| 1 |
3 |
dgisselq |
////////////////////////////////////////////////////////////////////////////////
|
| 2 |
|
|
//
|
| 3 |
|
|
// Filename: wbuidleint.v
|
| 4 |
|
|
//
|
| 5 |
|
|
// Project: FPGA library
|
| 6 |
|
|
//
|
| 7 |
|
|
// Purpose: Creates an output for the interface, inserting idle words and
|
| 8 |
|
|
// words indicating an interrupt has taken place into the output
|
| 9 |
|
|
// stream. Henceforth, the output means more than just bus transaction
|
| 10 |
|
|
// results. It may mean there is no bus transaction result to report,
|
| 11 |
|
|
// or that an interrupt has taken place.
|
| 12 |
|
|
//
|
| 13 |
|
|
//
|
| 14 |
|
|
// Creator: Dan Gisselquist, Ph.D.
|
| 15 |
|
|
// Gisselquist Technology, LLC
|
| 16 |
|
|
//
|
| 17 |
|
|
////////////////////////////////////////////////////////////////////////////////
|
| 18 |
|
|
//
|
| 19 |
|
|
// Copyright (C) 2015-2016, Gisselquist Technology, LLC
|
| 20 |
|
|
//
|
| 21 |
|
|
// This program is free software (firmware): you can redistribute it and/or
|
| 22 |
|
|
// modify it under the terms of the GNU General Public License as published
|
| 23 |
|
|
// by the Free Software Foundation, either version 3 of the License, or (at
|
| 24 |
|
|
// your option) any later version.
|
| 25 |
|
|
//
|
| 26 |
|
|
// This program is distributed in the hope that it will be useful, but WITHOUT
|
| 27 |
|
|
// ANY WARRANTY; without even the implied warranty of MERCHANTIBILITY or
|
| 28 |
|
|
// FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
|
| 29 |
|
|
// for more details.
|
| 30 |
|
|
//
|
| 31 |
|
|
// License: GPL, v3, as defined and found on www.gnu.org,
|
| 32 |
|
|
// http://www.gnu.org/licenses/gpl.html
|
| 33 |
|
|
//
|
| 34 |
|
|
//
|
| 35 |
|
|
////////////////////////////////////////////////////////////////////////////////
|
| 36 |
|
|
//
|
| 37 |
|
|
//
|
| 38 |
|
|
module wbuidleint(i_clk, i_stb, i_codword, i_cyc, i_busy, i_int,
|
| 39 |
|
|
o_stb, o_codword, o_busy,
|
| 40 |
|
|
i_tx_busy);
|
| 41 |
|
|
input i_clk;
|
| 42 |
|
|
// From the FIFO following the bus executor
|
| 43 |
|
|
input i_stb;
|
| 44 |
|
|
input [35:0] i_codword;
|
| 45 |
|
|
// From the rest of the board
|
| 46 |
|
|
input i_cyc, i_busy, i_int;
|
| 47 |
|
|
// To the next stage
|
| 48 |
|
|
output reg o_stb;
|
| 49 |
|
|
output reg [35:0] o_codword;
|
| 50 |
|
|
output reg o_busy;
|
| 51 |
|
|
// Is the next stage busy?
|
| 52 |
|
|
input i_tx_busy;
|
| 53 |
|
|
|
| 54 |
|
|
reg int_request, int_sent;
|
| 55 |
|
|
initial int_request = 1'b0;
|
| 56 |
|
|
always @(posedge i_clk)
|
| 57 |
|
|
if((o_stb)&&(~i_tx_busy)&&(o_codword[35:30]==6'h4))
|
| 58 |
|
|
int_request <= i_int;
|
| 59 |
|
|
else
|
| 60 |
|
|
int_request <= (int_request)||(i_int);
|
| 61 |
|
|
|
| 62 |
|
|
|
| 63 |
|
|
// Now, for the idle counter
|
| 64 |
|
|
wire idle_expired;
|
| 65 |
|
|
reg idle_state;
|
| 66 |
|
|
reg [35:0] idle_counter;
|
| 67 |
|
|
initial idle_counter = 36'h0000;
|
| 68 |
|
|
always @(posedge i_clk)
|
| 69 |
|
|
if ((i_stb)||(o_stb))
|
| 70 |
|
|
idle_counter <= 36'h000;
|
| 71 |
|
|
else if (~idle_counter[35])
|
| 72 |
|
|
idle_counter <= idle_counter + 36'd43;
|
| 73 |
|
|
|
| 74 |
|
|
initial idle_state = 1'b0;
|
| 75 |
|
|
always @(posedge i_clk)
|
| 76 |
|
|
if ((o_stb)&&(~i_tx_busy)&&(o_codword[35:31]==5'h0))
|
| 77 |
|
|
idle_state <= 1'b1;
|
| 78 |
|
|
else if (~idle_counter[35])
|
| 79 |
|
|
idle_state <= 1'b0;
|
| 80 |
|
|
|
| 81 |
|
|
assign idle_expired = (~idle_state)&&(idle_counter[35]);
|
| 82 |
|
|
|
| 83 |
|
|
initial o_stb = 1'b0;
|
| 84 |
|
|
initial o_busy = 1'b0;
|
| 85 |
|
|
always @(posedge i_clk)
|
| 86 |
|
|
if ((o_stb)&&(i_tx_busy))
|
| 87 |
|
|
begin
|
| 88 |
|
|
o_busy <= 1'b1;
|
| 89 |
|
|
end else if (o_stb) // and not i_tx_busy
|
| 90 |
|
|
begin
|
| 91 |
|
|
// Idle one clock before becoming not busy
|
| 92 |
|
|
o_stb <= 1'b0;
|
| 93 |
|
|
o_busy <= 1'b1;
|
| 94 |
|
|
end else if (o_busy)
|
| 95 |
|
|
o_busy <= 1'b0;
|
| 96 |
|
|
else if (i_stb) // and (~o_busy)&&(~o_stb)
|
| 97 |
|
|
begin // On a valid output, just send it out
|
| 98 |
|
|
// We'll open this strobe, even if the transmitter
|
| 99 |
|
|
// is busy, just 'cause we might otherwise lose it
|
| 100 |
|
|
o_codword <= i_codword;
|
| 101 |
|
|
o_stb <= 1'b1;
|
| 102 |
|
|
o_busy <= 1'b1;
|
| 103 |
|
|
end else if ((int_request)&&(~int_sent))
|
| 104 |
|
|
begin
|
| 105 |
|
|
o_stb <= 1'b1;
|
| 106 |
|
|
o_codword <= { 6'h4, 30'h0000 }; // interrupt codeword
|
| 107 |
|
|
o_busy <= 1'b1;
|
| 108 |
|
|
end else if (idle_expired)
|
| 109 |
|
|
begin // Strobe, if we're not writing or our
|
| 110 |
|
|
// last command wasn't an idle
|
| 111 |
|
|
o_stb <= 1'b1;
|
| 112 |
|
|
o_busy <= 1'b1;
|
| 113 |
|
|
if (i_cyc)
|
| 114 |
|
|
o_codword <= { 6'h1, 30'h0000 }; // idle codeword, bus busy
|
| 115 |
|
|
else
|
| 116 |
|
|
o_codword <= { 6'h0, 30'h0000 };
|
| 117 |
|
|
end
|
| 118 |
|
|
|
| 119 |
|
|
initial int_sent = 1'b0;
|
| 120 |
|
|
always @(posedge i_clk)
|
| 121 |
|
|
if ((int_request)&&((~o_stb)&&(~o_busy)&&(~i_stb)))
|
| 122 |
|
|
int_sent <= 1'b1;
|
| 123 |
|
|
else if (~i_int)
|
| 124 |
|
|
int_sent <= 1'b0;
|
| 125 |
|
|
endmodule
|
