URL https://opencores.org/ocsvn/cpu_lecture/cpu_lecture/trunk

Subversion Repositories cpu_lecture

[/] [cpu_lecture/] [trunk/] [html/] [08_IO.html] - Blame information for rev 11

Go to most recent revision | Details | Compare with Previous | View Log


<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN"
"http://www.w3.org/TR/html4/strict.dtd">
<HTML>
<HEAD>
<TITLE>html/IO</TITLE>
<META NAME="generator" CONTENT="HTML::TextToHTML v2.46">
<LINK REL="stylesheet" TYPE="text/css" HREF="lecture.css">
</HEAD>
<BODY>
<P><table class="ttop"><th class="tpre"><a href="07_Opcode_Decoder.html">Previous Lesson</a></th><th class="ttop"><a href="toc.html">Table of Content</a></th><th class="tnxt"><a href="09_Toolchain_Setup.html">Next Lesson</a></th></table>
<hr>
 
<H1><A NAME="section_1">8 INPUT/OUTPUT</A></H1>
 
<P>The last piece in the design is the input/output unit. Strictly speaking
it does not belong to the CPU as such, but we discuss it briefly to
see how it connects to the CPU.
 
<H2><A NAME="section_1_1">8.1 Interface to the CPU</A></H2>
 
<P>As we have already seen in the top level design, the I/O unit uses the same
clock as the CPU (which greatly simplifies its design).
 
<P>The interface towards the CPU consist of the following signals:
 
<TABLE>
<TR><TD>ADR_IO</TD><TD>The number of an individual I/O register
</TD></TR><TR><TD>DIN</TD><TD>Data to an I/O register (I/O write)
</TD></TR><TR><TD>RD_IO</TD><TD>Read Strobe
</TD></TR><TR><TD>WR_IO</TD><TD>Write Strobe
</TD></TR><TR><TD>DOUT</TD><TD>Data from an I/O register (I/O read cycle.
</TD></TR>
</TABLE>
<P>These signals are well known from other I/O devices like UARTs,
Ethernet Controllers, and the like.
 
<P>The CPU supports two kinds of accesses to I/O registers: I/O reads
(with the IN or LDS instructions, but also for the skip instructions
SBIC and SBIS), and I/O writes (with the OUT or STS instructions,
but also with the bit instructions CBI and SBI).
 
<P>The skip instructions SBIC and SBIS execute in 2 cycles; in the first
cycle an I/O read is performed while the skip (or not) decision is made
in the second cycle. The reason for this is that the combinational delay
for a single cycle would have been too long.
 
<P>From the I/O unit's perspective, I/O reads and writes are performed
in a single cycle (even if the CPU needs another cycle to complete an
instruction.
 
<P>The I/O unit generates an interrupt vector on its <STRONG>INTVEC</STRONG> output.
The upper bit of the <STRONG>INTVEC</STRONG> output is set if an interrupt is pending.
 
<H2><A NAME="section_1_2">8.2 CLR Signal</A></H2>
 
<P>Some I/O components need a <STRONG>CLR</STRONG> signal to bring them into a defined state.
The <STRONG>CLR</STRONG> signal of the CPU is used for this purpose.
 
<H2><A NAME="section_1_3">8.3 Connection the FPGA Pins</A></H2>
 
<P>The remaining signals into and out of the I/O unit are more or less
directly connected to FPGA pins.
 
<P>The <STRONG>RX</STRONG> input comes from an RS232 receiver/driver chip and is the serial
input for an UART (active low). The TX output (also active low) is the
serial output from that UART and goes back to the RS232 receiver/driver chip:
 
<P><br>
 
<pre class="vhdl">
 
 89                     I_RX       => I_RX,
 90
 91                     Q_TX       => Q_TX,
<pre class="filename">
src/io.vhd
</pre></pre>
<P>
 
<P>The <STRONG>SWITCH</STRONG> input comes from a DIP switch on the board.
The values of the switch can be read from I/O register <STRONG>PINB</STRONG> (0x36).
 
<P><br>
 
<pre class="vhdl">
 
132                 when X"36"  => Q_DOUT <= I_SWITCH;  -- PINB
<pre class="filename">
src/io.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>The 7_<STRONG>SEGMENT</STRONG> output drives the 7 segments of a 7-segment display.
This output can be set from software by writing to the <STRONG>PORTB</STRONG> (0x38)
I/O register. The segments can also be driven by a debug function which
shows the current <STRONG>PC</STRONG> and the current opcode of the CPU.
 
<P><br>
 
<pre class="vhdl">
 
147                         when X"38"  => Q_7_SEGMENT <= I_DIN(6 downto 0);    -- PORTB
<pre class="filename">
src/io.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>The choice between the debug display and the software controlled
display function is made by the DIP switch setting:
 
<P><br>
 
<pre class="vhdl">
 
183
<pre class="filename">
src/avr_fpga.vhd
</pre></pre>
<P>
 
<P><br>
 
<H2><A NAME="section_1_4">8.4 I/O Read</A></H2>
 
<P>I/O read cycles are indicated by the <STRONG>RD_IO</STRONG> signal. If <STRONG>RD_IO</STRONG> is applied,
then the address of the I/O register to be read is provided on the <STRONG>ADR_IO</STRONG>
input and the value of that register is expected on <STRONG>DOUT</STRONG> at the next
<STRONG>CLK</STRONG> edge.
 
<P>This is accomplished by the I/O read process:
 
<P><br>
 
<pre class="vhdl">
 
 98         iord: process(I_ADR_IO, I_SWITCH,
 99                       U_RX_DATA, U_RX_READY, L_RX_INT_ENABLED,
100                       U_TX_BUSY, L_TX_INT_ENABLED)
101         begin
102             -- addresses for mega8 device (use iom8.h or #define __AVR_ATmega8__).
103             --
104             case I_ADR_IO is
105                 when X"2A"  => Q_DOUT <=             -- UCSRB:
106                                    L_RX_INT_ENABLED  -- Rx complete int enabled.
107                                  & L_TX_INT_ENABLED  -- Tx complete int enabled.
108                                  & L_TX_INT_ENABLED  -- Tx empty int enabled.
109                                  & '1'               -- Rx enabled
110                                  & '1'               -- Tx enabled
111                                  & '0'               -- 8 bits/char
112                                  & '0'               -- Rx bit 8
113                                  & '0';              -- Tx bit 8
114                 when X"2B"  => Q_DOUT <=             -- UCSRA:
115                                    U_RX_READY       -- Rx complete
116                                  & not U_TX_BUSY    -- Tx complete
117                                  & not U_TX_BUSY    -- Tx ready
118                                  & '0'              -- frame error
119                                  & '0'              -- data overrun
120                                  & '0'              -- parity error
121                                  & '0'              -- double dpeed
122                                  & '0';             -- multiproc mode
123                 when X"2C"  => Q_DOUT <= U_RX_DATA; -- UDR
124                 when X"40"  => Q_DOUT <=            -- UCSRC
125                                    '1'              -- URSEL
126                                  & '0'              -- asynchronous
127                                  & "00"             -- no parity
128                                  & '1'              -- two stop bits
129                                  & "11"             -- 8 bits/char
130                                  & '0';             -- rising clock edge
131
132                 when X"36"  => Q_DOUT <= I_SWITCH;  -- PINB
133                 when others => Q_DOUT <= X"AA";
134             end case;
135         end process;
<pre class="filename">
src/io.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>I/O registers that are not implemented (i.e almost all) set <STRONG>DOUT</STRONG>
to 0xAA as a debugging aid.
 
<P>The outputs of sub-components (like the UART) are selected in the I/O read
process.
 
<H2><A NAME="section_1_5">8.5 I/O Write</A></H2>
 
<P>I/O write cycles are indicated by the <STRONG>WR_IO</STRONG> signal. If <STRONG>WR_IO</STRONG> is applied,
then the address of the I/O register to be written is provided on the <STRONG>ADR_IO</STRONG>
input and the value to be written is supplied on the DIN input:
 
<P><br>
 
<pre class="vhdl">
 
139         iowr: process(I_CLK)
140         begin
141             if (rising_edge(I_CLK)) then
142                 if (I_CLR = '1') then
143                     L_RX_INT_ENABLED  <= '0';
144                     L_TX_INT_ENABLED  <= '0';
145                 elsif (I_WE_IO = '1') then
146                     case I_ADR_IO is
147                         when X"38"  => Q_7_SEGMENT <= I_DIN(6 downto 0);    -- PORTB
148                                        L_LEDS <= not L_LEDS;
149                         when X"40"  =>  -- handled by uart
150                         when X"41"  =>  -- handled by uart
151                         when X"43"  => L_RX_INT_ENABLED <= I_DIN(0);
152                                        L_TX_INT_ENABLED <= I_DIN(1);
153                         when others =>
154                     end case;
155                 end if;
156             end if;
157         end process;
<pre class="filename">
src/io.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>In the I/O read process the outputs of sub-component were multiplexed
into the final output <STRONG>DOUT</STRONG> and hence their register numbers (like 0x2C
for the <STRONG>UDR</STRONG> read register) were visible, In the I/O write process, however,
the inputs of sub-components (again like 0x2C for the <STRONG>UDR</STRONG> write register)
are not visible in the write process and decoding of the <STRONG>WR</STRONG> (and <STRONG>RD</STRONG> where
needed)  strobes for sub components is done outside of these processes:
 
<P><br>
 
<pre class="vhdl">
 
182         L_WE_UART <= I_WE_IO when (I_ADR_IO = X"2C") else '0'; -- write UART UDR
183         L_RD_UART <= I_RD_IO when (I_ADR_IO = X"2C") else '0'; -- read  UART UDR
184
<pre class="filename">
src/io.vhd
</pre></pre>
<P>
 
<P><br>
 
<H2><A NAME="section_1_6">8.6 Interrupts</A></H2>
 
<P>Some I/O components raise interrupts, which are coordinated in the
I/O interrupt process:
 
<P><br>
 
<pre class="vhdl">
 
161         ioint: process(I_CLK)
162         begin
163             if (rising_edge(I_CLK)) then
164                 if (I_CLR = '1') then
165                     L_INTVEC <= "000000";
166                 else
167                     if (L_RX_INT_ENABLED and U_RX_READY) = '1' then
168                         if (L_INTVEC(5) = '0') then     -- no interrupt pending
169                             L_INTVEC <= "101011";       -- _VECTOR(11)
170                         end if;
171                     elsif (L_TX_INT_ENABLED and not U_TX_BUSY) = '1' then
172                         if (L_INTVEC(5) = '0') then     -- no interrupt pending
173                             L_INTVEC <= "101100";       -- _VECTOR(12)
174                         end if;
175                     else                                -- no interrupt
176                         L_INTVEC <= "000000";
177                     end if;
178                 end if;
179             end if;
180         end process;
<pre class="filename">
src/io.vhd
</pre></pre>
<P>
 
<P><br>
 
<H2><A NAME="section_1_7">8.7 The UART</A></H2>
 
<P>The UART is an important facility for debugging programs that are more
complex than out <STRONG>hello.c</STRONG>. We use a fixed baud rate of 38400 Baud
and a fixed data format of 8 data bits and 2 stop bits.
Therefore the corresponding bits in the UART control registers of the
original AVR CPU are not implemented. The fixed values are properly
reported, however.
 
<P>The UART consists of 3 independent sub-components: a baud rate generator,
a receiver, and a transmitter.
 
<H3><A NAME="section_1_7_1">8.7.1 The UART Baud Rate Generator</A></H3>
 
<P>The baud rate generator is clocked with a frequency of <STRONG>clock_freq</STRONG>
and is supposed to generate a x1 clock of <STRONG>baud_rate</STRONG> for the transmitter
and a x16 clock of 16*<STRONG>baud_rate</STRONG> for the receiver.
 
<P>The x16 clock is generated like this:
 
<P><br>
 
<pre class="vhdl">
 
 54
 55         baud16: process(I_CLK)
 56         begin
 57             if (rising_edge(I_CLK)) then
 58                 if (I_CLR = '1') then
 59                     L_COUNTER <= X"00000000";
 60                 elsif (L_COUNTER >= LIMIT) then
 61                     L_COUNTER <= L_COUNTER - LIMIT;
 62                 else
 63                     L_COUNTER <= L_COUNTER + BAUD_16;
 64                 end if;
 65             end if;
 66         end process;
 67
 68         baud1: process(I_CLK)
<pre class="filename">
src/baudgen.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>We have done a little trick here. Most baud rate generators divide the
input clock by a fixed integer number (like the one shown below for the
x1 clock). That is fine if the input clock is a multiple of the output
clock. More often than not is the CPU clock not a multiple of the the
baud rate. Therefore, if an integer divider is used (like in the original
AVR CPU, where the integer divisor was written into the UBRR I/O register)
then the error in the baud rate cumulates over all bits transmitted. This can
cause transmission errors when many characters are sent back to back.
An integer divider would have set <STRONG>L_COUNTER</STRONG> to 0 after reaching <STRONG>LIMIT</STRONG>,
which would have cause an absolute error of <STRONG>COUNTER</STRONG> - <STRONG>LIMIT</STRONG>. What we
do instead is to subtract <STRONG>LIMIT</STRONG>, which does no discard the error but
makes the next cycle a little shorter instead.
 
<P>Instead of using a fixed baud rate interval of N times the clock interval
(as fixed integer dividers would), we have used a variable baud rate interval;
the length of the interval varies slightly over time, but the total error
remains bounded. The error does not cumulate as for fixed integer
dividers.
 
<P>If you want to make the baud rate programmable, then you can replace the
generic <STRONG>baud_rate</STRONG> by a signal (and the trick would still work).
 
<P>The x1 clock is generated by dividing the x16 clock by 16:
 
<P><br>
 
<pre class="vhdl">
 
 70             if (rising_edge(I_CLK)) then
 71                 if (I_CLR = '1') then
 72                     L_CNT_16 <= "0000";
 73                 elsif (L_CE_16 = '1') then
 74                     L_CNT_16 <= L_CNT_16 + "0001";
 75                 end if;
 76             end if;
 77         end process;
 78
 79         L_CE_16 <= '1' when (L_COUNTER >= LIMIT) else '0';
 80         Q_CE_16 <= L_CE_16;
 81         Q_CE_1 <= L_CE_16 when L_CNT_16 = "1111" else '0';
<pre class="filename">
src/baudgen.vhd
</pre></pre>
<P>
 
<P><br>
 
<H3><A NAME="section_1_7_2">8.7.2 The UART Transmitter</A></H3>
 
<P>The UART transmitter is a shift register that is loaded with
the character to be transmitted (prepended with a start bit):
 
<P><br>
 
<pre class="vhdl">
 
 67                     elsif (L_FLAG /= I_FLAG) then       -- new byte
 68                         Q_TX <= '0';                    -- start bit
 69                         L_BUF <= I_DATA;                -- data bits
 70                         L_TODO <= "1001";
 71                     end if;
<pre class="filename">
src/uart_tx.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>The <STRONG>TODO</STRONG> signal holds the number of bits that remain to be shifted out.
The transmitter is clocked with the x1 baud rate:
 
<P><br>
 
<pre class="vhdl">
 
 59                 elsif (I_CE_1 = '1') then
 60                     if (L_TODO /= "0000") then          -- transmitting
 61                         Q_TX <= L_BUF(0);               -- next bit
 62                         L_BUF     <= '1' & L_BUF(7 downto 1);
 63                         if (L_TODO = "0001") then
 64                             L_FLAG <= I_FLAG;
 65                         end if;
 66                         L_TODO <= L_TODO - "0001";
 67                     elsif (L_FLAG /= I_FLAG) then       -- new byte
 68                         Q_TX <= '0';                    -- start bit
 69                         L_BUF <= I_DATA;                -- data bits
 70                         L_TODO <= "1001";
 71                     end if;
 72                 end if;
<pre class="filename">
src/uart_tx.vhd
</pre></pre>
<P>
 
<P><br>
 
<H3><A NAME="section_1_7_3">8.7.3 The UART Receiver</A></H3>
 
<P>The UART transmitter runs synchronously with the CPU clock; but the UART
receiver does not. We therefore clock the receiver input twice
in order to synchronize it with the CPU clock:
 
<P><br>
 
<pre class="vhdl">
 
 56         process(I_CLK)
 57         begin
 58             if (rising_edge(I_CLK)) then
 59                 if (I_CLR = '1') then
 60                     L_SERIN <= '1';
 61                     L_SER_HOT <= '1';
 62                 else
 63                     L_SERIN   <= I_RX;
 64                     L_SER_HOT <= L_SERIN;
 65                 end if;
 66             end if;
 67         end process;
<pre class="filename">
src/uart_rx.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>The key signal in the UART receiver is <STRONG>POSITION</STRONG> which is the current
position within the received character in units if 1/16 bit time. When the
receiver is idle and a start bit is received, then <STRONG>POSITION</STRONG> is reset to
1:
 
<P><br>
 
<pre class="vhdl">
 
 86                     if (L_POSITION = X"00") then            -- uart idle
 87                         L_BUF  <= "1111111111";
 88                         if (L_SER_HOT = '0')  then          -- start bit received
 89                             L_POSITION <= X"01";
 90                         end if;
<pre class="filename">
src/uart_rx.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>At every subsequent edge of the 16x baud rate, <STRONG>POSITION</STRONG> is incremented
and the receiver input (<STRONG>SER_HOT</STRONG>) input is checked at the middle of each
bit (i.e. when <STRONG>POSITION[3:0]</STRONG> = "0111").
If the start bit has disappeared at the middle of the bit, then this is
considered noise on the line rather than a valid start bit:
 
<P><br>
 
<pre class="vhdl">
 
 93                         if (L_POSITION(3 downto 0) = "0111") then       -- 1/2 bit
 94                             L_BUF <= L_SER_HOT & L_BUF(9 downto 1);     -- sample data
 95                             --
 96                             -- validate start bit
 97                             --
 98                             if (START_BIT and L_SER_HOT = '1') then     -- 1/2 start bit
 99                                 L_POSITION <= X"00";
100                             end if;
101
102                             if (STOP_BIT) then                          -- 1/2 stop bit
103                                 Q_DATA <= L_BUF(9 downto 2);
104                             end if;
<pre class="filename">
src/uart_rx.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>Reception of a byte already finishes at 3/4 of the stop bit. This is to
allow for cumulated baud rate errors of 1/4 bit time (or about 2.5 %
baud rate error for 10 bit (1 start, 8 data, and 1 stop bit) transmissions).
The received data is stored in <STRONG>DATA</STRONG>:
 
<P><br>
 
<pre class="vhdl">
 
105                         elsif (STOP_POS) then                       -- 3/4 stop bit
106                             L_FLAG <= L_FLAG xor (L_BUF(9) and not L_BUF(0));
107                             L_POSITION <= X"00";
<pre class="filename">
src/uart_rx.vhd
</pre></pre>
<P>
 
<P><br>
 
<P>If a greater tolerance against baud rate errors is needed, then one can
decrease <STRONG>STOP_POS</STRONG> a little, but generally it would be safer to use 2
stop bits on the sender side.
 
<P>This finalizes the description of the FPGA. We will proceed with the
design flow in the next lesson.
 
<P><hr><BR>
<table class="ttop"><th class="tpre"><a href="07_Opcode_Decoder.html">Previous Lesson</a></th><th class="ttop"><a href="toc.html">Table of Content</a></th><th class="tnxt"><a href="09_Toolchain_Setup.html">Next Lesson</a></th></table>
</BODY>
</HTML>

Browse

Tools

Subversion Repositories cpu_lecture

[/] [cpu_lecture/] [trunk/] [html/] [08_IO.html] - Blame information for rev 11

Line No.	Rev	Author	Line
1	2	jsauermann	`<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN"`
2			`"http://www.w3.org/TR/html4/strict.dtd">`
3			`<HTML>`
4			`<HEAD>`
5			`<TITLE>html/IO</TITLE>`
6			`<META NAME="generator" CONTENT="HTML::TextToHTML v2.46">`
7			`<LINK REL="stylesheet" TYPE="text/css" HREF="lecture.css">`
8			`</HEAD>`
9			`<BODY>`
10			`<P><table class="ttop"><th class="tpre"><a href="07_Opcode_Decoder.html">Previous Lesson</a></th><th class="ttop"><a href="toc.html">Table of Content</a></th><th class="tnxt"><a href="09_Toolchain_Setup.html">Next Lesson</a></th></table>`
11			`<hr>`
12
13			`<H1><A NAME="section_1">8 INPUT/OUTPUT</A></H1>`
14
15			`<P>The last piece in the design is the input/output unit. Strictly speaking`
16			`it does not belong to the CPU as such, but we discuss it briefly to`
17			`see how it connects to the CPU.`
18
19			`<H2><A NAME="section_1_1">8.1 Interface to the CPU</A></H2>`
20
21			`<P>As we have already seen in the top level design, the I/O unit uses the same`
22			`clock as the CPU (which greatly simplifies its design).`
23
24			`<P>The interface towards the CPU consist of the following signals:`
25
26			`<TABLE>`
27			`<TR><TD>ADR_IO</TD><TD>The number of an individual I/O register`
28			`</TD></TR><TR><TD>DIN</TD><TD>Data to an I/O register (I/O write)`
29			`</TD></TR><TR><TD>RD_IO</TD><TD>Read Strobe`
30			`</TD></TR><TR><TD>WR_IO</TD><TD>Write Strobe`
31			`</TD></TR><TR><TD>DOUT</TD><TD>Data from an I/O register (I/O read cycle.`
32			`</TD></TR>`
33			`</TABLE>`
34			`<P>These signals are well known from other I/O devices like UARTs,`
35			`Ethernet Controllers, and the like.`
36
37			`<P>The CPU supports two kinds of accesses to I/O registers: I/O reads`
38			`(with the IN or LDS instructions, but also for the skip instructions`
39			`SBIC and SBIS), and I/O writes (with the OUT or STS instructions,`
40			`but also with the bit instructions CBI and SBI).`
41
42			`<P>The skip instructions SBIC and SBIS execute in 2 cycles; in the first`
43			`cycle an I/O read is performed while the skip (or not) decision is made`
44			`in the second cycle. The reason for this is that the combinational delay`
45			`for a single cycle would have been too long.`
46
47			`<P>From the I/O unit's perspective, I/O reads and writes are performed`
48			`in a single cycle (even if the CPU needs another cycle to complete an`
49			`instruction.`
50
51			`<P>The I/O unit generates an interrupt vector on its <STRONG>INTVEC</STRONG> output.`
52			`The upper bit of the <STRONG>INTVEC</STRONG> output is set if an interrupt is pending.`
53
54			`<H2><A NAME="section_1_2">8.2 CLR Signal</A></H2>`
55
56			`<P>Some I/O components need a <STRONG>CLR</STRONG> signal to bring them into a defined state.`
57			`The <STRONG>CLR</STRONG> signal of the CPU is used for this purpose.`
58
59			`<H2><A NAME="section_1_3">8.3 Connection the FPGA Pins</A></H2>`
60
61			`<P>The remaining signals into and out of the I/O unit are more or less`
62			`directly connected to FPGA pins.`
63
64			`<P>The <STRONG>RX</STRONG> input comes from an RS232 receiver/driver chip and is the serial`
65			`input for an UART (active low). The TX output (also active low) is the`
66			`serial output from that UART and goes back to the RS232 receiver/driver chip:`
67
68			`<P><br>`
69
70			`<pre class="vhdl">`
71
72			`89 I_RX => I_RX,`
73			`90`
74			`91 Q_TX => Q_TX,`
75			`<pre class="filename">`
76			`src/io.vhd`
77			`</pre></pre>`
78			`<P>`
79
80			`<P>The <STRONG>SWITCH</STRONG> input comes from a DIP switch on the board.`
81			`The values of the switch can be read from I/O register <STRONG>PINB</STRONG> (0x36).`
82
83			`<P><br>`
84
85			`<pre class="vhdl">`
86
87			`132 when X"36" => Q_DOUT <= I_SWITCH; -- PINB`
88			`<pre class="filename">`
89			`src/io.vhd`
90			`</pre></pre>`
91			`<P>`
92
93			`<P><br>`
94
95			`<P>The 7_<STRONG>SEGMENT</STRONG> output drives the 7 segments of a 7-segment display.`
96			`This output can be set from software by writing to the <STRONG>PORTB</STRONG> (0x38)`
97			`I/O register. The segments can also be driven by a debug function which`
98			`shows the current <STRONG>PC</STRONG> and the current opcode of the CPU.`
99
100			`<P><br>`
101
102			`<pre class="vhdl">`
103
104			`147 when X"38" => Q_7_SEGMENT <= I_DIN(6 downto 0); -- PORTB`
105			`<pre class="filename">`
106			`src/io.vhd`
107			`</pre></pre>`
108			`<P>`
109
110			`<P><br>`
111
112			`<P>The choice between the debug display and the software controlled`
113			`display function is made by the DIP switch setting:`
114
115			`<P><br>`
116
117			`<pre class="vhdl">`
118
119			`183`
120			`<pre class="filename">`
121			`src/avr_fpga.vhd`
122			`</pre></pre>`
123			`<P>`
124
125			`<P><br>`
126
127			`<H2><A NAME="section_1_4">8.4 I/O Read</A></H2>`
128
129			`<P>I/O read cycles are indicated by the <STRONG>RD_IO</STRONG> signal. If <STRONG>RD_IO</STRONG> is applied,`
130			`then the address of the I/O register to be read is provided on the <STRONG>ADR_IO</STRONG>`
131			`input and the value of that register is expected on <STRONG>DOUT</STRONG> at the next`
132			`<STRONG>CLK</STRONG> edge.`
133
134			`<P>This is accomplished by the I/O read process:`
135
136			`<P><br>`
137
138			`<pre class="vhdl">`
139
140			`98 iord: process(I_ADR_IO, I_SWITCH,`
141			`99 U_RX_DATA, U_RX_READY, L_RX_INT_ENABLED,`
142			`100 U_TX_BUSY, L_TX_INT_ENABLED)`
143			`101 begin`
144			`102 -- addresses for mega8 device (use iom8.h or #define __AVR_ATmega8__).`
145			`103 --`
146			`104 case I_ADR_IO is`
147			`105 when X"2A" => Q_DOUT <= -- UCSRB:`
148			`106 L_RX_INT_ENABLED -- Rx complete int enabled.`
149			`107 & L_TX_INT_ENABLED -- Tx complete int enabled.`
150			`108 & L_TX_INT_ENABLED -- Tx empty int enabled.`
151			`109 & '1' -- Rx enabled`
152			`110 & '1' -- Tx enabled`
153			`111 & '0' -- 8 bits/char`
154			`112 & '0' -- Rx bit 8`
155			`113 & '0'; -- Tx bit 8`
156			`114 when X"2B" => Q_DOUT <= -- UCSRA:`
157			`115 U_RX_READY -- Rx complete`
158			`116 & not U_TX_BUSY -- Tx complete`
159			`117 & not U_TX_BUSY -- Tx ready`
160			`118 & '0' -- frame error`
161			`119 & '0' -- data overrun`
162			`120 & '0' -- parity error`
163			`121 & '0' -- double dpeed`
164			`122 & '0'; -- multiproc mode`
165			`123 when X"2C" => Q_DOUT <= U_RX_DATA; -- UDR`
166			`124 when X"40" => Q_DOUT <= -- UCSRC`
167			`125 '1' -- URSEL`
168			`126 & '0' -- asynchronous`
169			`127 & "00" -- no parity`
170			`128 & '1' -- two stop bits`
171			`129 & "11" -- 8 bits/char`
172			`130 & '0'; -- rising clock edge`
173			`131`
174			`132 when X"36" => Q_DOUT <= I_SWITCH; -- PINB`
175			`133 when others => Q_DOUT <= X"AA";`
176			`134 end case;`
177			`135 end process;`
178			`<pre class="filename">`
179			`src/io.vhd`
180			`</pre></pre>`
181			`<P>`
182
183			`<P><br>`
184
185			`<P>I/O registers that are not implemented (i.e almost all) set <STRONG>DOUT</STRONG>`
186			`to 0xAA as a debugging aid.`
187
188			`<P>The outputs of sub-components (like the UART) are selected in the I/O read`
189			`process.`
190
191			`<H2><A NAME="section_1_5">8.5 I/O Write</A></H2>`
192
193			`<P>I/O write cycles are indicated by the <STRONG>WR_IO</STRONG> signal. If <STRONG>WR_IO</STRONG> is applied,`
194			`then the address of the I/O register to be written is provided on the <STRONG>ADR_IO</STRONG>`
195			`input and the value to be written is supplied on the DIN input:`
196
197			`<P><br>`
198
199			`<pre class="vhdl">`
200
201			`139 iowr: process(I_CLK)`
202			`140 begin`
203			`141 if (rising_edge(I_CLK)) then`
204			`142 if (I_CLR = '1') then`
205			`143 L_RX_INT_ENABLED <= '0';`
206			`144 L_TX_INT_ENABLED <= '0';`
207			`145 elsif (I_WE_IO = '1') then`
208			`146 case I_ADR_IO is`
209			`147 when X"38" => Q_7_SEGMENT <= I_DIN(6 downto 0); -- PORTB`
210			`148 L_LEDS <= not L_LEDS;`
211			`149 when X"40" => -- handled by uart`
212			`150 when X"41" => -- handled by uart`
213			`151 when X"43" => L_RX_INT_ENABLED <= I_DIN(0);`
214			`152 L_TX_INT_ENABLED <= I_DIN(1);`
215			`153 when others =>`
216			`154 end case;`
217			`155 end if;`
218			`156 end if;`
219			`157 end process;`
220			`<pre class="filename">`
221			`src/io.vhd`
222			`</pre></pre>`
223			`<P>`
224
225			`<P><br>`
226
227			`<P>In the I/O read process the outputs of sub-component were multiplexed`
228			`into the final output <STRONG>DOUT</STRONG> and hence their register numbers (like 0x2C`
229			`for the <STRONG>UDR</STRONG> read register) were visible, In the I/O write process, however,`
230			`the inputs of sub-components (again like 0x2C for the <STRONG>UDR</STRONG> write register)`
231			`are not visible in the write process and decoding of the <STRONG>WR</STRONG> (and <STRONG>RD</STRONG> where`
232			`needed) strobes for sub components is done outside of these processes:`
233
234			`<P><br>`
235
236			`<pre class="vhdl">`
237
238			`182 L_WE_UART <= I_WE_IO when (I_ADR_IO = X"2C") else '0'; -- write UART UDR`
239			`183 L_RD_UART <= I_RD_IO when (I_ADR_IO = X"2C") else '0'; -- read UART UDR`
240			`184`
241			`<pre class="filename">`
242			`src/io.vhd`
243			`</pre></pre>`
244			`<P>`
245
246			`<P><br>`
247
248			`<H2><A NAME="section_1_6">8.6 Interrupts</A></H2>`
249
250			`<P>Some I/O components raise interrupts, which are coordinated in the`
251			`I/O interrupt process:`
252
253			`<P><br>`
254
255			`<pre class="vhdl">`
256
257			`161 ioint: process(I_CLK)`
258			`162 begin`
259			`163 if (rising_edge(I_CLK)) then`
260			`164 if (I_CLR = '1') then`
261			`165 L_INTVEC <= "000000";`
262			`166 else`
263			`167 if (L_RX_INT_ENABLED and U_RX_READY) = '1' then`
264			`168 if (L_INTVEC(5) = '0') then -- no interrupt pending`
265			`169 L_INTVEC <= "101011"; -- _VECTOR(11)`
266			`170 end if;`
267			`171 elsif (L_TX_INT_ENABLED and not U_TX_BUSY) = '1' then`
268			`172 if (L_INTVEC(5) = '0') then -- no interrupt pending`
269			`173 L_INTVEC <= "101100"; -- _VECTOR(12)`
270			`174 end if;`
271			`175 else -- no interrupt`
272			`176 L_INTVEC <= "000000";`
273			`177 end if;`
274			`178 end if;`
275			`179 end if;`
276			`180 end process;`
277			`<pre class="filename">`
278			`src/io.vhd`
279			`</pre></pre>`
280			`<P>`
281
282			`<P><br>`
283
284			`<H2><A NAME="section_1_7">8.7 The UART</A></H2>`
285
286			`<P>The UART is an important facility for debugging programs that are more`
287			`complex than out <STRONG>hello.c</STRONG>. We use a fixed baud rate of 38400 Baud`
288			`and a fixed data format of 8 data bits and 2 stop bits.`
289			`Therefore the corresponding bits in the UART control registers of the`
290			`original AVR CPU are not implemented. The fixed values are properly`
291			`reported, however.`
292
293			`<P>The UART consists of 3 independent sub-components: a baud rate generator,`
294			`a receiver, and a transmitter.`
295
296			`<H3><A NAME="section_1_7_1">8.7.1 The UART Baud Rate Generator</A></H3>`
297
298			`<P>The baud rate generator is clocked with a frequency of <STRONG>clock_freq</STRONG>`
299			`and is supposed to generate a x1 clock of <STRONG>baud_rate</STRONG> for the transmitter`
300			`and a x16 clock of 16*<STRONG>baud_rate</STRONG> for the receiver.`
301
302			`<P>The x16 clock is generated like this:`
303
304			`<P><br>`
305
306			`<pre class="vhdl">`
307
308			`54`
309			`55 baud16: process(I_CLK)`
310			`56 begin`
311			`57 if (rising_edge(I_CLK)) then`
312			`58 if (I_CLR = '1') then`
313			`59 L_COUNTER <= X"00000000";`
314			`60 elsif (L_COUNTER >= LIMIT) then`
315			`61 L_COUNTER <= L_COUNTER - LIMIT;`
316			`62 else`
317			`63 L_COUNTER <= L_COUNTER + BAUD_16;`
318			`64 end if;`
319			`65 end if;`
320			`66 end process;`
321			`67`
322			`68 baud1: process(I_CLK)`
323			`<pre class="filename">`
324			`src/baudgen.vhd`
325			`</pre></pre>`
326			`<P>`
327
328			`<P><br>`
329
330			`<P>We have done a little trick here. Most baud rate generators divide the`
331			`input clock by a fixed integer number (like the one shown below for the`
332			`x1 clock). That is fine if the input clock is a multiple of the output`
333			`clock. More often than not is the CPU clock not a multiple of the the`
334			`baud rate. Therefore, if an integer divider is used (like in the original`
335			`AVR CPU, where the integer divisor was written into the UBRR I/O register)`
336			`then the error in the baud rate cumulates over all bits transmitted. This can`
337			`cause transmission errors when many characters are sent back to back.`
338			`An integer divider would have set <STRONG>L_COUNTER</STRONG> to 0 after reaching <STRONG>LIMIT</STRONG>,`
339			`which would have cause an absolute error of <STRONG>COUNTER</STRONG> - <STRONG>LIMIT</STRONG>. What we`
340			`do instead is to subtract <STRONG>LIMIT</STRONG>, which does no discard the error but`
341			`makes the next cycle a little shorter instead.`
342
343			`<P>Instead of using a fixed baud rate interval of N times the clock interval`
344			`(as fixed integer dividers would), we have used a variable baud rate interval;`
345			`the length of the interval varies slightly over time, but the total error`
346			`remains bounded. The error does not cumulate as for fixed integer`
347			`dividers.`
348
349			`<P>If you want to make the baud rate programmable, then you can replace the`
350			`generic <STRONG>baud_rate</STRONG> by a signal (and the trick would still work).`
351
352			`<P>The x1 clock is generated by dividing the x16 clock by 16:`
353
354			`<P><br>`
355
356			`<pre class="vhdl">`
357
358			`70 if (rising_edge(I_CLK)) then`
359			`71 if (I_CLR = '1') then`
360			`72 L_CNT_16 <= "0000";`
361			`73 elsif (L_CE_16 = '1') then`
362			`74 L_CNT_16 <= L_CNT_16 + "0001";`
363			`75 end if;`
364			`76 end if;`
365			`77 end process;`
366			`78`
367			`79 L_CE_16 <= '1' when (L_COUNTER >= LIMIT) else '0';`
368			`80 Q_CE_16 <= L_CE_16;`
369			`81 Q_CE_1 <= L_CE_16 when L_CNT_16 = "1111" else '0';`
370			`<pre class="filename">`
371			`src/baudgen.vhd`
372			`</pre></pre>`
373			`<P>`
374
375			`<P><br>`
376
377			`<H3><A NAME="section_1_7_2">8.7.2 The UART Transmitter</A></H3>`
378
379			`<P>The UART transmitter is a shift register that is loaded with`
380			`the character to be transmitted (prepended with a start bit):`
381
382			`<P><br>`
383
384			`<pre class="vhdl">`
385
386			`67 elsif (L_FLAG /= I_FLAG) then -- new byte`
387			`68 Q_TX <= '0'; -- start bit`
388			`69 L_BUF <= I_DATA; -- data bits`
389			`70 L_TODO <= "1001";`
390			`71 end if;`
391			`<pre class="filename">`
392			`src/uart_tx.vhd`
393			`</pre></pre>`
394			`<P>`
395
396			`<P><br>`
397
398			`<P>The <STRONG>TODO</STRONG> signal holds the number of bits that remain to be shifted out.`
399			`The transmitter is clocked with the x1 baud rate:`
400
401			`<P><br>`
402
403			`<pre class="vhdl">`
404
405			`59 elsif (I_CE_1 = '1') then`
406			`60 if (L_TODO /= "0000") then -- transmitting`
407			`61 Q_TX <= L_BUF(0); -- next bit`
408			`62 L_BUF <= '1' & L_BUF(7 downto 1);`
409			`63 if (L_TODO = "0001") then`
410			`64 L_FLAG <= I_FLAG;`
411			`65 end if;`
412			`66 L_TODO <= L_TODO - "0001";`
413			`67 elsif (L_FLAG /= I_FLAG) then -- new byte`
414			`68 Q_TX <= '0'; -- start bit`
415			`69 L_BUF <= I_DATA; -- data bits`
416			`70 L_TODO <= "1001";`
417			`71 end if;`
418			`72 end if;`
419			`<pre class="filename">`
420			`src/uart_tx.vhd`
421			`</pre></pre>`
422			`<P>`
423
424			`<P><br>`
425
426			`<H3><A NAME="section_1_7_3">8.7.3 The UART Receiver</A></H3>`
427
428			`<P>The UART transmitter runs synchronously with the CPU clock; but the UART`
429			`receiver does not. We therefore clock the receiver input twice`
430			`in order to synchronize it with the CPU clock:`
431
432			`<P><br>`
433
434			`<pre class="vhdl">`
435
436			`56 process(I_CLK)`
437			`57 begin`
438			`58 if (rising_edge(I_CLK)) then`
439			`59 if (I_CLR = '1') then`
440			`60 L_SERIN <= '1';`
441			`61 L_SER_HOT <= '1';`
442			`62 else`
443			`63 L_SERIN <= I_RX;`
444			`64 L_SER_HOT <= L_SERIN;`
445			`65 end if;`
446			`66 end if;`
447			`67 end process;`
448			`<pre class="filename">`
449			`src/uart_rx.vhd`
450			`</pre></pre>`
451			`<P>`
452
453			`<P><br>`
454
455			`<P>The key signal in the UART receiver is <STRONG>POSITION</STRONG> which is the current`
456			`position within the received character in units if 1/16 bit time. When the`
457			`receiver is idle and a start bit is received, then <STRONG>POSITION</STRONG> is reset to`
458			`1:`
459
460			`<P><br>`
461
462			`<pre class="vhdl">`
463
464			`86 if (L_POSITION = X"00") then -- uart idle`
465			`87 L_BUF <= "1111111111";`
466			`88 if (L_SER_HOT = '0') then -- start bit received`
467			`89 L_POSITION <= X"01";`
468			`90 end if;`
469			`<pre class="filename">`
470			`src/uart_rx.vhd`
471			`</pre></pre>`
472			`<P>`
473
474			`<P><br>`
475
476			`<P>At every subsequent edge of the 16x baud rate, <STRONG>POSITION</STRONG> is incremented`
477			`and the receiver input (<STRONG>SER_HOT</STRONG>) input is checked at the middle of each`
478			`bit (i.e. when <STRONG>POSITION[3:0]</STRONG> = "0111").`
479			`If the start bit has disappeared at the middle of the bit, then this is`
480			`considered noise on the line rather than a valid start bit:`
481
482			`<P><br>`
483
484			`<pre class="vhdl">`
485
486			`93 if (L_POSITION(3 downto 0) = "0111") then -- 1/2 bit`
487			`94 L_BUF <= L_SER_HOT & L_BUF(9 downto 1); -- sample data`
488			`95 --`
489			`96 -- validate start bit`
490			`97 --`
491			`98 if (START_BIT and L_SER_HOT = '1') then -- 1/2 start bit`
492			`99 L_POSITION <= X"00";`
493			`100 end if;`
494			`101`
495			`102 if (STOP_BIT) then -- 1/2 stop bit`
496			`103 Q_DATA <= L_BUF(9 downto 2);`
497			`104 end if;`
498			`<pre class="filename">`
499			`src/uart_rx.vhd`
500			`</pre></pre>`
501			`<P>`
502
503			`<P><br>`
504
505			`<P>Reception of a byte already finishes at 3/4 of the stop bit. This is to`
506			`allow for cumulated baud rate errors of 1/4 bit time (or about 2.5 %`
507			`baud rate error for 10 bit (1 start, 8 data, and 1 stop bit) transmissions).`
508			`The received data is stored in <STRONG>DATA</STRONG>:`
509
510			`<P><br>`
511
512			`<pre class="vhdl">`
513
514			`105 elsif (STOP_POS) then -- 3/4 stop bit`
515			`106 L_FLAG <= L_FLAG xor (L_BUF(9) and not L_BUF(0));`
516			`107 L_POSITION <= X"00";`
517			`<pre class="filename">`
518			`src/uart_rx.vhd`
519			`</pre></pre>`
520			`<P>`
521
522			`<P><br>`
523
524			`<P>If a greater tolerance against baud rate errors is needed, then one can`
525			`decrease <STRONG>STOP_POS</STRONG> a little, but generally it would be safer to use 2`
526			`stop bits on the sender side.`
527
528			`<P>This finalizes the description of the FPGA. We will proceed with the`
529			`design flow in the next lesson.`
530
531			`<P><hr><BR>`
532			`<table class="ttop"><th class="tpre"><a href="07_Opcode_Decoder.html">Previous Lesson</a></th><th class="ttop"><a href="toc.html">Table of Content</a></th><th class="tnxt"><a href="09_Toolchain_Setup.html">Next Lesson</a></th></table>`
533			`</BODY>`
534			`</HTML>`