URL https://opencores.org/ocsvn/System09/System09/trunk
Subversion Repositories System09

[/] [System09/] [trunk/] [rtl/] [System09_Xilinx_ML506/] [System09_Xilinx_ML506.vhd] - Blame information for rev 141

Go to most recent revision | Details | Compare with Previous | View Log

--===========================================================================----
--
--  S Y N T H E Z I A B L E    System09 - SOC.
--
--  www.OpenCores.Org - February 2007
--  This core adheres to the GNU public license  
--
-- File name      : System09_Xilinx_ML506.vhd
--
-- Purpose        : Top level file for 6809 compatible system on a chip
--                  Designed with Xilinx Virtex-5.
--                  Implemented With Xilinx ML506 FPGA board.
--                  *** Note ***
--                  This configuration can run Flex9 however it only has
--                  32k bytes of user memory and the VDU is monochrome
--                  This configuration also lacks a DAT so cannot use
--                  the RAM Disk features of SYS09BUG.
--
-- Dependencies   : ieee.Std_Logic_1164
--                  ieee.std_logic_unsigned
--                  ieee.std_logic_arith
--                  ieee.numeric_std
--                  unisim.vcomponents
--
-- Uses           : mon_rom    (sys09bug_rom4k_b16.vhd) Sys09Bug Monitor ROM
--                  cpu09      (cpu09.vhd)          CPU core
--                  ACIA_6850  (acia6850.vhd)      ACIA / UART
--                  ACIA_Clock (ACIA_Clock.vhd)      ACIA clock.
--                  keyboard   (keyboard.vhd)        PS/2 Keyboard interface
--                             (ps2_keyboard.vhd)
--                             (keymap_rom_slice.vhd) Key map table 
--                  vdu8_mono  (vdu8_mono.vhd)        Monochrome VDU
--                             (char_rom2k_b16.vhd)
--                             (ram2k_b16.vhd)
--                  timer      (timer.vhd)            Interrupt timer
--                  trap       (trap.vhd)             Bus condition trap logic
--                  flex_ram   (flex9_ram8k_b16.vhd)  Flex operating system
--                  ram_32K    (ram32k_b16.vhd)       32 KBytes of Block RAM
--                  
-- 
-- Author         : John E. Kent      
--                  dilbert57@opencores.org      
--
-- Memory Map     :
--
-- $0000 - User program RAM (32K Bytes)
-- $C000 - Flex Operating System memory (8K Bytes)
-- $E000 - ACIA (SWTPc)
-- $E010 - Reserved for FD1771 FDC (SWTPc)
-- $E020 - Keyboard
-- $E030 - VDU
-- $E040 - IDE / Compact Flash interface
-- $E050 - Timer
-- $E060 - Bus trap
-- $E070 - Reserced for Parallel I/O (B5-X300)
-- $E080 - Reserved for 6821 PIA (?) (SWTPc)
-- $E090 - Reserved for 6840 PTM (?) (SWTPc)
-- $F000 - Sys09Bug monitor Program (4K Bytes)
--
--===========================================================================----
--
-- Revision History:
--===========================================================================--
-- Version 0.1 - 20 March 2003
-- Version 0.2 - 30 March 2003
-- Version 0.3 - 29 April 2003
-- Version 0.4 - 29 June 2003
--
-- Version 0.5 - 19 July 2003
-- prints out "Hello World"
--
-- Version 0.6 - 5 September 2003
-- Runs SBUG
--
-- Version 1.0- 6 Sep 2003 - John Kent
-- Inverted SysClk
-- Initial release to Open Cores
--
-- Version 1.1 - 17 Jan 2004 - John Kent
-- Updated miniUart.
--
-- Version 1.2 - 25 Jan 2004 - John Kent
-- removed signals "test_alu" and "test_cc" 
-- Trap hardware re-instated.
--
-- Version 1.3 - 11 Feb 2004 - John Kent
-- Designed forked off to produce System09_VDU
-- Added VDU component
--      VDU runs at 25MHz and divides the clock by 2 for the CPU
-- UART Runs at 57.6 Kbps
--
-- Version 2.0 - 2 September 2004 - John Kent
-- ported to Digilent Xilinx Spartan3 starter board
--      removed Compact Flash and Trap Logic.
-- Replaced SBUG with KBug9s
--
-- Version 3.0 - 29th August 2006 - John Kent
-- Adapted to XSA-3S1000 board.
-- Removed DAT and miniUART.
-- Used 32KBytes of Block RAM.
--
-- Version 3.1 - 15th January 2007 - John Kent
-- Modified vdu8 interface
-- Added a clock divider
--
-- Version 3.2 - 25th February 2007 - John Kent
-- reinstated ACIA_6850 and ACIA_Clock
-- Updated VDU8 & Keyboard with generic parameters
-- Defined Constants for clock speed calculations
--
-- Version 3.3 - 1st July 2007 - John Kent
-- Made VDU mono to save on one RAMB16
-- Used distributed memory for Key Map ROM to save one RAMB16
-- Added Flex RAM at $C000 to $DFFF using 4 spare RAMB16s
-- Added timer and trap logic
-- Added IDE Interface for Compact Flash
-- Replaced KBug9s and stack with Sys09Bug.
--
-- Version 4.0 - 1st February 2008 - John kent
-- Replaced Block RAM with SDRAM Interface
-- Modified Hold timing for SDRAM
-- Added CF and Ethernet interface 
-- via the 16 bit peripheral bus at $E100
--
--===========================================================================--
library ieee;
   use ieee.std_logic_1164.all;
   use IEEE.STD_LOGIC_ARITH.ALL;
   use IEEE.STD_LOGIC_UNSIGNED.ALL;
   use ieee.numeric_std.all;
library unisim;
   use unisim.vcomponents.all;
 
entity system09 is
  port(
    clk_i         : in  Std_Logic;  -- 100MHz Clock input
--    CLKB         : in  Std_Logic;  -- 50MHz Clock input
         SW2_N        : in  Std_logic;  -- Master Reset input (active low)
         SW3_N        : in  Std_logic;  -- Non Maskable Interrupt input (active low)
 
         -- PS/2 Keyboard
--       ps2_clk      : inout Std_logic;
--       ps2_dat      : inout Std_Logic;
 
         -- CRTC output signals
--       vga_vsync_n  : out Std_Logic;
--    vga_hsync_n  : out Std_Logic;
--    vga_blue     : out std_logic_vector(2 downto 0);
--    vga_green    : out std_logic_vector(2 downto 0);
--    vga_red      : out std_logic_vector(2 downto 0);
 
    -- RS232 Port
         RS232_RXD    : in  Std_Logic;
         RS232_TXD    : out Std_Logic;
--    RS232_CTS    : in  Std_Logic;
--    RS232_RTS    : out Std_Logic;
 
 
 
    -- SDRAM side
--    SDRAM_clkfb  : in  std_logic;            -- feedback SDRAM clock after PCB delays
--    SDRAM_clkout : out std_logic;            -- clock to SDRAM
--    SDRAM_CKE    : out std_logic;            -- clock-enable to SDRAM
--    SDRAM_CS_N   : out std_logic;            -- chip-select to SDRAM
--    SDRAM_RAS_N  : out std_logic;            -- SDRAM row address strobe
--    SDRAM_CAS_N  : out std_logic;            -- SDRAM column address strobe
--    SDRAM_WE_N   : out std_logic;            -- SDRAM write enable
--    SDRAM_BA     : out std_logic_vector(1 downto 0);  -- SDRAM bank address
--    SDRAM_A      : out std_logic_vector(12 downto 0);  -- SDRAM row/column address
--    SDRAM_D      : inout  std_logic_vector(15 downto 0);  -- data from SDRAM
--    SDRAM_DQMH   : out std_logic;            -- enable upper-byte of SDRAM databus if true
--    SDRAM_DQML   : out std_logic;            -- enable lower-byte of SDRAM databus if true
 
         -- Peripheral I/O bus $E100 - $E1FF
--    PB_RD_N      : out std_logic;
--    PB_WR_N      : out std_logic;
--    PB_A         : out std_logic_vector(4 downto 0);
--    PB_D         : inout std_logic_vector(15 downto 0);
 
    -- IDE Compact Flash $E100 - $E13F
--    ide_dmack_n  : out std_logic;
--       ide_cs0_n    : out std_logic;
--       ide_cs1_n    : out std_logic;
 
    -- Ethernet $E140 - $E17F
--    ether_cs_n   : out std_logic;
--    ether_aen    : out std_logic; -- Ethernet address enable not 
--    ether_bhe_n  : out std_logic; -- Ethernet bus high enable 
--    ether_clk    : in  std_logic; -- Ethernet clock 
--    ether_rdy    : in  std_logic; -- Ethernet ready
--    ether_irq    : in  std_logic; -- Ethernet irq - Shared with BAR6
 
    -- Slot 1 $E180 - $E1BF
--       slot1_cs_n   : out std_logic;
--       slot1_irq    : in  std_logic;
 
    -- Slot 2 $E1C0 - $E1FF
--       slot2_cs_n   : out std_logic;
--       slot2_irq    : in  std_logic;
 
-- CPU Debug Interface signals
--    cpu_reset_o     : out Std_Logic;
--    cpu_clk_o       : out Std_Logic;
--    cpu_rw_o        : out std_logic;
--    cpu_vma_o       : out std_logic;
--    cpu_halt_o      : out std_logic;
--    cpu_hold_o      : out std_logic;
--    cpu_firq_o      : out std_logic;
--    cpu_irq_o       : out std_logic;
--    cpu_nmi_o       : out std_logic;
--    cpu_addr_o      : out std_logic_vector(15 downto 0);
--    cpu_data_in_o   : out std_logic_vector(7 downto 0);
--    cpu_data_out_o  : out std_logic_vector(7 downto 0);
 
         -- Disable Flash
--       FLASH_CE_N   : out std_logic
         -- Status 7 segment LED
         S            : out std_logic_vector(7 downto 0)
         );
end system09;
 
-------------------------------------------------------------------------------
-- Architecture for System09
-------------------------------------------------------------------------------
architecture rtl of system09 is
 
  -----------------------------------------------------------------------------
  -- constants
  -----------------------------------------------------------------------------
 
  -- SDRAM
  constant MEM_CLK_FREQ         : natural := 100_000; -- operating frequency of Memory in KHz
  constant SYS_CLK_DIV          : real    := 2.0;    -- divisor for FREQ (can only be 1.0, 1.5, 2.0, 2.5, 3.0, 4.0, 5.0, 8.0 or 16.0)
  constant PIPE_EN              : boolean := false;  -- if true, enable pipelined read operations
  constant MAX_NOP              : natural := 10000;  -- number of NOPs before entering self-refresh
  constant MULTIPLE_ACTIVE_ROWS : boolean := false;  -- if true, allow an active row in each bank
  constant DATA_WIDTH           : natural := 16;     -- host & SDRAM data width
  constant NROWS                : natural := 8192;   -- number of rows in SDRAM array
  constant NCOLS                : natural := 512;    -- number of columns in SDRAM array
  constant HADDR_WIDTH          : natural := 24;     -- host-side address width
  constant SADDR_WIDTH          : natural := 13;     -- SDRAM-side address width
 
  constant SYS_CLK_FREQ         : natural := ((MEM_CLK_FREQ*2)/integer(SYS_CLK_DIV*2.0))*1000;  -- FPGA System Clock
  constant CPU_CLK_FREQ         : natural := 25_000_000;  -- CPU Clock (Hz)
  constant CPU_CLK_DIV          : natural := (SYS_CLK_FREQ/CPU_CLK_FREQ);
  constant VGA_CLK_FREQ         : natural := 25_000_000;  -- VGA Pixel Clock
  constant VGA_CLK_DIV          : natural := ((MEM_CLK_FREQ*1000)/VGA_CLK_FREQ);
  constant BAUD_RATE            : integer := 57600;       -- Baud Rate
  constant ACIA_CLK_FREQ        : integer := BAUD_RATE * 16;
 
  constant TRESET               : natural := 300;      -- min initialization interval (us)
  constant RST_CYCLES           : natural := 1+(TRESET*(MEM_CLK_FREQ/1_000));  -- SDRAM power-on initialization interval
 
  type hold_state_type is ( hold_release_state, hold_request_state );
 
 
-- Dummy signals to replace unused ports
signal   FLASH_CE_N   : std_logic;
signal ps2_clk, ps2_dat : std_logic;
signal ether_cs_n, ether_aen, ether_bhe_n, ether_clk, ether_rdy, ether_irq : std_logic;
signal slot1_cs_n, slot1_irq, slot2_cs_n, slot2_irq : std_logic;
signal SDRAM_clkfb, SDRAM_clkout, SDRAM_CKE, SDRAM_CS_N, SDRAM_RAS_N, SDRAM_WE_N, SDRAM_DQMH, SDRAM_DQML : std_logic;
signal SDRAM_BA : std_logic_vector(1 downto 0);
signal SDRAM_A : std_logic_vector(12 downto 0);
signal SDRAM_D : std_logic_vector(15 downto 0);
signal PB_RD_N, PB_WR_N : std_logic;
signal PB_A : std_logic_vector(4 downto 0);
signal PB_D : std_logic_vector(15 downto 0);
signal ide_dmack_n, ide_cs0_n, ide_cs1_n: std_logic;
signal vga_vsync_n, vga_hsync_n : std_logic;
signal vga_blue, vga_green, vga_red : std_logic_vector(2 downto 0);
signal RS232_CTS, RS232_RTS : std_logic;
 
  -----------------------------------------------------------------------------
  -- Signals
  -----------------------------------------------------------------------------
  -- BOOT ROM
  signal rom_cs         : Std_logic;
  signal rom_data_out   : Std_Logic_Vector(7 downto 0);
 
  -- Flex Memory & Monitor Stack
  signal flex_cs        : Std_logic;
  signal flex_data_out  : Std_Logic_Vector(7 downto 0);
 
  -- ACIA/UART Interface signals
  signal acia_data_out  : Std_Logic_Vector(7 downto 0);
  signal acia_cs        : Std_Logic;
  signal acia_irq       : Std_Logic;
  signal acia_clk       : Std_Logic;
  signal rxd            : Std_Logic;
  signal txd            : Std_Logic;
  signal DCD_n          : Std_Logic;
  signal RTS_n          : Std_Logic;
  signal CTS_n          : Std_Logic;
 
  -- keyboard port
  signal keyboard_data_out : std_logic_vector(7 downto 0);
  signal keyboard_cs       : std_logic;
  signal keyboard_irq      : std_logic;
 
  -- RAM
  signal ram_cs         : std_logic; -- memory chip select
  signal ram_data_out   : std_logic_vector(7 downto 0);
  signal ram_rd_req     : std_logic; -- ram read request        (asynch set on ram read, cleared falling CPU clock edge)
  signal ram_wr_req     : std_logic; -- ram write request (set on rising CPU clock edge, asynch clear on acknowledge) 
  signal ram_hold       : std_logic; -- hold off slow accesses
  signal ram_release    : std_logic; -- Release ram hold
 
  -- CPU Interface signals
  signal cpu_reset      : Std_Logic;
  signal cpu_clk        : Std_Logic;
  signal cpu_rw         : std_logic;
  signal cpu_vma        : std_logic;
  signal cpu_halt       : std_logic;
  signal cpu_hold       : std_logic;
  signal cpu_firq       : std_logic;
  signal cpu_irq        : std_logic;
  signal cpu_nmi        : std_logic;
  signal cpu_addr       : std_logic_vector(15 downto 0);
  signal cpu_data_in    : std_logic_vector(7 downto 0);
  signal cpu_data_out   : std_logic_vector(7 downto 0);
 
  -- Dynamic Address Translation
  signal dat_cs       : std_logic;
  signal dat_addr     : std_logic_vector(7 downto 0);
 
  -- Video Display Unit
  signal vdu_cs         : std_logic;
  signal vdu_data_out   : std_logic_vector(7 downto 0);
  signal vga_red_o      : std_logic;
  signal vga_green_o    : std_logic;
  signal vga_blue_o     : std_logic;
 
  -- timer
  signal timer_data_out : std_logic_vector(7 downto 0);
  signal timer_cs       : std_logic;
  signal timer_irq      : std_logic;
 
  -- trap
  signal trap_cs        : std_logic;
  signal trap_data_out  : std_logic_vector(7 downto 0);
  signal trap_irq       : std_logic;
 
  -- Peripheral Bus port
  signal pb_data_out   : std_logic_vector(7 downto 0);
  signal pb_cs         : std_logic;       -- peripheral bus chip select
  signal pb_wru        : std_logic;       -- upper byte write strobe
  signal pb_wrl        : std_logic;       -- lower byte write strobe
  signal pb_rdu        : std_logic;       -- upper byte read strobe
  signal pb_rdl        : std_logic;       -- lower byte read strobe
  signal pb_hold       : std_logic;       -- hold peripheral bus access
  signal pb_release    : std_logic;       -- release hold of peripheral bus
  signal pb_count      : std_logic_vector(3 downto 0); -- hold counter
  signal pb_hold_state : hold_state_type;
  signal pb_wreg       : std_logic_vector(7 downto 0); -- lower byte write register
  signal pb_rreg       : std_logic_vector(7 downto 0); -- lower byte read register
 
  -- Peripheral chip selects on Peripheral Bus
  signal ide_cs        : std_logic; -- IDE CF interface
  signal ether_cs      : std_logic;     -- Ethernet interface
  signal slot1_cs      : std_logic;     -- Expansion slot 1
  signal slot2_cs      : std_logic;     -- Expansion slot 2
 
  signal rst_i         : std_logic;     -- internal reset signal
--  signal clk_i         : std_logic;     -- internal master clock signal
  signal lock          : std_logic;     -- SDRAM clock DLL lock indicator
 
  -- signals that go through the SDRAM host-side interface
  signal opBegun       : std_logic;        -- SDRAM operation started indicator
  signal earlyBegun    : std_logic;        -- SDRAM operation started indicator
  signal ramDone       : std_logic;        -- SDRAM operation complete indicator
  signal rdDone        : std_logic;        -- SDRAM read operation complete indicator
  signal wrDone        : std_logic;        -- SDRAM write operation complete indicator
  signal hAddr         : std_logic_vector(HADDR_WIDTH-1 downto 0);  -- host address bus
  signal hDIn          : std_logic_vector(DATA_WIDTH-1 downto 0);  -- host-side data to SDRAM
  signal hDOut         : std_logic_vector(DATA_WIDTH-1 downto 0);  -- host-side data from SDRAM
  signal hRd           : std_logic;        -- host-side read control signal
  signal hWr           : std_logic;        -- host-side write control signal
  signal hUds          : std_logic;        -- host-side upper data strobe
  signal hLds          : std_logic;        -- host-side lower data strobe
  signal rdPending     : std_logic;        -- read operation pending in SDRAM pipeline
  type ram_type is (ram_state_0,
                    ram_state_rd1, ram_state_rd2,
                    ram_state_wr1,
                                                  ram_state_3 );
  signal ram_state     : ram_type;
 
 
--  signal BaudCount   : std_logic_vector(5 downto 0);
  signal CountL        : std_logic_vector(23 downto 0);
  signal clk_count     : natural range 0 to CPU_CLK_DIV;
  signal Clk25         : std_logic;
  signal vga_clk       : std_logic;
 
-----------------------------------------------------------------
--
-- CPU09 CPU core
--
-----------------------------------------------------------------
 
component cpu09
  port (
         clk:        in std_logic;
    rst:      in        std_logic;
    vma:             out        std_logic;
    addr:     out       std_logic_vector(15 downto 0);
    rw:      out        std_logic;              -- Asynchronous memory interface
         data_out: out std_logic_vector(7 downto 0);
    data_in:  in        std_logic_vector(7 downto 0);
         irq:      in  std_logic;
         firq:     in  std_logic;
         nmi:      in  std_logic;
         halt:     in  std_logic;
         hold:     in  std_logic
  );
end component;
 
 
----------------------------------------
--
-- 4K Block RAM Monitor ROM
--
----------------------------------------
component mon_rom
    Port (
       clk   : in  std_logic;
                 rst   : in  std_logic;
                 cs    : in  std_logic;
                 rw    : in  std_logic;
       addr  : in  std_logic_vector (11 downto 0);
       data_out : out std_logic_vector (7 downto 0);
       data_in : in  std_logic_vector (7 downto 0)
    );
end component;
 
 
----------------------------------------
--
-- 8KBytes Block RAM for FLEX9
-- $C000 - $DFFF
--
----------------------------------------
component flex_ram
  Port (
    clk      : in  std_logic;
    rst      : in  std_logic;
    cs       : in  std_logic;
    rw       : in  std_logic;
    addr     : in  std_logic_vector (12 downto 0);
    data_out    : out std_logic_vector (7 downto 0);
    data_in    : in  std_logic_vector (7 downto 0)
    );
end component;
 
-----------------------------------------------------------------
--
-- 6850 Compatible ACIA / UART
--
-----------------------------------------------------------------
 
component acia6850
  port (
     clk      : in  Std_Logic;  -- System Clock
     rst      : in  Std_Logic;  -- Reset input (active high)
     cs       : in  Std_Logic;  -- miniUART Chip Select
     rw       : in  Std_Logic;  -- Read / Not Write
     addr     : in  Std_Logic;  -- Register Select
     data_in  : in  Std_Logic_Vector(7 downto 0); -- Data Bus In 
     data_out : out Std_Logic_Vector(7 downto 0); -- Data Bus Out
     irq      : out Std_Logic;  -- Interrupt
     RxC      : in  Std_Logic;  -- Receive Baud Clock
     TxC      : in  Std_Logic;  -- Transmit Baud Clock
     RxD      : in  Std_Logic;  -- Receive Data
     TxD      : out Std_Logic;  -- Transmit Data
     DCD_n    : in  Std_Logic;  -- Data Carrier Detect
     CTS_n    : in  Std_Logic;  -- Clear To Send
     RTS_n    : out Std_Logic );  -- Request To send
end component;
 
 
-----------------------------------------------------------------
--
-- ACIA Clock divider
--
-----------------------------------------------------------------
 
component ACIA_Clock
  generic (
     SYS_CLK_FREQ  : integer :=  SYS_CLK_FREQ;
          ACIA_CLK_FREQ : integer := ACIA_CLK_FREQ
  );
  port (
     clk      : in  Std_Logic;  -- System Clock Input
          ACIA_clk : out Std_logic   -- ACIA Clock output
  );
end component;
 
 
----------------------------------------
--
-- PS/2 Keyboard
--
----------------------------------------
 
component keyboard
  generic(
  KBD_CLK_FREQ : integer := CPU_CLK_FREQ
  );
  port(
  clk             : in    std_logic;
  rst             : in    std_logic;
  cs              : in    std_logic;
  rw              : in    std_logic;
  addr            : in    std_logic;
  data_in         : in    std_logic_vector(7 downto 0);
  data_out        : out   std_logic_vector(7 downto 0);
  irq             : out   std_logic;
  kbd_clk         : inout std_logic;
  kbd_data        : inout std_logic
  );
end component;
 
----------------------------------------
--
-- Video Display Unit.
--
----------------------------------------
component vdu8
      generic(
        VDU_CLK_FREQ           : integer := CPU_CLK_FREQ; -- HZ
        VGA_CLK_FREQ           : integer := VGA_CLK_FREQ; -- HZ
             VGA_HOR_CHARS          : integer := 80; -- CHARACTERS
             VGA_VER_CHARS          : integer := 25; -- CHARACTERS
             VGA_PIX_PER_CHAR       : integer := 8;  -- PIXELS
             VGA_LIN_PER_CHAR       : integer := 16; -- LINES
             VGA_HOR_BACK_PORCH     : integer := 40; -- PIXELS
             VGA_HOR_SYNC           : integer := 96; -- PIXELS
             VGA_HOR_FRONT_PORCH    : integer := 24; -- PIXELS
             VGA_VER_BACK_PORCH     : integer := 13; -- LINES
             VGA_VER_SYNC           : integer := 2;  -- LINES
             VGA_VER_FRONT_PORCH    : integer := 35  -- LINES
      );
      port(
                -- control register interface
      vdu_clk      : in  std_logic;      -- CPU Clock - 25MHz
      vdu_rst      : in  std_logic;
                vdu_cs       : in  std_logic;
                vdu_rw       : in  std_logic;
                vdu_addr     : in  std_logic_vector(2 downto 0);
      vdu_data_in  : in  std_logic_vector(7 downto 0);
      vdu_data_out : out std_logic_vector(7 downto 0);
 
      -- vga port connections
                vga_clk      : in  std_logic;   -- VGA Pixel Clock - 25 MHz
      vga_red_o    : out std_logic;
      vga_green_o  : out std_logic;
      vga_blue_o   : out std_logic;
      vga_hsync_o  : out std_logic;
      vga_vsync_o  : out std_logic
   );
end component;
 
 
----------------------------------------
--
-- Timer module
--
----------------------------------------
 
component timer
  port (
     clk       : in std_logic;
     rst       : in std_logic;
     cs        : in std_logic;
     rw        : in std_logic;
     addr      : in std_logic;
     data_in   : in std_logic_vector(7 downto 0);
          data_out  : out std_logic_vector(7 downto 0);
          irq       : out std_logic
          );
end component;
 
------------------------------------------------------------
--
-- Bus Trap logic
--
------------------------------------------------------------
 
component trap
        port (
         clk        : in  std_logic;
    rst        : in  std_logic;
    cs         : in  std_logic;
    rw         : in  std_logic;
    vma        : in  std_logic;
    addr       : in  std_logic_vector(15 downto 0);
    data_in    : in  std_logic_vector(7 downto 0);
         data_out   : out std_logic_vector(7 downto 0);
         irq        : out std_logic
  );
end component;
 
 
----------------------------------------
--
-- Dynamic Address Translation Registers
--
----------------------------------------
component dat_ram
  port (
    clk      : in  std_logic;
         rst      : in  std_logic;
         cs       : in  std_logic;
         rw       : in  std_logic;
         addr_lo  : in  std_logic_vector(3 downto 0);
         addr_hi  : in  std_logic_vector(3 downto 0);
    data_in  : in  std_logic_vector(7 downto 0);
         data_out : out std_logic_vector(7 downto 0)
  );
end component;
 
 
 
--
-- Clock buffer
--
component BUFG
   Port (
     i: in std_logic;
          o: out std_logic
  );
end component;
 
begin
  -----------------------------------------------------------------------------
  -- Instantiation of internal components
  -----------------------------------------------------------------------------
 
my_cpu : cpu09  port map (
         clk         => cpu_clk,
    rst       => cpu_reset,
    vma       => cpu_vma,
    addr      => cpu_addr(15 downto 0),
    rw       => cpu_rw,
         data_out  => cpu_data_out,
    data_in   => cpu_data_in,
         irq       => cpu_irq,
         firq      => cpu_firq,
         nmi       => cpu_nmi,
         halt      => cpu_halt,
         hold      => cpu_hold
  );
 
my_rom : mon_rom port map (
       clk   => cpu_clk,
                 rst   => cpu_reset,
                 cs    => rom_cs,
                 rw    => '1',
       addr  => cpu_addr(11 downto 0),
       data_in => cpu_data_out,
       data_out => rom_data_out
    );
 
--my_flex : flex_ram port map (
--    clk       => cpu_clk,
--    rst       => cpu_reset,
--       cs        => flex_cs,
--       rw        => cpu_rw,
--    addr      => cpu_addr(12 downto 0),
--    data_out     => flex_data_out,
--    data_in     => cpu_data_out
--    );
 
my_acia  : acia6850 port map (
         clk         => cpu_clk,
         rst       => cpu_reset,
    cs        => acia_cs,
         rw        => cpu_rw,
    addr      => cpu_addr(0),
         data_in   => cpu_data_out,
         data_out  => acia_data_out,
    irq       => acia_irq,
         RxC       => acia_clk,
         TxC       => acia_clk,
         RxD       => rxd,
         TxD       => txd,
         DCD_n     => dcd_n,
         CTS_n     => cts_n,
         RTS_n     => rts_n
         );
 
 
my_ACIA_Clock : ACIA_Clock
  generic map(
    SYS_CLK_FREQ  =>  SYS_CLK_FREQ,
         ACIA_CLK_FREQ => ACIA_CLK_FREQ
  )
  port map(
    clk        => Clk_i,
    acia_clk   => acia_clk
  );
 
----------------------------------------
--
-- PS/2 Keyboard Interface
--
----------------------------------------
--my_keyboard : keyboard
--   generic map (
--      KBD_CLK_FREQ => CPU_CLK_FREQ
--      ) 
--   port map(
--      clk          => cpu_clk,
--      rst          => cpu_reset,
--      cs           => keyboard_cs,
--      rw           => cpu_rw,
--      addr         => cpu_addr(0),
--      data_in      => cpu_data_out(7 downto 0),
--      data_out     => keyboard_data_out(7 downto 0),
--      irq          => keyboard_irq,
--      kbd_clk      => ps2_clk,
--      kbd_data     => ps2_dat
--      );
 
----------------------------------------
--
-- Video Display Unit instantiation
--
----------------------------------------
--my_vdu : vdu8 
--  generic map(
--      VDU_CLK_FREQ           => CPU_CLK_FREQ, -- HZ
--      VGA_CLK_FREQ           => VGA_CLK_FREQ, -- HZ
--         VGA_HOR_CHARS          => 80, -- CHARACTERS
--         VGA_VER_CHARS          => 25, -- CHARACTERS
--         VGA_PIX_PER_CHAR       => 8,  -- PIXELS
--         VGA_LIN_PER_CHAR       => 16, -- LINES
--         VGA_HOR_BACK_PORCH     => 40, -- PIXELS
--         VGA_HOR_SYNC           => 96, -- PIXELS
--         VGA_HOR_FRONT_PORCH    => 24, -- PIXELS
--         VGA_VER_BACK_PORCH     => 13, -- LINES
--         VGA_VER_SYNC           => 2,  -- LINES
--         VGA_VER_FRONT_PORCH    => 35  -- LINES
--  )
--  port map(
--
--              -- Control Registers
--              vdu_clk       => cpu_clk,                                        -- 12.5 MHz System Clock in
--      vdu_rst       => cpu_reset,
--              vdu_cs        => vdu_cs,
--              vdu_rw        => cpu_rw,
--              vdu_addr      => cpu_addr(2 downto 0),
--              vdu_data_in   => cpu_data_out,
--              vdu_data_out  => vdu_data_out,
--
--      -- vga port connections
--      vga_clk       => vga_clk,                                        -- 25 MHz VDU pixel clock
--      vga_red_o     => vga_red_o,
--      vga_green_o   => vga_green_o,
--      vga_blue_o    => vga_blue_o,
--      vga_hsync_o   => vga_hsync_n,
--      vga_vsync_o   => vga_vsync_n
--   );
 
----------------------------------------
--
-- Timer Module
--
----------------------------------------
my_timer  : timer port map (
    clk       => cpu_clk,
         rst       => cpu_reset,
    cs        => timer_cs,
         rw        => cpu_rw,
    addr      => cpu_addr(0),
         data_in   => cpu_data_out,
         data_out  => timer_data_out,
    irq       => timer_irq
    );
 
----------------------------------------
--
-- Bus Trap Interrupt logic
--
----------------------------------------
my_trap : trap port map (
         clk        => cpu_clk,
    rst        => cpu_reset,
    cs         => trap_cs,
    rw         => cpu_rw,
         vma        => cpu_vma,
    addr       => cpu_addr,
    data_in    => cpu_data_out,
         data_out   => trap_data_out,
         irq        => trap_irq
    );
 
 
my_dat : dat_ram port map (
    clk       => cpu_clk,
         rst       => cpu_reset,
         cs        => dat_cs,
         rw        => cpu_rw,
         addr_hi   => cpu_addr(15 downto 12),
         addr_lo   => cpu_addr(3 downto 0),
    data_in   => cpu_data_out,
         data_out  => dat_addr(7 downto 0)
         );
 
cpu_clk_buffer : BUFG port map(
    i => Clk25,
         o => cpu_clk
    );
 
vga_clk_buffer : BUFG port map(
    i => Clk25,
         o => vga_clk
    );
 
----------------------------------------------------------------------
--
-- Process to decode memory map
--
----------------------------------------------------------------------
 
mem_decode: process( cpu_addr, cpu_rw, cpu_vma,
                                                        dat_addr,
                                              rom_data_out,
                                                        flex_data_out,
                                                   acia_data_out,
                                                        keyboard_data_out,
                                                        vdu_data_out,
                                                        pb_data_out,
                                                        timer_data_out,
                                                        trap_data_out,
                                                        ram_data_out
                                                        )
begin
      cpu_data_in <= (others=>'0');
      dat_cs      <= '0';
      rom_cs      <= '0';
      flex_cs     <= '0';
           acia_cs     <= '0';
           keyboard_cs <= '0';
           vdu_cs      <= '0';
           timer_cs    <= '0';
           trap_cs     <= '0';
           pb_cs       <= '0';
           ide_cs      <= '0';
           ether_cs    <= '0';
           slot1_cs    <= '0';
           slot2_cs    <= '0';
           ram_cs      <= '0';
      if cpu_addr( 15 downto 8 ) = "11111111" then
              cpu_data_in <= rom_data_out;
         dat_cs      <= cpu_vma;              -- write DAT
         rom_cs      <= cpu_vma;              -- read  ROM
           --
                -- Sys09Bug Monitor ROM $F000 - $FFFF
                --
           elsif dat_addr(3 downto 0) = "1111" then -- $XF000 - $XFFFF
                   cpu_data_in <= rom_data_out;
                        rom_cs      <= cpu_vma;
 
      --
                -- IO Devices $E000 - $E7FF
                --
                elsif dat_addr(3 downto 0) = "1110" then -- $XE000 - $XEFFF
                        case cpu_addr(11 downto 8) is
                        --
                        -- SWTPC peripherals from $E000 to $E0FF
                        --
                        when "0000" =>
                     case cpu_addr(7 downto 4) is
                          --
                          -- Console Port ACIA $E000 - $E00F
                          --
                          when "0000" => -- $E000
                       cpu_data_in <= acia_data_out;
                            acia_cs     <= cpu_vma;
 
           --
           -- Reserved
                          -- Floppy Disk Controller port $E010 - $E01F
                          --
 
           --
           -- Keyboard port $E020 - $E02F
                          --
                          when "0010" => -- $E020
             cpu_data_in <= keyboard_data_out;
                            keyboard_cs <= cpu_vma;
 
           --
           -- VDU port $E030 - $E03F
                          --
                          when "0011" => -- $E030
             cpu_data_in <= vdu_data_out;
                            vdu_cs      <= cpu_vma;
 
           --
                          -- Reserved SWTPc MP-T Timer $E040 - $E04F
                          --
                          when "0100" => -- $E040
             cpu_data_in <= (others=> '0');
 
           --
           -- Timer $E050 - $E05F
                          --
                          when "0101" => -- $E050
             cpu_data_in <= timer_data_out;
             timer_cs    <= cpu_vma;
 
           --
           -- Bus Trap Logic $E060 - $E06F
                          --
                          when "0110" => -- $E060
             cpu_data_in <= trap_data_out;
                            trap_cs     <= cpu_vma;
 
           --
                          -- Reserved SWTPc MP-ID PIA Timer/Printer Port $E080 - $E08F
                          --
 
           --
                          -- Reserved SWTPc MP-ID PTM 6840 Timer Port $E090 - $E09F
                          --
 
                          --
                          -- Remaining 6 slots reserved for non SWTPc Peripherals
                          --
                          when others => -- $E0A0 to $E0FF
                            null;
                     end case;
                        --
                        -- XST-3.0 Peripheral Bus goes here
                        --      $E100 to $E1FF
                        --      Four devices
                        -- IDE, Ethernet, Slot1, Slot2
                        --
                        when "0001" =>
                          cpu_data_in <= pb_data_out;
                          pb_cs       <= cpu_vma;
                     case cpu_addr(7 downto 6) is
                          --
                          -- IDE Interface $E100 to $E13F
                          --
                          when "00" =>
                            ide_cs   <= cpu_vma;
                          --
                          -- Ethernet Interface $E140 to $E17F
                          --
                          when "01" =>
                            ether_cs <= cpu_vma;
                          --
                          -- Slot 1 Interface $E180 to $E1BF
                          --
                          when "10" =>
                            slot1_cs <= cpu_vma;
                          --
                          -- Slot 2 Interface $E1C0 to $E1FF
                          --
                          when "11" =>
                            slot2_cs <= cpu_vma;
           --
                          -- Nothing else
                          --
           when others =>
                            null;
           end case;
         --
                        --      $E200 to $EFFF reserved for future use
                        --
                when others =>
                          null;
         end case;
                --
                -- Flex RAM $0C000 - $0DFFF
                --
                elsif dat_addr(7 downto 1) = "0000110" then -- $0C000 - $0DFFF
                   cpu_data_in <= flex_data_out;
                        flex_cs     <= cpu_vma;
                --
                -- Everything else is RAM
                --
                else
                   cpu_data_in <= ram_data_out;
                   ram_cs      <= cpu_vma;
          end if;
end process;
 
 
--
-- 16-bit Peripheral Bus
-- 6809 Big endian
-- ISA bus little endian
-- Not sure about IDE interface
--
peripheral_bus: process( clk_i, cpu_reset, cpu_rw, cpu_addr, cpu_data_out,
                         pb_cs, pb_wreg, pb_rreg )
begin
  pb_wru <= pb_cs and (not cpu_rw) and (not cpu_addr(0));
  pb_wrl <= pb_cs and (not cpu_rw) and      cpu_addr(0) ;
  pb_rdu <= pb_cs and      cpu_rw  and (not cpu_addr(0));
  pb_rdl <= pb_cs and      cpu_rw  and      cpu_addr(0) ;
  pb_a   <= cpu_addr(5 downto 1);
 
  --
  -- Register upper byte from CPU on first CPU write
  -- and lower byte from the peripheral bus on first CPU read
  --
  if cpu_reset = '1' then
    pb_wreg <= (others => '0');
    pb_rreg <= (others => '0');
  elsif clk_i'event and clk_i ='1' then
    if pb_wru = '1' then
           pb_wreg <= cpu_data_out;
    end if;
    if pb_rdu = '1' then
           pb_rreg <= pb_d(7 downto 0);
    end if;
   end if;
  --
  -- Peripheral bus read and write strobes are
  -- Syncronized with the 50 MHz clock
  -- and are asserted until the peripheral bus hold is released
  --
  if cpu_reset = '1' then
    pb_wr_n <= '1';
    pb_rd_n <= '1';
  elsif clk_i'event and clk_i ='1' then
         if pb_hold = '1' then
           pb_wr_n  <= not pb_wrl;
           pb_rd_n  <= not pb_rdu;
    else
      pb_wr_n <= '1';
      pb_rd_n <= '1';
    end if;
  end if;
  --
  -- The peripheral bus will be an output 
  -- the registered even byte on data(15 downto 8)
  -- and the CPU odd bytes on data(7 downto 0)
  -- on odd byte writes
  --
  if pb_wrl = '1' then
    pb_d <= pb_wreg & cpu_data_out;
  else
    pb_d <= (others => 'Z');
  end if;
 
  --
  -- On even byte reads,
  -- the CPU reads the low (even) byte of the peripheral bus
  -- On odd byte reads,
  -- the CPU reads the registered (odd byte) input from the peripheral bus
  --
  if pb_rdu = '1' then
    pb_data_out <= pb_d(15 downto 8);
  elsif pb_rdl = '1' then
    pb_data_out <= pb_rreg;
  else
    pb_data_out <= (others => '0');
  end if;
 
end process;
 
--
-- Hold Peripheral bus accesses for a few cycles
--
peripheral_bus_hold: process( cpu_clk, cpu_reset, pb_rdu, pb_wrl ) --, ether_rdy )
begin
    if cpu_reset = '1' then
                 pb_release    <= '0';
                 pb_count      <= "0000";
            pb_hold_state <= hold_release_state;
         elsif rising_edge(cpu_clk) then
  --
  -- The perpheral bus hold signal should be generated on 
  -- 16 bit bus read which will be on even byte reads or 
  -- 16 bit bus write which will be on odd byte writes.
  -- 
            case pb_hold_state is
                 when hold_release_state =>
          pb_release <= '0';
                    if (pb_rdu = '1') or (pb_wrl = '1') then
                            pb_count      <= "0100";
                                 pb_hold_state <= hold_request_state;
          elsif (pb_rdl = '1') or (pb_wru = '1') then
             pb_release    <= '1';
                                 pb_hold_state <= hold_release_state;
                         end if;
 
                 when hold_request_state =>
                         if pb_count = "0000" then
--            if ether_rdy = '1' then
              pb_release    <= '1';
                                  pb_hold_state <= hold_release_state;
--            end if;
          else
                       pb_count <= pb_count - "0001";
                         end if;
       when others =>
                    null;
       end case;
         end if;
end process;
 
--
-- Compact Flash Control
--
compact_flash: process( ide_cs, cpu_addr )
begin
         ide_cs0_n  <= not( ide_cs ) or cpu_addr(4);
         ide_cs1_n  <= not( ide_cs and cpu_addr(4));
         ide_dmack_n  <= '1';
end process;
 
--
-- Interrupts and other bus control signals
--
interrupts : process( SW3_N,
                                                         pb_cs, pb_hold, pb_release, ram_hold,
--                                                       ether_irq, 
                      acia_irq,
                                                         keyboard_irq,
                                                         trap_irq,
                                                         timer_irq
                                                         )
begin
    pb_hold    <= pb_cs and (not pb_release);
    cpu_irq    <= acia_irq or keyboard_irq;
         cpu_nmi    <= trap_irq or not( SW3_N );
         cpu_firq   <= timer_irq;
         cpu_halt   <= '0';
         cpu_hold   <= pb_hold or ram_hold;
    FLASH_CE_N <= '1';
end process;
 
 
--
-- Flash 7 segment LEDS
--
my_led_flasher: process( clk_i, rst_i, CountL )
begin
    if rst_i = '1' then
                   CountL <= "000000000000000000000000";
    elsif rising_edge(clk_i) then
                   CountL <= CountL + 1;
    end if;
--       S(7 downto 0) <= CountL(23 downto 16);
end process;
 
--
-- Generate CPU & Pixel Clock from Memory Clock
--
my_prescaler : process( clk_i, clk_count )
begin
  if rising_edge( clk_i ) then
 
    if clk_count = 0 then
           clk_count <= CPU_CLK_DIV-1;
         else
      clk_count <= clk_count - 1;
         end if;
 
    if clk_count = 0 then
            clk25 <= '0';
    elsif clk_count = (CPU_CLK_DIV/2) then
            clk25 <= '1';
    end if;
 
  end if;
end process;
 
--
-- Reset button and reset timer
--
my_switch_assignments : process( rst_i, SW2_N, lock )
begin
  rst_i <= not SW2_N;
  cpu_reset <= rst_i or (not lock);
end process;
 
--
-- RS232 signals:
--
my_acia_assignments : process( RS232_RXD, RS232_CTS, txd, rts_n )
begin
  rxd       <= RS232_RXD;
  cts_n     <= RS232_CTS;
  dcd_n     <= '0';
  RS232_TXD <= txd;
  RS232_RTS <= rts_n;
end process;
 
--
-- Pin assignments for ethernet controller
--
my_ethernet_assignments : process( clk_i, cpu_reset, ether_cs )
begin
    ether_cs_n  <= not ether_cs;
    ether_aen   <= not ether_cs; -- Ethernet address enable not 
    ether_bhe_n <= '1';          -- Ethernet bus high enable - 8 bit access only
end process;
 
--
-- I/O expansion slot assignments
--
my_slot_assignments : process( slot1_cs, slot2_cs)
begin
    slot1_cs_n <= not slot1_cs;
    slot2_cs_n <= not slot2_cs;
end process;
 
--
-- VGA ouputs
--
my_vga_assignments : process( vga_red_o, vga_green_o, vga_blue_o )
begin
  VGA_red(0)   <= vga_red_o;
  VGA_red(1)   <= vga_red_o;
  VGA_red(2)   <= vga_red_o;
  VGA_green(0) <= vga_green_o;
  VGA_green(1) <= vga_green_o;
  VGA_green(2) <= vga_green_o;
  VGA_blue(0)  <= vga_blue_o;
  VGA_blue(1)  <= vga_blue_o;
  VGA_blue(2)  <= vga_blue_o;
end process;
 
--
-- SDRAM read write control
--
my_sdram_rw : process( clk_i, cpu_reset,
                       opBegun, ramDone,
                                                          ram_state,
                       ram_rd_req, ram_wr_req )
begin
  if( cpu_reset = '1' ) then
         hRd        <= '0';
    hWr        <= '0';
         ram_hold   <= '0';
         ram_state  <= ram_state_0;
 
  elsif( falling_edge(clk_i) ) then
    --
         -- ram state machine
         --
    case ram_state is
 
    when ram_state_0 =>
                if ram_rd_req = '1' then
        ram_hold   <= '1';
             hRd        <= '1';
                  ram_state  <= ram_state_rd1;
      elsif ram_wr_req = '1' then
             ram_hold   <= '1';
        hWr        <= '1';
             ram_state  <= ram_state_wr1;
      end if;
 
    when ram_state_rd1 =>
           if opBegun = '1' then
                  hRd        <= '0';
                  ram_state  <= ram_state_rd2;
      end if;
 
    when ram_state_rd2 =>
           if ramDone = '1' then
                  ram_hold   <= '0';
                  ram_state  <= ram_state_3;
                end if;
 
    when ram_state_wr1 =>
           if opBegun = '1' then
                  ram_hold   <= '0';
                  hWr        <= '0';
                  ram_state  <= ram_state_3;
      end if;
 
    when ram_state_3 =>
           if ram_release = '1' then
                  ram_state  <= ram_state_0;
      end if;
 
         when others =>
                hRd        <= '0';
                hWr        <= '0';
                ram_hold   <= '0';
                ram_state  <= ram_state_0;
         end case;
 
  end if;
end process;
 
--
-- SDRAM Address and data bus assignments
--
my_sdram_addr_data : process( cpu_addr, dat_addr,
                                cpu_data_out, hDout )
begin
  hAddr(23 downto 19)  <= "00000";
  hAddr(18 downto 11)  <= dat_addr;
  hAddr(10 downto 0)   <= cpu_addr(11 downto 1);
  hUds                 <= not cpu_addr(0);
  hLds                 <=     cpu_addr(0);
  if cpu_addr(0) = '0' then
     hDin( 7 downto 0) <= (others=>'0');
     hDin(15 downto 8) <= cpu_data_out;
     ram_data_out      <= hDout(15 downto 8);
  else
     hDin( 7 downto 0) <= cpu_data_out;
     hDin(15 downto 8) <= (others=>'0');
     ram_data_out      <= hDout( 7 downto 0);
  end if;
end process;
 
--
-- Hold RAM until falling CPU clock edge
--
ram_bus_hold: process( cpu_clk, cpu_reset, ram_hold )
begin
    if ram_hold = '1' then
                 ram_release   <= '0';
         elsif falling_edge(cpu_clk) then
                 ram_release   <= '1';
         end if;
end process;
 
--
-- CPU read data request on rising CPU clock edge
--
ram_read_request: process( hRd, cpu_clk, ram_cs, cpu_rw, ram_release )
begin
         if hRd = '1' then
                ram_rd_req   <= '0';
         elsif rising_edge(cpu_clk) then
           if (ram_cs = '1') and (cpu_rw = '1') and (ram_release = '1') then
                  ram_rd_req   <= '1';
      end if;
         end if;
end process;
 
--
-- CPU write data to RAM valid on rising CPU clock edge
--
ram_write_request: process( hWr, cpu_clk, ram_cs, cpu_rw, ram_release )
begin
    if hWr = '1' then
                 ram_wr_req   <= '0';
         elsif rising_edge(cpu_clk) then
                if (ram_cs = '1') and (cpu_rw = '0') and (ram_release = '1') then
                  ram_wr_req   <= '1';
      end if;
         end if;
end process;
 
 
 
status_leds : process( rst_i, cpu_reset, lock )
begin
    S(0) <= rst_i;
         S(1) <= cpu_reset;
         S(2) <= lock;
         S(3)   <= countL(23);
         S(7 downto 4) <= "0000";
end process;
 
--debug_proc : process( cpu_reset, cpu_clk, cpu_rw, cpu_vma,
--                      cpu_halt, cpu_hold,
--                      cpu_firq, cpu_irq, cpu_nmi,
--                      cpu_addr, cpu_data_out, cpu_data_in )
--begin
--  cpu_reset_o    <= cpu_reset;
--  cpu_clk_o      <= cpu_clk;
--  cpu_rw_o       <= cpu_rw;
--  cpu_vma_o      <= cpu_vma;
--  cpu_halt_o     <= cpu_halt;
--  cpu_hold_o     <= cpu_hold;
--  cpu_firq_o     <= cpu_firq;
--  cpu_irq_o      <= cpu_irq;
--  cpu_nmi_o      <= cpu_nmi;
--  cpu_addr_o     <= cpu_addr;
--  cpu_data_out_o <= cpu_data_out;
--  cpu_data_in_o  <= cpu_data_in;
--end process;
 
 
end rtl; --===================== End of architecture =======================--
 
Browse

Tools

Subversion Repositories System09

[/] [System09/] [trunk/] [rtl/] [System09_Xilinx_ML506/] [System09_Xilinx_ML506.vhd] - Blame information for rev 141

Line No.	Rev	Author	Line
1	121	davidgb	`--===========================================================================----`
2			`--`
3			`-- S Y N T H E Z I A B L E System09 - SOC.`
4			`--`
5			`-- www.OpenCores.Org - February 2007`
6			`-- This core adheres to the GNU public license`
7			`--`
8			`-- File name : System09_Xilinx_ML506.vhd`
9			`--`
10			`-- Purpose : Top level file for 6809 compatible system on a chip`
11			`-- Designed with Xilinx Virtex-5.`
12			`-- Implemented With Xilinx ML506 FPGA board.`
13			`-- * Note *`
14			`-- This configuration can run Flex9 however it only has`
15			`-- 32k bytes of user memory and the VDU is monochrome`
16			`-- This configuration also lacks a DAT so cannot use`
17			`-- the RAM Disk features of SYS09BUG.`
18			`--`
19			`-- Dependencies : ieee.Std_Logic_1164`
20			`-- ieee.std_logic_unsigned`
21			`-- ieee.std_logic_arith`
22			`-- ieee.numeric_std`
23			`-- unisim.vcomponents`
24			`--`
25			`-- Uses : mon_rom (sys09bug_rom4k_b16.vhd) Sys09Bug Monitor ROM`
26			`-- cpu09 (cpu09.vhd) CPU core`
27			`-- ACIA_6850 (acia6850.vhd) ACIA / UART`
28			`-- ACIA_Clock (ACIA_Clock.vhd) ACIA clock.`
29			`-- keyboard (keyboard.vhd) PS/2 Keyboard interface`
30			`-- (ps2_keyboard.vhd)`
31			`-- (keymap_rom_slice.vhd) Key map table`
32			`-- vdu8_mono (vdu8_mono.vhd) Monochrome VDU`
33			`-- (char_rom2k_b16.vhd)`
34			`-- (ram2k_b16.vhd)`
35			`-- timer (timer.vhd) Interrupt timer`
36			`-- trap (trap.vhd) Bus condition trap logic`
37			`-- flex_ram (flex9_ram8k_b16.vhd) Flex operating system`
38			`-- ram_32K (ram32k_b16.vhd) 32 KBytes of Block RAM`
39			`--`
40			`--`