OpenCores
URL https://opencores.org/ocsvn/mod_sim_exp/mod_sim_exp/trunk

Subversion Repositories mod_sim_exp

[/] [mod_sim_exp/] [trunk/] [doc/] [src/] [axi_interface.tex] - Blame information for rev 96

Go to most recent revision | Details | Compare with Previous | View Log

Line No. Rev Author Line
1 87 JonasDC
\chapter{AXI4-Lite interface}
2
\section{Structure}
3
The AXI4-Lite interface for this core acts as a slave to the AXI bus. It only supports the AXI-Lite procotol since there
4
is no ID reflection of the data transfer and only a 32-bit wide bus is supported. The AXI4-Lite IPcore block contains the
5
exponentiation core and a control register for the core its control inputs and outputs.
6
 
7
\section{Parameters}
8
This section describes the parameters used to configure the core, only the relevant parameters are discussed. AXI
9
specific parameters are left to the user to configure. The IP core specific parameters and their respective use are
10
listed in the table below.
11
\begin{center}
12
        \begin{tabular}{|l|p{6.5cm}|c|l|}
13
                \hline
14
                \rowcolor{Gray}
15
                \textbf{Name} & \textbf{Description} & \textbf{VHDL Type} &\textbf{Default Value} \bigstrut\\
16
                \hline
17
                \multicolumn{4}{|l|}{\textit{\textbf{Memory configuration}}} \\
18
                \hline
19
                \verb|C_FIFO_DEPTH| & depth of the generic FIFO, only applicable if \verb|C_MEM_STYLE| = \verb|"generic"| or \verb|"asym"|  & integer & 32 \bigstrut\\
20
                \hline
21
                \verb|C_MEM_STYLE| & the memory structure to use for the RAM, choice between 3 options: & string & \verb|"generic"| \bigstrut\\
22
                                                        & \verb|"xil_prim"| : use xilinx primitives & & \\
23
                                                & \verb|"generic"| : use general 32-bit RAMs & & \\
24
                                                & \verb|"asym"| : use asymmetric RAMs & & \\
25
                                                & (For more information see \ref{subsec:RAM_and_FIFO}) & & \bigstrut[b] \\
26
                \hline
27
                \verb|C_FPGA_MAN| & device manufacturer: & string & \verb|"xilinx"| \\
28
                                                & \verb|"xilinx"| or \verb|"altera"| &  &  \bigstrut\\
29
                \hline
30
                \verb|C_BASEADDR| & base address for the IP core's memory space & std\_logic\_vector & X"FFFFFFFF" \bigstrut\\
31
                \hline
32
                \verb|C_HIGHADDR| & high address for the IP core's memory space & std\_logic\_vector & X"00000000" \bigstrut\\
33
                \hline
34
                \multicolumn{4}{|l|}{\textit{\textbf{Multiplier configuration}}} \\
35
                \hline
36
                \verb|C_NR_BITS_TOTAL| & total width of the multiplier in bits & integer & 1536\bigstrut\\
37
                \hline
38
                \verb|C_NR_STAGES_TOTAL| & total number of stages in the pipeline & integer & 96\bigstrut\\
39
                \hline
40
                \verb|C_NR_STAGES_LOW| & number of lower stages in the pipeline, defines the bit-width of the lower pipeline part & integer & 32 \bigstrut\\
41
                \hline
42
                \verb|C_SPLIT_PIPELINE| & option to split the pipeline in 2 parts & boolean & true \bigstrut\\
43
                \hline
44
        \end{tabular}%
45
\end{center}
46
%\newline
47
\newpage
48
The IP core's memory space is organised in a fixed structure as show in Figure~\ref{AXImemstructure}. Only the upper 17
49
bits (31:15) of the base address can be chosen freely, the lower bits must be 0. So the \verb|C_BASEADDR| parameter must end
50
in 0xXXXX0000 or 0xXXXX8000 in hexadecimal representation. The core's memory space must have a minimum width of 28K byte for
51
all registers to be accessible.
52
\begin{figure}[H]
53
\centering
54
\includegraphics[trim=1.2cm 1.2cm 1.2cm 1.2cm, width=5cm]{pictures/axi_mem.pdf}
55
\caption{AXI4-Lite IP core memory structure}
56
\label{AXImemstructure}
57
\end{figure}
58
 
59
There are 4 parameters to configure the multiplier. These values define the width of the multiplier operands and the
60
number of pipeline stages. If \verb|C_SPLIT_PIPELINE| is false, only operands with a width of\\\verb|C_NR_BITS_TOTAL| are
61
valid. Else if \verb|C_SPLIT_PIPELINE| is true, 3 operand widths can be supported:
62
\begin{itemize}
63
  \item the length of the full pipeline ($C\_NR\_BITS\_TOTAL$)
64
  \item the length of the lower pipeline ($\frac{C\_NR\_BITS\_TOTAL}{C\_NR\_STAGES\_TOTAL} \cdot C\_NR\_STAGES\_LOW $)
65
  \item the length of the higher pipeline ($\frac{C\_NR\_BITS\_TOTAL}{C\_NR\_STAGES\_TOTAL} \cdot (C\_NR\_STAGES\_TOTAL - C\_NR\_STAGES\_LOW$)
66
\end{itemize}
67
 
68
\section{IO ports}
69
\begin{tabular}{|l|c|c|l|}
70
        \hline
71
        \rowcolor{Gray}
72
        \textbf{Port} & \textbf{Width} & \textbf{Direction} & \textbf{Description} \\
73
        \hline
74
        \multicolumn{4}{|l|}{\textit{\textbf{AXI4-Lite bus connections}}} \\
75
        \hline
76
        \verb|S_AXI_ACLK| & 1     & in & see note 1 \\
77
        \hline
78
        \verb|S_AXI_ARESETN| & 1     & in & see note 1 \\
79
        \hline
80
        \verb|S_AXI_AWADDR| & 32    & in & see note 1 \\
81
        \hline
82
        \verb|S_AXI_AWVALID| & 1     & in & see note 1 \\
83
        \hline
84
        \verb|S_AXI_AWREADY| & 1     & out & see note 1 \\
85
        \hline
86
        \verb|S_AXI_WDATA| & 32     & in & see note 1 \\
87
        \hline
88
        \verb|S_AXI_WVALID| & 1     & in & see note 1 \\
89
        \hline
90
        \verb|S_AXI_WREADY| & 1     & out & see note 1 \\
91
        \hline
92
        \verb|S_AXI_WSTRB| & 4     & in & see note 1 \\
93
        \hline
94
        \verb|S_AXI_BVALID| & 1    & out & see note 1 \\
95
        \hline
96
        \verb|S_AXI_BREADY| & 1     & in & see note 1 \\
97
        \hline
98
        \verb|S_AXI_BRESP| & 2     & out & see note 1 \\
99
        \hline
100
        \verb|S_AXI_ARADDR| & 32     & in & see note 1 \\
101
        \hline
102
        \verb|S_AXI_ARVALID| & 1     & in & see note 1 \\
103
        \hline
104
        \verb|S_AXI_ARREADY| & 1     & out & see note 1 \\
105
        \hline
106
        \verb|S_AXI_RDATA| & 32     & out & see note 1 \\
107
        \hline
108
        \verb|S_AXI_RVALID| & 1    & out & see note 1 \\
109
        \hline
110
        \verb|S_AXI_RREADY| & 1     & in & see note 1 \\
111
        \hline
112
        \verb|S_AXI_RRESP| & 2     & out & see note 1 \\
113
        \hline
114
        \multicolumn{4}{|l|}{\textit{\textbf{Core signals}}} \\
115
        \hline
116
        \verb|IntrEvent| & 1     & out   & core interrupt signal \\
117
        \hline
118
        \verb|calc_time| & 1     & out   & is high when core is performing a multiplication, for monitoring \\
119
        \hline
120
\end{tabular}%
121
\newline \newline
122
\textbf{Note 1:} The function and timing of this signal is defined in the AMBA\textsuperscript{\textregistered} AXI Protocol Version: 2.0 Specification.
123
 
124
\section{Registers}
125
This section specifies the IP core internal registers as seen from the software. These registers allow to control and
126
configure the modular exponentiation core and to read out its state. All addresses given in this table are relative to the
127
IP core's base address.\\
128
\newline
129
% Table generated by Excel2LaTeX
130
\begin{tabular}{|l|c|c|c|l|}
131
\hline
132
\rowcolor{Gray}
133
\textbf{Name} & \textbf{Width} & \textbf{Address} & \textbf{Access} & \textbf{Description} \bigstrut\\
134
\hline
135
control register                & 32 & 0x6000 & RW      & multiplier core control signals and \bigstrut[t]\\
136
                                                &       &               &               & interrupt flags register\bigstrut[b]\\
137
\hline
138
\end{tabular}%
139
\newpage
140
\subsection{Control register (offset = 0x6000)}
141
This registers holds the control inputs to the multiplier core and the interrupt flags.\\
142
\begin{figure}[H]
143
\centering
144
\includegraphics[trim=1.2cm 1.2cm 1.2cm 1.2cm, width=15cm]{pictures/axi_control_reg.pdf}
145
\caption{control register}
146
\end{figure}
147
 
148
\begin{tabular}{ll}
149
bits 31-30      & P\_SEL : selects which pipeline part to be active\\
150
                        & $\bullet$  "01" lower pipeline part\\
151
                        & $\bullet$  "10" higher pipeline part\\
152
                        & $\bullet$  "11" full pipeline\\
153
                        & $\bullet$  "00" invalid selection\\
154
                        &\\
155
bits 29-28      & DEST\_OP : selects the operand (0-3) to store the result in for a single\\
156
                        & Montgomery multiplication\footnotemark\\
157
                        &\\
158
bits 27-26      & X\_OP : selects the x operand (0-3) for a single Montgomery multiplication\footnotemark[\value{footnote}]\\
159
                        &\\
160
bits 25-24      & Y\_OP : selects the y operand (0-3) for a single Montgomery multiplication\footnotemark[\value{footnote}]\\
161
                        &\\
162
bit 23          & START : starts the multiplication/exponentiation\\
163
                        &\\
164
bit 22          & EXP/M : selects the operating mode\\
165
                        & $\bullet$  "0" single Montgomery multiplications\\
166
                        & $\bullet$  "1" simultaneous exponentiations\\
167
                        &\\
168 88 JonasDC
bit 21          & unimplemented\\
169
                        &\\
170
bit 20          & RESET : active high reset for the core\footnotemark[2]\\
171 87 JonasDC
                        &\\
172 88 JonasDC
bits 19-16      & unimplemented\\
173 87 JonasDC
                        &\\
174
bit 15          & READY : ready flag, "1" when multiplication is done\\
175
                        & must be cleared in software\\
176
                        &\\
177
bit 14          & MEM\_ERR : memory collision error flag, "1" when write error occurred\\
178
                        & must be cleared in software\\
179
                        &\\
180
bit 13          & FIFO\_FULL : FIFO full error flag, "1" when FIFO is full\\
181
                        & must be cleared in software\\
182
                        &\\
183
bit 12          & FIFO\_ERR : FIFO write/push error flag, "1" when push error occurred\\
184
                        & must be cleared in software\\
185
                        &\\
186
bits 11-0       & unimplemented\\
187
                        &\\
188
\end{tabular}
189
\newline
190
\newline
191
\footnotetext[1]{when the core is running in exponentiation mode, the parameters DEST\_OP, X\_OP and Y\_OP have no effect.}
192
\footnotetext[2]{The reset affects the full IP core, thus resetting the control register, interrupt controller,
193
the multiplier pipeline, FIFO and control logic of the core.}
194
\newpage
195
\section{Interfacing the core's RAM}
196
Special attention must be taken when writing data to the operands and modulus. The least significant bit of the data has be on the lowest
197
address and the most significant bit on the highest address. A write to the RAM has to happen 1 word at a time, byte writes are not
198
supported due to the structure of the RAM.
199
 
200
\section{Handling interrupts}
201 92 JonasDC
When the embedded processor receives an interrupt signal from this core, it is up to the controlling software to determine the source of the interrupt by reading out the interrupt flags of the control register. After handling the interrupt, the appropriate flag must be cleared by user. A reset or core start operation also resets the flags. The interrupt signal is high level sensitive.

powered by: WebSVN 2.1.0

© copyright 1999-2024 OpenCores.org, equivalent to Oliscience, all rights reserved. OpenCores®, registered trademark.