Subversion Repositories open8_urisc

-- Copyright (c)2020 Jeremy Seth Henry

-- All rights reserved.

--

-- Redistribution and use in source and binary forms, with or without

-- modification, are permitted provided that the following conditions are met:

--     * Redistributions of source code must retain the above copyright

--       notice, this list of conditions and the following disclaimer.

--     * Redistributions in binary form must reproduce the above copyright

--       notice, this list of conditions and the following disclaimer in the

--       documentation and/or other materials provided with the distribution,

--       where applicable (as part of a user interface, debugging port, etc.)

--

-- THIS SOFTWARE IS PROVIDED BY JEREMY SETH HENRY ``AS IS'' AND ANY

-- EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

-- WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

-- DISCLAIMED. IN NO EVENT SHALL JEREMY SETH HENRY BE LIABLE FOR ANY

-- DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

-- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

-- LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

-- ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

-- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

-- THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

--

-- VHDL Units :  o8_sdlc_if

-- Description:  Provides a full memory-mapped SDLC stack with automatic CRC16

--                Checksum insertion and integrity checking.

--

-- Transmit Memory Map

-- "0_0000_0000" (0x000) TX Buffer START

-- "0_1111_1101" (0x0FD) TX Buffer END

-- "0_1111_1110" (0x0FE) Clock Status*

-- "0_1111_1111" (0x0FF) TX Length / Status**

--

-- Receive Memory Map

-- "1_0000_0000" (0x100) RX Buffer START

-- "1_1111_1101" (0x1FD) RX Buffer END

-- "1_1111_1110" (0x0FE) RX Checksum Status***

-- "1_1111_1111" (0x1FF) RX Length   Status****

--

-- *    Address 0xFE reports the SDLC bit clock status and updates on changes.

--      1) If BClk_Okay = '0' (Bitclock is NOT present), the field will report

--          0x00. Otherwise, it will report 0xFF if the bitclock is present.

--      2) Writing any value to the register will cause the controller to

--         silently reset the clock status without causing an interrupt.

--

-- **   This location serves as the control/status register for transmit

--      1) Writing a value between 1 and 253 will trigger the transmit engine,

--          using the write value as the packet length.

--      2) Values 0x00, 0xFE, or 0xFF are invalid, and will be ignored.

--      3) This value will change from the user written value to 0xFF once the

--          packet is transmitted to indicate the transmission is complete.

--

-- ***  This location serves as the status register for receive checksum test

--      1) A value of 0x00 indicates the CRC did NOT match, while a value

--         of 0xFF indicates that the recieved CRC matches the calculated CRC.

--

-- **** This location serves as the status register for the receive

--      1) This value is only updated on reception of a full frame, indicated

--          by a start followed by a stop flag. Incomplete frames are ignored.

--      2) If too many bytes are received (buffer overflow), a value of

--          ERR_LENGTH is written.

--

-- Revision History

-- Author          Date     Change

------------------ -------- ---------------------------------------------------

-- Seth Henry      04/16/20 Revision block added

-- Seth Henry      05/18/20 Added write qualification input

library ieee;

  use ieee.std_logic_1164.all;

  use ieee.std_logic_unsigned.all;

  use ieee.std_logic_arith.all;

library work;

  use work.open8_pkg.all;

library work;

  use work.sdlc_serial_pkg.all;

entity o8_sdlc_if is

generic(

  Poly_Init                  : std_logic_vector(15 downto 0) := x"0000";

  Set_As_Master              : boolean := true;

  Clock_Offset               : integer := 6;

  BitClock_Frequency         : real := 500000.0;

  Clock_Frequency            : real := 100000000.0;

  Address                    : ADDRESS_TYPE

);

port(

  Open8_Bus                  : in  OPEN8_BUS_TYPE;

  Write_Qual                 : in  std_logic := '1';

  Rd_Data                    : out DATA_TYPE;

  TX_Interrupt               : out std_logic;

  RX_Interrupt               : out std_logic;

  -- Serial IO

  SDLC_In                    : in  std_logic;

  SDLC_SClk                  : in  std_logic;

  SDLC_MClk                  : out std_logic;

  SDLC_Out                   : out std_logic

);

end entity;

architecture behave of o8_sdlc_if is

  alias Clock                is Open8_Bus.Clock;

  alias Reset                is Open8_Bus.Reset;

  constant Base_Addr         : std_logic_vector(15 downto 9)

                               := Address(15 downto 9);

  alias CPU_Upper_Addr       is Open8_Bus.Address(15 downto 9);

  signal Base_Addr_Match     : std_logic := '0';

  alias  DP_A_Addr           is Open8_Bus.Address(8 downto 0);

  signal DP_A_Wr_En          : std_logic := '0';

  alias  DP_A_Wr_Data        is Open8_Bus.Wr_Data;

  signal DP_A_Rd_En_d        : std_logic := '0';

  signal DP_A_Rd_En_q        : std_logic := '0';

  signal DP_A_Rd_Data        : DATA_TYPE := OPEN8_NULLBUS;

  constant Reg_Sub_Addr      : std_logic_vector(8 downto 1) := x"7F";

  alias Reg_Upper_Addr       is Open8_Bus.Address(8 downto 1);

  alias Reg_Lower_Addr       is Open8_Bus.Address(0);

  signal Reg_Addr            : std_logic_vector(8 downto 1) := (others => '0');

  signal Reg_Sel             : std_logic     := '0';

  signal Reg_Wr_En_d         : std_logic     := '0';

  signal Reg_Wr_En_q         : std_logic     := '0';

  signal Reg_Clk_Sel         : std_logic     := '0';

  signal Reg_TxS_Sel         : std_logic     := '0';

  signal DP_B_Addr           : std_logic_vector(8 downto 0) := (others => '0');

  signal DP_B_Wr_Data        : DATA_IN_TYPE  := x"00";

  signal DP_B_Wr_En          : std_logic     := '0';

  signal DP_B_Rd_Data        : DATA_IN_TYPE  := x"00";

  signal DP_Port0_Addr       : DATA_IN_TYPE  := x"00";

  signal DP_Port0_RWn        : std_logic     := '0';

  signal DP_Port0_WrData     : DATA_IN_TYPE  := x"00";

  signal DP_Port0_RdData     : DATA_IN_TYPE  := x"00";

  signal DP_Port0_Req        : std_logic     := '0';

  signal DP_Port0_Ack        : std_logic     := '0';

  signal DP_Port1_Addr       : DATA_IN_TYPE  := x"00";

  signal DP_Port1_RWn        : std_logic     := '0';

  signal DP_Port1_WrData     : DATA_IN_TYPE  := x"00";

  signal DP_Port1_RdData     : DATA_IN_TYPE  := x"00";

  signal DP_Port1_Req        : std_logic     := '0';

  signal DP_Port1_Ack        : std_logic     := '0';

  signal BClk_RE             : std_logic     := '0';

  signal BClk_FE             : std_logic     := '0';

  signal BClk_Okay           : std_logic     := '0';

  signal TX_Wr_En            : std_logic     := '0';

  signal TX_Wr_Flag          : std_logic     := '0';

  signal TX_Wr_Data          : DATA_IN_TYPE  := x"00";

  signal TX_Req_Next         : std_logic     := '0';

  signal TX_CRC_Clr          : std_logic     := '0';

  signal TX_CRC_En           : std_logic     := '0';

  signal TX_CRC_Data         : CRC_OUT_TYPE  := x"0000";

  signal TX_CRC_Valid        : std_logic     := '0';

  signal RX_Valid            : std_logic     := '0';

  signal RX_Flag             : std_logic     := '0';

  signal RX_Data             : DATA_IN_TYPE;

  signal RX_Idle             : std_logic     := '0';

  signal RX_Frame_Start      : std_logic     := '0';

  signal RX_Frame_Stop       : std_logic     := '0';

  signal RX_Frame_Valid      : std_logic     := '0';

  signal RX_Frame_Data       : DATA_IN_TYPE  := x"00";

  signal RX_CRC_Valid        : std_logic     := '0';

  signal RX_CRC_Data         : CRC_OUT_TYPE  := x"0000";

begin

-- ***************************************************************************

-- *          Open8 Bus Interface and Control Register Detection             *

-- ***************************************************************************

  -- This decode needs to happen immediately, to give the RAM a chance to

  --  do the lookup before we have to set Rd_Data

  Base_Addr_Match            <= '1' when Base_Addr = CPU_Upper_Addr else '0';

  Reg_Wr_En_d                <= Base_Addr_Match and

                                Open8_Bus.Wr_En and

                                Write_Qual;

  DP_A_Wr_En                 <= Base_Addr_Match and

                                Open8_Bus.Wr_En and

                                Write_Qual;

  DP_A_Rd_En_d               <= Base_Addr_Match and Open8_Bus.Rd_En;

  CPU_IF_proc: process( Reset, Clock )

  begin

    if( Reset = Reset_Level )then

      Reg_Addr               <= (others => '0');

      Reg_Wr_En_q            <= '0';

      Reg_Clk_Sel            <= '0';

      Reg_TxS_Sel            <= '0';

      DP_A_Rd_En_q           <= '0';

      Rd_Data                <= OPEN8_NULLBUS;

    elsif( rising_edge(Clock) )then

      Reg_Addr               <= Reg_Upper_Addr;

      Reg_Sel                <= Reg_Lower_Addr;

      Reg_Wr_En_q            <= Reg_Wr_En_d;

      Reg_Clk_Sel            <= '0';

      Reg_TxS_Sel            <= '0';

      if( Reg_Addr = Reg_Sub_Addr )then

        Reg_Clk_Sel          <= Reg_Wr_En_q and not Reg_Sel;

        Reg_TxS_Sel          <= Reg_Wr_En_q and Reg_Sel;

      end if;

      DP_A_Rd_En_q           <= DP_A_Rd_En_d;

      Rd_Data                <= OPEN8_NULLBUS;

      if( DP_A_Rd_En_q = '1' )then

        Rd_Data              <= DP_A_Rd_Data;

      end if;

    end if;

  end process;

-- ***************************************************************************

-- *                     Shared Dual-Port Memory                             *

-- ***************************************************************************

  U_RAM : entity work.sdlc_dp512b_ram

  port map(

    clock                    => Clock,

    address_a                => DP_A_Addr,

    address_b                => DP_B_Addr,

    data_a                   => DP_A_Wr_Data,

    data_b                   => DP_B_Wr_Data,

    wren_a                   => DP_A_Wr_En,

    wren_b                   => DP_B_Wr_En,

    q_a                      => DP_A_Rd_Data,

    q_b                      => DP_B_Rd_Data

  );

-- ***************************************************************************

-- *                     Memory Arbitration                                  *

-- ***************************************************************************

  U_ARB : entity work.sdlc_serial_arbfsm

  generic map(

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    DP_Addr                  => DP_B_Addr,

    DP_Wr_Data               => DP_B_Wr_Data,

    DP_Wr_En                 => DP_B_Wr_En,

    DP_Rd_Data               => DP_B_Rd_Data,

    --

    DP_Port0_Addr            => DP_Port0_Addr,

    DP_Port0_RWn             => DP_Port0_RWn,

    DP_Port0_WrData          => DP_Port0_WrData,

    DP_Port0_RdData          => DP_Port0_RdData,

    DP_Port0_Req             => DP_Port0_Req,

    DP_Port0_Ack             => DP_Port0_Ack,

    --

    DP_Port1_Addr            => DP_Port1_Addr,

    DP_Port1_RWn             => DP_Port1_RWn,

    DP_Port1_WrData          => DP_Port1_WrData,

    DP_Port1_RdData          => DP_Port1_RdData,

    DP_Port1_Req             => DP_Port1_Req,

    DP_Port1_Ack             => DP_Port1_Ack

  );

-- ***************************************************************************

-- *                        Serial BitClock                                  *

-- ***************************************************************************

  U_BCLK : entity work.sdlc_serial_clk

  generic map(

    Set_As_Master            => Set_As_Master,

    BitClock_Freq            => BitClock_Frequency,

    Reset_Level              => Reset_Level,

    Sys_Freq                 => Clock_Frequency

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    BClk_In                  => SDLC_SClk,

    BClk_Out                 => SDLC_MClk,

    BClk_FE                  => BClk_FE,

    BClk_RE                  => BClk_RE,

    BClk_Okay                => BClk_Okay

  );

-- ***************************************************************************

-- *                     Serial Transmit Path                                *

-- ***************************************************************************

  U_TXFSM: entity work.sdlc_serial_txfsm

  generic map(

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    BClk_Okay                => BClk_Okay,

    --

    Reg_Clk_Sel              => Reg_Clk_Sel,

    Reg_TxS_Sel              => Reg_TxS_Sel,

    --

    DP_Port0_Addr            => DP_Port0_Addr,

    DP_Port0_RWn             => DP_Port0_RWn,

    DP_Port0_WrData          => DP_Port0_WrData,

    DP_Port0_RdData          => DP_Port0_RdData,

    DP_Port0_Req             => DP_Port0_Req,

    DP_Port0_Ack             => DP_Port0_Ack,

    --

    TX_Wr_En                 => TX_Wr_En,

    TX_Wr_Flag               => TX_Wr_Flag,

    TX_Wr_Data               => TX_Wr_Data,

    TX_Req_Next              => TX_Req_Next,

    --

    TX_CRC_Clr               => TX_CRC_Clr,

    TX_CRC_En                => TX_CRC_En,

    TX_CRC_Data              => TX_CRC_Data,

    TX_CRC_Valid             => TX_CRC_Valid,

    --

    TX_Interrupt             => TX_Interrupt

  );

  U_TX_CRC : entity work.sdlc_crc16_ccitt

  generic map(

    Poly_Init                => Poly_Init,

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    Clear                    => TX_CRC_Clr,

    Wr_En                    => TX_CRC_En,

    Wr_Data                  => TX_Wr_Data,

    --

    CRC16_Valid              => TX_CRC_Valid,

    CRC16_Out                => TX_CRC_Data

  );

  U_TX_SER : entity work.sdlc_serial_tx

  generic map(

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    BClk_FE                  => BClk_FE,

    BClk_RE                  => BClk_RE,

    BClk_Okay                => BClk_Okay,

    --

    TX_En                    => TX_Wr_En,

    TX_FSS_Flag              => TX_Wr_Flag,

    TX_Data                  => TX_Wr_Data,

    TX_Req_Next              => TX_Req_Next,

    --

    Serial_Out               => SDLC_Out

  );

-- ***************************************************************************

-- *                     Serial Receive Path                                 *

-- ***************************************************************************

  U_RX_SER : entity work.sdlc_serial_rx

  generic map(

    Set_As_Master            => Set_As_Master,

    Clock_Offset             => Clock_Offset,

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    BClk_RE                  => BClk_RE,

    BClk_Okay                => BClk_Okay,

    --

    Serial_In                => SDLC_In,

    --

    RX_Valid                 => RX_Valid,

    RX_Flag                  => RX_Flag,

    RX_Data                  => RX_Data,

    RX_Idle                  => RX_Idle

  );

  U_RX_PKT : entity work.sdlc_serial_frame

  generic map(

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    RX_Valid                 => RX_Valid,

    RX_Flag                  => RX_Flag,

    RX_Data                  => RX_Data,

    RX_Idle                  => RX_Idle,

    --

    RX_Frame_Start           => RX_Frame_Start,

    RX_Frame_Stop            => RX_Frame_Stop,

    RX_Frame_Valid           => RX_Frame_Valid,

    RX_Frame_Data            => RX_Frame_Data

  );

  U_RX_CRC : entity work.sdlc_crc16_ccitt

  generic map(

    Poly_Init                => Poly_Init,

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    Clear                    => RX_Frame_Start,

    Wr_En                    => RX_Frame_Valid,

    Wr_Data                  => RX_Frame_Data,

    --

    CRC16_Valid              => RX_CRC_Valid,

    CRC16_Out                => RX_CRC_Data

  );

  U_RX_FSM : entity work.sdlc_serial_rxfsm

  generic map(

    Reset_Level              => Reset_Level

  )

  port map(

    Clock                    => Clock,

    Reset                    => Reset,

    --

    BClk_Okay                => BClk_Okay,

    --

    DP_Port1_Addr            => DP_Port1_Addr,

    DP_Port1_RWn             => DP_Port1_RWn,

    DP_Port1_WrData          => DP_Port1_WrData,

    DP_Port1_RdData          => DP_Port1_RdData,

    DP_Port1_Req             => DP_Port1_Req,

    DP_Port1_Ack             => DP_Port1_Ack,

    --

    RX_CRC_Valid             => RX_CRC_Valid,

    RX_CRC_Data              => RX_CRC_Data,

    --

    RX_Frame_Start           => RX_Frame_Start,

    RX_Frame_Stop            => RX_Frame_Stop,

    RX_Frame_Valid           => RX_Frame_Valid,

    RX_Frame_Data            => RX_Frame_Data,

    --

    RX_Interrupt             => RX_Interrupt

  );

end architecture;