URL https://opencores.org/ocsvn/ion/ion/trunk

Subversion Repositories ion

[/] [ion/] [trunk/] [src/] [memtest/] [memtest.s] - Blame information for rev 249

Go to most recent revision | Details | Compare with Previous | View Log


################################################################################
# memtest.s -- Test external RAM memory (XRAM)
#-------------------------------------------------------------------------------
# This program tests the external RAM (connected to the core through the cache
# module). Currently it only finds the RAM top address if given the bottom
# address. Subsequent versions will add some minimal diagnostic capability,
# which will be needed when DRAM access is implemented.
#
# This program does only support a single continuous chunk of RAM. If the cache
# module ever supports more than one chunk (e.g. DRAM and SRAM as in the DE-1
# board) this program will be modified accordingly.
#
# The program assumes there's no useable r/w memory other than the XRAM so it
# does not use any memory for variables or stack.
#-------------------------------------------------------------------------------
#
#
#-------------------------------------------------------------------------------
# To be run from reset vector, standalone. Interrupts must be disabled.
#
################################################################################
 
    #---- Test parameters
    .ifndef XRAM_MAX
    .set XRAM_MAX,      1024                # max. no. of KB to test for
    .endif
    .ifndef XRAM_BASE
    .set XRAM_BASE,     0x00000000          # 1st XRAM address
    .endif
 
 
    #---- Set to >0 to enable a few debug messages
    .set DEBUG,         0
 
    #---- Cache parameters
    .set ICACHE_NUM_LINES, 256              # no. of lines in the I-Cache
    .set DCACHE_NUM_LINES, 256              # no. of lines in the D-Cache
    .set DCACHE_LINE_SIZE, 4                # D-Cache line size in words
 
 
    #---- UART stuff
    .set UART_BASE,     0x20000000          # UART base address
    .set UART_TX,       0x0000              # TX reg offset
    .set UART_STATUS,   0x0004              # status reg offset
    .set UART_TX_RDY,   0x0001              # tx ready flag mask
 
    #---- Debug register block -- 4 read-write, 32-bit registers
    .set DEBUG_BASE,    0x20010020          # Debug block base
 
    #---------------------------------------------------------------------------
 
    .text
    .align  2
    .globl  entry
    .ent    entry
entry:
    .set    noreorder
 
    b       start_test
    nop
 
    .ifgt   0
    #--- Trap handler address: we don't expect any traps -----------------------
    .org    0x0180
interrupt_vector:
    b       interrupt_vector    # just freeze there
    nop
    .endif
 
#-------------------------------------------------------------------------------
 
start_test:
    li      $a0,0x00000002
    mtc0    $a0,$12             # disable interrupts and cache
 
    .ifdef  TEST_CACHE          # if we're going to test the caches then
    jal     init_cache          # invalidate all the I- and D-Cache lines now
    nop
    jal     test_dcache
    nop
    .endif
 
    la      $a0,msg0
    jal     puts
    nop
    li      $a0,XRAM_BASE
    li      $a1,8
    jal     put_hex
    nop
    la      $a0,crlf
    jal     puts
    nop
 
    la      $t0,XRAM_BASE+4     # address of memory word being tested
    li      $t2,XRAM_MAX        # max amount of KBs to test for
    li      $t3,1               # (used to decrement $t2)
    li      $t4,0               # no. of KBs found
    move    $t5,$t0             # keep the start addr at hand for comparison
 
    sw      $zero,0($t0)        # clear 1st test word (in case of prev. run)
 
test_loop:
    lw      $t1,0($t0)          # read word contents
    beq     $t5,$t1,hit_mirror  # if it's the start address, we hit a mirror
    nop                         # we rolled off the end of the RAM back here
    sw      $t0,0($t0)          # word = word address
    lw      $t1,0($t0)          # read word back...
    bne     $t1,$t0,bad_word    # ...and if no match, we run off the RAM
    nop                         #
    sub     $t2,$t2,$t3         # decrement loop counter...
    bnez    $t2,test_loop       # ...and go back if there's more to go
    addiu   $t0,0x400           # in any case, increment test address by 1KB
 
    b       end_test            # end of memory found, result is in $t4
    nop
 
hit_mirror:                     # memory mirror detected
    .ifgt   DEBUG
    la      $a0,msg_mirror
    jal     puts
    nop
    .endif
    b       end_test
    nop
 
bad_word:                       # readback error detected (maybe r/o area?)
    .ifgt   DEBUG
    la      $a0,msg_bad
    jal     puts
    nop
    .endif
    b       end_test
    nop
 
end_test:                       # test done, ramtop+4 in $t0, #KB in $t4
 
 
    la      $a0,msg1            # Print ramtop message...
    jal     puts
    nop
 
    addi    $a0,$t0,-4          # substract the +4 offset we added before
    move    $sp,$t0             # init SP at the top of RAM space
    addi    $sp,$sp,-16
    li      $a1,8
    jal     put_hex
    nop
    la      $a0,crlf
    jal     puts
    nop
 
    # Clear RAM (only first words, so that simulation is not eternal)
    .ifgt 1
    li      $a0,XRAM_BASE
    addi    $a1,$a0,80*4
clear_xram_loop:
    sw      $zero,0($a0)
    blt     $a0,$a1,clear_xram_loop
    addi    $a0,$a0,4
    .endif
 
    # Test code execution from SRAM. We copy the test_exec_sram routine to
    # the base of the SRAM and then jal to it
    li      $a1,64
    li      $a0,XRAM_BASE
    la      $a3,test_exec_sram
copy_to_sram:
    lw      $a2,0($a3)
    nop
    sw      $a2,0($a0)
    addi    $a1,$a1,-4
    addi    $a3,$a3,4
    bnez    $a1,copy_to_sram
    addi    $a0,$a0,4
 
    # Optionally dump first few words of XRAM and jump onto XRAM
    .ifgt 1
    la      $a0,msg5
    jal     puts
    nop
    li      $a0,XRAM_BASE
    jal     dump_hex
    ori     $a1,$zero,20
    .endif
 
    .ifgt   1
    li      $a0,XRAM_BASE
    nop
    jalr    $a0
    nop
    .endif
 
    # If all went well in the SRAM we'll have returned here
    .ifgt   0
    # FIXME now we should do some strong test on the RAM to see if it's wired
    # correctly, using the right timing, etc.
 
    # Ok, now we know we have some RAM and stack space we can do some further
    # testing.
    # dump the first few words of FLASH
 
    la      $a0,msg2
    jal     puts
    nop
 
    # FIXME flash base address is hardcoded
    li      $a0,0xb0000000
    jal     put_hex
    ori     $a1,$zero,8
 
    la      $a0,crlf
    jal     puts
    nop
 
    la      $a0,crlf
    jal     puts
    nop
 
    li      $a0,0xb0000000
    jal     dump_hex
    ori     $a1,$zero,6
    .endif
 
 
    # Optionally jump to FLASH. This is only useful in simulation.
    .ifgt 1
    .ifdef  EXEC_FLASH
    la      $a0,msg8
    jal     puts
    nop
    li      $a0,0xb0000000
    nop
    jalr    $a0
    nop
    .endif
    .endif
 
    la      $a0,msg4
    jal     puts
    nop
 
 
$DONE:
    j       $DONE               # ...and freeze here
    nop
 
test_dcache:
    # This D-Cache test is extremely simplistic:
    # We'll make a few I/O writes to a block of test registers and then readback
    # all the data. The writes and reads will be done as fast as the CPU can,
    # i.e. back to back. We rely on the I-Cache being active for this.
    # Note that, while the CPU 'wants' to do the WR cycles back to back, it
    # can't because of the D-Cache stalls. That's the interaction we want to
    # test here, for both WR and RD cycles.
 
    move    $t8,$ra             # Save $ra -- remember, there's no stack
    la      $a0,msg9            # Display 'testing cache' message
    jal     puts
    nop
    li      $a0,DEBUG_BASE      # We'll use the debug register block as the
    li      $a1,0x112200aa      # target of a series of RD and WR cycles.
    addi    $a2,$a1,0x100       # Load $a1..$a2 with dummy data.
    addi    $a3,$a2,0x100
    .align  4                   # Align to 16 bytes (start of I-Cache line)
    sw      $a1,0x0($a0)        # Perform 3 WR cycles...
    sw      $a2,0x4($a0)
    sw      $a3,0x8($a0)
 
    lw      $t0,0x0($a0)        # ...followed by a RD cycle
    bne     $a1,$t0,test_dcache_ww_error
    nop
    lw      $t0,0x4($a0)        # Verify the other 2 WR cycles
    bne     $a2,$t0,test_dcache_ww_error
    nop
    lw      $t0,0x8($a0)
    bne     $a3,$t0,test_dcache_ww_error
    nop
 
    la      $a0,msg11           # display OK message...
    jal     puts
    nop
 
test_dcache_done:               # ...and quit.
    move    $ra,$t8             # Recover $ra and return
    jr      $ra
    nop
 
test_dcache_ww_error:           # We'll print the same error for all kinds of
    la      $a0,msg10           # failure; we'll diagnose it in simulation.
test_dcache_error:
    jal     puts
    nop
    b       test_dcache_done
 
 
    # This short routine will be copied to RAM and then executed there. This
    # will test the behavior of the I-Cache.
test_exec_sram:
    #jr      $ra
    #nop
    sw      $ra,0($sp)
    addi    $sp,$sp,-4
    la      $a0,msg3
    la      $a1,puts
    jalr    $a1
    nop
    lw      $ra,4($sp)
    jr      $ra
    addi    $sp,$sp,4
test_exec_sram_end:
    nop
 
 
 
#---- Functions ----------------------------------------------------------------
 
# void dump_hex(int *address {a0}, int len {a1})
dump_hex:
    move    $t7,$a0
    move    $t6,$a1
    sw      $ra,0($sp)
    addi    $sp,$sp,-4
 
dump_hex_loop_lines:
    move    $a0,$t7
    li      $a1,8
    jal     put_hex
    nop
    la      $a0,msg6
    jal     puts
    nop
    li      $t9,4
 
dump_hex_loop_words:
    lw      $a0,0($t7)
    jal     put_hex
    li      $a1,8
 
    la      $a0,space
    jal     puts
    addi    $t7,4
 
    addi    $t9,$t9,-1
    bnez    $t9,dump_hex_loop_words
    nop
 
    la      $a0,crlf
    jal     puts
    nop
 
    addi    $t6,$t6,-1
    bnez    $t6,dump_hex_loop_lines
    nop
 
    la      $a0,msg7
    jal     puts
    addi    $t7,4
 
    # Some debug hex dump...
    .ifgt 0
    lw      $ra,4($sp)
    move    $a0,$ra
    li      $a1,8
    jal     put_hex
    nop
stop_here:
    j       stop_here
    nop
    .endif
 
    nop
    lw      $ra,4($sp)
    jr      $ra
    addi    $sp,$sp,4
 
 
#---- Cache-related functions --------------------------------------------------
 
# void init_cache(void) -- invalidates all I-Cache lines (uses no RAM)
init_cache:
    li      $a0,0x00010000      # Disable cache, enable I-cache line invalidation
    mfc0    $a1,$12
    or      $a0,$a0,$a1
    mtc0    $a0,$12
 
    # In order to invalidate a I-Cache line we have to write its tag number to
    # any address while bits CP0[12].17:16=01. The write will be executed as a
    # regular write too, as a side effect, so we need to choose a harmless
    # target address.
 
    li      $a0,XRAM_BASE
    li      $a2,0
    li      $a1,ICACHE_NUM_LINES-1
 
inv_i_cache_loop:
    sw      $a2,0($a0)
    blt     $a2,$a1,inv_i_cache_loop
    addi    $a2,1
 
    # Now, the D-Cache is different. To invalidate a D-Cache line you just
    # read from it (by proper selection of a dummy target address)  while bits
    # CP0[12].17:16=01. The data read is undefined and should be discarded.
 
    li      $a0,0               # Use any base address that is mapped
    li      $a2,0
    li      $a1,DCACHE_NUM_LINES-1
 
inv_d_cache_loop:
    lw      $zero,0($a0)
    addi    $a0,DCACHE_LINE_SIZE*4
    blt     $a2,$a1,inv_d_cache_loop
    addi    $a2,1
 
    lui     $a1,0x0002          # Leave with cache enabled
    mfc0    $a0,$12
    andi    $a0,$a0,0xffff
    or      $a1,$a0,$a1
    jr      $ra
    mtc0    $a1,$12
 
 
 
#--- Special functions that do not use any RAM ---------------------------------
# WARNING: Not for general use!
# All parameters in $a0..$a4, stack unused. No attempt to comply with any ABI
# has been made.
# Since we can't use any RAM, registers have been used with no regard for
# intended usage -- have to share reg bank with calling function.
 
# void puts(char *s) -- print zero-terminated string
puts:
    la      $a2,UART_BASE       # UART base address
puts_loop:
    lb      $v0,0($a0)
    beqz    $v0,puts_end
    addiu   $a0,1
puts_wait_tx_rdy:
    lw      $v1,UART_STATUS($a2)
    andi    $v1,$v1,UART_TX_RDY
    beqz    $v1,puts_wait_tx_rdy
    nop
    sw      $v0,UART_TX($a2)
    b       puts_loop
    nop
 
puts_end:
    jr      $ra
    nop
 
# void put_hex(int n, int d) -- print integer as d-digit hex
put_hex:
    la      $a2,UART_BASE
    la      $a3,put_hex_table
    addi    $a1,-1
    add     $a1,$a1,$a1
    add     $a1,$a1,$a1
 
put_hex_loop:
    srlv    $v0,$a0,$a1
    andi    $v0,$v0,0x0f
    addu    $s2,$a3,$v0
    lb      $v0,0($s2)
put_hex_wait_tx_rdy:
    lw      $v1,UART_STATUS($a2)
    andi    $v1,$v1,UART_TX_RDY
    beqz    $v1,put_hex_wait_tx_rdy
    nop
    sw      $v0,UART_TX($a2)
 
    bnez    $a1,put_hex_loop
    addi    $a1,-4
 
    jr      $ra
    nop
 
 
#---- Constant data (note we keep it in the text section) ----------------------
 
put_hex_table:
    .ascii  "0123456789abcdef"
 
msg0:
    .ascii  "\n\r"
    .asciz  "Scanning external memory at 0x"
msg1:
    .asciz  "Found XRAM top at           0x"
crlf:
    .asciz "\n\r"
space:
    .asciz "  "
msg_mirror:
    .asciz "hit mirror!\n\r"
msg_bad:
    .asciz "bad readback!\n\r"
msg2:
    .asciz "\n\rDumping the first few words of FLASH at address 0x"
msg3:
    .ascii "\n\rTesting code execution from SRAM...  "
    .asciz "if you see this, it worked\n\r"
msg4:
    .ascii  "\n\r\n\r"
    .asciz  "End of test.\n\r\n\r"
msg5:
    .asciz  "Dump of first few words of XRAM after initialization:\n\r"
msg6:
    .asciiz ": "
msg7:
    .asciiz "<end of dump>"
msg8:
    .ascii  "\n\r"
    .asciz  "Testing execution from 8-bit static memory (FLASH)\n\r"
msg9:
    .asciz  "Testing D-Cache with back-to-back pairs of RD & WR cycles...\n\r"
msg10:
    .asciz  "Error in WR+WR sequence\n\r"
msg11:
    .asciz  "OK\n\r"
 
 
    .set    reorder
    .end    entry
 

Line No.	Rev	Author	Line
1	50	ja_rd	`################################################################################`
2			`# memtest.s -- Test external RAM memory (XRAM)`
3			`#-------------------------------------------------------------------------------`
4			`# This program tests the external RAM (connected to the core through the cache`
5	109	ja_rd	`# module). Currently it only finds the RAM top address if given the bottom`
6	50	ja_rd	`# address. Subsequent versions will add some minimal diagnostic capability,`
7			`# which will be needed when DRAM access is implemented.`
8			`#`
9			`# This program does only support a single continuous chunk of RAM. If the cache`
10	109	ja_rd	`# module ever supports more than one chunk (e.g. DRAM and SRAM as in the DE-1`
11	50	ja_rd	`# board) this program will be modified accordingly.`
12	109	ja_rd	`#`
13	50	ja_rd	`# The program assumes there's no useable r/w memory other than the XRAM so it`
14			`# does not use any memory for variables or stack.`
15	109	ja_rd	`#-------------------------------------------------------------------------------`
16	50	ja_rd	`#`
17	109	ja_rd	`#`
18			`#-------------------------------------------------------------------------------`
19	50	ja_rd	`# To be run from reset vector, standalone. Interrupts must be disabled.`
20			`#`
21			`################################################################################`
22
23	109	ja_rd	`#---- Test parameters`
24			`.ifndef XRAM_MAX`
25			`.set XRAM_MAX, 1024 # max. no. of KB to test for`
26			`.endif`
27			`.ifndef XRAM_BASE`
28			`.set XRAM_BASE, 0x00000000 # 1st XRAM address`
29			`.endif`
30
31
32	50	ja_rd	`#---- Set to >0 to enable a few debug messages`
33			`.set DEBUG, 0`
34
35	109	ja_rd	`#---- Cache parameters`
36			`.set ICACHE_NUM_LINES, 256 # no. of lines in the I-Cache`
37			`.set DCACHE_NUM_LINES, 256 # no. of lines in the D-Cache`
38			`.set DCACHE_LINE_SIZE, 4 # D-Cache line size in words`
39	50	ja_rd
40	109	ja_rd
41			`#---- UART stuff`
42	50	ja_rd	`.set UART_BASE, 0x20000000 # UART base address`
43			`.set UART_TX, 0x0000 # TX reg offset`
44	229	ja_rd	`.set UART_STATUS, 0x0004 # status reg offset`
45			`.set UART_TX_RDY, 0x0001 # tx ready flag mask`
46	50	ja_rd
47	213	ja_rd	`#---- Debug register block -- 4 read-write, 32-bit registers`
48	229	ja_rd	`.set DEBUG_BASE, 0x20010020 # Debug block base`
49	213	ja_rd
50	50	ja_rd	`#---------------------------------------------------------------------------`
51
52			`.text`
53			`.align 2`
54			`.globl entry`
55			`.ent entry`
56			`entry:`
57			`.set noreorder`
58
59			`b start_test`
60			`nop`
61
62	66	ja_rd	`.ifgt 0`
63	50	ja_rd	`#--- Trap handler address: we don't expect any traps -----------------------`
64	66	ja_rd	`.org 0x0180`
65	50	ja_rd	`interrupt_vector:`
66	109	ja_rd	`b interrupt_vector # just freeze there`
67	50	ja_rd	`nop`
68	66	ja_rd	`.endif`
69	109	ja_rd
70	50	ja_rd	`#-------------------------------------------------------------------------------`
71
72	109	ja_rd	`start_test:`
73	152	ja_rd	`li $a0,0x00000002`
74			`mtc0 $a0,$12 # disable interrupts and cache`
75	109	ja_rd
76	213	ja_rd	`.ifdef TEST_CACHE # if we're going to test the caches then`
77			`jal init_cache # invalidate all the I- and D-Cache lines now`
78	109	ja_rd	`nop`
79	213	ja_rd	`jal test_dcache`
80			`nop`
81	109	ja_rd	`.endif`
82
83	50	ja_rd	`la $a0,msg0`
84			`jal puts`
85			`nop`
86			`li $a0,XRAM_BASE`
87			`li $a1,8`
88			`jal put_hex`
89			`nop`
90			`la $a0,crlf`
91			`jal puts`
92			`nop`
93	109	ja_rd
94	66	ja_rd	`la $t0,XRAM_BASE+4 # address of memory word being tested`
95	50	ja_rd	`li $t2,XRAM_MAX # max amount of KBs to test for`
96			`li $t3,1 # (used to decrement $t2)`
97			`li $t4,0 # no. of KBs found`
98			`move $t5,$t0 # keep the start addr at hand for comparison`
99	109	ja_rd
100	50	ja_rd	`sw $zero,0($t0) # clear 1st test word (in case of prev. run)`
101	109	ja_rd
102	50	ja_rd	`test_loop:`
103			`lw $t1,0($t0) # read word contents`
104			`beq $t5,$t1,hit_mirror # if it's the start address, we hit a mirror`
105			`nop # we rolled off the end of the RAM back here`
106			`sw $t0,0($t0) # word = word address`
107			`lw $t1,0($t0) # read word back...`
108			`bne $t1,$t0,bad_word # ...and if no match, we run off the RAM`
109	109	ja_rd	`nop #`
110	50	ja_rd	`sub $t2,$t2,$t3 # decrement loop counter...`
111			`bnez $t2,test_loop # ...and go back if there's more to go`
112			`addiu $t0,0x400 # in any case, increment test address by 1KB`
113	109	ja_rd
114	50	ja_rd	`b end_test # end of memory found, result is in $t4`
115			`nop`
116	109	ja_rd
117	50	ja_rd	`hit_mirror: # memory mirror detected`
118			`.ifgt DEBUG`
119			`la $a0,msg_mirror`
120			`jal puts`
121			`nop`
122			`.endif`
123			`b end_test`
124			`nop`
125	109	ja_rd
126	50	ja_rd	`bad_word: # readback error detected (maybe r/o area?)`
127			`.ifgt DEBUG`
128			`la $a0,msg_bad`
129			`jal puts`
130			`nop`
131			`.endif`
132			`b end_test`
133			`nop`
134
135	78	ja_rd	`end_test: # test done, ramtop+4 in $t0, #KB in $t4`
136
137	109	ja_rd
138	50	ja_rd	`la $a0,msg1 # Print ramtop message...`
139			`jal puts`
140			`nop`
141	109	ja_rd
142	66	ja_rd	`addi $a0,$t0,-4 # substract the +4 offset we added before`
143	78	ja_rd	`move $sp,$t0 # init SP at the top of RAM space`
144	90	ja_rd	`addi $sp,$sp,-16`
145	50	ja_rd	`li $a1,8`
146			`jal put_hex`
147			`nop`
148			`la $a0,crlf`
149			`jal puts`
150			`nop`
151	109	ja_rd
152			`# Clear RAM (only first words, so that simulation is not eternal)`
153			`.ifgt 1`
154			`li $a0,XRAM_BASE`
155			`addi $a1,$a0,80*4`
156			`clear_xram_loop:`
157			`sw $zero,0($a0)`
158			`blt $a0,$a1,clear_xram_loop`
159			`addi $a0,$a0,4`
160			`.endif`
161
162			`# Test code execution from SRAM. We copy the test_exec_sram routine to`
163	90	ja_rd	`# the base of the SRAM and then jal to it`
164			`li $a1,64`
165			`li $a0,XRAM_BASE`
166			`la $a3,test_exec_sram`
167			`copy_to_sram:`
168			`lw $a2,0($a3)`
169			`nop`
170			`sw $a2,0($a0)`
171			`addi $a1,$a1,-4`
172			`addi $a3,$a3,4`
173			`bnez $a1,copy_to_sram`
174			`addi $a0,$a0,4`
175	109	ja_rd
176			`# Optionally dump first few words of XRAM and jump onto XRAM`
177			`.ifgt 1`
178			`la $a0,msg5`
179			`jal puts`
180			`nop`
181			`li $a0,XRAM_BASE`
182	90	ja_rd	`jal dump_hex`
183	109	ja_rd	`ori $a1,$zero,20`
184	90	ja_rd	`.endif`
185	109	ja_rd
186			`.ifgt 1`
187	90	ja_rd	`li $a0,XRAM_BASE`
188	109	ja_rd	`nop`
189	90	ja_rd	`jalr $a0`
190			`nop`
191	109	ja_rd	`.endif`
192
193			`# If all went well in the SRAM we'll have returned here`
194	90	ja_rd	`.ifgt 0`
195	109	ja_rd	`# FIXME now we should do some strong test on the RAM to see if it's wired`
196	78	ja_rd	`# correctly, using the right timing, etc.`
197	109	ja_rd
198	78	ja_rd	`# Ok, now we know we have some RAM and stack space we can do some further`
199			`# testing.`
200			`# dump the first few words of FLASH`
201	109	ja_rd
202	78	ja_rd	`la $a0,msg2`
203			`jal puts`
204			`nop`
205	109	ja_rd
206	78	ja_rd	`# FIXME flash base address is hardcoded`
207			`li $a0,0xb0000000`
208			`jal put_hex`
209			`ori $a1,$zero,8`
210	109	ja_rd
211	78	ja_rd	`la $a0,crlf`
212			`jal puts`
213			`nop`
214
215			`la $a0,crlf`
216			`jal puts`
217			`nop`
218	109	ja_rd
219	78	ja_rd	`li $a0,0xb0000000`
220			`jal dump_hex`
221	109	ja_rd	`ori $a1,$zero,6`
222	90	ja_rd	`.endif`
223	109	ja_rd
224
225			`# Optionally jump to FLASH. This is only useful in simulation.`
226			`.ifgt 1`
227			`.ifdef EXEC_FLASH`
228			`la $a0,msg8`
229			`jal puts`
230			`nop`
231			`li $a0,0xb0000000`
232			`nop`
233			`jalr $a0`
234			`nop`
235			`.endif`
236			`.endif`
237
238			`la $a0,msg4`
239			`jal puts`
240			`nop`
241
242
243	50	ja_rd	`$DONE:`
244			`j $DONE # ...and freeze here`
245			`nop`
246
247	213	ja_rd	`test_dcache:`
248			`# This D-Cache test is extremely simplistic:`
249			`# We'll make a few I/O writes to a block of test registers and then readback`
250			`# all the data. The writes and reads will be done as fast as the CPU can,`
251			`# i.e. back to back. We rely on the I-Cache being active for this.`
252			`# Note that, while the CPU 'wants' to do the WR cycles back to back, it`
253			`# can't because of the D-Cache stalls. That's the interaction we want to`
254			`# test here, for both WR and RD cycles.`
255	50	ja_rd
256	213	ja_rd	`move $t8,$ra # Save $ra -- remember, there's no stack`
257			`la $a0,msg9 # Display 'testing cache' message`
258			`jal puts`
259			`nop`
260			`li $a0,DEBUG_BASE # We'll use the debug register block as the`
261			`li $a1,0x112200aa # target of a series of RD and WR cycles.`
262			`addi $a2,$a1,0x100 # Load $a1..$a2 with dummy data.`
263			`addi $a3,$a2,0x100`
264			`.align 4 # Align to 16 bytes (start of I-Cache line)`
265			`sw $a1,0x0($a0) # Perform 3 WR cycles...`
266			`sw $a2,0x4($a0)`
267			`sw $a3,0x8($a0)`
268
269			`lw $t0,0x0($a0) # ...followed by a RD cycle`
270			`bne $a1,$t0,test_dcache_ww_error`
271			`nop`
272			`lw $t0,0x4($a0) # Verify the other 2 WR cycles`
273			`bne $a2,$t0,test_dcache_ww_error`
274			`nop`
275			`lw $t0,0x8($a0)`
276			`bne $a3,$t0,test_dcache_ww_error`
277			`nop`
278
279			`la $a0,msg11 # display OK message...`
280			`jal puts`
281			`nop`
282
283			`test_dcache_done: # ...and quit.`
284			`move $ra,$t8 # Recover $ra and return`
285			`jr $ra`
286			`nop`
287
288			`test_dcache_ww_error: # We'll print the same error for all kinds of`
289			`la $a0,msg10 # failure; we'll diagnose it in simulation.`
290			`test_dcache_error:`
291			`jal puts`
292			`nop`
293			`b test_dcache_done`
294
295
296	109	ja_rd	`# This short routine will be copied to RAM and then executed there. This`
297			`# will test the behavior of the I-Cache.`
298	90	ja_rd	`test_exec_sram:`
299			`#jr $ra`
300			`#nop`
301			`sw $ra,0($sp)`
302			`addi $sp,$sp,-4`
303			`la $a0,msg3`
304			`la $a1,puts`
305			`jalr $a1`
306			`nop`
307			`lw $ra,4($sp)`
308			`jr $ra`
309			`addi $sp,$sp,4`
310			`test_exec_sram_end:`
311	109	ja_rd	`nop`
312	90	ja_rd
313
314
315	50	ja_rd	`#---- Functions ----------------------------------------------------------------`
316	78	ja_rd
317	109	ja_rd	`# void dump_hex(int *address {a0}, int len {a1})`
318	78	ja_rd	`dump_hex:`
319			`move $t7,$a0`
320	109	ja_rd	`move $t6,$a1`
321	78	ja_rd	`sw $ra,0($sp)`
322			`addi $sp,$sp,-4`
323	109	ja_rd
324			`dump_hex_loop_lines:`
325			`move $a0,$t7`
326			`li $a1,8`
327			`jal put_hex`
328			`nop`
329			`la $a0,msg6`
330			`jal puts`
331			`nop`
332			`li $t9,4`
333
334			`dump_hex_loop_words:`
335	78	ja_rd	`lw $a0,0($t7)`
336			`jal put_hex`
337			`li $a1,8`
338	109	ja_rd
339	78	ja_rd	`la $a0,space`
340			`jal puts`
341			`addi $t7,4`
342	109	ja_rd
343			`addi $t9,$t9,-1`
344			`bnez $t9,dump_hex_loop_words`
345	78	ja_rd	`nop`
346	109	ja_rd
347			`la $a0,crlf`
348			`jal puts`
349			`nop`
350
351			`addi $t6,$t6,-1`
352			`bnez $t6,dump_hex_loop_lines`
353			`nop`
354
355			`la $a0,msg7`
356			`jal puts`
357			`addi $t7,4`
358
359	213	ja_rd	`# Some debug hex dump...`
360	109	ja_rd	`.ifgt 0`
361	78	ja_rd	`lw $ra,4($sp)`
362	109	ja_rd	`move $a0,$ra`
363			`li $a1,8`
364			`jal put_hex`
365			`nop`
366	213	ja_rd	`stop_here:`
367			`j stop_here`
368	109	ja_rd	`nop`
369			`.endif`
370
371			`nop`
372			`lw $ra,4($sp)`
373	78	ja_rd	`jr $ra`
374			`addi $sp,$sp,4`
375
376
377	109	ja_rd	`#---- Cache-related functions --------------------------------------------------`
378
379			`# void init_cache(void) -- invalidates all I-Cache lines (uses no RAM)`
380			`init_cache:`
381			`li $a0,0x00010000 # Disable cache, enable I-cache line invalidation`
382	152	ja_rd	`mfc0 $a1,$12`
383			`or $a0,$a0,$a1`
384	109	ja_rd	`mtc0 $a0,$12`
385
386			`# In order to invalidate a I-Cache line we have to write its tag number to`
387			`# any address while bits CP0[12].17:16=01. The write will be executed as a`
388			`# regular write too, as a side effect, so we need to choose a harmless`
389			`# target address.`
390
391			`li $a0,XRAM_BASE`
392			`li $a2,0`
393			`li $a1,ICACHE_NUM_LINES-1`
394
395			`inv_i_cache_loop:`
396			`sw $a2,0($a0)`
397			`blt $a2,$a1,inv_i_cache_loop`
398			`addi $a2,1`
399
400	229	ja_rd	`# Now, the D-Cache is different. To invalidate a D-Cache line you just`
401			`# read from it (by proper selection of a dummy target address) while bits`
402			`# CP0[12].17:16=01. The data read is undefined and should be discarded.`
403
404			`li $a0,0 # Use any base address that is mapped`
405			`li $a2,0`
406			`li $a1,DCACHE_NUM_LINES-1`
407
408			`inv_d_cache_loop:`
409			`lw $zero,0($a0)`
410			`addi $a0,DCACHE_LINE_SIZE*4`
411			`blt $a2,$a1,inv_d_cache_loop`
412			`addi $a2,1`
413
414			`lui $a1,0x0002 # Leave with cache enabled`
415	109	ja_rd	`mfc0 $a0,$12`
416	229	ja_rd	`andi $a0,$a0,0xffff`
417			`or $a1,$a0,$a1`
418	109	ja_rd	`jr $ra`
419	229	ja_rd	`mtc0 $a1,$12`
420	109	ja_rd
421
422
423	78	ja_rd	`#--- Special functions that do not use any RAM ---------------------------------`
424	50	ja_rd	`# WARNING: Not for general use!`
425			`# All parameters in $a0..$a4, stack unused. No attempt to comply with any ABI`
426			`# has been made.`
427	109	ja_rd	`# Since we can't use any RAM, registers have been used with no regard for`
428			`# intended usage -- have to share reg bank with calling function.`
429
430	50	ja_rd	`# void puts(char *s) -- print zero-terminated string`
431	109	ja_rd	`puts:`
432	78	ja_rd	`la $a2,UART_BASE # UART base address`
433	50	ja_rd	`puts_loop:`
434			`lb $v0,0($a0)`
435			`beqz $v0,puts_end`
436			`addiu $a0,1`
437	109	ja_rd	`puts_wait_tx_rdy:`
438	78	ja_rd	`lw $v1,UART_STATUS($a2)`
439	229	ja_rd	`andi $v1,$v1,UART_TX_RDY`
440	50	ja_rd	`beqz $v1,puts_wait_tx_rdy`
441			`nop`
442	78	ja_rd	`sw $v0,UART_TX($a2)`
443	50	ja_rd	`b puts_loop`
444			`nop`
445	109	ja_rd
446	50	ja_rd	`puts_end:`
447			`jr $ra`
448	109	ja_rd	`nop`
449	50	ja_rd
450			`# void put_hex(int n, int d) -- print integer as d-digit hex`
451			`put_hex:`
452	78	ja_rd	`la $a2,UART_BASE`
453			`la $a3,put_hex_table`
454	50	ja_rd	`addi $a1,-1`
455			`add $a1,$a1,$a1`
456			`add $a1,$a1,$a1`
457
458			`put_hex_loop:`
459			`srlv $v0,$a0,$a1`
460			`andi $v0,$v0,0x0f`
461	78	ja_rd	`addu $s2,$a3,$v0`
462	50	ja_rd	`lb $v0,0($s2)`
463			`put_hex_wait_tx_rdy:`
464	78	ja_rd	`lw $v1,UART_STATUS($a2)`
465	229	ja_rd	`andi $v1,$v1,UART_TX_RDY`
466	50	ja_rd	`beqz $v1,put_hex_wait_tx_rdy`
467			`nop`
468	78	ja_rd	`sw $v0,UART_TX($a2)`
469	109	ja_rd
470	50	ja_rd	`bnez $a1,put_hex_loop`
471			`addi $a1,-4`
472
473			`jr $ra`
474			`nop`
475
476	109	ja_rd
477	50	ja_rd	`#---- Constant data (note we keep it in the text section) ----------------------`
478
479			`put_hex_table:`
480			`.ascii "0123456789abcdef"`
481
482	109	ja_rd	`msg0:`
483	50	ja_rd	`.ascii "\n\r"`
484			`.asciz "Scanning external memory at 0x"`
485			`msg1:`
486			`.asciz "Found XRAM top at 0x"`
487			`crlf:`
488			`.asciz "\n\r"`
489			`space:`
490			`.asciz " "`
491			`msg_mirror:`
492			`.asciz "hit mirror!\n\r"`
493			`msg_bad:`
494			`.asciz "bad readback!\n\r"`
495	78	ja_rd	`msg2:`
496			`.asciz "\n\rDumping the first few words of FLASH at address 0x"`
497	90	ja_rd	`msg3:`
498			`.ascii "\n\rTesting code execution from SRAM... "`
499			`.asciz "if you see this, it worked\n\r"`
500	109	ja_rd	`msg4:`

Browse

Tools

Subversion Repositories ion

[/] [ion/] [trunk/] [src/] [memtest/] [memtest.s] - Blame information for rev 249