URL
https://opencores.org/ocsvn/amber/amber/trunk
[/] [amber/] [trunk/] [hw/] [fpga/] [flash/] [README.txt] - Blame information for rev 85
Go to most recent revision |
Details |
Compare with Previous |
View Log
Line No. |
Rev |
Author |
Line |
1 |
79 |
csantifort |
|
2 |
|
|
Xilinx Flash/PROM - Write bitfile to SPI serial flash
|
3 |
|
|
The included file boot-loader-ethmac.mcs is a flash configuration file
|
4 |
|
|
for the SPI (serial) flash on the SP605 FPGA development board.
|
5 |
|
|
It contains the boot-loader-ethmac design. Here are instructions on how to create an mcs file
|
6 |
|
|
and how to load it onto the SP605 board. These instructions are for Xilinx ISE 14.5.
|
7 |
|
|
|
8 |
|
|
|
9 |
|
|
1. Start impact. Select Prepare a PROM file
|
10 |
|
|
Step 1. Select Storage Target
|
11 |
|
|
SPI Flash -> Configure single FPGA
|
12 |
|
|
|
13 |
|
|
Step 2. Add Storage Device
|
14 |
|
|
64M
|
15 |
|
|
|
16 |
|
|
Step 3
|
17 |
|
|
File Format MCS
|
18 |
|
|
Add Non_Configuration Files No
|
19 |
|
|
|
20 |
|
|
Select the bitfile to write
|
21 |
|
|
Would you like to add another device file to Revision:0 ? No
|
22 |
|
|
|
23 |
|
|
Impact Process->Generate File...
|
24 |
|
|
Impact creates an MCS file and says Generate Succeeded.
|
25 |
|
|
|
26 |
|
|
Then restart impact and select Boundary Scan flow
|
27 |
|
|
Right mouse on the FPGA and select Add SPI/BPI Flash
|
28 |
|
|
|
29 |
|
|
Select Attached SPI/BPI dialogue
|
30 |
|
|
SPI PROM -> W25Q64FV
|
31 |
|
|
Data Width: 1
|
32 |
|
|
|
33 |
|
|
Then a Flash device appears in the Boundary scan window attached the tje xc6slx45t FPGA.
|
34 |
|
|
Right mouse on the Flash and select Program
|
35 |
|
|
This takes a couple of minutes.
|
36 |
|
|
|
37 |
|
|
To use that image, you need the following switch settings on the SP605 board;
|
38 |
|
|
SW1 (the 2-switch block box near the red on/off power switch in the upper right corner of the board)
|
39 |
|
|
M0=on, M1=off
|
40 |
|
|
Then press the PROG button just below it to load that bitfile from the SPI flash into the FPGA.
|
41 |
|
|
|
42 |
80 |
csantifort |
To use the Parallel flash
|
43 |
|
|
M0=off, M1=off
|
44 |
79 |
csantifort |
|
45 |
80 |
csantifort |
|
46 |
79 |
csantifort |
Online tutorial for instructions with pictures -
|
47 |
|
|
http://www.digilentinc.com/Data/Documents/Tutorials/MCS%20File%20Creation%20with%20Xilinx%20ISE%20Tutorial.pdf
|
© copyright 1999-2024
OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.