| 1 |
6 |
jdoin |
Release 13.1 Map O.40d (nt)
|
| 2 |
|
|
Xilinx Mapping Report File for Design 'debounce_atlys_top'
|
| 3 |
|
|
|
| 4 |
|
|
Design Information
|
| 5 |
|
|
------------------
|
| 6 |
|
|
Command Line : map -intstyle ise -p xc6slx45-csg324-2 -w -logic_opt off -ol
|
| 7 |
|
|
high -xe n -t 1 -xt 0 -register_duplication off -r 4 -global_opt area
|
| 8 |
|
|
-equivalent_register_removal on -mt 2 -detail -ir off -pr off -lc area -power
|
| 9 |
|
|
off -o debounce_atlys_top_map.ncd debounce_atlys_top.ngd debounce_atlys_top.pcf
|
| 10 |
|
|
Target Device : xc6slx45
|
| 11 |
|
|
Target Package : csg324
|
| 12 |
|
|
Target Speed : -2
|
| 13 |
|
|
Mapper Version : spartan6 -- $Revision: 1.55 $
|
| 14 |
8 |
jdoin |
Mapped Date : Mon Aug 15 23:25:20 2011
|
| 15 |
6 |
jdoin |
|
| 16 |
|
|
Design Summary
|
| 17 |
|
|
--------------
|
| 18 |
|
|
Number of errors: 0
|
| 19 |
|
|
Number of warnings: 0
|
| 20 |
|
|
Slice Logic Utilization:
|
| 21 |
7 |
jdoin |
Number of Slice Registers: 42 out of 54,576 1%
|
| 22 |
|
|
Number used as Flip Flops: 42
|
| 23 |
6 |
jdoin |
Number used as Latches: 0
|
| 24 |
|
|
Number used as Latch-thrus: 0
|
| 25 |
|
|
Number used as AND/OR logics: 0
|
| 26 |
7 |
jdoin |
Number of Slice LUTs: 37 out of 27,288 1%
|
| 27 |
|
|
Number used as logic: 36 out of 27,288 1%
|
| 28 |
6 |
jdoin |
Number using O6 output only: 18
|
| 29 |
7 |
jdoin |
Number using O5 output only: 11
|
| 30 |
|
|
Number using O5 and O6: 7
|
| 31 |
6 |
jdoin |
Number used as ROM: 0
|
| 32 |
|
|
Number used as Memory: 0 out of 6,408 0%
|
| 33 |
7 |
jdoin |
Number used exclusively as route-thrus: 1
|
| 34 |
|
|
Number with same-slice register load: 0
|
| 35 |
6 |
jdoin |
Number with same-slice carry load: 1
|
| 36 |
|
|
Number with other load: 0
|
| 37 |
|
|
|
| 38 |
|
|
Slice Logic Distribution:
|
| 39 |
7 |
jdoin |
Number of occupied Slices: 19 out of 6,822 1%
|
| 40 |
|
|
Number of LUT Flip Flop pairs used: 56
|
| 41 |
|
|
Number with an unused Flip Flop: 20 out of 56 35%
|
| 42 |
|
|
Number with an unused LUT: 19 out of 56 33%
|
| 43 |
|
|
Number of fully used LUT-FF pairs: 17 out of 56 30%
|
| 44 |
6 |
jdoin |
Number of unique control sets: 3
|
| 45 |
|
|
Number of slice register sites lost
|
| 46 |
7 |
jdoin |
to control set restrictions: 6 out of 54,576 1%
|
| 47 |
6 |
jdoin |
|
| 48 |
|
|
A LUT Flip Flop pair for this architecture represents one LUT paired with
|
| 49 |
|
|
one Flip Flop within a slice. A control set is a unique combination of
|
| 50 |
|
|
clock, reset, set, and enable signals for a registered element.
|
| 51 |
|
|
The Slice Logic Distribution report is not meaningful if the design is
|
| 52 |
|
|
over-mapped for a non-slice resource or if Placement fails.
|
| 53 |
|
|
|
| 54 |
|
|
IO Utilization:
|
| 55 |
7 |
jdoin |
Number of bonded IOBs: 31 out of 218 14%
|
| 56 |
|
|
Number of LOCed IOBs: 31 out of 31 100%
|
| 57 |
6 |
jdoin |
|
| 58 |
|
|
Specific Feature Utilization:
|
| 59 |
|
|
Number of RAMB16BWERs: 0 out of 116 0%
|
| 60 |
|
|
Number of RAMB8BWERs: 0 out of 232 0%
|
| 61 |
|
|
Number of BUFIO2/BUFIO2_2CLKs: 0 out of 32 0%
|
| 62 |
|
|
Number of BUFIO2FB/BUFIO2FB_2CLKs: 0 out of 32 0%
|
| 63 |
|
|
Number of BUFG/BUFGMUXs: 1 out of 16 6%
|
| 64 |
|
|
Number used as BUFGs: 1
|
| 65 |
|
|
Number used as BUFGMUX: 0
|
| 66 |
|
|
Number of DCM/DCM_CLKGENs: 0 out of 8 0%
|
| 67 |
|
|
Number of ILOGIC2/ISERDES2s: 0 out of 376 0%
|
| 68 |
|
|
Number of IODELAY2/IODRP2/IODRP2_MCBs: 0 out of 376 0%
|
| 69 |
|
|
Number of OLOGIC2/OSERDES2s: 0 out of 376 0%
|
| 70 |
|
|
Number of BSCANs: 0 out of 4 0%
|
| 71 |
|
|
Number of BUFHs: 0 out of 256 0%
|
| 72 |
|
|
Number of BUFPLLs: 0 out of 8 0%
|
| 73 |
|
|
Number of BUFPLL_MCBs: 0 out of 4 0%
|
| 74 |
|
|
Number of DSP48A1s: 0 out of 58 0%
|
| 75 |
|
|
Number of ICAPs: 0 out of 1 0%
|
| 76 |
|
|
Number of MCBs: 0 out of 2 0%
|
| 77 |
|
|
Number of PCILOGICSEs: 0 out of 2 0%
|
| 78 |
|
|
Number of PLL_ADVs: 0 out of 4 0%
|
| 79 |
|
|
Number of PMVs: 0 out of 1 0%
|
| 80 |
|
|
Number of STARTUPs: 0 out of 1 0%
|
| 81 |
|
|
Number of SUSPEND_SYNCs: 0 out of 1 0%
|
| 82 |
|
|
|
| 83 |
7 |
jdoin |
Average Fanout of Non-Clock Nets: 2.37
|
| 84 |
6 |
jdoin |
|
| 85 |
8 |
jdoin |
Peak Memory Usage: 298 MB
|
| 86 |
|
|
Total REAL time to MAP completion: 15 secs
|
| 87 |
6 |
jdoin |
Total CPU time to MAP completion (all processors): 11 secs
|
| 88 |
|
|
|
| 89 |
|
|
Table of Contents
|
| 90 |
|
|
-----------------
|
| 91 |
|
|
Section 1 - Errors
|
| 92 |
|
|
Section 2 - Warnings
|
| 93 |
|
|
Section 3 - Informational
|
| 94 |
|
|
Section 4 - Removed Logic Summary
|
| 95 |
|
|
Section 5 - Removed Logic
|
| 96 |
|
|
Section 6 - IOB Properties
|
| 97 |
|
|
Section 7 - RPMs
|
| 98 |
|
|
Section 8 - Guide Report
|
| 99 |
|
|
Section 9 - Area Group and Partition Summary
|
| 100 |
|
|
Section 10 - Timing Report
|
| 101 |
|
|
Section 11 - Configuration String Information
|
| 102 |
|
|
Section 12 - Control Set Information
|
| 103 |
|
|
Section 13 - Utilization by Hierarchy
|
| 104 |
|
|
|
| 105 |
|
|
Section 1 - Errors
|
| 106 |
|
|
------------------
|
| 107 |
|
|
|
| 108 |
|
|
Section 2 - Warnings
|
| 109 |
|
|
--------------------
|
| 110 |
|
|
|
| 111 |
|
|
Section 3 - Informational
|
| 112 |
|
|
-------------------------
|
| 113 |
|
|
INFO:Map:284 - Map is running with the multi-threading option on. Map currently
|
| 114 |
|
|
supports the use of up to 2 processors. Based on the the user options and
|
| 115 |
|
|
machine load, Map will use 2 processors during this run.
|
| 116 |
|
|
INFO:LIT:243 - Logical network gclk_i_BUFGP/N2 has no load.
|
| 117 |
|
|
INFO:LIT:243 - Logical network gclk_i_BUFGP/N3 has no load.
|
| 118 |
|
|
INFO:MapLib:562 - No environment variables are currently set.
|
| 119 |
|
|
INFO:LIT:244 - All of the single ended outputs in this design are using slew
|
| 120 |
|
|
rate limited output drivers. The delay on speed critical single ended outputs
|
| 121 |
|
|
can be dramatically reduced by designating them as fast outputs.
|
| 122 |
|
|
INFO:Pack:1716 - Initializing temperature to 85.000 Celsius. (default - Range:
|
| 123 |
|
|
0.000 to 85.000 Celsius)
|
| 124 |
|
|
INFO:Pack:1720 - Initializing voltage to 1.140 Volts. (default - Range: 1.140 to
|
| 125 |
|
|
1.260 Volts)
|
| 126 |
|
|
INFO:Map:215 - The Interim Design Summary has been generated in the MAP Report
|
| 127 |
|
|
(.mrp).
|
| 128 |
|
|
INFO:Pack:1650 - Map created a placed design.
|
| 129 |
|
|
|
| 130 |
|
|
Section 4 - Removed Logic Summary
|
| 131 |
|
|
---------------------------------
|
| 132 |
|
|
2 block(s) removed
|
| 133 |
|
|
2 block(s) optimized away
|
| 134 |
|
|
2 signal(s) removed
|
| 135 |
|
|
12 Block(s) redundant
|
| 136 |
|
|
|
| 137 |
|
|
Section 5 - Removed Logic
|
| 138 |
|
|
-------------------------
|
| 139 |
|
|
|
| 140 |
|
|
The trimmed logic report below shows the logic removed from your design due to
|
| 141 |
|
|
sourceless or loadless signals, and VCC or ground connections. If the removal
|
| 142 |
|
|
of a signal or symbol results in the subsequent removal of an additional signal
|
| 143 |
|
|
or symbol, the message explaining that second removal will be indented. This
|
| 144 |
|
|
indentation will be repeated as a chain of related logic is removed.
|
| 145 |
|
|
|
| 146 |
|
|
To quickly locate the original cause for the removal of a chain of logic, look
|
| 147 |
|
|
above the place where that logic is listed in the trimming report, then locate
|
| 148 |
|
|
the lines that are least indented (begin at the leftmost edge).
|
| 149 |
|
|
|
| 150 |
|
|
The signal "gclk_i_BUFGP/N2" is sourceless and has been removed.
|
| 151 |
|
|
The signal "gclk_i_BUFGP/N3" is sourceless and has been removed.
|
| 152 |
|
|
Unused block "gclk_i_BUFGP/XST_GND" (ZERO) removed.
|
| 153 |
|
|
Unused block "gclk_i_BUFGP/XST_VCC" (ONE) removed.
|
| 154 |
|
|
|
| 155 |
|
|
Optimized Block(s):
|
| 156 |
|
|
TYPE BLOCK
|
| 157 |
|
|
GND XST_GND
|
| 158 |
|
|
VCC XST_VCC
|
| 159 |
|
|
|
| 160 |
|
|
Redundant Block(s):
|
| 161 |
|
|
TYPE BLOCK
|
| 162 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<11>_rt
|
| 163 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<10>_rt
|
| 164 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<9>_rt
|
| 165 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<8>_rt
|
| 166 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<7>_rt
|
| 167 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<6>_rt
|
| 168 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<5>_rt
|
| 169 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<4>_rt
|
| 170 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<3>_rt
|
| 171 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<2>_rt
|
| 172 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_cy<1>_rt
|
| 173 |
|
|
LUT1 Inst_sw_debouncer/Mcount_cnt_reg_xor<12>_rt
|
| 174 |
|
|
|
| 175 |
|
|
Section 6 - IOB Properties
|
| 176 |
|
|
--------------------------
|
| 177 |
|
|
|
| 178 |
|
|
+---------------------------------------------------------------------------------------------------------------------------------------------------------+
|
| 179 |
|
|
| IOB Name | Type | Direction | IO Standard | Diff | Drive | Slew | Reg (s) | Resistor | IOB |
|
| 180 |
|
|
| | | | | Term | Strength | Rate | | | Delay |
|
| 181 |
|
|
+---------------------------------------------------------------------------------------------------------------------------------------------------------+
|
| 182 |
|
|
| dbg_o<0> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 183 |
|
|
| dbg_o<1> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 184 |
|
|
| dbg_o<2> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 185 |
|
|
| dbg_o<3> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 186 |
|
|
| dbg_o<4> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 187 |
|
|
| dbg_o<5> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 188 |
|
|
| dbg_o<6> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 189 |
|
|
| dbg_o<7> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 190 |
|
|
| dbg_o<8> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 191 |
|
|
| dbg_o<9> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 192 |
|
|
| dbg_o<10> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 193 |
|
|
| dbg_o<11> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 194 |
|
|
| dbg_o<12> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 195 |
|
|
| dbg_o<13> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 196 |
|
|
| dbg_o<14> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 197 |
|
|
| dbg_o<15> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 198 |
|
|
| gclk_i | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 199 |
|
|
| led_o<0> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 200 |
|
|
| led_o<1> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 201 |
|
|
| led_o<2> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 202 |
|
|
| led_o<3> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 203 |
|
|
| led_o<4> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 204 |
|
|
| led_o<5> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 205 |
|
|
| led_o<6> | IOB | OUTPUT | LVCMOS25 | | 12 | SLOW | | | |
|
| 206 |
|
|
| sw_i<0> | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 207 |
|
|
| sw_i<1> | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 208 |
|
|
| sw_i<2> | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 209 |
|
|
| sw_i<3> | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 210 |
|
|
| sw_i<4> | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 211 |
|
|
| sw_i<5> | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 212 |
|
|
| sw_i<6> | IOB | INPUT | LVCMOS25 | | | | | | |
|
| 213 |
|
|
+---------------------------------------------------------------------------------------------------------------------------------------------------------+
|
| 214 |
|
|
|
| 215 |
|
|
Section 7 - RPMs
|
| 216 |
|
|
----------------
|
| 217 |
|
|
|
| 218 |
|
|
Section 8 - Guide Report
|
| 219 |
|
|
------------------------
|
| 220 |
|
|
Guide not run on this design.
|
| 221 |
|
|
|
| 222 |
|
|
Section 9 - Area Group and Partition Summary
|
| 223 |
|
|
--------------------------------------------
|
| 224 |
|
|
|
| 225 |
|
|
Partition Implementation Status
|
| 226 |
|
|
-------------------------------
|
| 227 |
|
|
|
| 228 |
|
|
No Partitions were found in this design.
|
| 229 |
|
|
|
| 230 |
|
|
-------------------------------
|
| 231 |
|
|
|
| 232 |
|
|
Area Group Information
|
| 233 |
|
|
----------------------
|
| 234 |
|
|
|
| 235 |
|
|
No area groups were found in this design.
|
| 236 |
|
|
|
| 237 |
|
|
----------------------
|
| 238 |
|
|
|
| 239 |
|
|
Section 10 - Timing Report
|
| 240 |
|
|
--------------------------
|
| 241 |
|
|
A logic-level (pre-route) timing report can be generated by using Xilinx static
|
| 242 |
|
|
timing analysis tools, Timing Analyzer (GUI) or TRCE (command line), with the
|
| 243 |
|
|
mapped NCD and PCF files. Please note that this timing report will be generated
|
| 244 |
|
|
using estimated delay information. For accurate numbers, please generate a
|
| 245 |
|
|
timing report with the post Place and Route NCD file.
|
| 246 |
|
|
|
| 247 |
|
|
For more information about the Timing Analyzer, consult the Xilinx Timing
|
| 248 |
|
|
Analyzer Reference Manual; for more information about TRCE, consult the Xilinx
|
| 249 |
|
|
Command Line Tools User Guide "TRACE" chapter.
|
| 250 |
|
|
|
| 251 |
|
|
Section 11 - Configuration String Details
|
| 252 |
|
|
-----------------------------------------
|
| 253 |
|
|
|
| 254 |
|
|
Section 12 - Control Set Information
|
| 255 |
|
|
------------------------------------
|
| 256 |
|
|
+-----------------------------------------------------------------------------------------------------------+
|
| 257 |
|
|
| Clock Signal | Reset Signal | Set Signal | Enable Signal | Slice Load Count | Bel Load Count |
|
| 258 |
|
|
+-----------------------------------------------------------------------------------------------------------+
|
| 259 |
7 |
jdoin |
| gclk_i_BUFGP | | | | 8 | 28 |
|
| 260 |
|
|
| gclk_i_BUFGP | | | Inst_sw_debouncer/strb_reg | 2 | 7 |
|
| 261 |
|
|
| gclk_i_BUFGP | | | lut107_31 | 2 | 7 |
|
| 262 |
6 |
jdoin |
+-----------------------------------------------------------------------------------------------------------+
|
| 263 |
|
|
|
| 264 |
|
|
Section 13 - Utilization by Hierarchy
|
| 265 |
|
|
-------------------------------------
|
| 266 |
|
|
+-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
|
| 267 |
|
|
| Module | Partition | Slices* | Slice Reg | LUTs | LUTRAM | BRAM/FIFO | DSP48A1 | BUFG | BUFIO | BUFR | DCM | PLL_ADV | Full Hierarchical Name |
|
| 268 |
|
|
+-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
|
| 269 |
7 |
jdoin |
| debounce_atlys_top/ | | 14/28 | 7/42 | 24/25 | 0/0 | 0/0 | 0/0 | 1/1 | 0/0 | 0/0 | 0/0 | 0/0 | debounce_atlys_top |
|
| 270 |
|
|
| +Inst_sw_debouncer | | 14/14 | 35/35 | 1/1 | 0/0 | 0/0 | 0/0 | 0/0 | 0/0 | 0/0 | 0/0 | 0/0 | debounce_atlys_top/Inst_sw_debouncer |
|
| 271 |
6 |
jdoin |
+-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------+
|
| 272 |
|
|
|
| 273 |
|
|
* Slices can be packed with basic elements from multiple hierarchies.
|
| 274 |
|
|
Therefore, a slice will be counted in every hierarchical module
|
| 275 |
|
|
that each of its packed basic elements belong to.
|
| 276 |
|
|
** For each column, there are two numbers reported /.
|
| 277 |
|
|
is the number of elements that belong to that specific hierarchical module.
|
| 278 |
|
|
is the total number of elements from that hierarchical module and any lower level
|
| 279 |
|
|
hierarchical modules below.
|
| 280 |
|
|
*** The LUTRAM column counts all LUTs used as memory including RAM, ROM, and shift registers.
|
