdu_rst       => cpu_reset,
      vdu_cs        => vdu_cs,
      vdu_rw        => cpu_rw,
      vdu_addr      => cpu_addr(2 downto 0),
      vdu_data_in   => cpu_data_out,
      vdu_data_out  => vdu_data_out,
      -- vga port connections
      vga_clk       => vga_clk,               -- 25 MHz VDU pixel clock
      vga_red_o     => vga_red_o,
      vga_green_o   => vga_green_o,
      vga_blue_o    => vga_blue_o,
      vga_hsync_o   => vga_hsync_n,
      vga_vsync_o   => vga_vsync_n
   );
 
  ----------------------------------------
  --
  -- Timer Module
  --
  ----------------------------------------
  my_timer  : timer
    port map (
      clk       => cpu_clk,
      rst       => cpu_reset,
      cs        => timer_cs,
      rw        => cpu_rw,
      addr      => cpu_addr(0),
      data_in   => cpu_data_out,
      data_out  => timer_data_out,
      irq       => timer_irq
    );
 
  ----------------------------------------
  --
  -- Bus Trap Interrupt logic
  --
  ----------------------------------------
  my_trap : trap
    port map (
      clk        => cpu_clk,
      rst        => cpu_reset,
      cs         => trap_cs,
      rw         => cpu_rw,
      vma        => cpu_vma,
      addr       => cpu_addr,
      data_in    => cpu_data_out,
      data_out   => trap_data_out,
      irq        => trap_irq
    );
 
  my_dat : dat_ram
    port map (
      clk       => cpu_clk,
      rst       => cpu_reset,
      cs        => dat_cs,
      rw        => cpu_rw,
      addr_hi   => cpu_addr(15 downto 12),
      addr_lo   => cpu_addr(3 downto 0),
      data_in   => cpu_data_out,
      data_out  => dat_addr(7 downto 0)
    );
 
  ------------------------------------------------------------------------
  -- Instantiate the SDRAM controller that connects to the memory tester
  -- module and interfaces to the external SDRAM chip.
  ------------------------------------------------------------------------
  u1 : xsaSDRAMCntl
    generic map(
      FREQ                 => MEM_CLK_FREQ,
      CLK_DIV              => SYS_CLK_DIV,
      PIPE_EN              => PIPE_EN,
      MAX_NOP              => MAX_NOP,
      MULTIPLE_ACTIVE_ROWS => MULTIPLE_ACTIVE_ROWS,
      DATA_WIDTH           => DATA_WIDTH,
      NROWS                => NROWS,
      NCOLS                => NCOLS,
      HADDR_WIDTH          => HADDR_WIDTH,
      SADDR_WIDTH          => SADDR_WIDTH
    )
    port map(
      -- Host Side
      clk                  => CLKA,     -- master clock from external clock source (unbuffered)
      bufclk               => open,     -- buffered master clock output
      clk1x                => clk_i,    -- synchronized master clock (accounts for delays to external SDRAM)
      clk2x                => open,     -- synchronized doubled master clock
      lock                 => lock,     -- DLL lock indicator
      rst                  => rst_i,    -- reset
      rd                   => hRd,      -- host-side SDRAM read control from memory tester
      wr                   => hWr,      -- host-side SDRAM write control from memory tester
      uds                  => hUds,     -- host-side SDRAM upper data strobe
      lds                  => hLds,     -- host-side SDRAM lower data strobe
      rdPending            => rdPending,-- read operation to SDRAM is in progress
      opBegun              => opBegun,  -- indicates memory read/write has begun
      earlyOpBegun         => earlyBegun,  -- early indicator that memory operation has begun
      rdDone               => rdDone,   -- indicates SDRAM memory read operation is done
      done                 => ramDone, -- indicates SDRAM memory read or write operation is done
      hAddr                => hAddr,    -- host-side address from memory tester to SDRAM
      hDIn                 => hDIn,     -- test data pattern from memory tester to SDRAM
      hDOut                => hDOut,    -- SDRAM data output to memory tester
      status               => open,     -- SDRAM controller state (for diagnostics)
      -- SDRAM Side
      sclkfb               => SDRAM_clkfb,    -- clock feedback with added external PCB delays
      sclk                 => SDRAM_clkout,   -- synchronized clock to external SDRAM
      cke                  => SDRAM_cke,      -- SDRAM clock enable
      cs_n                 => SDRAM_cs_n,     -- SDRAM chip-select
      ras_n                => SDRAM_ras_n,    -- SDRAM RAS
      cas_n                => SDRAM_cas_n,    -- SDRAM CAS
      we_n                 => SDRAM_we_n,     -- SDRAM write-enable
      ba                   => SDRAM_ba,       -- SDRAM bank address
      sAddr                => SDRAM_A,        -- SDRAM address
      sData                => SDRAM_D,        -- SDRAM databus
      dqmh                 => SDRAM_dqmh,     -- SDRAM DQMH
      dqml                 => SDRAM_dqml      -- SDRAM DQML
    );
 
  cpu_clk_buffer : BUFG
    port map(
      i => Clk25,
      o => cpu_clk
    );
 
  vga_clk_buffer : BUFG
    port map(
      i => Clk25,
      o => vga_clk
    );
 
  ----------------------------------------------------------------------
  --
  -- Process to decode memory map
  --
  ----------------------------------------------------------------------
 
  mem_decode: process( cpu_addr, cpu_rw, cpu_vma,
                     dat_addr,
                     rom_data_out,
                     flex_data_out,
                     acia_data_out,
                     keyboard_data_out,
                     vdu_data_out,
                     pb_data_out,
                     timer_data_out,
                     trap_data_out,
                     ram_data_out
                     )
  begin
    cpu_data_in <= (others=>'0');
    dat_cs      <= '0';
    rom_cs      <= '0';
    flex_cs     <= '0';
    acia_cs     <= '0';
    keyboard_cs <= '0';
    vdu_cs      <= '0';
    timer_cs    <= '0';
    trap_cs     <= '0';
    pb_cs       <= '0';
    ide_cs      <= '0';
    ether_cs    <= '0';
    slot1_cs    <= '0';
    slot2_cs    <= '0';
    ram_cs      <= '0';
 
    if cpu_addr( 15 downto 8 ) = "11111111" then  -- $FFxx
      cpu_data_in <= rom_data_out;
      dat_cs      <= cpu_vma;              -- write DAT
      rom_cs      <= cpu_vma;              -- read  ROM
 
    --
    -- Sys09Bug Monitor ROM $F000 - $FFFF
    --
    elsif dat_addr(3 downto 0) = "1111" then -- $XF000 - $XFFFF
      cpu_data_in <= rom_data_out;
      rom_cs      <= cpu_vma;
 
    --
    -- IO Devices $E000 - $E7FF
    --
    elsif dat_addr(3 downto 0) = "1110" then -- $XE000 - $XEFFF
      case cpu_addr(11 downto 8) is
        --
        -- SWTPC peripherals from $E000 to $E0FF
        --
        when "0000" =>
          case cpu_addr(7 downto 4) is
          --
          -- Console Port ACIA $E000 - $E00F
          --
            when "0000" => -- $E000
              cpu_data_in <= acia_data_out;
              acia_cs     <= cpu_vma;
 
            --
            -- Reserved
            -- Floppy Disk Controller port $E010 - $E01F
            --
 
            --
            -- Keyboard port $E020 - $E02F
            --
            when "0010" => -- $E020
              cpu_data_in <= keyboard_data_out;
              keyboard_cs <= cpu_vma;
 
            --
            -- VDU port $E030 - $E03F
            --
            when "0011" => -- $E030
              cpu_data_in <= vdu_data_out;
              vdu_cs      <= cpu_vma;
 
            --
            -- Reserved SWTPc MP-T Timer $E040 - $E04F
            --
            when "0100" => -- $E040
              cpu_data_in <= (others=> '0');
 
            --
            -- Timer $E050 - $E05F
            --
            when "0101" => -- $E050
              cpu_data_in <= timer_data_out;
              timer_cs    <= cpu_vma;
 
            --
            -- Bus Trap Logic $E060 - $E06F
            --
            when "0110" => -- $E060
              cpu_data_in <= trap_data_out;
              trap_cs     <= cpu_vma;
 
            --
            -- Reserved SWTPc MP-ID PIA Timer/Printer Port $E080 - $E08F
            --
 
            --
            -- Reserved SWTPc MP-ID PTM 6840 Timer Port $E090 - $E09F
            --
 
            --
            -- Remaining 6 slots reserved for non SWTPc Peripherals
            --
            when others => -- $E0A0 to $E0FF
              null;
          end case;
 
        --
        -- XST-3.0 Peripheral Bus goes here
        -- $E100 to $E1FF
        -- Four devices
        -- IDE, Ethernet, Slot1, Slot2
        --
        when "0001" =>
          cpu_data_in <= pb_data_out;
          pb_cs       <= cpu_vma;
          case cpu_addr(7 downto 6) is
            --
            -- IDE Interface $E100 to $E13F
            --
            when "00" =>
              ide_cs   <= cpu_vma;
            --
            -- Ethernet Interface $E140 to $E17F
            --
            when "01" =>
              ether_cs <= cpu_vma;
            --
            -- Slot 1 Interface $E180 to $E1BF
            --
            when "10" =>
              slot1_cs <= cpu_vma;
            --
            -- Slot 2 Interface $E1C0 to $E1FF
            --
            when "11" =>
              slot2_cs <= cpu_vma;
            --
            -- Nothing else
            --
            when others =>
              null;
          end case;
 
        --
        -- $E200 to $EFFF reserved for future use
        --
        when others =>
           null;
      end case;
 
    --
    -- Flex RAM $0C000 - $0DFFF
    --
    elsif dat_addr(7 downto 1) = "0000110" then -- $0C000 - $0DFFF
      cpu_data_in <= flex_data_out;
      flex_cs     <= cpu_vma;
 
    --
    -- Everything else is RAM
    --
    else
      cpu_data_in <= ram_data_out;
      ram_cs      <= cpu_vma;
    end if;
 
  end process;
 
  --
  -- 16-bit Peripheral Bus
  -- 6809 Big endian
  -- ISA bus little endian
  -- Not sure about IDE interface
  --
  peripheral_bus: process( clk_i, cpu_reset, cpu_rw, cpu_addr, cpu_data_out,
                         pb_cs, pb_wreg, pb_rreg )
  begin
    pb_wru <= pb_cs and (not cpu_rw) and (not cpu_addr(0));
    pb_wrl <= pb_cs and (not cpu_rw) and      cpu_addr(0) ;
    pb_rdu <= pb_cs and      cpu_rw  and (not cpu_addr(0));
    pb_rdl <= pb_cs and      cpu_rw  and      cpu_addr(0) ;
    pb_a   <= cpu_addr(5 downto 1);
 
    --
    -- Register upper byte from CPU on first CPU write
    -- and lower byte from the peripheral bus on first CPU read
    --
    if cpu_reset = '1' then
      pb_wreg <= (others => '0');
      pb_rreg <= (others => '0');
    elsif clk_i'event and clk_i ='1' then
      if pb_wru = '1' then
        pb_wreg <= cpu_data_out;
      end if;
      if pb_rdu = '1' then
        pb_rreg <= pb_d(7 downto 0);
      end if;
    end if;
    --
    -- Peripheral bus read and write strobes are
    -- Syncronized with the 50 MHz clock
    -- and are asserted until the peripheral bus hold is released
    --
    if cpu_reset = '1' then
      pb_wr_n <= '1';
      pb_rd_n <= '1';
    elsif clk_i'event and clk_i ='1' then
      if pb_hold = '1' then
        pb_wr_n  <= not pb_wrl;
        pb_rd_n  <= not pb_rdu;
      else
        pb_wr_n <= '1';
        pb_rd_n <= '1';
      end if;
    end if;
    --
    -- The peripheral bus will be an output 
    -- the registered even byte on data(15 downto 8)
    -- and the CPU odd bytes on data(7 downto 0)
    -- on odd byte writes
    --
    if pb_wrl = '1' then
      pb_d <= pb_wreg & cpu_data_out;
    else
      pb_d <= (others => 'Z');
    end if;
 
    --
    -- On even byte reads,
    -- the CPU reads the low (even) byte of the peripheral bus
    -- On odd byte reads,
    -- the CPU reads the registered (odd byte) input from the peripheral bus
    --
    if pb_rdu = '1' then
      pb_data_out <= pb_d(15 downto 8);
    elsif pb_rdl = '1' then
      pb_data_out <= pb_rreg;
    else
      pb_data_out <= (others => '0');
    end if;
 
  end process;
 
  --
  -- Hold Peripheral bus accesses for a few cycles
  --
  peripheral_bus_hold: process( cpu_clk, cpu_reset, pb_rdu, pb_wrl ) --, ether_rdy )
  begin
    if cpu_reset = '1' then
      pb_release    <= '0';
      pb_count      <= "0000";
      pb_hold_state <= hold_release_state;
    elsif rising_edge(cpu_clk) then
      --
      -- The perpheral bus hold signal should be generated on 
      -- 16 bit bus read which will be on even byte reads or 
      -- 16 bit bus write which will be on odd byte writes.
      -- 
      case pb_hold_state is
        when hold_release_state =>
          pb_release <= '0';
          if (pb_rdu = '1') or (pb_wrl = '1') then
            pb_count      <= "0100";
            pb_hold_state <= hold_request_state;
          elsif (pb_rdl = '1') or (pb_wru = '1') then
            pb_release    <= '1';
            pb_hold_state <= hold_release_state;
          end if;
 
        when hold_request_state =>
          if pb_count = "0000" then
--          if ether_rdy = '1' then
              pb_release    <= '1';
              pb_hold_state <= hold_release_state;
--          end if;
          else
            pb_count <= pb_count - "0001";
          end if;
        when others =>
          null;
      end case;
    end if;
  end process;
 
  --
  -- Compact Flash Control
  --
  compact_flash: process( ide_cs, cpu_addr )
  begin
   ide_cs0_n  <= not( ide_cs ) or cpu_addr(4);
   ide_cs1_n  <= not( ide_cs and cpu_addr(4));
   ide_dmack_n  <= '1';
  end process;
 
  --
  -- Interrupts and other bus control signals
  --
  interrupts : process( SW3_N,
                      pb_cs, pb_hold, pb_release, ram_hold,
--                    ether_irq, 
                      acia_irq,
                      keyboard_irq,
                      trap_irq,
                      timer_irq
                      )
  begin
    pb_hold    <= pb_cs and (not pb_release);
    cpu_irq    <= acia_irq or keyboard_irq;
    cpu_nmi    <= trap_irq or not( SW3_N );
    cpu_firq   <= timer_irq;
    cpu_halt   <= '0';
    cpu_hold   <= pb_hold or ram_hold;
    FLASH_CE_N <= '1';
  end process;
 
  --
  -- Flash 7 segment LEDS
  --
  my_led_flasher: process( clk_i, rst_i, CountL )
  begin
    if rst_i = '1' then
         CountL <= "000000000000000000000000";
    elsif rising_edge(clk_i) then
         CountL <= CountL + 1;
    end if;
    --  S(7 downto 0) <= CountL(23 downto 16);
  end process;
 
  --
  -- Generate CPU & Pixel Clock from Memory Clock
  --
  my_prescaler : process( clk_i, clk_count )
  begin
    if rising_edge( clk_i ) then
      if clk_count = 0 then
        clk_count <= CPU_CLK_DIV-1;
      else
        clk_count <= clk_count - 1;
      end if;
      if clk_count = 0 then
         clk25 <= '0';
      elsif clk_count = (CPU_CLK_DIV/2) then
         clk25 <= '1';
      end if;
    end if;
  end process;
 
  --
  -- Reset button and reset timer
  --
  my_switch_assignments : process( rst_i, SW2_N, lock )
  begin
    rst_i <= not SW2_N;
    cpu_reset <= rst_i or (not lock);
  end process;
 
  --
  -- RS232 signals:
  --
  my_acia_assignments : process( RS232_RXD, RS232_CTS, txd, rts_n )
  begin
    rxd       <= RS232_RXD;
    cts_n     <= RS232_CTS;
    dcd_n     <= '0';
    RS232_TXD <= txd;
    RS232_RTS <= rts_n;
  end process;
 
  --
  -- Pin assignments for ethernet controller
  --
  my_ethernet_assignments : process( clk_i, cpu_reset, ether_cs )
  begin
    ether_cs_n  <= not ether_cs;
    ether_aen   <= not ether_cs; -- Ethernet address enable not 
    ether_bhe_n <= '1';          -- Ethernet bus high enable - 8 bit access only
  end process;
 
  --
  -- I/O expansion slot assignments
  --
  my_slot_assignments : process( slot1_cs, slot2_cs)
  begin
    slot1_cs_n <= not slot1_cs;
    slot2_cs_n <= not slot2_cs;
  end process;
 
  --
  -- VGA ouputs
  --
  my_vga_assignments : process( vga_red_o, vga_green_o, vga_blue_o )
  begin
    VGA_red(0)   <= vga_red_o;
    VGA_red(1)   <= vga_red_o;
    VGA_red(2)   <= vga_red_o;
    VGA_green(0) <= vga_green_o;
    VGA_green(1) <= vga_green_o;
    VGA_green(2) <= vga_green_o;
    VGA_blue(0)  <= vga_blue_o;
    VGA_blue(1)  <= vga_blue_o;
    VGA_blue(2)  <= vga_blue_o;
  end process;
 
  --
  -- SDRAM read write control
  --
  my_sdram_rw : process( clk_i, cpu_reset,
                       opBegun, ramDone,
                       ram_state,
                       ram_rd_req, ram_wr_req )
  begin
    if( cpu_reset = '1' ) then
      hRd        <= '0';
      hWr        <= '0';
      ram_hold   <= '0';
      ram_state  <= ram_state_0;
 
    elsif( falling_edge(clk_i) ) then
      --
      -- ram state machine
      --
      case ram_state is
 
      when ram_state_0 =>
        if ram_rd_req = '1' then
          ram_hold   <= '1';
          hRd        <= '1';
          ram_state  <= ram_state_rd1;
        elsif ram_wr_req = '1' then
          ram_hold   <= '1';
          hWr        <= '1';
          ram_state  <= ram_state_wr1;
        end if;
 
      when ram_state_rd1 =>
        if opBegun = '1' then
          hRd        <= '0';
          ram_state  <= ram_state_rd2;
        end if;
 
      when ram_state_rd2 =>
        if ramDone = '1' then
          ram_hold   <= '0';
          ram_state  <= ram_state_3;
        end if;
 
      when ram_state_wr1 =>
        if opBegun = '1' then
          ram_hold   <= '0';
          hWr        <= '0';
          ram_state  <= ram_state_3;
        end if;
 
      when ram_state_3 =>
        if ram_release = '1' then
          ram_state  <= ram_state_0;
        end if;
 
      when others =>
        hRd        <= '0';
        hWr        <= '0';
        ram_hold   <= '0';
        ram_state  <= ram_state_0;
    end case;
 
    end if;
  end process;
 
  --
  -- SDRAM Address and data bus assignments
  --
  my_sdram_addr_data : process( cpu_addr, dat_addr,
                                cpu_data_out, hDout )
  begin
    hAddr(23 downto 19)  <= "00000";
    hAddr(18 downto 11)  <= dat_addr;
    hAddr(10 downto 0)   <= cpu_addr(11 downto 1);
    hUds                 <= not cpu_addr(0);
    hLds                 <=     cpu_addr(0);
    if cpu_addr(0) = '0' then
      hDin( 7 downto 0) <= (others=>'0');
      hDin(15 downto 8) <= cpu_data_out;
      ram_data_out      <= hDout(15 downto 8);
    else
      hDin( 7 downto 0) <= cpu_data_out;
      hDin(15 downto 8) <= (others=>'0');
      ram_data_out      <= hDout( 7 downto 0);
    end if;
  end process;
 
  --
  -- Hold RAM until falling CPU clock edge
  --
  ram_bus_hold: process( cpu_clk, cpu_reset, ram_hold )
  begin
    if ram_hold = '1' then
      ram_release   <= '0';
    elsif falling_edge(cpu_clk) then
      ram_release   <= '1';
    end if;
  end process;
 
  --
  -- CPU read data request on rising CPU clock edge
  --
  ram_read_request: process( hRd, cpu_clk, ram_cs, cpu_rw, ram_release )
  begin
    if hRd = '1' then
      ram_rd_req   <= '0';
    elsif rising_edge(cpu_clk) then
      if (ram_cs = '1') and (cpu_rw = '1') and (ram_release = '1') then
        ram_rd_req   <= '1';
      end if;
    end if;
  end process;
 
  --
  -- CPU write data to RAM valid on rising CPU clock edge
  --
  ram_write_request: process( hWr, cpu_clk, ram_cs, cpu_rw, ram_release )
  begin
    if hWr = '1' then
       ram_wr_req   <= '0';
    elsif rising_edge(cpu_clk) then
      if (ram_cs = '1') and (cpu_rw = '0') and (ram_release = '1') then
        ram_wr_req   <= '1';
      end if;
    end if;
  end process;
 
  status_leds : process( rst_i, cpu_reset, lock )
  begin
    S(0) <= rst_i;
    S(1) <= cpu_reset;
    S(2) <= lock;
    S(3) <= countL(23);
    S(7 downto 4) <= "0000";
  end process;
 
--  debug_proc : process( cpu_reset, cpu_clk, cpu_rw, cpu_vma,
--                      cpu_halt, cpu_hold,
--                      cpu_firq, cpu_irq, cpu_nmi,
--                      cpu_addr, cpu_data_out, cpu_data_in )
--  begin
--    cpu_reset_o    <= cpu_reset;
--    cpu_clk_o      <= cpu_clk;
--    cpu_rw_o       <= cpu_rw;
--    cpu_vma_o      <= cpu_vma;
--    cpu_halt_o     <= cpu_halt;
--    cpu_hold_o     <= cpu_hold;
--    cpu_firq_o     <= cpu_firq;
--    cpu_irq_o      <= cpu_irq;
--    cpu_nmi_o      <= cpu_nmi;
--    cpu_addr_o     <= cpu_addr;
--    cpu_data_out_o <= cpu_data_out;
--    cpu_data_in_o  <= cpu_data_in;
--  end process;
 
end rtl; --===================== End of architecture =======================--
 

Line No.	Rev	Author	Line
1	19	dilbert57	`--===========================================================================----`
2			`--`
3			`-- S Y N T H E Z I A B L E System09 - SOC.`
4			`--`
5			`-- www.OpenCores.Org - February 2007`
6			`-- This core adheres to the GNU public license`
7			`--`
8			`-- File name : System09_Xess_XSA-3S1000.vhd`
9			`--`
10			`-- Purpose : Top level file for 6809 compatible system on a chip`
11			`-- Designed with Xilinx XC3S1000 Spartan 3 FPGA.`
12			`-- Implemented With XESS XSA-3S1000 FPGA board.`
13			`-- * Note *`
14			`-- This configuration can run Flex9 however it only has`
15			`-- 32k bytes of user memory and the VDU is monochrome`
16			`-- The design needs to be updated to use the SDRAM on`
17			`-- the XSA-3S1000 board.`
18			`-- This configuration also lacks a DAT so cannot use`
19			`-- the RAM Disk features of SYS09BUG.`
20			`--`
21			`-- Dependencies : ieee.Std_Logic_1164`
22			`-- ieee.std_logic_unsigned`
23			`-- ieee.std_logic_arith`
24			`-- ieee.numeric_std`
25			`-- unisim.vcomponents`
26			`--`
27			`-- Uses : mon_rom (sys09bug_rom4k_b16.vhd) Sys09Bug Monitor ROM`
28			`-- cpu09 (cpu09.vhd) CPU core`
29	99	davidgb	`-- ACIA_6850 (acia6850.vhd) ACIA / UART`
30	19	dilbert57	`-- ACIA_Clock (ACIA_Clock.vhd) ACIA clock.`
31			`-- keyboard (keyboard.vhd) PS/2 Keyboard interface`
32			`-- (ps2_keyboard.vhd)`
33			`-- (keymap_rom_slice.vhd) Key map table`
34			`-- vdu8_mono (vdu8_mono.vhd) Monochrome VDU`
35			`-- (char_rom2k_b16.vhd)`
36			`-- (ram2k_b16.vhd)`
37			`-- timer (timer.vhd) Interrupt timer`
38			`-- trap (trap.vhd) Bus condition trap logic`
39			`-- flex_ram (flex9_ram8k_b16.vhd) Flex operating system`
40			`-- ram_32K (ram32k_b16.vhd) 32 KBytes of Block RAM`
41			`--`
42			`--`
43			`-- Author : John E. Kent`
44			`-- dilbert57@opencores.org`
45			`--`
46			`-- Memory Map :`
47			`--`
48			`-- $0000 - User program RAM (32K Bytes)`
49			`-- $C000 - Flex Operating System memory (8K Bytes)`
50			`-- $E000 - ACIA (SWTPc)`
51			`-- $E010 - Reserved for FD1771 FDC (SWTPc)`
52			`-- $E020 - Keyboard`
53			`-- $E030 - VDU`
54			`-- $E040 - IDE / Compact Flash interface`
55			`-- $E050 - Timer`
56			`-- $E060 - Bus trap`
57			`-- $E070 - Reserced for Parallel I/O (B5-X300)`
58			`-- $E080 - Reserved for 6821 PIA (?) (SWTPc)`
59			`-- $E090 - Reserved for 6840 PTM (?) (SWTPc)`
60			`-- $F000 - Sys09Bug monitor Program (4K Bytes)`
61			`--`
62			`--===========================================================================----`
63			`--`
64			`-- Revision History:`
65			`--===========================================================================--`
66			`-- Version 0.1 - 20 March 2003`
67			`-- Version 0.2 - 30 March 2003`
68			`-- Version 0.3 - 29 April 2003`
69			`-- Version 0.4 - 29 June 2003`
70			`--`
71			`-- Version 0.5 - 19 July 2003`
72			`-- prints out "Hello World"`
73			`--`
74			`-- Version 0.6 - 5 September 2003`
75			`-- Runs SBUG`
76			`--`
77			`-- Version 1.0- 6 Sep 2003 - John Kent`
78			`-- Inverted SysClk`
79			`-- Initial release to Open Cores`
80			`--`
81			`-- Version 1.1 - 17 Jan 2004 - John Kent`
82			`-- Updated miniUart.`
83			`--`
84			`-- Version 1.2 - 25 Jan 2004 - John Kent`
85			`-- removed signals "test_alu" and "test_cc"`
86			`-- Trap hardware re-instated.`
87			`--`
88			`-- Version 1.3 - 11 Feb 2004 - John Kent`
89			`-- Designed forked off to produce System09_VDU`
90			`-- Added VDU component`
91	134	davidgb	`-- VDU runs at 25MHz and divides the clock by 2 for the CPU`
92	19	dilbert57	`-- UART Runs at 57.6 Kbps`
93			`--`
94			`-- Version 2.0 - 2 September 2004 - John Kent`
95			`-- ported to Digilent Xilinx Spartan3 starter board`
96	134	davidgb	`-- removed Compact Flash and Trap Logic.`
97	19	dilbert57	`-- Replaced SBUG with KBug9s`
98			`--`
99			`-- Version 3.0 - 29th August 2006 - John Kent`
100			`-- Adapted to XSA-3S1000 board.`
101			`-- Removed DAT and miniUART.`
102			`-- Used 32KBytes of Block RAM.`
103			`--`
104			`-- Version 3.1 - 15th January 2007 - John Kent`
105			`-- Modified vdu8 interface`
106			`-- Added a clock divider`
107			`--`
108			`-- Version 3.2 - 25th February 2007 - John Kent`
109			`-- reinstated ACIA_6850 and ACIA_Clock`
110			`-- Updated VDU8 & Keyboard with generic parameters`
111			`-- Defined Constants for clock speed calculations`
112			`--`
113			`-- Version 3.3 - 1st July 2007 - John Kent`
114			`-- Made VDU mono to save on one RAMB16`
115			`-- Used distributed memory for Key Map ROM to save one RAMB16`
116			`-- Added Flex RAM at $C000 to $DFFF using 4 spare RAMB16s`
117			`-- Added timer and trap logic`
118			`-- Added IDE Interface for Compact Flash`
119			`-- Replaced KBug9s and stack with Sys09Bug.`
120			`--`
121	22	dilbert57	`-- Version 4.0 - 1st February 2008 - John kent`
122			`-- Replaced Block RAM with SDRAM Interface`
123			`-- Modified Hold timing for SDRAM`
124			`-- Added CF and Ethernet interface`
125			`-- via the 16 bit peripheral bus at $E100`
126			`--`
127	19	dilbert57	`--===========================================================================--`
128			`library ieee;`
129			`use ieee.std_logic_1164.all;`
130			`use IEEE.STD_LOGIC_ARITH.ALL;`
131			`use IEEE.STD_LOGIC_UNSIGNED.ALL;`
132			`use ieee.numeric_std.all;`
133	22	dilbert57	`library work;`
134	134	davidgb	`use work.common.all;`
135			`use WORK.xsasdram.all;`
136	19	dilbert57	`library unisim;`
137			`use unisim.vcomponents.all;`
138
139	114	davidgb	`entity system09 is`
140	19	dilbert57	`port(`
141	115	davidgb	`CLKA : in Std_Logic; -- 100MHz Clock input`
142			`-- CLKB : in Std_Logic; -- 50MHz Clock input`
143	134	davidgb	`SW2_N : in Std_logic; -- Master Reset input (active low)`
144			`SW3_N : in Std_logic; -- Non Maskable Interrupt input (active low)`
145	19	dilbert57
146	134	davidgb	`-- PS/2 Keyboard`
147			`ps2_clk : inout Std_logic;`
148			`ps2_dat : inout Std_Logic;`
149	19	dilbert57
150	134	davidgb	`-- CRTC output signals`
151			`vga_vsync_n : out Std_Logic;`
152	22	dilbert57	`vga_hsync_n : out Std_Logic;`
153			`vga_blue : out std_logic_vector(2 downto 0);`
154			`vga_green : out std_logic_vector(2 downto 0);`
155			`vga_red : out std_logic_vector(2 downto 0);`
156	19	dilbert57
157			`-- RS232 Port`
158	134	davidgb	`RS232_RXD : in Std_Logic;`
159			`RS232_TXD : out Std_Logic;`
160	22	dilbert57	`RS232_CTS : in Std_Logic;`
161			`RS232_RTS : out Std_Logic;`
162	19	dilbert57
163	134	davidgb	`-- Status 7 segment LED`
164			`S : out std_logic_vector(7 downto 0);`
165	19	dilbert57
166	22	dilbert57	`-- SDRAM side`
167			`SDRAM_clkfb : in std_logic; -- feedback SDRAM clock after PCB delays`
168			`SDRAM_clkout : out std_logic; -- clock to SDRAM`
169			`SDRAM_CKE : out std_logic; -- clock-enable to SDRAM`
170			`SDRAM_CS_N : out std_logic; -- chip-select to SDRAM`
171			`SDRAM_RAS_N : out std_logic; -- SDRAM row address strobe`
172			`SDRAM_CAS_N : out std_logic; -- SDRAM column address strobe`
173			`SDRAM_WE_N : out std_logic; -- SDRAM write enable`
174			`SDRAM_BA : out std_logic_vector(1 downto 0); -- SDRAM bank address`
175			`SDRAM_A : out std_logic_vector(12 downto 0); -- SDRAM row/column address`
176			`SDRAM_D : inout std_logic_vector(15 downto 0); -- data from SDRAM`
177			`SDRAM_DQMH : out std_logic; -- enable upper-byte of SDRAM databus if true`
178			`SDRAM_DQML : out std_logic; -- enable lower-byte of SDRAM databus if true`
179
180	134	davidgb	`-- Peripheral I/O bus $E100 - $E1FF`
181	22	dilbert57	`PB_RD_N : out std_logic;`
182			`PB_WR_N : out std_logic;`
183			`PB_A : out std_logic_vector(4 downto 0);`
184			`PB_D : inout std_logic_vector(15 downto 0);`
185
186			`-- IDE Compact Flash $E100 - $E13F`
187			`ide_dmack_n : out std_logic;`
188	134	davidgb	`ide_cs0_n : out std_logic;`
189			`ide_cs1_n : out std_logic;`
190	22	dilbert57
191			`-- Ethernet $E140 - $E17F`
192	115	davidgb	`ether_cs_n : out std_logic;`
193	22	dilbert57	`ether_aen : out std_logic; -- Ethernet address enable not`
194			`ether_bhe_n : out std_logic; -- Ethernet bus high enable`
195			`ether_clk : in std_logic; -- Ethernet clock`
196			`ether_rdy : in std_logic; -- Ethernet ready`
197	115	davidgb	`ether_irq : in std_logic; -- Ethernet irq - Shared with BAR6`
198	22	dilbert57
199			`-- Slot 1 $E180 - $E1BF`
200	134	davidgb	`slot1_cs_n : out std_logic;`
201			`-- slot1_irq : in std_logic;`
202	22	dilbert57
203			`-- Slot 2 $E1C0 - $E1FF`
204	134	davidgb	`slot2_cs_n : out std_logic;`
205			`-- slot2_irq : in std_logic;`
206
207	115	davidgb	`-- CPU Debug Interface signals`
208			`-- cpu_reset_o : out Std_Logic;`
209			`-- cpu_clk_o : out Std_Logic;`
210			`-- cpu_rw_o : out std_logic;`
211			`-- cpu_vma_o : out std_logic;`
212			`-- cpu_halt_o : out std_logic;`
213			`-- cpu_hold_o : out std_logic;`
214			`-- cpu_firq_o : out std_logic;`
215			`-- cpu_irq_o : out std_logic;`
216			`-- cpu_nmi_o : out std_logic;`
217			`-- cpu_addr_o : out std_logic_vector(15 downto 0);`
218			`-- cpu_data_in_o : out std_logic_vector(7 downto 0);`
219			`-- cpu_data_out_o : out std_logic_vector(7 downto 0);`
220	22	dilbert57
221	134	davidgb	`-- Disable Flash`
222			`FLASH_CE_N : out std_logic`
223			`);`
224	114	davidgb	`end system09;`
225	19	dilbert57
226			`-------------------------------------------------------------------------------`
227			`-- Architecture for System09`
228			`-------------------------------------------------------------------------------`
229	114	davidgb	`architecture rtl of system09 is`
230	19	dilbert57
231			`-----------------------------------------------------------------------------`
232			`-- constants`
233	134	davidgb	`-----------------------------------------------------------------------------`
234
235	115	davidgb	`-- SDRAM`
236			`constant MEM_CLK_FREQ : natural := 100_000; -- operating frequency of Memory in KHz`
237			`constant SYS_CLK_DIV : real := 2.0; -- divisor for FREQ (can only be 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0, 8.0 or 16.0)`
238			`constant PIPE_EN : boolean := false; -- if true, enable pipelined read operations`
239			`constant MAX_NOP : natural := 10000; -- number of NOPs before entering self-refresh`
240			`constant MULTIPLE_ACTIVE_ROWS : boolean := false; -- if true, allow an active row in each bank`
241			`constant DATA_WIDTH : natural := 16; -- host & SDRAM data width`
242			`constant NROWS : natural := 8192; -- number of rows in SDRAM array`
243			`constant NCOLS : natural := 512; -- number of columns in SDRAM array`
244			`constant HADDR_WIDTH : natural := 24; -- host-side address width`
245			`constant SADDR_WIDTH : natural := 13; -- SDRAM-side address width`
246	19	dilbert57
247	115	davidgb	`constant SYS_CLK_FREQ : natural := ((MEM_CLK_FREQ2)/integer(SYS_CLK_DIV2.0))*1000; -- FPGA System Clock`
248	134	davidgb	`constant CPU_CLK_FREQ : natural := 25_000_000; -- CPU Clock (Hz)`
249	115	davidgb	`constant CPU_CLK_DIV : natural := (SYS_CLK_FREQ/CPU_CLK_FREQ);`
250			`constant VGA_CLK_FREQ : natural := 25_000_000; -- VGA Pixel Clock`
251			`constant VGA_CLK_DIV : natural := ((MEM_CLK_FREQ*1000)/VGA_CLK_FREQ);`
252	134	davidgb	`constant BAUD_RATE : integer := 57600; -- Baud Rate`
253			`constant ACIA_CLK_FREQ : integer := BAUD_RATE * 16;`
254
255			`constant TRESET : natural := 300; -- min initialization interval (us)`
256	115	davidgb	`constant RST_CYCLES : natural := 1+(TRESET*(MEM_CLK_FREQ/1_000)); -- SDRAM power-on initialization interval`
257
258	19	dilbert57	`type hold_state_type is ( hold_release_state, hold_request_state );`
259
260			`-----------------------------------------------------------------------------`
261			`-- Signals`
262			`-----------------------------------------------------------------------------`
263			`-- BOOT ROM`
264			`signal rom_cs : Std_logic;`
265			`signal rom_data_out : Std_Logic_Vector(7 downto 0);`
266
267			`-- Flex Memory & Monitor Stack`
268			`signal flex_cs : Std_logic;`
269			`signal flex_data_out : Std_Logic_Vector(7 downto 0);`
270
271			`-- ACIA/UART Interface signals`
272	22	dilbert57	`signal acia_data_out : Std_Logic_Vector(7 downto 0);`
273			`signal acia_cs : Std_Logic;`
274			`signal acia_irq : Std_Logic;`
275			`signal acia_clk : Std_Logic;`
276	19	dilbert57	`signal rxd : Std_Logic;`
277			`signal txd : Std_Logic;`
278			`signal DCD_n : Std_Logic;`
279			`signal RTS_n : Std_Logic;`
280			`signal CTS_n : Std_Logic;`
281
282			`-- keyboard port`
283			`signal keyboard_data_out : std_logic_vector(7 downto 0);`
284			`signal keyboard_cs : std_logic;`
285			`signal keyboard_irq : std_logic;`
286
287			`-- RAM`
288			`signal ram_cs : std_logic; -- memory chip select`
289			`signal ram_data_out : std_logic_vector(7 downto 0);`
290	134	davidgb	`signal ram_rd_req : std_logic; -- ram read request (asynch set on ram read, cleared falling CPU clock edge)`
291	115	davidgb	`signal ram_wr_req : std_logic; -- ram write request (set on rising CPU clock edge, asynch clear on acknowledge)`
292	22	dilbert57	`signal ram_hold : std_logic; -- hold off slow accesses`
293	115	davidgb	`signal ram_release : std_logic; -- Release ram hold`
294	19	dilbert57
295			`-- CPU Interface signals`
296			`signal cpu_reset : Std_Logic;`
297			`signal cpu_clk : Std_Logic;`
298			`signal cpu_rw : std_logic;`
299			`signal cpu_vma : std_logic;`
300			`signal cpu_halt : std_logic;`
301			`signal cpu_hold : std_logic;`
302			`signal cpu_firq : std_logic;`
303			`signal cpu_irq : std_logic;`
304			`signal cpu_nmi : std_logic;`
305			`signal cpu_addr : std_logic_vector(15 downto 0);`
306			`signal cpu_data_in : std_logic_vector(7 downto 0);`
307			`signal cpu_data_out : std_logic_vector(7 downto 0);`
308
309	22	dilbert57	`-- Dynamic Address Translation`
310			`signal dat_cs : std_logic;`
311			`signal dat_addr : std_logic_vector(7 downto 0);`
312
313	19	dilbert57	`-- Video Display Unit`
314			`signal vdu_cs : std_logic;`
315			`signal vdu_data_out : std_logic_vector(7 downto 0);`
316			`signal vga_red_o : std_logic;`
317			`signal vga_green_o : std_logic;`
318			`signal vga_blue_o : std_logic;`
319
320			`-- timer`
321			`signal timer_data_out : std_logic_vector(7 downto 0);`
322			`signal timer_cs : std_logic;`
323			`signal timer_irq : std_logic;`
324
325			`-- trap`
326			`signal trap_cs : std_logic;`
327			`signal trap_data_out : std_logic_vector(7 downto 0);`
328			`signal trap_irq : std_logic;`
329
330	22	dilbert57	`-- Peripheral Bus port`
331			`signal pb_data_out : std_logic_vector(7 downto 0);`
332	134	davidgb	`signal pb_cs : std_logic; -- peripheral bus chip select`
333			`signal pb_wru : std_logic; -- upper byte write strobe`
334			`signal pb_wrl : std_logic; -- lower byte write strobe`
335			`signal pb_rdu : std_logic; -- upper byte read strobe`
336			`signal pb_rdl : std_logic; -- lower byte read strobe`
337			`signal pb_hold : std_logic; -- hold peripheral bus access`
338			`signal pb_release : std_logic; -- release hold of peripheral bus`
339	22	dilbert57	`signal pb_count : std_logic_vector(3 downto 0); -- hold counter`
340			`signal pb_hold_state : hold_state_type;`
341			`signal pb_wreg : std_logic_vector(7 downto 0); -- lower byte write register`
342			`signal pb_rreg : std_logic_vector(7 downto 0); -- lower byte read register`
343	19	dilbert57
344	22	dilbert57	`-- Peripheral chip selects on Peripheral Bus`
345			`signal ide_cs : std_logic; -- IDE CF interface`
346	134	davidgb	`signal ether_cs : std_logic; -- Ethernet interface`
347			`signal slot1_cs : std_logic; -- Expansion slot 1`
348			`signal slot2_cs : std_logic; -- Expansion slot 2`
349	22	dilbert57
350	115	davidgb	`signal rst_i : std_logic; -- internal reset signal`
351			`signal clk_i : std_logic; -- internal master clock signal`
352			`signal lock : std_logic; -- SDRAM clock DLL lock indicator`
353	22	dilbert57
354			`-- signals that go through the SDRAM host-side interface`
355	115	davidgb	`signal opBegun : std_logic; -- SDRAM operation started indicator`
356			`signal earlyBegun : std_logic; -- SDRAM operation started indicator`
357			`signal ramDone : std_logic; -- SDRAM operation complete indicator`
358			`signal rdDone : std_logic; -- SDRAM read operation complete indicator`
359			`signal wrDone : std_logic; -- SDRAM write operation complete indicator`
360			`signal hAddr : std_logic_vector(HADDR_WIDTH-1 downto 0); -- host address bus`
361			`signal hDIn : std_logic_vector(DATA_WIDTH-1 downto 0); -- host-side data to SDRAM`
362			`signal hDOut : std_logic_vector(DATA_WIDTH-1 downto 0); -- host-side data from SDRAM`
363			`signal hRd : std_logic; -- host-side read control signal`
364			`signal hWr : std_logic; -- host-side write control signal`
365	134	davidgb	`signal hUds : std_logic; -- host-side upper data strobe`
366			`signal hLds : std_logic; -- host-side lower data strobe`
367	115	davidgb	`signal rdPending : std_logic; -- read operation pending in SDRAM pipeline`
368	134	davidgb	`type ram_type is (ram_state_0,`
369			`ram_state_rd1, ram_state_rd2,`
370			`ram_state_wr1,`
371			`ram_state_3 );`
372	115	davidgb	`signal ram_state : ram_type;`
373	22	dilbert57
374	115	davidgb	`signal CountL : std_logic_vector(23 downto 0);`
375			`signal clk_count : natural range 0 to CPU_CLK_DIV;`
376			`signal Clk25 : std_logic;`
377			`signal vga_clk : std_logic;`
378	19	dilbert57
379			`-----------------------------------------------------------------`
380			`--`
381			`-- CPU09 CPU core`
382			`--`
383			`-----------------------------------------------------------------`
384
385			`component cpu09`
386			`port (`
387	134	davidgb	`clk: in std_logic;`
388			`rst: in std_logic;`
389			`vma: out std_logic;`
390			`addr: out std_logic_vector(15 downto 0);`
391			`rw: out std_logic; -- Asynchronous memory interface`
392			`data_out: out std_logic_vector(7 downto 0);`
393			`data_in: in std_logic_vector(7 downto 0);`
394			`irq: in std_logic;`
395			`firq: in std_logic;`
396			`nmi: in std_logic;`
397			`halt: in std_logic;`
398			`hold: in std_logic`
399	19	dilbert57	`);`
400			`end component;`
401
402			`----------------------------------------`
403			`--`
404			`-- 4K Block RAM Monitor ROM`
405	134	davidgb	`-- $F000 - $FFFF`
406	19	dilbert57	`--`
407			`----------------------------------------`
408	134	davidgb
409	19	dilbert57	`component mon_rom`
410	134	davidgb	`Port (`
411			`clk : in std_logic;`
412			`rst : in std_logic;`
413			`cs : in std_logic;`
414			`rw : in std_logic;`
415			`addr : in std_logic_vector (11 downto 0);`
416			`data_out : out std_logic_vector (7 downto 0);`
417			`data_in : in std_logic_vector (7 downto 0)`
418			`);`
419	19	dilbert57	`end component;`
420
421			`----------------------------------------`
422			`--`
423			`-- 8KBytes Block RAM for FLEX9`
424			`-- $C000 - $DFFF`
425			`--`
426			`----------------------------------------`
427	134	davidgb
428	19	dilbert57	`component flex_ram`
429			`Port (`
430			`clk : in std_logic;`
431			`rst : in std_logic;`
432			`cs : in std_logic;`
433			`rw : in std_logic;`
434			`addr : in std_logic_vector (12 downto 0);`
435	95	davidgb	`data_out : out std_logic_vector (7 downto 0);`
436			`data_in : in std_logic_vector (7 downto 0)`
437	134	davidgb	`);`
438	19	dilbert57	`end component;`
439
440			`-----------------------------------------------------------------`
441			`--`
442			`-- 6850 Compatible ACIA / UART`
443			`--`
444			`-----------------------------------------------------------------`
445
446	99	davidgb	`component acia6850`
447	19	dilbert57	`port (`
448	134	davidgb	`clk : in Std_Logic; -- System Clock`
449			`rst : in Std_Logic; -- Reset input (active high)`
450			`cs : in Std_Logic; -- miniUART Chip Select`
451			`rw : in Std_Logic; -- Read / Not Write`
452			`addr : in Std_Logic; -- Register Select`
453			`data_in : in Std_Logic_Vector(7 downto 0); -- Data Bus In`
454			`data_out : out Std_Logic_Vector(7 downto 0); -- Data Bus Out`
455			`irq : out Std_Logic; -- Interrupt`
456			`RxC : in Std_Logic; -- Receive Baud Clock`
457			`TxC : in Std_Logic; -- Transmit Baud Clock`
458			`RxD : in Std_Logic; -- Receive Data`
459			`TxD : out Std_Logic; -- Transmit Data`
460			`DCD_n : in Std_Logic; -- Data Carrier Detect`
461			`CTS_n : in Std_Logic; -- Clear To Send`
462			`RTS_n : out Std_Logic -- Request To send`
463			`);`
464	19	dilbert57	`end component;`
465
466			`-----------------------------------------------------------------`
467			`--`
468			`-- ACIA Clock divider`
469			`--`
470			`-----------------------------------------------------------------`
471
472			`component ACIA_Clock`
473			`generic (`
474	134	davidgb	`SYS_CLK_FREQ : integer := SYS_CLK_FREQ;`
475			`ACIA_CLK_FREQ : integer := ACIA_CLK_FREQ`
476	19	dilbert57	`);`
477			`port (`
478	134	davidgb	`clk : in Std_Logic; -- System Clock Input`
479			`ACIA_clk : out Std_logic -- ACIA Clock output`
480	19	dilbert57	`);`
481			`end component;`
482
483			`----------------------------------------`
484			`--`
485			`-- PS/2 Keyboard`
486			`--`
487			`----------------------------------------`
488
489			`component keyboard`
490			`generic(`
491	134	davidgb	`KBD_CLK_FREQ : integer := CPU_CLK_FREQ`
492	19	dilbert57	`);`
493			`port(`
494	134	davidgb	`clk : in std_logic;`
495			`rst : in std_logic;`
496			`cs : in std_logic;`
497			`rw : in std_logic;`
498			`addr : in std_logic;`
499			`data_in : in std_logic_vector(7 downto 0);`
500			`data_out : out std_logic_vector(7 downto 0);`

Browse

Tools

Subversion Repositories System09

[/] [System09/] [trunk/] [rtl/] [System09_Xess_XSA-3S1000/] [System09_Xess_XSA-3S1000.vhd] - Blame information for rev 223