Subversion Repositories openarty

////////////////////////////////////////////////////////////////////////////////

//

// Filename:    fastio.v

//

// Project:     OpenArty, an entirely open SoC based upon the Arty platform

//

// Purpose:     

//

// Creator:     Dan Gisselquist, Ph.D.

//              Gisselquist Technology, LLC

//

////////////////////////////////////////////////////////////////////////////////

//

// Copyright (C) 2015-2016, Gisselquist Technology, LLC

//

// This program is free software (firmware): you can redistribute it and/or

// modify it under the terms of  the GNU General Public License as published

// by the Free Software Foundation, either version 3 of the License, or (at

// your option) any later version.

//

// This program is distributed in the hope that it will be useful, but WITHOUT

// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or

// FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License

// for more details.

//

// You should have received a copy of the GNU General Public License along

// with this program.  (It's in the $(ROOT)/doc directory, run make with no

// target there if the PDF file isn't present.)  If not, see

// <http://www.gnu.org/licenses/> for a copy.

//

// License:     GPL, v3, as defined and found on www.gnu.org,

//              http://www.gnu.org/licenses/gpl.html

//

//

////////////////////////////////////////////////////////////////////////////////

//

//

`include "builddate.v"

//

module  fastio(i_clk,

                // Board level I/O

                i_sw, i_btn, o_led,

                o_clr_led0, o_clr_led1, o_clr_led2, o_clr_led3,

                // Board level PMod I/O

                i_aux_rx, o_aux_tx, o_aux_cts, i_gps_rx, o_gps_tx,

                // i_gpio, o_gpio,

                // Wishbone control

                i_wb_cyc, i_wb_stb, i_wb_we, i_wb_addr,

                        i_wb_data, o_wb_ack, o_wb_stall, o_wb_data,

                // Cross-board I/O

                i_rtc_ppd, i_buserr, i_other_ints, o_bus_int, o_board_ints);

        parameter       AUXUART_SETUP = 30'd1736, // 115200 baud from 200MHz clk

                        GPSUART_SETUP = 30'd20833; // 9600 baud from 200MHz clk

        input                   i_clk;

        // Board level I/O

        input           [3:0]    i_sw;

        input           [3:0]    i_btn;

        output  wire    [3:0]    o_led;

        output  reg     [2:0]    o_clr_led0;

        output  reg     [2:0]    o_clr_led1;

        output  reg     [2:0]    o_clr_led2;

        output  reg     [2:0]    o_clr_led3;

        // Board level PMod I/O

        //

        // Auxilliary UART I/O

        input           i_aux_rx;

        output  wire    o_aux_tx, o_aux_cts;

        //

        // GPS UART I/O

        input           i_gps_rx;

        output  wire    o_gps_tx;

        //

        // GPIO

        // input        [(NGPI-1):0]    i_gpio;

        // output reg   [(NGPO-1):0]    o_gpio;

        //

        // Wishbone inputs

        input                   i_wb_cyc, i_wb_stb, i_wb_we;

        input           [4:0]    i_wb_addr;

        input           [31:0]   i_wb_data;

        // Wishbone outputs

        output  reg             o_wb_ack;

        output  wire            o_wb_stall;

        output  reg     [31:0]   o_wb_data;

        // A strobe at midnight, to keep the calendar on "time"

        input                   i_rtc_ppd;

        // Address of the last bus error

        input           [31:0]   i_buserr;

        //

        // Interrupts -- both the output bus interrupt, as well as those

        //      internally generated interrupts which may be used elsewhere

        //      in the design

        input   wire    [8:0]    i_other_ints;

        output  wire            o_bus_int;

        output  wire    [5:0]    o_board_ints; // Button and switch interrupts

        reg             last_wb_stb;

        reg     [4:0]    last_wb_addr;

        reg     [31:0]   last_wb_data;

        initial last_wb_stb = 1'b0;

        always @(posedge i_clk)

        begin

                last_wb_addr <= i_wb_addr;

                last_wb_data <= i_wb_data;

                last_wb_stb  <= (i_wb_stb)&&(i_wb_we);

        end

        wire    [31:0]   pic_data;

        reg     sw_int, btn_int;

        wire    pps_int, rtc_int, netrx_int, nettx_int,

                auxrx_int, auxtx_int, gpio_int, flash_int, scop_int,

                gpsrx_int, sd_int, oled_int, zip_int;

        assign { zip_int, oled_int, rtc_int, sd_int,

                        nettx_int, netrx_int, scop_int, flash_int,

                        pps_int } = i_other_ints;

        //

        // The BUS Interrupt controller

        //

        icontrol #(15)  buspic(i_clk, 1'b0,

                (last_wb_stb)&&(last_wb_addr==5'h1),

                        i_wb_data, pic_data,

                { zip_int, oled_int, sd_int,

                        gpsrx_int, scop_int, flash_int, gpio_int,

                        auxtx_int, auxrx_int, nettx_int, netrx_int,

                        rtc_int, pps_int, sw_int, btn_int },

                        o_bus_int);

        // 

        // PWR Count

        // 

        // A 32-bit counter that starts at power up and never resets.  It's a

        // read only counter if you will.

        reg     [31:0]   pwr_counter;

        initial pwr_counter = 32'h00;

        always @(posedge i_clk)

                pwr_counter <= pwr_counter+32'h001;

        //

        // BTNSW

        //

        // The button and switch control register

        wire    [31:0]   w_btnsw;

        reg     [3:0]    r_sw,  swcfg,  swnow,  swlast;

        reg     [3:0]    r_btn, btncfg, btnnow, btnlast, btnstate;

        initial btn_int = 1'b0;

        initial sw_int  = 1'b0;

        always @(posedge i_clk)

        begin

                r_sw <= i_sw;

                swnow <= r_sw;

                swlast<= swnow;

                sw_int <= |((swnow^swlast)|swcfg);

                if ((last_wb_stb)&&(last_wb_addr == 5'h4))

                        swcfg <= ((last_wb_data[3:0])&(last_wb_data[11:8]))

                                        |((~last_wb_data[3:0])&(swcfg));

                r_btn <= i_btn;

                btnnow <= r_btn;

                btn_int <= |(btnnow&btncfg);

                if ((last_wb_stb)&&(last_wb_addr == 5'h4))

                begin

                        btncfg <= ((last_wb_data[7:4])&(last_wb_data[15:12]))

                                        |((~last_wb_data[7:4])&(btncfg));

                        btnstate<= (btnnow)|((btnstate)&(~last_wb_data[7:4]));

                end else

                        btnstate <= (btnstate)|(btnnow);

        end

        assign  w_btnsw = { 8'h00, btnnow, 4'h0, btncfg, swcfg, btnstate, swnow };

        //

        // LEDCTRL

        //

        reg     [3:0]    r_leds;

        wire    [31:0]   w_ledreg;

        reg     last_cyc;

        always @(posedge i_clk)

                last_cyc <= i_wb_cyc;

        initial r_leds = 4'h0;

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'h5))

                        r_leds <= ((last_wb_data[7:4])&(last_wb_data[3:0]))

                                |((~last_wb_data[7:4])&(r_leds));

        assign  o_led = r_leds;

        assign  w_ledreg = { 28'h0, r_leds  };

        //

        // GPIO

        //

        // Not used (yet), but this interface should allow us to control up to

        // 16 GPIO inputs, and another 16 GPIO outputs.  The interrupt trips

        // when any of the inputs changes.  (Sorry, which input isn't (yet)

        // selectable.)

        //

        assign  gpio_int = 1'b0;

        //

        // AUX (UART) SETUP

        //

        // Set us up for 4Mbaud, 8 data bits, no stop bits.

        reg     [29:0]   aux_setup;

        initial aux_setup = AUXUART_SETUP;

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'h6))

                        aux_setup[29:0] <= last_wb_data[29:0];

        //

        // GPSSETUP

        //

        // Set us up for 9600 kbaud, 8 data bits, no stop bits.

        reg     [29:0]   gps_setup;

        initial gps_setup = GPSUART_SETUP;

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'h7))

                        gps_setup[29:0] <= last_wb_data[29:0];

        //

        // CLR LEDs

        //

        // CLR LED 0

        wire    [31:0]   w_clr_led0;

        reg     [8:0]    r_clr_led0_r, r_clr_led0_g, r_clr_led0_b;

        initial r_clr_led0_r = 9'h003; // Color LED on the far right

        initial r_clr_led0_g = 9'h000;

        initial r_clr_led0_b = 9'h000;

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'h8))

                begin

                        r_clr_led0_r <= { last_wb_data[26], last_wb_data[23:16] };

                        r_clr_led0_g <= { last_wb_data[25], last_wb_data[15: 8] };

                        r_clr_led0_b <= { last_wb_data[24], last_wb_data[ 7: 0] };

                end

        assign  w_clr_led0 = { 5'h0,

                        r_clr_led0_r[8], r_clr_led0_g[8], r_clr_led0_b[8],

                        r_clr_led0_r[7:0], r_clr_led0_g[7:0], r_clr_led0_b[7:0]

                };

        always @(posedge i_clk)

                o_clr_led0 <= { (pwr_counter[8:0] < r_clr_led0_r),

                                (pwr_counter[8:0] < r_clr_led0_g),

                                (pwr_counter[8:0] < r_clr_led0_b) };

        // CLR LED 1

        wire    [31:0]   w_clr_led1;

        reg     [8:0]    r_clr_led1_r, r_clr_led1_g, r_clr_led1_b;

        initial r_clr_led1_r = 9'h007;

        initial r_clr_led1_g = 9'h000;

        initial r_clr_led1_b = 9'h000;

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'h9))

                begin

                        r_clr_led1_r <= { last_wb_data[26], last_wb_data[23:16] };

                        r_clr_led1_g <= { last_wb_data[25], last_wb_data[15: 8] };

                        r_clr_led1_b <= { last_wb_data[24], last_wb_data[ 7: 0] };

                end

        assign  w_clr_led1 = { 5'h0,

                        r_clr_led1_r[8], r_clr_led1_g[8], r_clr_led1_b[8],

                        r_clr_led1_r[7:0], r_clr_led1_g[7:0], r_clr_led1_b[7:0]

                };

        always @(posedge i_clk)

                o_clr_led1 <= { (pwr_counter[8:0] < r_clr_led1_r),

                                (pwr_counter[8:0] < r_clr_led1_g),

                                (pwr_counter[8:0] < r_clr_led1_b) };

        // CLR LED 0

        wire    [31:0]   w_clr_led2;

        reg     [8:0]    r_clr_led2_r, r_clr_led2_g, r_clr_led2_b;

        initial r_clr_led2_r = 9'h00f;

        initial r_clr_led2_g = 9'h000;

        initial r_clr_led2_b = 9'h000;

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'ha))

                begin

                        r_clr_led2_r <= { last_wb_data[26], last_wb_data[23:16] };

                        r_clr_led2_g <= { last_wb_data[25], last_wb_data[15: 8] };

                        r_clr_led2_b <= { last_wb_data[24], last_wb_data[ 7: 0] };

                end

        assign  w_clr_led2 = { 5'h0,

                        r_clr_led2_r[8], r_clr_led2_g[8], r_clr_led2_b[8],

                        r_clr_led2_r[7:0], r_clr_led2_g[7:0], r_clr_led2_b[7:0]

                };

        always @(posedge i_clk)

                o_clr_led2 <= { (pwr_counter[8:0] < r_clr_led2_r),

                                (pwr_counter[8:0] < r_clr_led2_g),

                                (pwr_counter[8:0] < r_clr_led2_b) };

        // CLR LED 3

        wire    [31:0]   w_clr_led3;

        reg     [8:0]    r_clr_led3_r, r_clr_led3_g, r_clr_led3_b;

        initial r_clr_led3_r = 9'h01f; // LED is on far left

        initial r_clr_led3_g = 9'h000;

        initial r_clr_led3_b = 9'h000;

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'hb))

                begin

                        r_clr_led3_r <= { last_wb_data[26], last_wb_data[23:16] };

                        r_clr_led3_g <= { last_wb_data[25], last_wb_data[15: 8] };

                        r_clr_led3_b <= { last_wb_data[24], last_wb_data[ 7: 0] };

                end

        assign  w_clr_led3 = { 5'h0,

                        r_clr_led3_r[8], r_clr_led3_g[8], r_clr_led3_b[8],

                        r_clr_led3_r[7:0], r_clr_led3_g[7:0], r_clr_led3_b[7:0]

                };

        always @(posedge i_clk)

                o_clr_led3 <= { (pwr_counter[8:0] < r_clr_led3_r),

                                (pwr_counter[8:0] < r_clr_led3_g),

                                (pwr_counter[8:0] < r_clr_led3_b) };

        //

        // The Calendar DATE

        //

        wire    [31:0]   date_data;

`define GET_DATE

`ifdef  GET_DATE

        wire    date_ack, date_stall;

        rtcdate thedate(i_clk, i_rtc_ppd,

                i_wb_cyc, last_wb_stb, (last_wb_addr==5'hc), last_wb_data,

                        date_ack, date_stall, date_data);

`else

        assign  date_data = 32'h20160000;

`endif

        //////

        //

        // The auxilliary UART

        //

        //////

        //

        // First the Auxilliary UART receiver

        //

        wire    auxrx_stb, auxrx_break, auxrx_perr, auxrx_ferr, auxck_uart;

        wire    [7:0]    rx_data_aux_port;

        rxuart  auxrx(i_clk, 1'b0, aux_setup, i_aux_rx,

                        auxrx_stb, rx_data_aux_port, auxrx_break,

                        auxrx_perr, auxrx_ferr, auxck_uart);

        wire    [31:0]   auxrx_data;

        reg     [11:0]   r_auxrx_data;

        always @(posedge i_clk)

                if (auxrx_stb)

                begin

                        r_auxrx_data[11] <= auxrx_break;

                        r_auxrx_data[10] <= auxrx_ferr;

                        r_auxrx_data[ 9] <= auxrx_perr;

                        r_auxrx_data[7:0]<= rx_data_aux_port;

                end

        always @(posedge i_clk)

                if(((i_wb_stb)&&(~i_wb_we)&&(i_wb_addr == 5'h0e))||(auxrx_stb))

                        r_auxrx_data[8] <= auxrx_stb;

        assign  o_aux_cts = auxrx_stb;

        assign  auxrx_data = { 20'h00, r_auxrx_data };

        assign  auxrx_int = r_auxrx_data[8];

        //

        // Then the auxilliary UART transmitter

        //

        wire    auxtx_busy;

        reg     [7:0]    r_auxtx_data;

        reg             r_auxtx_stb, r_auxtx_break;

        wire    [31:0]   auxtx_data;

        txuart  auxtx(i_clk, 1'b0, aux_setup,

                        r_auxtx_break, r_auxtx_stb, r_auxtx_data,

                        o_aux_tx, auxtx_busy);

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'h0f))

                begin

                        r_auxtx_stb <= 1'b1;

                        r_auxtx_data <= last_wb_data[7:0];

                        r_auxtx_break<= last_wb_data[9];

                end else if (~auxtx_busy)

                begin

                        r_auxtx_stb <= 1'b0;

                        r_auxtx_data <= 8'h0;

                end

        assign  auxtx_data = { 20'h00,

                auxck_uart, o_aux_tx, r_auxtx_break, auxtx_busy,

                r_auxtx_data };

        assign  auxtx_int = ~auxtx_busy;

        //////

        //

        // The GPS UART

        //

        //////

        // First the receiver

        wire    gpsrx_stb, gpsrx_break, gpsrx_perr, gpsrx_ferr, gpsck_uart;

        wire    [7:0]    rx_data_gps_port;

        rxuart  gpsrx(i_clk, 1'b0, gps_setup, i_gps_rx,

                        gpsrx_stb, rx_data_gps_port, gpsrx_break,

                        gpsrx_perr, gpsrx_ferr, gpsck_uart);

        wire    [31:0]   gpsrx_data;

        reg     [11:0]   r_gpsrx_data;

        always @(posedge i_clk)

                if (gpsrx_stb)

                begin

                        r_gpsrx_data[11] <= gpsrx_break;

                        r_gpsrx_data[10] <= gpsrx_ferr;

                        r_gpsrx_data[ 9] <= gpsrx_perr;

                        r_gpsrx_data[7:0]<= rx_data_gps_port;

                end

        always @(posedge i_clk)

                if(((i_wb_stb)&&(~i_wb_we)&&(i_wb_addr == 5'h10))||(gpsrx_stb))

                        r_gpsrx_data[8] <= gpsrx_stb;

        assign  gpsrx_data = { 20'h00, r_gpsrx_data };

        assign  gpsrx_int = r_gpsrx_data[8];

        // Then the transmitter

        reg             r_gpstx_break, r_gpstx_stb;

        reg     [7:0]    r_gpstx_data;

        wire            gpstx_busy;

        wire    [31:0]   gpstx_data;

        txuart  gpstx(i_clk, 1'b0, gps_setup,

                        r_gpstx_break, r_gpstx_stb, r_gpstx_data,

                        o_gps_tx, gpstx_busy);

        always @(posedge i_clk)

                if ((last_wb_stb)&&(last_wb_addr == 5'h11))

                begin

                        r_gpstx_stb <= 1'b1;

                        r_gpstx_data <= last_wb_data[7:0];

                        r_gpstx_break<= last_wb_data[9];

                end else if (~gpstx_busy)

                begin

                        r_gpstx_stb <= 1'b0;

                        r_gpstx_data <= 8'h0;

                end

        assign  gpstx_data = { 20'h00,

                gpsck_uart, o_gps_tx, r_gpstx_break, gpstx_busy,

                r_gpstx_data };

        always @(posedge i_clk)

                case(i_wb_addr)

                5'h00: o_wb_data <= `DATESTAMP;

                5'h01: o_wb_data <= pic_data;

                5'h02: o_wb_data <= i_buserr;

                5'h03: o_wb_data <= pwr_counter;

                5'h04: o_wb_data <= w_btnsw;

                5'h05: o_wb_data <= w_ledreg;

                5'h06: o_wb_data <= { 2'b00, aux_setup };

                5'h07: o_wb_data <= { 2'b00, gps_setup };

                5'h08: o_wb_data <= w_clr_led0;

                5'h09: o_wb_data <= w_clr_led1;

                5'h0a: o_wb_data <= w_clr_led2;

                5'h0b: o_wb_data <= w_clr_led3;

                5'h0c: o_wb_data <= date_data;

                // 5'h0d: o_wb_data <= gpio_data;

                5'h0e: o_wb_data <= auxrx_data;

                5'h0f: o_wb_data <= auxtx_data;

                5'h10: o_wb_data <= gpsrx_data;

                5'h11: o_wb_data <= gpstx_data;

                // 5'hf: UART_SETUP

                // 4'h6: GPIO

                // ?? : GPS-UARTRX

                // ?? : GPS-UARTTX

                default: o_wb_data <= 32'h00;

                endcase

        assign  o_wb_stall = 1'b0;

        always @(posedge i_clk)

                o_wb_ack <= (i_wb_stb);

        assign  o_board_ints = { gpio_int, auxrx_int, auxtx_int, gpsrx_int, sw_int, btn_int };

endmodule