Subversion Repositories open8_urisc

-- Copyright (c)2006, 2016, 2019, 2020 Jeremy Seth Henry

-- All rights reserved.

--

-- Redistribution and use in source and binary forms, with or without

-- modification, are permitted provided that the following conditions are met:

--     * Redistributions of source code must retain the above copyright

--       notice, this list of conditions and the following disclaimer.

--     * Redistributions in binary form must reproduce the above copyright

--       notice, this list of conditions and the following disclaimer in the

--       documentation and/or other materials provided with the distribution,

--       where applicable (as part of a user interface, debugging port, etc.)

--

-- THIS SOFTWARE IS PROVIDED BY JEREMY SETH HENRY ``AS IS'' AND ANY

-- EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED

-- WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE

-- DISCLAIMED. IN NO EVENT SHALL JEREMY SETH HENRY BE LIABLE FOR ANY

-- DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES

-- (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

-- LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND

-- ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT

-- (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF

-- THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

--

-- VHDL Units :  o8_sys_timer

-- Description:  Provides an 8-bit microsecond resolution timer for generating

--            :   periodic interrupts for the Open8 CPU.

--

-- Notes      :  It is possible to set the value to zero, resulting in the

--            :   output staying high indefinitely. This may cause an issue if

--            :   the output is connected to an interrupt input.

--            :  Also provides uSec_Tick as an output

--

-- Revision History

-- Author          Date     Change

------------------ -------- ---------------------------------------------------

-- Seth Henry      07/28/11 Design Start

-- Seth Henry      12/19/19 Renamed Tmr_Out to Interrupt

-- Seth Henry      04/09/20 Modified timer update logic to reset the timer on

--                           interval write.

-- Seth Henry      04/16/20 Modified to use Open8 bus record

library ieee;

use ieee.std_logic_1164.all;

  use ieee.std_logic_unsigned.all;

  use ieee.std_logic_arith.all;

  use ieee.std_logic_misc.all;

library work;

  use work.open8_pkg.all;

entity o8_sys_timer is

generic(

  Address                    : ADDRESS_TYPE

);

port(

  Open8_Bus                  : in  OPEN8_BUS_TYPE;

  Rd_Data                    : out DATA_TYPE;

  Interrupt                  : out std_logic

);

end entity;

architecture behave of o8_sys_timer is

  alias Clock                is Open8_Bus.Clock;

  alias Reset                is Open8_Bus.Reset;

  alias uSec_Tick            is Open8_Bus.uSec_Tick;

  constant User_Addr         : ADDRESS_TYPE := Address;

  alias  Comp_Addr           is Open8_Bus.Address(15 downto 0);

  signal Addr_Match          : std_logic := '0';

  signal Wr_En               : std_logic := '0';

  signal Wr_Data_q           : DATA_TYPE := x"00";

  signal Rd_En               : std_logic := '0';

  signal Rd_En_q             : std_logic := '0';

  signal Interval            : DATA_TYPE := x"00";

  signal Update_Interval     : std_logic;

  signal Timer_Cnt           : DATA_TYPE := x"00";

begin

  Addr_Match                 <= '1' when Comp_Addr = User_Addr else '0';

  io_reg: process( Clock, Reset )

  begin

    if( Reset = Reset_Level )then

      Wr_En                  <= '0';

      Wr_Data_q              <= x"00";

      Rd_En                  <= '0';

      Rd_Data                <= OPEN8_NULLBUS;

      Interval               <= x"00";

      Update_Interval        <= '0';

    elsif( rising_edge( Clock ) )then

      Wr_En                  <= Addr_Match and Open8_Bus.Wr_En;

      Wr_Data_q              <= Open8_Bus.Wr_Data;

      Update_Interval        <= '0';

      if( Wr_En = '1' )then

        Interval             <= Wr_Data_q;

        Update_Interval      <= '1';

      end if;

      Rd_Data                <= (others => '0');

      Rd_En                  <= Addr_Match and Open8_Bus.Rd_En;

      if( Rd_En = '1' )then

        Rd_Data              <= Interval;

      end if;

    end if;

  end process;

  Interval_proc: process( Clock, Reset )

  begin

    if( Reset = Reset_Level )then

      Timer_Cnt              <= x"00";

      Interrupt              <= '0';

    elsif( rising_edge(Clock) )then

      Interrupt              <= '0';

      Timer_Cnt              <= Timer_Cnt - uSec_Tick;

      if( Update_Interval = '1' )then

        Timer_Cnt            <= Interval;

      elsif( or_reduce(Timer_Cnt) = '0' )then

        Timer_Cnt            <= Interval;

        Interrupt            <= or_reduce(Interval); -- Only trigger on Int > 0

      end if;

    end if;

  end process;

end architecture;