Subversion Repositories open8_urisc

-- Copyright (c)2020 Jeremy Seth Henry

-- All rights reserved.

--

-- Redistribution and use in source and binary forms, with or without

-- modification, are permitted provided that the following conditions are met:

--     * Redistributions of source code must retain the above copyright

--       notice, this list of conditions and the following disclaimer.

--     * Redistributions in binary form must reproduce the above copyright

--       notice, this list of conditions and the following disclaimer in the

--       documentation and/or other materials provided with the distribution,

--       where applicable (as part of a user interface, debugging port, etc.)

--

-- THIS SOFTWARE IS PROVIDED BY JEREMY SETH HENRY ``AS IS'' AND ANY

-- EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

-- WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

-- DISCLAIMED. IN NO EVENT SHALL JEREMY SETH HENRY BE LIABLE FOR ANY

-- DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

-- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

-- LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

-- ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

-- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

-- THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

--

-- VHDL Units :  o8_elapsed_usec

-- Description:  Provides an 24-bit microsecond resolution counter for

--            :   measuring events

--

-- Register Map:

-- Offset  Bitfield Description                        Read/Write

--   0x00  AAAAAAAA Time Accumulator Byte 0               (RW*)

--   0x01  AAAAAAAA Time Accumulator Byte 1               (RW*)

--   0x02  AAAAAAAA Time Accumulator Byte 2               (RW*)

--   0x03  BA------ Control/Status Register               (RW)

--                   A: Reset (1)

--                   B: Start (1) / Stop (0) (status on RD)

--

-- Notes      :  Writing to 0x0 - 0x02 will latch the current value

--            :  Writing a 1 to bit A of 0x03 will cause an

--                immediate timer reset. This bit is a one-shot.

--

-- Revision History

-- Author          Date     Change

------------------ -------- ---------------------------------------------------

-- Seth Henry      04/20/20 Design Start

-- Seth Henry      05/18/20 Added write qualification input

library ieee;

use ieee.std_logic_1164.all;

  use ieee.std_logic_unsigned.all;

  use ieee.std_logic_arith.all;

  use ieee.std_logic_misc.all;

library work;

  use work.open8_pkg.all;

entity o8_elapsed_usec is

generic(

  Address                    : ADDRESS_TYPE

);

port(

  Open8_Bus                  : in  OPEN8_BUS_TYPE;

  Write_Qual                 : in  std_logic := '1';

  Rd_Data                    : out DATA_TYPE

);

end entity;

architecture behave of o8_elapsed_usec is

  alias Clock                is Open8_Bus.Clock;

  alias Reset                is Open8_Bus.Reset;

  alias uSec_Tick            is Open8_Bus.uSec_Tick;

  constant User_Addr         : std_logic_vector(15 downto 2) :=

                                Address(15 downto 2);

  alias  Comp_Addr           is Open8_Bus.Address(15 downto 2);

  signal Addr_Match          : std_logic := '0';

  alias  Reg_Sel_d           is Open8_Bus.Address(1 downto 0);

  signal Reg_Sel_q           : std_logic_vector(1 downto 0) := "00";

  signal Wr_En_d             : std_logic := '0';

  signal Wr_En_q             : std_logic := '0';

  alias  Wr_Data_d           is Open8_Bus.Wr_Data;

  signal Wr_Data_q           : DATA_TYPE := x"00";

  signal Rd_En_d             : std_logic := '0';

  signal Rd_En_q             : std_logic := '0';

  signal Shadow_Time         : std_logic_vector(23 downto 0) := x"000000";

  alias  Shadow_Time_B0      is Shadow_Time( 7 downto  0);

  alias  Shadow_Time_B1      is Shadow_Time(15 downto  8);

  alias  Shadow_Time_B2      is Shadow_Time(23 downto 16);

  signal Update_Shadow       : std_logic := '0';

  signal Timer_Reset         : std_logic := '0';

  signal Timer_En_Req        : std_logic := '0';

  signal Timer_Enable        : std_logic := '0';

  signal Timer_Cnt           : std_logic_vector(23 downto 0) := x"000000";

begin

  Addr_Match                 <= '1' when Comp_Addr = User_Addr else '0';

  Wr_En_d                    <= Addr_Match and Open8_Bus.Wr_En;

  Rd_En_d                    <= Addr_Match and Open8_Bus.Rd_En;

  io_reg: process( Clock, Reset )

  begin

    if( Reset = Reset_Level )then

      Reg_Sel_q              <= "00";

      Wr_En_q                <= '0';

      Wr_Data_q              <= x"00";

      Rd_En_q                <= '0';

      Rd_Data                <= OPEN8_NULLBUS;

      Update_Shadow          <= '0';

      Timer_Reset            <= '0';

      Timer_En_Req           <= '0';

    elsif( rising_edge( Clock ) )then

      Reg_Sel_q              <= Reg_Sel_d;

      Wr_En_q                <= Wr_En_d;

      Wr_Data_q              <= Wr_Data_d;

      Update_Shadow          <= '0';

      Timer_Reset            <= '0';

      if( Wr_En_q = '1' and Write_Qual = '1' )then

        case( Reg_Sel_q )is

          when "00" | "01" | "10" =>

            Update_Shadow    <= '1';

          when "11" =>

            Timer_Reset      <= Wr_Data_q(6);

            Timer_En_Req     <= Wr_Data_q(7);

          when others => null;

        end case;

      end if;

      Rd_Data                <= OPEN8_NULLBUS;

      Rd_En_q                <= Rd_En_d;

      if( Rd_En_q = '1' )then

        case( Reg_Sel_q )is

          when "00" =>

            Rd_Data          <= Shadow_Time_B0;

          when "01" =>

            Rd_Data          <= Shadow_Time_B1;

          when "10" =>

            Rd_Data          <= Shadow_Time_B2;

          when "11" =>

            Rd_Data          <= Timer_En_Req & "0000000";

          when others => null;

        end case;

      end if;

    end if;

  end process;

  Timer_proc: process( Clock, Reset )

  begin

    if( Reset = Reset_Level )then

      Shadow_Time            <= x"000000";

      Timer_Cnt              <= x"000000";

    elsif( rising_edge(Clock) )then

      if( Timer_Reset = '1' )then

        Timer_Cnt              <= x"000000";

      elsif( Timer_Enable = '1' )then

        Timer_Cnt            <= Timer_Cnt + uSec_Tick;

      end if;

      if( uSec_Tick = '1' )then

        Timer_Enable         <= Timer_En_Req;

      end if;

      if( Update_Shadow = '1' )then

        Shadow_Time          <= Timer_Cnt;

      end if;

    end if;

  end process;

end architecture;