Subversion Repositories openmsp430

//----------------------------------------------------------------------------

// Copyright (C) 2009 , Olivier Girard

//

// Redistribution and use in source and binary forms, with or without

// modification, are permitted provided that the following conditions

// are met:

//     * Redistributions of source code must retain the above copyright

//       notice, this list of conditions and the following disclaimer.

//     * Redistributions in binary form must reproduce the above copyright

//       notice, this list of conditions and the following disclaimer in the

//       documentation and/or other materials provided with the distribution.

//     * Neither the name of the authors nor the names of its contributors

//       may be used to endorse or promote products derived from this software

//       without specific prior written permission.

//

// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE

// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF

// THE POSSIBILITY OF SUCH DAMAGE

//

//----------------------------------------------------------------------------

//

// *File Name: openMSP430.v

//

// *Module Description:

//                       openMSP430 Top level file

//

// *Author(s):

//              - Olivier Girard,    olgirard@gmail.com

//

//----------------------------------------------------------------------------

// $Rev: 103 $

// $LastChangedBy: olivier.girard $

// $LastChangedDate: 2011-03-05 15:44:48 +0100 (Sat, 05 Mar 2011) $

//----------------------------------------------------------------------------

`ifdef OMSP_NO_INCLUDE

`else

`include "openMSP430_defines.v"

`endif

module  openMSP430 (

// OUTPUTs

    aclk,                                    // ASIC ONLY: ACLK

    aclk_en,                                 // FPGA ONLY: ACLK enable

    dbg_freeze,                              // Freeze peripherals

    dbg_i2c_sda_out,                         // Debug interface: I2C SDA OUT

    dbg_uart_txd,                            // Debug interface: UART TXD

    dco_enable,                              // ASIC ONLY: Fast oscillator enable

    dco_wkup,                                // ASIC ONLY: Fast oscillator wake-up (asynchronous)

    dmem_addr,                               // Data Memory address

    dmem_cen,                                // Data Memory chip enable (low active)

    dmem_din,                                // Data Memory data input

    dmem_wen,                                // Data Memory write byte enable (low active)

    irq_acc,                                 // Interrupt request accepted (one-hot signal)

    lfxt_enable,                             // ASIC ONLY: Low frequency oscillator enable

    lfxt_wkup,                               // ASIC ONLY: Low frequency oscillator wake-up (asynchronous)

    mclk,                                    // Main system clock

    dma_dout,                                // Direct Memory Access data output

    dma_ready,                               // Direct Memory Access is complete

    dma_resp,                                // Direct Memory Access response (0:Okay / 1:Error)

    per_addr,                                // Peripheral address

    per_din,                                 // Peripheral data input

    per_en,                                  // Peripheral enable (high active)

    per_we,                                  // Peripheral write byte enable (high active)

    pmem_addr,                               // Program Memory address

    pmem_cen,                                // Program Memory chip enable (low active)

    pmem_din,                                // Program Memory data input (optional)

    pmem_wen,                                // Program Memory write byte enable (low active) (optional)

    puc_rst,                                 // Main system reset

    smclk,                                   // ASIC ONLY: SMCLK

    smclk_en,                                // FPGA ONLY: SMCLK enable

// INPUTs

    cpu_en,                                  // Enable CPU code execution (asynchronous and non-glitchy)

    dbg_en,                                  // Debug interface enable (asynchronous and non-glitchy)

    dbg_i2c_addr,                            // Debug interface: I2C Address

    dbg_i2c_broadcast,                       // Debug interface: I2C Broadcast Address (for multicore systems)

    dbg_i2c_scl,                             // Debug interface: I2C SCL

    dbg_i2c_sda_in,                          // Debug interface: I2C SDA IN

    dbg_uart_rxd,                            // Debug interface: UART RXD (asynchronous)

    dco_clk,                                 // Fast oscillator (fast clock)

    dmem_dout,                               // Data Memory data output

    irq,                                     // Maskable interrupts

    lfxt_clk,                                // Low frequency oscillator (typ 32kHz)

    dma_addr,                                // Direct Memory Access address

    dma_din,                                 // Direct Memory Access data input

    dma_en,                                  // Direct Memory Access enable (high active)

    dma_priority,                            // Direct Memory Access priority (0:low / 1:high)

    dma_we,                                  // Direct Memory Access write byte enable (high active)

    dma_wkup,                                // ASIC ONLY: DMA Sub-System Wake-up (asynchronous and non-glitchy)

    nmi,                                     // Non-maskable interrupt (asynchronous)

    per_dout,                                // Peripheral data output

    pmem_dout,                               // Program Memory data output

    reset_n,                                 // Reset Pin (low active, asynchronous and non-glitchy)

    scan_enable,                             // ASIC ONLY: Scan enable (active during scan shifting)

    scan_mode,                               // ASIC ONLY: Scan mode

    wkup                                     // ASIC ONLY: System Wake-up (asynchronous and non-glitchy)

);

// PARAMETERs

//============

parameter            INST_NR  = 8'h00;       // Current oMSP instance number     (for multicore systems)

parameter            TOTAL_NR = 8'h00;       // Total number of oMSP instances-1 (for multicore systems)

// OUTPUTs

//============

output               aclk;                   // ASIC ONLY: ACLK

output               aclk_en;                // FPGA ONLY: ACLK enable

output               dbg_freeze;             // Freeze peripherals

output               dbg_i2c_sda_out;        // Debug interface: I2C SDA OUT

output               dbg_uart_txd;           // Debug interface: UART TXD

output               dco_enable;             // ASIC ONLY: Fast oscillator enable

output               dco_wkup;               // ASIC ONLY: Fast oscillator wake-up (asynchronous)

output [`DMEM_MSB:0] dmem_addr;              // Data Memory address

output               dmem_cen;               // Data Memory chip enable (low active)

output        [15:0] dmem_din;               // Data Memory data input

output         [1:0] dmem_wen;               // Data Memory write byte enable (low active)

output [`IRQ_NR-3:0] irq_acc;                // Interrupt request accepted (one-hot signal)

output               lfxt_enable;            // ASIC ONLY: Low frequency oscillator enable

output               lfxt_wkup;              // ASIC ONLY: Low frequency oscillator wake-up (asynchronous)

output               mclk;                   // Main system clock

output        [15:0] dma_dout;               // Direct Memory Access data output

output               dma_ready;              // Direct Memory Access is complete

output               dma_resp;               // Direct Memory Access response (0:Okay / 1:Error)

output        [13:0] per_addr;               // Peripheral address

output        [15:0] per_din;                // Peripheral data input

output               per_en;                 // Peripheral enable (high active)

output         [1:0] per_we;                 // Peripheral write byte enable (high active)

output [`PMEM_MSB:0] pmem_addr;              // Program Memory address

output               pmem_cen;               // Program Memory chip enable (low active)

output        [15:0] pmem_din;               // Program Memory data input (optional)

output         [1:0] pmem_wen;               // Program Memory write enable (low active) (optional)

output               puc_rst;                // Main system reset

output               smclk;                  // ASIC ONLY: SMCLK

output               smclk_en;               // FPGA ONLY: SMCLK enable

// INPUTs

//============

input                cpu_en;                 // Enable CPU code execution (asynchronous and non-glitchy)

input                dbg_en;                 // Debug interface enable (asynchronous and non-glitchy)

input          [6:0] dbg_i2c_addr;           // Debug interface: I2C Address

input          [6:0] dbg_i2c_broadcast;      // Debug interface: I2C Broadcast Address (for multicore systems)

input                dbg_i2c_scl;            // Debug interface: I2C SCL

input                dbg_i2c_sda_in;         // Debug interface: I2C SDA IN

input                dbg_uart_rxd;           // Debug interface: UART RXD (asynchronous)

input                dco_clk;                // Fast oscillator (fast clock)

input         [15:0] dmem_dout;              // Data Memory data output

input  [`IRQ_NR-3:0] irq;                    // Maskable interrupts (14, 30 or 62)

input                lfxt_clk;               // Low frequency oscillator (typ 32kHz)

input         [15:1] dma_addr;               // Direct Memory Access address

input         [15:0] dma_din;                // Direct Memory Access data input

input                dma_en;                 // Direct Memory Access enable (high active)

input                dma_priority;           // Direct Memory Access priority (0:low / 1:high)

input          [1:0] dma_we;                 // Direct Memory Access write byte enable (high active)

input                dma_wkup;               // ASIC ONLY: DMA Wake-up (asynchronous and non-glitchy)

input                nmi;                    // Non-maskable interrupt (asynchronous and non-glitchy)

input         [15:0] per_dout;               // Peripheral data output

input         [15:0] pmem_dout;              // Program Memory data output

input                reset_n;                // Reset Pin (active low, asynchronous and non-glitchy)

input                scan_enable;            // ASIC ONLY: Scan enable (active during scan shifting)

input                scan_mode;              // ASIC ONLY: Scan mode

input                wkup;                   // ASIC ONLY: System Wake-up (asynchronous and non-glitchy)

//=============================================================================

// 1)  INTERNAL WIRES/REGISTERS/PARAMETERS DECLARATION

//=============================================================================

wire           [7:0] inst_ad;

wire           [7:0] inst_as;

wire          [11:0] inst_alu;

wire                 inst_bw;

wire                 inst_irq_rst;

wire                 inst_mov;

wire          [15:0] inst_dest;

wire          [15:0] inst_dext;

wire          [15:0] inst_sext;

wire           [7:0] inst_so;

wire          [15:0] inst_src;

wire           [2:0] inst_type;

wire           [7:0] inst_jmp;

wire           [3:0] e_state;

wire                 exec_done;

wire                 decode_noirq;

wire                 cpu_en_s;

wire                 cpuoff;

wire                 oscoff;

wire                 scg0;

wire                 scg1;

wire                 por;

wire                 gie;

wire                 cpu_mclk;

wire                 dma_mclk;

wire                 mclk_dma_enable;

wire                 mclk_dma_wkup;

wire                 mclk_enable;

wire                 mclk_wkup;

wire          [31:0] cpu_id;

wire           [7:0] cpu_nr_inst  = INST_NR;

wire           [7:0] cpu_nr_total = TOTAL_NR;

wire          [15:0] eu_mab;

wire          [15:0] eu_mdb_in;

wire          [15:0] eu_mdb_out;

wire           [1:0] eu_mb_wr;

wire                 eu_mb_en;

wire          [15:0] fe_mab;

wire          [15:0] fe_mdb_in;

wire                 fe_mb_en;

wire                 fe_pmem_wait;

wire                 pc_sw_wr;

wire          [15:0] pc_sw;

wire          [15:0] pc;

wire          [15:0] pc_nxt;

wire                 nmi_acc;

wire                 nmi_pnd;

wire                 nmi_wkup;

wire                 wdtie;

wire                 wdtnmies;

wire                 wdtifg;

wire                 wdt_irq;

wire                 wdt_wkup;

wire                 wdt_reset;

wire                 wdtifg_sw_clr;

wire                 wdtifg_sw_set;

wire                 dbg_clk;

wire                 dbg_rst;

wire                 dbg_en_s;

wire                 dbg_halt_cmd;

wire                 dbg_mem_en;

wire                 dbg_reg_wr;

wire                 dbg_cpu_reset;

wire          [15:0] dbg_mem_addr;

wire          [15:0] dbg_mem_dout;

wire          [15:0] dbg_mem_din;

wire          [15:0] dbg_reg_din;

wire           [1:0] dbg_mem_wr;

wire                 cpu_halt_st;

wire                 cpu_halt_cmd;

wire                 puc_pnd_set;

wire          [15:0] per_dout_or;

wire          [15:0] per_dout_sfr;

wire          [15:0] per_dout_wdog;

wire          [15:0] per_dout_mpy;

wire          [15:0] per_dout_clk;

//=============================================================================

// 2)  GLOBAL CLOCK & RESET MANAGEMENT

//=============================================================================

omsp_clock_module clock_module_0 (

// OUTPUTs

    .aclk              (aclk),               // ACLK

    .aclk_en           (aclk_en),            // ACLK enablex

    .cpu_en_s          (cpu_en_s),           // Enable CPU code execution (synchronous)

    .cpu_mclk          (cpu_mclk),           // Main system CPU only clock

    .dma_mclk          (dma_mclk),           // Main system DMA and/or CPU clock

    .dbg_clk           (dbg_clk),            // Debug unit clock

    .dbg_en_s          (dbg_en_s),           // Debug interface enable (synchronous)

    .dbg_rst           (dbg_rst),            // Debug unit reset

    .dco_enable        (dco_enable),         // Fast oscillator enable

    .dco_wkup          (dco_wkup),           // Fast oscillator wake-up (asynchronous)

    .lfxt_enable       (lfxt_enable),        // Low frequency oscillator enable

    .lfxt_wkup         (lfxt_wkup),          // Low frequency oscillator wake-up (asynchronous)

    .per_dout          (per_dout_clk),       // Peripheral data output

    .por               (por),                // Power-on reset

    .puc_pnd_set       (puc_pnd_set),        // PUC pending set for the serial debug interface

    .puc_rst           (puc_rst),            // Main system reset

    .smclk             (smclk),              // SMCLK

    .smclk_en          (smclk_en),           // SMCLK enable

// INPUTs

    .cpu_en            (cpu_en),             // Enable CPU code execution (asynchronous)

    .cpuoff            (cpuoff),             // Turns off the CPU

    .dbg_cpu_reset     (dbg_cpu_reset),      // Reset CPU from debug interface

    .dbg_en            (dbg_en),             // Debug interface enable (asynchronous)

    .dco_clk           (dco_clk),            // Fast oscillator (fast clock)

    .lfxt_clk          (lfxt_clk),           // Low frequency oscillator (typ 32kHz)

    .mclk_dma_enable   (mclk_dma_enable),    // DMA Sub-System Clock enable

    .mclk_dma_wkup     (mclk_dma_wkup),      // DMA Sub-System Clock wake-up (asynchronous)

    .mclk_enable       (mclk_enable),        // Main System Clock enable

    .mclk_wkup         (mclk_wkup),          // Main System Clock wake-up (asynchronous)

    .oscoff            (oscoff),             // Turns off LFXT1 clock input

    .per_addr          (per_addr),           // Peripheral address

    .per_din           (per_din),            // Peripheral data input

    .per_en            (per_en),             // Peripheral enable (high active)

    .per_we            (per_we),             // Peripheral write enable (high active)

    .reset_n           (reset_n),            // Reset Pin (low active, asynchronous)

    .scan_enable       (scan_enable),        // Scan enable (active during scan shifting)

    .scan_mode         (scan_mode),          // Scan mode

    .scg0              (scg0),               // System clock generator 1. Turns off the DCO

    .scg1              (scg1),               // System clock generator 1. Turns off the SMCLK

    .wdt_reset         (wdt_reset)           // Watchdog-timer reset

);

assign mclk = dma_mclk;

//=============================================================================

// 3)  FRONTEND (<=> FETCH & DECODE)

//=============================================================================

omsp_frontend frontend_0 (

// OUTPUTs

    .cpu_halt_st       (cpu_halt_st),        // Halt/Run status from CPU

    .decode_noirq      (decode_noirq),       // Frontend decode instruction

    .e_state           (e_state),            // Execution state

    .exec_done         (exec_done),          // Execution completed

    .inst_ad           (inst_ad),            // Decoded Inst: destination addressing mode

    .inst_as           (inst_as),            // Decoded Inst: source addressing mode

    .inst_alu          (inst_alu),           // ALU control signals

    .inst_bw           (inst_bw),            // Decoded Inst: byte width

    .inst_dest         (inst_dest),          // Decoded Inst: destination (one hot)

    .inst_dext         (inst_dext),          // Decoded Inst: destination extended instruction word

    .inst_irq_rst      (inst_irq_rst),       // Decoded Inst: Reset interrupt

    .inst_jmp          (inst_jmp),           // Decoded Inst: Conditional jump

    .inst_mov          (inst_mov),           // Decoded Inst: mov instruction

    .inst_sext         (inst_sext),          // Decoded Inst: source extended instruction word

    .inst_so           (inst_so),            // Decoded Inst: Single-operand arithmetic

    .inst_src          (inst_src),           // Decoded Inst: source (one hot)

    .inst_type         (inst_type),          // Decoded Instruction type

    .irq_acc           (irq_acc),            // Interrupt request accepted

    .mab               (fe_mab),             // Frontend Memory address bus

    .mb_en             (fe_mb_en),           // Frontend Memory bus enable

    .mclk_dma_enable   (mclk_dma_enable),    // DMA Sub-System Clock enable

    .mclk_dma_wkup     (mclk_dma_wkup),      // DMA Sub-System Clock wake-up (asynchronous)

    .mclk_enable       (mclk_enable),        // Main System Clock enable

    .mclk_wkup         (mclk_wkup),          // Main System Clock wake-up (asynchronous)

    .nmi_acc           (nmi_acc),            // Non-Maskable interrupt request accepted

    .pc                (pc),                 // Program counter

    .pc_nxt            (pc_nxt),             // Next PC value (for CALL & IRQ)

// INPUTs

    .cpu_en_s          (cpu_en_s),           // Enable CPU code execution (synchronous)

    .cpu_halt_cmd      (cpu_halt_cmd),       // Halt CPU command

    .cpuoff            (cpuoff),             // Turns off the CPU

    .dbg_reg_sel       (dbg_mem_addr[3:0]),  // Debug selected register for rd/wr access

    .dma_en            (dma_en),             // Direct Memory Access enable (high active)

    .dma_wkup          (dma_wkup),           // DMA Sub-System Wake-up (asynchronous and non-glitchy)

    .fe_pmem_wait      (fe_pmem_wait),       // Frontend wait for Instruction fetch

    .gie               (gie),                // General interrupt enable

    .irq               (irq),                // Maskable interrupts

    .mclk              (cpu_mclk),           // Main system clock

    .mdb_in            (fe_mdb_in),          // Frontend Memory data bus input

    .nmi_pnd           (nmi_pnd),            // Non-maskable interrupt pending

    .nmi_wkup          (nmi_wkup),           // NMI Wakeup

    .pc_sw             (pc_sw),              // Program counter software value

    .pc_sw_wr          (pc_sw_wr),           // Program counter software write

    .puc_rst           (puc_rst),            // Main system reset

    .scan_enable       (scan_enable),        // Scan enable (active during scan shifting)

    .wdt_irq           (wdt_irq),            // Watchdog-timer interrupt

    .wdt_wkup          (wdt_wkup),           // Watchdog Wakeup

    .wkup              (wkup)                // System Wake-up (asynchronous)

);

//=============================================================================

// 4)  EXECUTION UNIT

//=============================================================================

omsp_execution_unit execution_unit_0 (

// OUTPUTs

    .cpuoff            (cpuoff),             // Turns off the CPU

    .dbg_reg_din       (dbg_reg_din),        // Debug unit CPU register data input

    .mab               (eu_mab),             // Memory address bus

    .mb_en             (eu_mb_en),           // Memory bus enable

    .mb_wr             (eu_mb_wr),           // Memory bus write transfer

    .mdb_out           (eu_mdb_out),         // Memory data bus output

    .oscoff            (oscoff),             // Turns off LFXT1 clock input

    .pc_sw             (pc_sw),              // Program counter software value

    .pc_sw_wr          (pc_sw_wr),           // Program counter software write

    .scg0              (scg0),               // System clock generator 1. Turns off the DCO

    .scg1              (scg1),               // System clock generator 1. Turns off the SMCLK

// INPUTs

    .dbg_halt_st       (cpu_halt_st),        // Halt/Run status from CPU

    .dbg_mem_dout      (dbg_mem_dout),       // Debug unit data output

    .dbg_reg_wr        (dbg_reg_wr),         // Debug unit CPU register write

    .e_state           (e_state),            // Execution state

    .exec_done         (exec_done),          // Execution completed

    .gie               (gie),                // General interrupt enable

    .inst_ad           (inst_ad),            // Decoded Inst: destination addressing mode

    .inst_as           (inst_as),            // Decoded Inst: source addressing mode

    .inst_alu          (inst_alu),           // ALU control signals

    .inst_bw           (inst_bw),            // Decoded Inst: byte width

    .inst_dest         (inst_dest),          // Decoded Inst: destination (one hot)

    .inst_dext         (inst_dext),          // Decoded Inst: destination extended instruction word

    .inst_irq_rst      (inst_irq_rst),       // Decoded Inst: reset interrupt

    .inst_jmp          (inst_jmp),           // Decoded Inst: Conditional jump

    .inst_mov          (inst_mov),           // Decoded Inst: mov instruction

    .inst_sext         (inst_sext),          // Decoded Inst: source extended instruction word

    .inst_so           (inst_so),            // Decoded Inst: Single-operand arithmetic

    .inst_src          (inst_src),           // Decoded Inst: source (one hot)

    .inst_type         (inst_type),          // Decoded Instruction type

    .mclk              (cpu_mclk),           // Main system clock

    .mdb_in            (eu_mdb_in),          // Memory data bus input

    .pc                (pc),                 // Program counter

    .pc_nxt            (pc_nxt),             // Next PC value (for CALL & IRQ)

    .puc_rst           (puc_rst),            // Main system reset

    .scan_enable       (scan_enable)         // Scan enable (active during scan shifting)

);

//=============================================================================

// 5)  MEMORY BACKBONE

//=============================================================================

omsp_mem_backbone mem_backbone_0 (

// OUTPUTs

    .cpu_halt_cmd      (cpu_halt_cmd),       // Halt CPU command

    .dbg_mem_din       (dbg_mem_din),        // Debug unit Memory data input

    .dmem_addr         (dmem_addr),          // Data Memory address

    .dmem_cen          (dmem_cen),           // Data Memory chip enable (low active)

    .dmem_din          (dmem_din),           // Data Memory data input

    .dmem_wen          (dmem_wen),           // Data Memory write enable (low active)

    .eu_mdb_in         (eu_mdb_in),          // Execution Unit Memory data bus input

    .fe_mdb_in         (fe_mdb_in),          // Frontend Memory data bus input

    .fe_pmem_wait      (fe_pmem_wait),       // Frontend wait for Instruction fetch

    .dma_dout          (dma_dout),           // Direct Memory Access data output

    .dma_ready         (dma_ready),          // Direct Memory Access is complete

    .dma_resp          (dma_resp),           // Direct Memory Access response (0:Okay / 1:Error)

    .per_addr          (per_addr),           // Peripheral address

    .per_din           (per_din),            // Peripheral data input

    .per_we            (per_we),             // Peripheral write enable (high active)

    .per_en            (per_en),             // Peripheral enable (high active)

    .pmem_addr         (pmem_addr),          // Program Memory address

    .pmem_cen          (pmem_cen),           // Program Memory chip enable (low active)

    .pmem_din          (pmem_din),           // Program Memory data input (optional)

    .pmem_wen          (pmem_wen),           // Program Memory write enable (low active) (optional)

// INPUTs

    .cpu_halt_st       (cpu_halt_st),        // Halt/Run status from CPU

    .dbg_halt_cmd      (dbg_halt_cmd),       // Debug interface Halt CPU command

    .dbg_mem_addr      (dbg_mem_addr[15:1]), // Debug address for rd/wr access

    .dbg_mem_dout      (dbg_mem_dout),       // Debug unit data output

    .dbg_mem_en        (dbg_mem_en),         // Debug unit memory enable

    .dbg_mem_wr        (dbg_mem_wr),         // Debug unit memory write

    .dmem_dout         (dmem_dout),          // Data Memory data output

    .eu_mab            (eu_mab[15:1]),       // Execution Unit Memory address bus

    .eu_mb_en          (eu_mb_en),           // Execution Unit Memory bus enable

    .eu_mb_wr          (eu_mb_wr),           // Execution Unit Memory bus write transfer

    .eu_mdb_out        (eu_mdb_out),         // Execution Unit Memory data bus output

    .fe_mab            (fe_mab[15:1]),       // Frontend Memory address bus

    .fe_mb_en          (fe_mb_en),           // Frontend Memory bus enable

    .mclk              (dma_mclk),           // Main system clock

    .dma_addr          (dma_addr),           // Direct Memory Access address

    .dma_din           (dma_din),            // Direct Memory Access data input

    .dma_en            (dma_en),             // Direct Memory Access enable (high active)

    .dma_priority      (dma_priority),       // Direct Memory Access priority (0:low / 1:high)

    .dma_we            (dma_we),             // Direct Memory Access write byte enable (high active)

    .per_dout          (per_dout_or),        // Peripheral data output

    .pmem_dout         (pmem_dout),          // Program Memory data output

    .puc_rst           (puc_rst),            // Main system reset

    .scan_enable       (scan_enable)         // Scan enable (active during scan shifting)

);

wire UNUSED_fe_mab_0 = fe_mab[0];

//=============================================================================

// 6)  SPECIAL FUNCTION REGISTERS

//=============================================================================

omsp_sfr sfr_0 (

// OUTPUTs

    .cpu_id            (cpu_id),             // CPU ID

    .nmi_pnd           (nmi_pnd),            // NMI Pending

    .nmi_wkup          (nmi_wkup),           // NMI Wakeup

    .per_dout          (per_dout_sfr),       // Peripheral data output

    .wdtie             (wdtie),              // Watchdog-timer interrupt enable

    .wdtifg_sw_clr     (wdtifg_sw_clr),      // Watchdog-timer interrupt flag software clear

    .wdtifg_sw_set     (wdtifg_sw_set),      // Watchdog-timer interrupt flag software set

// INPUTs

    .cpu_nr_inst       (cpu_nr_inst),        // Current oMSP instance number

    .cpu_nr_total      (cpu_nr_total),       // Total number of oMSP instances-1

    .mclk              (dma_mclk),           // Main system clock

    .nmi               (nmi),                // Non-maskable interrupt (asynchronous)

    .nmi_acc           (nmi_acc),            // Non-Maskable interrupt request accepted

    .per_addr          (per_addr),           // Peripheral address

    .per_din           (per_din),            // Peripheral data input

    .per_en            (per_en),             // Peripheral enable (high active)

    .per_we            (per_we),             // Peripheral write enable (high active)

    .puc_rst           (puc_rst),            // Main system reset

    .scan_mode         (scan_mode),          // Scan mode

    .wdtifg            (wdtifg),             // Watchdog-timer interrupt flag

    .wdtnmies          (wdtnmies)            // Watchdog-timer NMI edge selection

);

//=============================================================================

// 7)  WATCHDOG TIMER

//=============================================================================

`ifdef WATCHDOG

omsp_watchdog watchdog_0 (

// OUTPUTs

    .per_dout          (per_dout_wdog),      // Peripheral data output

    .wdt_irq           (wdt_irq),            // Watchdog-timer interrupt

    .wdt_reset         (wdt_reset),          // Watchdog-timer reset

    .wdt_wkup          (wdt_wkup),           // Watchdog Wakeup

    .wdtifg            (wdtifg),             // Watchdog-timer interrupt flag

    .wdtnmies          (wdtnmies),           // Watchdog-timer NMI edge selection

// INPUTs

    .aclk              (aclk),               // ACLK

    .aclk_en           (aclk_en),            // ACLK enable

    .dbg_freeze        (dbg_freeze),         // Freeze Watchdog counter

    .mclk              (dma_mclk),           // Main system clock

    .per_addr          (per_addr),           // Peripheral address

    .per_din           (per_din),            // Peripheral data input

    .per_en            (per_en),             // Peripheral enable (high active)

    .per_we            (per_we),             // Peripheral write enable (high active)

    .por               (por),                // Power-on reset

    .puc_rst           (puc_rst),            // Main system reset

    .scan_enable       (scan_enable),        // Scan enable (active during scan shifting)

    .scan_mode         (scan_mode),          // Scan mode

    .smclk             (smclk),              // SMCLK

    .smclk_en          (smclk_en),           // SMCLK enable

    .wdtie             (wdtie),              // Watchdog-timer interrupt enable

    .wdtifg_irq_clr    (irq_acc[`IRQ_NR-6]), // Clear Watchdog-timer interrupt flag

    .wdtifg_sw_clr     (wdtifg_sw_clr),      // Watchdog-timer interrupt flag software clear

    .wdtifg_sw_set     (wdtifg_sw_set)       // Watchdog-timer interrupt flag software set

);

`else

assign per_dout_wdog        = 16'h0000;

assign wdt_irq              =  1'b0;

assign wdt_reset            =  1'b0;

assign wdt_wkup             =  1'b0;

assign wdtifg               =  1'b0;

assign wdtnmies             =  1'b0;

wire   UNUSED_por           =  por;

wire   UNUSED_wdtie         =  wdtie;

wire   UNUSED_wdtifg_sw_clr =  wdtifg_sw_clr;

wire   UNUSED_wdtifg_sw_set =  wdtifg_sw_set;

`endif

//=============================================================================

// 8)  HARDWARE MULTIPLIER

//=============================================================================

`ifdef MULTIPLIER

omsp_multiplier multiplier_0 (

// OUTPUTs

    .per_dout          (per_dout_mpy),       // Peripheral data output

// INPUTs

    .mclk              (dma_mclk),           // Main system clock

    .per_addr          (per_addr),           // Peripheral address

    .per_din           (per_din),            // Peripheral data input

    .per_en            (per_en),             // Peripheral enable (high active)

    .per_we            (per_we),             // Peripheral write enable (high active)

    .puc_rst           (puc_rst),            // Main system reset

    .scan_enable       (scan_enable)         // Scan enable (active during scan shifting)

);

`else

assign per_dout_mpy = 16'h0000;

`endif

//=============================================================================

// 9)  PERIPHERALS' OUTPUT BUS

//=============================================================================

assign  per_dout_or  =  per_dout      |

                        per_dout_clk  |

                        per_dout_sfr  |

                        per_dout_wdog |

                        per_dout_mpy;

//=============================================================================

// 10)  DEBUG INTERFACE

//=============================================================================

`ifdef DBG_EN

omsp_dbg dbg_0 (

// OUTPUTs

    .dbg_cpu_reset     (dbg_cpu_reset),      // Reset CPU from debug interface

    .dbg_freeze        (dbg_freeze),         // Freeze peripherals

    .dbg_halt_cmd      (dbg_halt_cmd),       // Halt CPU command

    .dbg_i2c_sda_out   (dbg_i2c_sda_out),    // Debug interface: I2C SDA OUT

    .dbg_mem_addr      (dbg_mem_addr),       // Debug address for rd/wr access

    .dbg_mem_dout      (dbg_mem_dout),       // Debug unit data output

    .dbg_mem_en        (dbg_mem_en),         // Debug unit memory enable

    .dbg_mem_wr        (dbg_mem_wr),         // Debug unit memory write

    .dbg_reg_wr        (dbg_reg_wr),         // Debug unit CPU register write

    .dbg_uart_txd      (dbg_uart_txd),       // Debug interface: UART TXD

// INPUTs

    .cpu_en_s          (cpu_en_s),           // Enable CPU code execution (synchronous)

    .cpu_id            (cpu_id),             // CPU ID

    .cpu_nr_inst       (cpu_nr_inst),        // Current oMSP instance number

    .cpu_nr_total      (cpu_nr_total),       // Total number of oMSP instances-1

    .dbg_clk           (dbg_clk),            // Debug unit clock

    .dbg_en_s          (dbg_en_s),           // Debug interface enable (synchronous)

    .dbg_halt_st       (cpu_halt_st),        // Halt/Run status from CPU

    .dbg_i2c_addr      (dbg_i2c_addr),       // Debug interface: I2C Address

    .dbg_i2c_broadcast (dbg_i2c_broadcast),  // Debug interface: I2C Broadcast Address (for multicore systems)

    .dbg_i2c_scl       (dbg_i2c_scl),        // Debug interface: I2C SCL

    .dbg_i2c_sda_in    (dbg_i2c_sda_in),     // Debug interface: I2C SDA IN

    .dbg_mem_din       (dbg_mem_din),        // Debug unit Memory data input

    .dbg_reg_din       (dbg_reg_din),        // Debug unit CPU register data input

    .dbg_rst           (dbg_rst),            // Debug unit reset

    .dbg_uart_rxd      (dbg_uart_rxd),       // Debug interface: UART RXD (asynchronous)

    .decode_noirq      (decode_noirq),       // Frontend decode instruction

    .eu_mab            (eu_mab),             // Execution-Unit Memory address bus

    .eu_mb_en          (eu_mb_en),           // Execution-Unit Memory bus enable

    .eu_mb_wr          (eu_mb_wr),           // Execution-Unit Memory bus write transfer

    .fe_mdb_in         (fe_mdb_in),          // Frontend Memory data bus input

    .pc                (pc),                 // Program counter

    .puc_pnd_set       (puc_pnd_set)         // PUC pending set for the serial debug interface

);

`else

assign      dbg_cpu_reset            =  1'b0;

assign      dbg_freeze               =  ~cpu_en_s;

assign      dbg_halt_cmd             =  1'b0;

assign      dbg_i2c_sda_out          =  1'b1;

assign      dbg_mem_addr             = 16'h0000;

assign      dbg_mem_dout             = 16'h0000;

assign      dbg_mem_en               =  1'b0;

assign      dbg_mem_wr               =  2'b00;

assign      dbg_reg_wr               =  1'b0;