URL https://opencores.org/ocsvn/gecko3/gecko3/trunk

Subversion Repositories gecko3

[/] [gecko3/] [trunk/] [GECKO3COM/] [gecko3com-fw/] [firmware/] [gpif-design/] [gecko3main_gpif.c] - Blame information for rev 20

Go to most recent revision | Details | Compare with Previous | View Log


// This program configures the General Programmable Interface (GPIF) for FX2.     
// Please do not modify sections of text which are marked as "DO NOT EDIT ...". 
//                                                                                
// DO NOT EDIT ...                  
// GPIF Initialization              
// Interface Timing      Sync         
// Internal Ready Init   IntRdy=1     
// CTL Out Tristate-able Binary       
// SingleWrite WF Select     1     
// SingleRead WF Select      0     
// FifoWrite WF Select       3     
// FifoRead WF Select        2     
// Data Bus Idle Drive   Tristate     
// END DO NOT EDIT                  
 
// DO NOT EDIT ...       
// GPIF Wave Names       
// Wave 0   = Single R     
// Wave 1   = Single W     
// Wave 2   = FIFO Rea     
// Wave 3   = FIFO Wri     
 
// GPIF Ctrl Outputs   Level   
// CTL 0    = RDYU     CMOS        
// CTL 1    = WRU      CMOS        
// CTL 2    = RDYU     CMOS        
// CTL 3    = X2U_ex   CMOS        
// CTL 4    = U2X_th   CMOS        
// CTL 5    = unused   CMOS        
 
// GPIF Rdy Inputs         
// RDY0     = WRX            
// RDY1     = RDYX           
// RDY2     = unused         
// RDY3     = unused         
// RDY4     = unused         
// RDY5     = TCXpire        
// FIFOFlag = FIFOFlag       
// IntReady = IntReady       
// END DO NOT EDIT         
// DO NOT EDIT ...                                                                         
//                                                                                         
// GPIF Waveform 0: Single R                                                                
//                                                                                         
// Interval     0         1         2         3         4         5         6     Idle (7) 
//          _________ _________ _________ _________ _________ _________ _________ _________
//                                                                                         
// AddrMode Same Val  Same Val  Same Val  Same Val  Same Val  Same Val  Same Val           
// DataMode NO Data   NO Data   Activate  Activate  Activate  Activate  Activate           
// NextData SameData  SameData  SameData  SameData  SameData  SameData  SameData           
// Int Trig No Int    No Int    No Int    No Int    No Int    No Int    No Int             
// IF/Wait  IF        Wait 1    IF        Wait 1    Wait 1    Wait 1    Wait 1             
//   Term A WRX                 WRX                                                        
//   LFunc  AND                 AND                                                        
//   Term B WRX                 WRX                                                        
// Branch1  Then 1              ThenIdle                                                   
// Branch0  ElseIdle            ElseIdle                                                   
// Re-Exec  Yes                 Yes                                                        
// Sngl/CRC Default   Default   Default   Default   Default   Default   Default            
// RDYU         0         0         0         0         0         0         0         0    
// WRU          0         0         0         0         0         0         0         0    
// RDYU         0         1         1         1         1         1         1         0    
// X2U_ex       0         0         0         0         0         0         0         0    
// U2X_th       0         0         0         0         0         0         0         0    
// unused       0         0         0         0         0         0         0         0    
//                     
// END DO NOT EDIT     
// DO NOT EDIT ...                                                                         
//                                                                                         
// GPIF Waveform 1: Single W                                                                
//                                                                                         
// Interval     0         1         2         3         4         5         6     Idle (7) 
//          _________ _________ _________ _________ _________ _________ _________ _________
//                                                                                         
// AddrMode Same Val  Same Val  Same Val  Same Val  Same Val  Same Val  Same Val           
// DataMode NO Data   NO Data   Activate  NO Data   NO Data   NO Data   NO Data            
// NextData SameData  SameData  SameData  SameData  SameData  SameData  SameData           
// Int Trig No Int    No Int    No Int    No Int    No Int    No Int    No Int             
// IF/Wait  IF        IF        IF        IF        Wait 1    Wait 1    Wait 1             
//   Term A WRX       RDYX      RDYX      RDYX                                             
//   LFunc  OR        AND       AND       AND                                              
//   Term B WRX       RDYX      IntReady  RDYX                                             
// Branch1  ThenIdle  Then 2    ThenIdle  Then 3                                           
// Branch0  Else 1    Else 1    Else 3    ElseIdle                                         
// Re-Exec  No        No        Yes       No                                               
// Sngl/CRC Default   Default   Default   Default   Default   Default   Default            
// RDYU         0         0         0         0         0         0         0         0    
// WRU          0         1         1         1         1         1         1         0    
// RDYU         0         0         0         1         1         1         1         0    
// X2U_ex       0         0         0         0         0         0         0         0    
// U2X_th       0         0         0         0         0         0         0         0    
// unused       0         0         0         0         0         0         0         0    
//                     
// END DO NOT EDIT     
// DO NOT EDIT ...                                                                         
//                                                                                         
// GPIF Waveform 2: FIFO Rea                                                                
//                                                                                         
// Interval     0         1         2         3         4         5         6     Idle (7) 
//          _________ _________ _________ _________ _________ _________ _________ _________
//                                                                                         
// AddrMode Same Val  Same Val  Same Val  Same Val  Same Val  Same Val  Same Val           
// DataMode NO Data   NO Data   NO Data   Activate  Activate  NO Data   NO Data            
// NextData SameData  SameData  SameData  SameData  NextData  SameData  SameData           
// Int Trig No Int    No Int    No Int    No Int    Trig Int  No Int    No Int             
// IF/Wait  IF        IF        Wait 2    IF        Wait 1    IF        IF                 
//   Term A RDYX      RDYX                WRX                 WRX       WRX                
//   LFunc  !A AND B  !A AND B            AND                 AND       AND                
//   Term B WRX       WRX                 WRX                 WRX       WRX                
// Branch1  Then 1    Then 2              Then 3              ThenIdle  ThenIdle           
// Branch0  Else 0    Else 0              Else 4              ElseIdle  ElseIdle           
// Re-Exec  No        No                  Yes                 No        Yes                
// Sngl/CRC Default   Default   Default   Default   Default   Default   Default            
// RDYU         0         0         0         0         0         0         0         0    
// WRU          0         0         0         0         0         0         0         0    
// RDYU         0         0         1         1         1         0         0         0    
// X2U_ex       0         0         1         1         1         0         0         0    
// U2X_th       0         0         0         0         0         0         0         0    
// unused       0         0         0         0         0         0         0         0    
//                     
// END DO NOT EDIT     
// DO NOT EDIT ...                                                                         
//                                                                                         
// GPIF Waveform 3: FIFO Wri                                                                
//                                                                                         
// Interval     0         1         2         3         4         5         6     Idle (7) 
//          _________ _________ _________ _________ _________ _________ _________ _________
//                                                                                         
// AddrMode Same Val  Same Val  Same Val  Same Val  Same Val  Same Val  Same Val           
// DataMode NO Data   NO Data   NO Data   Activate  Activate  Activate  NO Data            
// NextData SameData  SameData  SameData  SameData  NextData  NextData  SameData           
// Int Trig No Int    No Int    No Int    No Int    No Int    Trig Int  No Int             
// IF/Wait  IF        Wait 1    IF        IF        IF        IF        IF                 
//   Term A WRX                 WRX       RDYX      FIFOFlag  RDYX      WRX                
//   LFunc  AND                 AND       AND       AND       AND       AND                
//   Term B WRX                 WRX       RDYX      FIFOFlag  RDYX      WRX                
// Branch1  ThenIdle            Then 2    Then 4    Then 4    Then 5    ThenIdle           
// Branch0  Else 1              Else 3    Else 3    Else 5    ElseIdle  ElseIdle           
// Re-Exec  No                  No        No        Yes       No        No                 
// Sngl/CRC Default   Default   Default   Default   Default   Default   Default            
// RDYU         0         0         0         0         0         0         0         0    
// WRU          0         1         1         1         1         0         0         0    
// RDYU         0         0         0         0         0         0         0         0    
// X2U_ex       0         0         0         0         0         0         0         0    
// U2X_th       0         0         0         0         0         0         0         0    
// unused       0         0         0         0         0         0         0         0    
//                     
// END DO NOT EDIT     
 
// GPIF Program Code                          
 
// DO NOT EDIT ...                            
#include "fx2.h"                            
#include "fx2regs.h"                        
#include "fx2sdly.h"     // SYNCDELAY macro 
// END DO NOT EDIT                            
 
// DO NOT EDIT ...                     
const char xdata WaveData[128] =
{
// Wave 0 
/* LenBr */ 0x8F,     0x01,     0xBF,     0x01,     0x01,     0x01,     0x01,     0x07,
/* Opcode*/ 0x01,     0x00,     0x03,     0x02,     0x02,     0x02,     0x02,     0x00,
/* Output*/ 0x00,     0x04,     0x04,     0x04,     0x04,     0x04,     0x04,     0x00,
/* LFun  */ 0x00,     0x00,     0x00,     0x00,     0x00,     0x00,     0x00,     0x3F,
// Wave 1 
/* LenBr */ 0x39,     0x11,     0xBB,     0x1F,     0x01,     0x01,     0x01,     0x07,
/* Opcode*/ 0x01,     0x01,     0x03,     0x01,     0x00,     0x00,     0x00,     0x00,
/* Output*/ 0x00,     0x02,     0x02,     0x06,     0x06,     0x06,     0x06,     0x00,
/* LFun  */ 0x40,     0x09,     0x0F,     0x09,     0x00,     0x00,     0x00,     0x3F,
// Wave 2 
/* LenBr */ 0x08,     0x10,     0x02,     0x9C,     0x01,     0x3F,     0xBF,     0x07,
/* Opcode*/ 0x01,     0x01,     0x00,     0x03,     0x16,     0x01,     0x01,     0x00,
/* Output*/ 0x00,     0x00,     0x0C,     0x0C,     0x0C,     0x00,     0x00,     0x00,
/* LFun  */ 0xC8,     0xC8,     0x00,     0x00,     0x00,     0x00,     0x00,     0x3F,
// Wave 3 
/* LenBr */ 0x39,     0x01,     0x13,     0x23,     0xA5,     0x2F,     0x3F,     0x07,
/* Opcode*/ 0x01,     0x00,     0x01,     0x03,     0x07,     0x17,     0x01,     0x00,
/* Output*/ 0x00,     0x02,     0x02,     0x02,     0x02,     0x00,     0x00,     0x00,
/* LFun  */ 0x00,     0x00,     0x00,     0x09,     0x36,     0x09,     0x00,     0x3F,
};
// END DO NOT EDIT     
 
// DO NOT EDIT ...                     
const char xdata FlowStates[36] =
{
/* Wave 0 FlowStates */ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
/* Wave 1 FlowStates */ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
/* Wave 2 FlowStates */ 0x83,0x4E,0x04,0x00,0x04,0x03,0x03,0x02,0x00,
/* Wave 3 FlowStates */ 0x84,0x09,0x02,0x02,0x04,0x24,0x03,0x02,0x00,
};
// END DO NOT EDIT     
 
// DO NOT EDIT ...                                               
const char xdata InitData[7] =
{
/* Regs  */ 0xE0,0x00,0x00,0x00,0xEE,0x4E,0x00
};
// END DO NOT EDIT                                               
 
// TO DO: You may add additional code below.
 
void GpifInit( void )
{
  BYTE i;
 
  // Registers which require a synchronization delay, see section 15.14
  // FIFORESET        FIFOPINPOLAR
  // INPKTEND         OUTPKTEND
  // EPxBCH:L         REVCTL
  // GPIFTCB3         GPIFTCB2
  // GPIFTCB1         GPIFTCB0
  // EPxFIFOPFH:L     EPxAUTOINLENH:L
  // EPxFIFOCFG       EPxGPIFFLGSEL
  // PINFLAGSxx       EPxFIFOIRQ
  // EPxFIFOIE        GPIFIRQ
  // GPIFIE           GPIFADRH:L
  // UDMACRCH:L       EPxGPIFTRIG
  // GPIFTRIG
 
  // Note: The pre-REVE EPxGPIFTCH/L register are affected, as well...
  //      ...these have been replaced by GPIFTC[B3:B0] registers
 
  // 8051 doesn't have access to waveform memories 'til
  // the part is in GPIF mode.
 
  IFCONFIG = 0xEE;
  // IFCLKSRC=1   , FIFOs executes on internal clk source
  // xMHz=1       , 48MHz internal clk rate
  // IFCLKOE=0    , Don't drive IFCLK pin signal at 48MHz
  // IFCLKPOL=0   , Don't invert IFCLK pin signal from internal clk
  // ASYNC=1      , master samples asynchronous
  // GSTATE=1     , Drive GPIF states out on PORTE[2:0], debug WF
  // IFCFG[1:0]=10, FX2 in GPIF master mode
 
  GPIFABORT = 0xFF;  // abort any waveforms pending
 
  GPIFREADYCFG = InitData[ 0 ];
  GPIFCTLCFG = InitData[ 1 ];
  GPIFIDLECS = InitData[ 2 ];
  GPIFIDLECTL = InitData[ 3 ];
  GPIFWFSELECT = InitData[ 5 ];
  GPIFREADYSTAT = InitData[ 6 ];
 
  // use dual autopointer feature... 
  AUTOPTRSETUP = 0x07;          // inc both pointers, 
                                // ...warning: this introduces pdata hole(s)
                                // ...at E67B (XAUTODAT1) and E67C (XAUTODAT2)
 
  // source
  AUTOPTRH1 = MSB( &WaveData );
  AUTOPTRL1 = LSB( &WaveData );
 
  // destination
  AUTOPTRH2 = 0xE4;
  AUTOPTRL2 = 0x00;
 
  // transfer
  for ( i = 0x00; i < 128; i++ )
  {
    EXTAUTODAT2 = EXTAUTODAT1;
  }
 
// Configure GPIF Address pins, output initial value,
  PORTCCFG = 0xFF;    // [7:0] as alt. func. GPIFADR[7:0]
  OEC = 0xFF;         // and as outputs
  PORTECFG |= 0x80;   // [8] as alt. func. GPIFADR[8]
  OEE |= 0x80;        // and as output
 
// ...OR... tri-state GPIFADR[8:0] pins
//  PORTCCFG = 0x00;  // [7:0] as port I/O
//  OEC = 0x00;       // and as inputs
//  PORTECFG &= 0x7F; // [8] as port I/O
//  OEE &= 0x7F;      // and as input
 
// GPIF address pins update when GPIFADRH/L written
  SYNCDELAY;                    // 
  GPIFADRH = 0x00;    // bits[7:1] always 0
  SYNCDELAY;                    // 
  GPIFADRL = 0x00;    // point to PERIPHERAL address 0x0000
 
// Configure GPIF FlowStates registers for Wave 0 of WaveData
  FLOWSTATE = FlowStates[ 0 ];
  FLOWLOGIC = FlowStates[ 1 ];
  FLOWEQ0CTL = FlowStates[ 2 ];
  FLOWEQ1CTL = FlowStates[ 3 ];
  FLOWHOLDOFF = FlowStates[ 4 ];
  FLOWSTB = FlowStates[ 5 ];
  FLOWSTBEDGE = FlowStates[ 6 ];
  FLOWSTBHPERIOD = FlowStates[ 7 ];
}
 

Line No.	Rev	Author	Line
1	9	nussgipfel	`// This program configures the General Programmable Interface (GPIF) for FX2.`
2			`// Please do not modify sections of text which are marked as "DO NOT EDIT ...".`
3			`//`
4			`// DO NOT EDIT ...`
5			`// GPIF Initialization`
6			`// Interface Timing Sync`
7			`// Internal Ready Init IntRdy=1`
8			`// CTL Out Tristate-able Binary`
9			`// SingleWrite WF Select 1`
10			`// SingleRead WF Select 0`
11			`// FifoWrite WF Select 3`
12			`// FifoRead WF Select 2`
13			`// Data Bus Idle Drive Tristate`
14			`// END DO NOT EDIT`
15
16			`// DO NOT EDIT ...`
17			`// GPIF Wave Names`
18			`// Wave 0 = Single R`
19			`// Wave 1 = Single W`
20			`// Wave 2 = FIFO Rea`
21			`// Wave 3 = FIFO Wri`
22
23			`// GPIF Ctrl Outputs Level`
24			`// CTL 0 = RDYU CMOS`
25			`// CTL 1 = WRU CMOS`
26			`// CTL 2 = RDYU CMOS`
27	18	nussgipfel	`// CTL 3 = X2U_ex CMOS`
28			`// CTL 4 = U2X_th CMOS`
29	9	nussgipfel	`// CTL 5 = unused CMOS`
30
31			`// GPIF Rdy Inputs`
32			`// RDY0 = WRX`
33			`// RDY1 = RDYX`
34			`// RDY2 = unused`
35			`// RDY3 = unused`
36			`// RDY4 = unused`
37			`// RDY5 = TCXpire`
38			`// FIFOFlag = FIFOFlag`
39			`// IntReady = IntReady`
40			`// END DO NOT EDIT`
41			`// DO NOT EDIT ...`
42			`//`
43			`// GPIF Waveform 0: Single R`
44			`//`
45			`// Interval 0 1 2 3 4 5 6 Idle (7)`
46			`// _________ _________ _________ _________ _________ _________ _________ _________`
47			`//`
48			`// AddrMode Same Val Same Val Same Val Same Val Same Val Same Val Same Val`
49			`// DataMode NO Data NO Data Activate Activate Activate Activate Activate`
50			`// NextData SameData SameData SameData SameData SameData SameData SameData`
51			`// Int Trig No Int No Int No Int No Int No Int No Int No Int`
52			`// IF/Wait IF Wait 1 IF Wait 1 Wait 1 Wait 1 Wait 1`
53			`// Term A WRX WRX`
54			`// LFunc AND AND`
55			`// Term B WRX WRX`
56			`// Branch1 Then 1 ThenIdle`
57			`// Branch0 ElseIdle ElseIdle`
58			`// Re-Exec Yes Yes`
59			`// Sngl/CRC Default Default Default Default Default Default Default`
60			`// RDYU 0 0 0 0 0 0 0 0`
61			`// WRU 0 0 0 0 0 0 0 0`
62			`// RDYU 0 1 1 1 1 1 1 0`
63	18	nussgipfel	`// X2U_ex 0 0 0 0 0 0 0 0`
64			`// U2X_th 0 0 0 0 0 0 0 0`
65	9	nussgipfel	`// unused 0 0 0 0 0 0 0 0`
66			`//`
67			`// END DO NOT EDIT`
68			`// DO NOT EDIT ...`
69			`//`
70			`// GPIF Waveform 1: Single W`
71			`//`
72			`// Interval 0 1 2 3 4 5 6 Idle (7)`
73			`// _________ _________ _________ _________ _________ _________ _________ _________`
74			`//`
75			`// AddrMode Same Val Same Val Same Val Same Val Same Val Same Val Same Val`
76			`// DataMode NO Data NO Data Activate NO Data NO Data NO Data NO Data`
77			`// NextData SameData SameData SameData SameData SameData SameData SameData`
78			`// Int Trig No Int No Int No Int No Int No Int No Int No Int`
79			`// IF/Wait IF IF IF IF Wait 1 Wait 1 Wait 1`
80			`// Term A WRX RDYX RDYX RDYX`
81			`// LFunc OR AND AND AND`
82			`// Term B WRX RDYX IntReady RDYX`
83			`// Branch1 ThenIdle Then 2 ThenIdle Then 3`
84			`// Branch0 Else 1 Else 1 Else 3 ElseIdle`
85			`// Re-Exec No No Yes No`
86			`// Sngl/CRC Default Default Default Default Default Default Default`
87			`// RDYU 0 0 0 0 0 0 0 0`
88			`// WRU 0 1 1 1 1 1 1 0`
89			`// RDYU 0 0 0 1 1 1 1 0`
90	18	nussgipfel	`// X2U_ex 0 0 0 0 0 0 0 0`
91			`// U2X_th 0 0 0 0 0 0 0 0`
92	9	nussgipfel	`// unused 0 0 0 0 0 0 0 0`
93			`//`
94			`// END DO NOT EDIT`
95			`// DO NOT EDIT ...`
96			`//`
97			`// GPIF Waveform 2: FIFO Rea`
98			`//`
99			`// Interval 0 1 2 3 4 5 6 Idle (7)`
100			`// _________ _________ _________ _________ _________ _________ _________ _________`
101			`//`
102			`// AddrMode Same Val Same Val Same Val Same Val Same Val Same Val Same Val`
103			`// DataMode NO Data NO Data NO Data Activate Activate NO Data NO Data`
104			`// NextData SameData SameData SameData SameData NextData SameData SameData`
105			`// Int Trig No Int No Int No Int No Int Trig Int No Int No Int`
106	20	nussgipfel	`// IF/Wait IF IF Wait 2 IF Wait 1 IF IF`
107			`// Term A RDYX RDYX WRX WRX WRX`
108			`// LFunc !A AND B !A AND B AND AND AND`
109			`// Term B WRX WRX WRX WRX WRX`
110			`// Branch1 Then 1 Then 2 Then 3 ThenIdle ThenIdle`
111			`// Branch0 Else 0 Else 0 Else 4 ElseIdle ElseIdle`
112			`// Re-Exec No No Yes No Yes`
113	9	nussgipfel	`// Sngl/CRC Default Default Default Default Default Default Default`
114			`// RDYU 0 0 0 0 0 0 0 0`
115			`// WRU 0 0 0 0 0 0 0 0`
116			`// RDYU 0 0 1 1 1 0 0 0`
117	19	nussgipfel	`// X2U_ex 0 0 1 1 1 0 0 0`
118	18	nussgipfel	`// U2X_th 0 0 0 0 0 0 0 0`
119	9	nussgipfel	`// unused 0 0 0 0 0 0 0 0`
120			`//`
121			`// END DO NOT EDIT`
122			`// DO NOT EDIT ...`
123			`//`
124			`// GPIF Waveform 3: FIFO Wri`
125			`//`
126			`// Interval 0 1 2 3 4 5 6 Idle (7)`
127			`// _________ _________ _________ _________ _________ _________ _________ _________`
128			`//`
129			`// AddrMode Same Val Same Val Same Val Same Val Same Val Same Val Same Val`
130			`// DataMode NO Data NO Data NO Data Activate Activate Activate NO Data`
131	18	nussgipfel	`// NextData SameData SameData SameData SameData NextData NextData SameData`
132	9	nussgipfel	`// Int Trig No Int No Int No Int No Int No Int Trig Int No Int`
133	19	nussgipfel	`// IF/Wait IF Wait 1 IF IF IF IF IF`
134			`// Term A WRX WRX RDYX FIFOFlag RDYX WRX`
135			`// LFunc AND AND AND AND AND AND`
136			`// Term B WRX WRX RDYX FIFOFlag RDYX WRX`
137			`// Branch1 ThenIdle Then 2 Then 4 Then 4 Then 5 ThenIdle`
138			`// Branch0 Else 1 Else 3 Else 3 Else 5 ElseIdle ElseIdle`
139			`// Re-Exec No No No Yes No No`
140	9	nussgipfel	`// Sngl/CRC Default Default Default Default Default Default Default`
141			`// RDYU 0 0 0 0 0 0 0 0`
142			`// WRU 0 1 1 1 1 0 0 0`
143			`// RDYU 0 0 0 0 0 0 0 0`
144	18	nussgipfel	`// X2U_ex 0 0 0 0 0 0 0 0`
145			`// U2X_th 0 0 0 0 0 0 0 0`
146	9	nussgipfel	`// unused 0 0 0 0 0 0 0 0`
147			`//`
148			`// END DO NOT EDIT`
149
150			`// GPIF Program Code`
151
152			`// DO NOT EDIT ...`
153			`#include "fx2.h"`
154			`#include "fx2regs.h"`
155			`#include "fx2sdly.h" // SYNCDELAY macro`
156			`// END DO NOT EDIT`
157
158			`// DO NOT EDIT ...`
159			`const char xdata WaveData[128] =`
160			`{`
161			`// Wave 0`
162			`/* LenBr */ 0x8F, 0x01, 0xBF, 0x01, 0x01, 0x01, 0x01, 0x07,`
163			`/* Opcode*/ 0x01, 0x00, 0x03, 0x02, 0x02, 0x02, 0x02, 0x00,`
164			`/* Output*/ 0x00, 0x04, 0x04, 0x04, 0x04, 0x04, 0x04, 0x00,`
165			`/* LFun */ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,`
166			`// Wave 1`
167			`/* LenBr */ 0x39, 0x11, 0xBB, 0x1F, 0x01, 0x01, 0x01, 0x07,`
168			`/* Opcode*/ 0x01, 0x01, 0x03, 0x01, 0x00, 0x00, 0x00, 0x00,`
169			`/* Output*/ 0x00, 0x02, 0x02, 0x06, 0x06, 0x06, 0x06, 0x00,`
170			`/* LFun */ 0x40, 0x09, 0x0F, 0x09, 0x00, 0x00, 0x00, 0x3F,`
171			`// Wave 2`
172	20	nussgipfel	`/* LenBr */ 0x08, 0x10, 0x02, 0x9C, 0x01, 0x3F, 0xBF, 0x07,`
173	19	nussgipfel	`/* Opcode*/ 0x01, 0x01, 0x00, 0x03, 0x16, 0x01, 0x01, 0x00,`
174			`/* Output*/ 0x00, 0x00, 0x0C, 0x0C, 0x0C, 0x00, 0x00, 0x00,`
175	20	nussgipfel	`/* LFun */ 0xC8, 0xC8, 0x00, 0x00, 0x00, 0x00, 0x00, 0x3F,`
176	9	nussgipfel	`// Wave 3`
177	19	nussgipfel	`/* LenBr */ 0x39, 0x01, 0x13, 0x23, 0xA5, 0x2F, 0x3F, 0x07,`
178			`/* Opcode*/ 0x01, 0x00, 0x01, 0x03, 0x07, 0x17, 0x01, 0x00,`
179	9	nussgipfel	`/* Output*/ 0x00, 0x02, 0x02, 0x02, 0x02, 0x00, 0x00, 0x00,`
180	19	nussgipfel	`/* LFun */ 0x00, 0x00, 0x00, 0x09, 0x36, 0x09, 0x00, 0x3F,`
181	9	nussgipfel	`};`
182			`// END DO NOT EDIT`
183
184			`// DO NOT EDIT ...`
185			`const char xdata FlowStates[36] =`
186			`{`
187			`/* Wave 0 FlowStates */ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,`
188			`/* Wave 1 FlowStates */ 0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,`
189	20	nussgipfel	`/* Wave 2 FlowStates */ 0x83,0x4E,0x04,0x00,0x04,0x03,0x03,0x02,0x00,`
190	19	nussgipfel	`/* Wave 3 FlowStates */ 0x84,0x09,0x02,0x02,0x04,0x24,0x03,0x02,0x00,`
191	9	nussgipfel	`};`
192			`// END DO NOT EDIT`
193
194			`// DO NOT EDIT ...`
195			`const char xdata InitData[7] =`
196			`{`
197			`/* Regs */ 0xE0,0x00,0x00,0x00,0xEE,0x4E,0x00`
198			`};`
199			`// END DO NOT EDIT`
200
201			`// TO DO: You may add additional code below.`
202
203			`void GpifInit( void )`
204			`{`
205			`BYTE i;`
206
207			`// Registers which require a synchronization delay, see section 15.14`
208			`// FIFORESET FIFOPINPOLAR`
209			`// INPKTEND OUTPKTEND`
210			`// EPxBCH:L REVCTL`
211			`// GPIFTCB3 GPIFTCB2`
212			`// GPIFTCB1 GPIFTCB0`
213			`// EPxFIFOPFH:L EPxAUTOINLENH:L`
214			`// EPxFIFOCFG EPxGPIFFLGSEL`
215			`// PINFLAGSxx EPxFIFOIRQ`
216			`// EPxFIFOIE GPIFIRQ`
217			`// GPIFIE GPIFADRH:L`
218			`// UDMACRCH:L EPxGPIFTRIG`
219			`// GPIFTRIG`
220
221			`// Note: The pre-REVE EPxGPIFTCH/L register are affected, as well...`
222			`// ...these have been replaced by GPIFTC[B3:B0] registers`
223
224			`// 8051 doesn't have access to waveform memories 'til`
225			`// the part is in GPIF mode.`
226
227			`IFCONFIG = 0xEE;`
228			`// IFCLKSRC=1 , FIFOs executes on internal clk source`
229			`// xMHz=1 , 48MHz internal clk rate`
230			`// IFCLKOE=0 , Don't drive IFCLK pin signal at 48MHz`
231			`// IFCLKPOL=0 , Don't invert IFCLK pin signal from internal clk`
232			`// ASYNC=1 , master samples asynchronous`
233			`// GSTATE=1 , Drive GPIF states out on PORTE[2:0], debug WF`
234			`// IFCFG[1:0]=10, FX2 in GPIF master mode`
235
236			`GPIFABORT = 0xFF; // abort any waveforms pending`
237
238			`GPIFREADYCFG = InitData[ 0 ];`
239			`GPIFCTLCFG = InitData[ 1 ];`
240			`GPIFIDLECS = InitData[ 2 ];`
241			`GPIFIDLECTL = InitData[ 3 ];`
242			`GPIFWFSELECT = InitData[ 5 ];`
243			`GPIFREADYSTAT = InitData[ 6 ];`
244
245			`// use dual autopointer feature...`
246			`AUTOPTRSETUP = 0x07; // inc both pointers,`
247			`// ...warning: this introduces pdata hole(s)`
248			`// ...at E67B (XAUTODAT1) and E67C (XAUTODAT2)`
249
250			`// source`
251			`AUTOPTRH1 = MSB( &WaveData );`
252			`AUTOPTRL1 = LSB( &WaveData );`
253
254			`// destination`
255			`AUTOPTRH2 = 0xE4;`
256			`AUTOPTRL2 = 0x00;`
257
258			`// transfer`
259			`for ( i = 0x00; i < 128; i++ )`
260			`{`
261			`EXTAUTODAT2 = EXTAUTODAT1;`
262			`}`
263
264			`// Configure GPIF Address pins, output initial value,`
265			`PORTCCFG = 0xFF; // [7:0] as alt. func. GPIFADR[7:0]`
266			`OEC = 0xFF; // and as outputs`
267			`PORTECFG \|= 0x80; // [8] as alt. func. GPIFADR[8]`
268			`OEE \|= 0x80; // and as output`
269
270			`// ...OR... tri-state GPIFADR[8:0] pins`
271			`// PORTCCFG = 0x00; // [7:0] as port I/O`
272			`// OEC = 0x00; // and as inputs`
273			`// PORTECFG &= 0x7F; // [8] as port I/O`
274			`// OEE &= 0x7F; // and as input`
275
276			`// GPIF address pins update when GPIFADRH/L written`
277			`SYNCDELAY; //`
278			`GPIFADRH = 0x00; // bits[7:1] always 0`
279			`SYNCDELAY; //`
280			`GPIFADRL = 0x00; // point to PERIPHERAL address 0x0000`
281
282			`// Configure GPIF FlowStates registers for Wave 0 of WaveData`
283			`FLOWSTATE = FlowStates[ 0 ];`
284			`FLOWLOGIC = FlowStates[ 1 ];`
285			`FLOWEQ0CTL = FlowStates[ 2 ];`
286			`FLOWEQ1CTL = FlowStates[ 3 ];`
287			`FLOWHOLDOFF = FlowStates[ 4 ];`
288			`FLOWSTB = FlowStates[ 5 ];`
289			`FLOWSTBEDGE = FlowStates[ 6 ];`
290			`FLOWSTBHPERIOD = FlowStates[ 7 ];`
291			`}`
292

Browse

Tools

Subversion Repositories gecko3

[/] [gecko3/] [trunk/] [GECKO3COM/] [gecko3com-fw/] [firmware/] [gpif-design/] [gecko3main_gpif.c] - Blame information for rev 20