Subversion Repositories openmsp430

//----------------------------------------------------------------------------

// Copyright (C) 2009 , Olivier Girard

//

// Redistribution and use in source and binary forms, with or without

// modification, are permitted provided that the following conditions

// are met:

//     * Redistributions of source code must retain the above copyright

//       notice, this list of conditions and the following disclaimer.

//     * Redistributions in binary form must reproduce the above copyright

//       notice, this list of conditions and the following disclaimer in the

//       documentation and/or other materials provided with the distribution.

//     * Neither the name of the authors nor the names of its contributors

//       may be used to endorse or promote products derived from this software

//       without specific prior written permission.

//

// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE

// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF

// THE POSSIBILITY OF SUCH DAMAGE

//

//----------------------------------------------------------------------------

//

// *File Name: omsp_clock_module.v

// 

// *Module Description:

//                       Basic clock module implementation.

//

// *Author(s):

//              - Olivier Girard,    olgirard@gmail.com

//

//----------------------------------------------------------------------------

// $Rev: 103 $

// $LastChangedBy: olivier.girard $

// $LastChangedDate: 2011-03-05 15:44:48 +0100 (Sat, 05 Mar 2011) $

//----------------------------------------------------------------------------

`ifdef OMSP_NO_INCLUDE

`else

`include "openMSP430_defines.v"

`endif

module  omsp_clock_module (

// OUTPUTs

    aclk,                         // ACLK

    aclk_en,                      // ACLK enable

    cpu_en_s,                     // Enable CPU code execution (synchronous)

    dbg_clk,                      // Debug unit clock

    dbg_en_s,                     // Debug interface enable (synchronous)

    dbg_rst,                      // Debug unit reset

    dco_enable,                   // Fast oscillator enable

    dco_wkup,                     // Fast oscillator wake-up (asynchronous)

    lfxt_enable,                  // Low frequency oscillator enable

    lfxt_wkup,                    // Low frequency oscillator wake-up (asynchronous)

    mclk,                         // Main system clock

    per_dout,                     // Peripheral data output

    por,                          // Power-on reset

    puc_pnd_set,                  // PUC pending set for the serial debug interface

    puc_rst,                      // Main system reset

    smclk,                        // SMCLK

    smclk_en,                     // SMCLK enable

// INPUTs

    cpu_en,                       // Enable CPU code execution (asynchronous)

    cpuoff,                       // Turns off the CPU

    dbg_cpu_reset,                // Reset CPU from debug interface

    dbg_en,                       // Debug interface enable (asynchronous)

    dco_clk,                      // Fast oscillator (fast clock)

    lfxt_clk,                     // Low frequency oscillator (typ 32kHz)

    mclk_enable,                  // Main System Clock enable

    mclk_wkup,                    // Main System Clock wake-up (asynchronous)

    oscoff,                       // Turns off LFXT1 clock input

    per_addr,                     // Peripheral address

    per_din,                      // Peripheral data input

    per_en,                       // Peripheral enable (high active)

    per_we,                       // Peripheral write enable (high active)

    reset_n,                      // Reset Pin (low active, asynchronous)

    scan_enable,                  // Scan enable (active during scan shifting)

    scan_mode,                    // Scan mode

    scg0,                         // System clock generator 1. Turns off the DCO

    scg1,                         // System clock generator 1. Turns off the SMCLK

    wdt_reset                     // Watchdog-timer reset

);

// OUTPUTs

//=========

output              aclk;         // ACLK

output              aclk_en;      // ACLK enable

output              cpu_en_s;     // Enable CPU code execution (synchronous)

output              dbg_clk;      // Debug unit clock

output              dbg_en_s;     // Debug unit enable (synchronous)

output              dbg_rst;      // Debug unit reset

output              dco_enable;   // Fast oscillator enable

output              dco_wkup;     // Fast oscillator wake-up (asynchronous)

output              lfxt_enable;  // Low frequency oscillator enable

output              lfxt_wkup;    // Low frequency oscillator wake-up (asynchronous)

output              mclk;         // Main system clock

output       [15:0] per_dout;     // Peripheral data output

output              por;          // Power-on reset

output              puc_pnd_set;  // PUC pending set for the serial debug interface

output              puc_rst;      // Main system reset

output              smclk;        // SMCLK

output              smclk_en;     // SMCLK enable

// INPUTs

//=========

input               cpu_en;       // Enable CPU code execution (asynchronous)

input               cpuoff;       // Turns off the CPU

input               dbg_cpu_reset;// Reset CPU from debug interface

input               dbg_en;       // Debug interface enable (asynchronous)

input               dco_clk;      // Fast oscillator (fast clock)

input               lfxt_clk;     // Low frequency oscillator (typ 32kHz)

input               mclk_enable;  // Main System Clock enable

input               mclk_wkup;    // Main System Clock wake-up (asynchronous)

input               oscoff;       // Turns off LFXT1 clock input

input        [13:0] per_addr;     // Peripheral address

input        [15:0] per_din;      // Peripheral data input

input               per_en;       // Peripheral enable (high active)

input         [1:0] per_we;       // Peripheral write enable (high active)

input               reset_n;      // Reset Pin (low active, asynchronous)

input               scan_enable;  // Scan enable (active during scan shifting)

input               scan_mode;    // Scan mode

input               scg0;         // System clock generator 1. Turns off the DCO

input               scg1;         // System clock generator 1. Turns off the SMCLK

input               wdt_reset;    // Watchdog-timer reset

//=============================================================================

// 1)  WIRES & PARAMETER DECLARATION

//=============================================================================

// Register base address (must be aligned to decoder bit width)

parameter       [14:0] BASE_ADDR   = 15'h0050;

// Decoder bit width (defines how many bits are considered for address decoding)

parameter              DEC_WD      =  4;

// Register addresses offset

parameter [DEC_WD-1:0] BCSCTL1     =  'h7,

                       BCSCTL2     =  'h8;

// Register one-hot decoder utilities

parameter              DEC_SZ      =  (1 << DEC_WD);

parameter [DEC_SZ-1:0] BASE_REG    =  {{DEC_SZ-1{1'b0}}, 1'b1};

// Register one-hot decoder

parameter [DEC_SZ-1:0] BCSCTL1_D   = (BASE_REG << BCSCTL1),

                       BCSCTL2_D   = (BASE_REG << BCSCTL2);

// Local wire declarations

wire nodiv_mclk;

wire nodiv_mclk_n;

wire nodiv_smclk;

//============================================================================

// 2)  REGISTER DECODER

//============================================================================

// Local register selection

wire              reg_sel      =  per_en & (per_addr[13:DEC_WD-1]==BASE_ADDR[14:DEC_WD]);

// Register local address

wire [DEC_WD-1:0] reg_addr     =  {1'b0, per_addr[DEC_WD-2:0]};

// Register address decode

wire [DEC_SZ-1:0] reg_dec      = (BCSCTL1_D  &  {DEC_SZ{(reg_addr==(BCSCTL1 >>1))}}) |

                                 (BCSCTL2_D  &  {DEC_SZ{(reg_addr==(BCSCTL2 >>1))}});

// Read/Write probes

wire              reg_lo_write =  per_we[0] & reg_sel;

wire              reg_hi_write =  per_we[1] & reg_sel;

wire              reg_read     = ~|per_we   & reg_sel;

// Read/Write vectors

wire [DEC_SZ-1:0] reg_hi_wr    = reg_dec & {DEC_SZ{reg_hi_write}};

wire [DEC_SZ-1:0] reg_lo_wr    = reg_dec & {DEC_SZ{reg_lo_write}};

wire [DEC_SZ-1:0] reg_rd       = reg_dec & {DEC_SZ{reg_read}};

//============================================================================

// 3) REGISTERS

//============================================================================

// BCSCTL1 Register

//--------------

reg  [7:0] bcsctl1;

wire       bcsctl1_wr  = BCSCTL1[0] ? reg_hi_wr[BCSCTL1] : reg_lo_wr[BCSCTL1];

wire [7:0] bcsctl1_nxt = BCSCTL1[0] ? per_din[15:8]      : per_din[7:0];

`ifdef ASIC_CLOCKING

  `ifdef ACLK_DIVIDER

wire [7:0] divax_mask = 8'h30;

  `else

wire [7:0] divax_mask = 8'h00;

  `endif

`else

wire [7:0] divax_mask = 8'h30;

`endif

always @ (posedge mclk or posedge puc_rst)

  if (puc_rst)          bcsctl1  <=  8'h00;

  else if (bcsctl1_wr)  bcsctl1  <=  bcsctl1_nxt & divax_mask; // Mask unused bits

// BCSCTL2 Register

//--------------

reg  [7:0] bcsctl2;

wire       bcsctl2_wr    = BCSCTL2[0] ? reg_hi_wr[BCSCTL2] : reg_lo_wr[BCSCTL2];

wire [7:0] bcsctl2_nxt   = BCSCTL2[0] ? per_din[15:8]      : per_din[7:0];

`ifdef MCLK_MUX

wire [7:0] selmx_mask = 8'h80;

`else

wire [7:0] selmx_mask = 8'h00;

`endif

`ifdef MCLK_DIVIDER

wire [7:0] divmx_mask = 8'h30;

`else

wire [7:0] divmx_mask = 8'h00;

`endif

`ifdef ASIC_CLOCKING

  `ifdef SMCLK_MUX

wire [7:0] sels_mask  = 8'h08;

  `else

wire [7:0] sels_mask  = 8'h00;

  `endif

  `ifdef SMCLK_DIVIDER

wire [7:0] divsx_mask = 8'h06;

  `else

wire [7:0] divsx_mask = 8'h00;

  `endif

`else

wire [7:0] sels_mask  = 8'h08;

wire [7:0] divsx_mask = 8'h06;

`endif

always @ (posedge mclk or posedge puc_rst)

  if (puc_rst)          bcsctl2  <=  8'h00;

  else if (bcsctl2_wr)  bcsctl2  <=  bcsctl2_nxt & ( sels_mask  | divsx_mask |

                                                     selmx_mask | divmx_mask); // Mask unused bits

//============================================================================

// 4) DATA OUTPUT GENERATION

//============================================================================

// Data output mux

wire [15:0] bcsctl1_rd   = {8'h00, (bcsctl1  & {8{reg_rd[BCSCTL1]}})}  << (8 & {4{BCSCTL1[0]}});

wire [15:0] bcsctl2_rd   = {8'h00, (bcsctl2  & {8{reg_rd[BCSCTL2]}})}  << (8 & {4{BCSCTL2[0]}});

wire [15:0] per_dout =  bcsctl1_rd   |

                        bcsctl2_rd;

//=============================================================================

// 5)  DCO_CLK / LFXT_CLK INTERFACES (WAKEUP, ENABLE, ...)

//=============================================================================

`ifdef ASIC_CLOCKING

   wire cpuoff_and_mclk_enable;

   omsp_and_gate and_cpuoff_mclk_en (.y(cpuoff_and_mclk_enable), .a(cpuoff), .b(mclk_enable));

`endif

//-----------------------------------------------------------

// 5.1) HIGH SPEED SYSTEM CLOCK GENERATOR (DCO_CLK)

//-----------------------------------------------------------

// Note1: switching off the DCO osillator is only

//        supported in ASIC mode with SCG0 low power mode

//

// Note2: unlike the original MSP430 specification,

//        we allow to switch off the DCO even

//        if it is selected by MCLK or SMCLK.

wire por_a;

wire dco_wkup;

wire cpu_en_wkup;

`ifdef SCG0_EN

   // The DCO oscillator is synchronously disabled if:

   //      - the cpu pin is disabled (in that case, wait for mclk_enable==0)

   //      - the debug interface is disabled

   //      - SCG0 is set (in that case, wait for the mclk_enable==0 if selected by SELMx)

   //

   // Note that we make extensive use of the AND gate module in order

   // to prevent glitch propagation on the wakeup logic cone.

   wire cpu_enabled_with_dco;

   wire dco_not_enabled_by_dbg;

   wire dco_disable_by_scg0;

   wire dco_disable_by_cpu_en;

   wire dco_enable_nxt;

   omsp_and_gate and_dco_dis1 (.y(cpu_enabled_with_dco),   .a(~bcsctl2[`SELMx]),     .b(cpuoff_and_mclk_enable));

   omsp_and_gate and_dco_dis2 (.y(dco_not_enabled_by_dbg), .a(~dbg_en_s),            .b(~cpu_enabled_with_dco));

   omsp_and_gate and_dco_dis3 (.y(dco_disable_by_scg0),    .a(scg0),                 .b(dco_not_enabled_by_dbg));

   omsp_and_gate and_dco_dis4 (.y(dco_disable_by_cpu_en),  .a(~cpu_en_s),            .b(~mclk_enable));

   omsp_and_gate and_dco_dis5 (.y(dco_enable_nxt),         .a(~dco_disable_by_scg0), .b(~dco_disable_by_cpu_en));

   // Register to prevent glitch propagation

   reg  dco_disable;

   always @(posedge nodiv_mclk_n or posedge por)

   if (por) dco_disable <= 1'b1;

   else     dco_disable <= ~dco_enable_nxt;

   // Note that a synchronizer is required if the MCLK mux is included

   wire dco_clk_n  = ~dco_clk;

   `ifdef MCLK_MUX

      omsp_sync_cell sync_cell_dco_disable (

         .data_out  (dco_enable),

         .data_in   (~dco_disable),

         .clk       (dco_clk_n),

         .rst       (por)

      );

   `else

      assign dco_enable     = ~dco_disable;

   `endif

   // The DCO oscillator will get an asynchronous wakeup if:

   //      - the MCLK  generates a wakeup (only if the MCLK mux selects dco_clk)

   //      - if the DCO wants to be synchronously enabled (i.e dco_enable_nxt=1)

   wire dco_mclk_wkup;

   wire dco_en_wkup;

   omsp_and_gate and_dco_mclk_wkup (.y(dco_mclk_wkup), .a(mclk_wkup),   .b(~bcsctl2[`SELMx]));

   omsp_and_gate and_dco_en_wkup   (.y(dco_en_wkup),   .a(~dco_enable), .b(dco_enable_nxt));

   wire dco_wkup_set = dco_mclk_wkup | dco_en_wkup | cpu_en_wkup;

   // Scan MUX for the asynchronous SET

   wire dco_wkup_set_scan;

   omsp_scan_mux scan_mux_dco_wkup (

                                    .scan_mode    (scan_mode),

                                    .data_in_scan (por_a),

                                    .data_in_func (dco_wkup_set | por),

                                    .data_out     (dco_wkup_set_scan)

                                   );

   // Scan MUX to increase coverage 

   wire dco_wkup_clear;

   omsp_scan_mux scan_mux_dco_wkup_clear (

                                          .scan_mode    (scan_mode),

                                          .data_in_scan (dco_wkup_set),

                                          .data_in_func (1'b1),

                                          .data_out     (dco_wkup_clear)

                                         );

   // The wakeup is asynchronously set, synchronously released

   wire dco_wkup_n;

   omsp_sync_cell sync_cell_dco_wkup (

       .data_out  (dco_wkup_n),

       .data_in   (dco_wkup_clear),

       .clk       (dco_clk_n),

       .rst       (dco_wkup_set_scan)

   );

   omsp_and_gate and_dco_wkup (.y(dco_wkup), .a(~dco_wkup_n), .b(cpu_en));

`else

   assign dco_enable    = 1'b1;

   assign dco_wkup      = 1'b1;

`endif

//-----------------------------------------------------------

// 5.2) LOW FREQUENCY CRYSTAL CLOCK GENERATOR (LFXT_CLK)

//-----------------------------------------------------------

// ASIC MODE

//------------------------------------------------

// Note: unlike the original MSP430 specification,

//       we allow to switch off the LFXT even

//       if it is selected by MCLK or SMCLK.

`ifdef ASIC_CLOCKING

`ifdef OSCOFF_EN

   // The LFXT is synchronously disabled if:

   //      - the cpu pin is disabled (in that case, wait for mclk_enable==0)

   //      - the debug interface is disabled

   //      - OSCOFF is set (in that case, wait for the mclk_enable==0 if selected by SELMx)

   wire cpu_enabled_with_lfxt;

   wire lfxt_not_enabled_by_dbg;

   wire lfxt_disable_by_oscoff;

   wire lfxt_disable_by_cpu_en;

   wire lfxt_enable_nxt;

   omsp_and_gate and_lfxt_dis1 (.y(cpu_enabled_with_lfxt),   .a(bcsctl2[`SELMx]),         .b(cpuoff_and_mclk_enable));

   omsp_and_gate and_lfxt_dis2 (.y(lfxt_not_enabled_by_dbg), .a(~dbg_en_s),               .b(~cpu_enabled_with_lfxt));

   omsp_and_gate and_lfxt_dis3 (.y(lfxt_disable_by_oscoff),  .a(oscoff),                  .b(lfxt_not_enabled_by_dbg));

   omsp_and_gate and_lfxt_dis4 (.y(lfxt_disable_by_cpu_en),  .a(~cpu_en_s),               .b(~mclk_enable));

   omsp_and_gate and_lfxt_dis5 (.y(lfxt_enable_nxt),         .a(~lfxt_disable_by_oscoff), .b(~lfxt_disable_by_cpu_en));

   // Register to prevent glitch propagation

   reg  lfxt_disable;

   always @(posedge nodiv_mclk_n or posedge por)

   if (por) lfxt_disable <= 1'b1;

   else     lfxt_disable <= ~lfxt_enable_nxt;

   // Synchronize the OSCOFF control signal to the LFXT clock domain

   wire lfxt_clk_n  = ~lfxt_clk;

   omsp_sync_cell sync_cell_lfxt_disable (

      .data_out  (lfxt_enable),

      .data_in   (~lfxt_disable),

      .clk       (lfxt_clk_n),

      .rst       (por)

   );

   // The LFXT will get an asynchronous wakeup if:

   //      - the MCLK  generates a wakeup (only if the MCLK  mux selects lfxt_clk)

   //      - if the LFXT wants to be synchronously enabled (i.e lfxt_enable_nxt=1)

   wire lfxt_mclk_wkup;

   wire lfxt_en_wkup;

   omsp_and_gate and_lfxt_mclk_wkup (.y(lfxt_mclk_wkup), .a(mclk_wkup),    .b(bcsctl2[`SELMx]));

   omsp_and_gate and_lfxt_en_wkup   (.y(lfxt_en_wkup),   .a(~lfxt_enable), .b(lfxt_enable_nxt));

   wire   lfxt_wkup_set  = lfxt_mclk_wkup | lfxt_en_wkup | cpu_en_wkup;

   // Scan MUX for the asynchronous SET

   wire lfxt_wkup_set_scan;

   omsp_scan_mux scan_mux_lfxt_wkup (

                                     .scan_mode    (scan_mode),

                                     .data_in_scan (por_a),

                                     .data_in_func (lfxt_wkup_set | por),

                                     .data_out     (lfxt_wkup_set_scan)

                                    );

   // Scan MUX to increase coverage 

   wire lfxt_wkup_clear;

   omsp_scan_mux scan_mux_lfxt_wkup_clear (

                                           .scan_mode    (scan_mode),

                                           .data_in_scan (lfxt_wkup_set),

                                           .data_in_func (1'b1),

                                           .data_out     (lfxt_wkup_clear)

                                          );

   // The wakeup is asynchronously set, synchronously released

   wire lfxt_wkup_n;

   omsp_sync_cell sync_cell_lfxt_wkup (

       .data_out  (lfxt_wkup_n),

       .data_in   (lfxt_wkup_clear),

       .clk       (lfxt_clk_n),

       .rst       (lfxt_wkup_set_scan)

   );

   omsp_and_gate and_lfxt_wkup (.y(lfxt_wkup), .a(~lfxt_wkup_n), .b(cpu_en));

`else

   assign lfxt_enable    = 1'b1;

   assign lfxt_wkup      = 1'b0;

`endif

// FPGA MODE

//---------------------------------------

// Synchronize LFXT_CLK & edge detection

`else

wire lfxt_clk_s;

omsp_sync_cell sync_cell_lfxt_clk (

    .data_out  (lfxt_clk_s),

    .data_in   (lfxt_clk),

    .clk       (mclk),

    .rst       (por)

);

reg  lfxt_clk_dly;

always @ (posedge mclk or posedge por)

  if (por) lfxt_clk_dly <=  1'b0;

  else     lfxt_clk_dly <=  lfxt_clk_s;

wire   lfxt_clk_en = (lfxt_clk_s & ~lfxt_clk_dly) & ~(oscoff & ~bcsctl2[`SELS]);

assign lfxt_enable = 1'b1;

assign lfxt_wkup   = 1'b0;

`endif

//=============================================================================

// 6)  CLOCK GENERATION

//=============================================================================

//-----------------------------------------------------------

// 6.1) GLOBAL CPU ENABLE

//-----------------------------------------------------------

// ACLK and SMCLK are directly switched-off

// with the cpu_en pin (after synchronization).

// MCLK will be switched off once the CPU reaches

// its IDLE state (through the mclk_enable signal)

// Synchronize CPU_EN signal to the MCLK domain

//----------------------------------------------

`ifdef SYNC_CPU_EN

   omsp_sync_cell sync_cell_cpu_en (

      .data_out  (cpu_en_s),

      .data_in   (cpu_en),

      .clk       (nodiv_mclk),

      .rst       (por)

   );

   omsp_and_gate and_cpu_en_wkup (.y(cpu_en_wkup), .a(cpu_en), .b(~cpu_en_s));

`else

   assign cpu_en_s    = cpu_en;

   assign cpu_en_wkup = 1'b0;

`endif

// Synchronize CPU_EN signal to the ACLK domain

//----------------------------------------------

`ifdef LFXT_DOMAIN

   wire cpu_en_aux_s;

   omsp_sync_cell sync_cell_cpu_aux_en (

      .data_out  (cpu_en_aux_s),

      .data_in   (cpu_en),

      .clk       (lfxt_clk),

      .rst       (por)

   );

`else

   wire   cpu_en_aux_s    = cpu_en_s;

`endif

// Synchronize CPU_EN signal to the SMCLK domain

//----------------------------------------------

// Note: the synchronizer is only required if there is a SMCLK_MUX

`ifdef ASIC_CLOCKING

  `ifdef SMCLK_MUX

     wire cpu_en_sm_s;

     omsp_sync_cell sync_cell_cpu_sm_en (

        .data_out  (cpu_en_sm_s),

        .data_in   (cpu_en),

        .clk       (nodiv_smclk),

        .rst       (por)

     );

  `else

   wire   cpu_en_sm_s    = cpu_en_s;

  `endif

`endif

//-----------------------------------------------------------

// 6.2) MCLK GENERATION

//-----------------------------------------------------------

// Clock MUX

//----------------------------

`ifdef MCLK_MUX

omsp_clock_mux clock_mux_mclk (

   .clk_out   (nodiv_mclk),

   .clk_in0   (dco_clk),

   .clk_in1   (lfxt_clk),

   .reset     (por),

   .scan_mode (scan_mode),

   .select    (bcsctl2[`SELMx])

);

`else

assign nodiv_mclk   =  dco_clk;

`endif

assign nodiv_mclk_n = ~nodiv_mclk;

// Wakeup synchronizer

//----------------------------

wire mclk_wkup_s;

`ifdef CPUOFF_EN

omsp_sync_cell sync_cell_mclk_wkup (

   .data_out  (mclk_wkup_s),

   .data_in   (mclk_wkup),

   .clk       (nodiv_mclk),

   .rst       (puc_rst)

);

`else

   assign mclk_wkup_s = 1'b0;

`endif

// Clock Divider

//----------------------------

// No need for extra synchronizer as bcsctl2

// comes from the same clock domain.

`ifdef CPUOFF_EN

wire mclk_active = mclk_enable | mclk_wkup_s | (dbg_en_s & cpu_en_s);

`else

wire mclk_active = 1'b1;

`endif

`ifdef MCLK_DIVIDER

reg [2:0] mclk_div;

always @ (posedge nodiv_mclk or posedge puc_rst)

  if (puc_rst)                       mclk_div <=  3'h0;

  else if ((bcsctl2[`DIVMx]!=2'b00)) mclk_div <=  mclk_div+3'h1;

  wire  mclk_div_en = mclk_active & ((bcsctl2[`DIVMx]==2'b00) ?  1'b1          :

                                     (bcsctl2[`DIVMx]==2'b01) ?  mclk_div[0]   :

                                     (bcsctl2[`DIVMx]==2'b10) ? &mclk_div[1:0] :

                                                                &mclk_div[2:0]);

`else

  wire  mclk_div_en = mclk_active;

`endif

// Generate main system clock

//----------------------------

`ifdef MCLK_CGATE

omsp_clock_gate clock_gate_mclk (

    .gclk        (mclk),

    .clk         (nodiv_mclk),

    .enable      (mclk_div_en),

    .scan_enable (scan_enable)

);

`else

   assign mclk   = nodiv_mclk;

`endif

//-----------------------------------------------------------

// 6.3) ACLK GENERATION

//-----------------------------------------------------------

// ASIC MODE

//----------------------------

`ifdef ASIC_CLOCKING

  `ifdef ACLK_DIVIDER

    `ifdef LFXT_DOMAIN

   wire nodiv_aclk = lfxt_clk;

   // Local Reset synchronizer

   wire puc_lfxt_rst;

   wire puc_lfxt_noscan_n;

   omsp_sync_cell sync_cell_puc_lfxt (

       .data_out     (puc_lfxt_noscan_n),

       .data_in      (1'b1),

       .clk          (nodiv_aclk),

       .rst          (puc_rst)

   );

   omsp_scan_mux scan_mux_puc_lfxt (

       .scan_mode    (scan_mode),

       .data_in_scan (por_a),

       .data_in_func (~puc_lfxt_noscan_n),

       .data_out     (puc_lfxt_rst)

   );

   // Local synchronizer for the bcsctl1.DIVAx configuration

   // (note that we can live with a full bus synchronizer as

   //  it won't hurt if we get a wrong DIVAx value for a single clock cycle)

   reg [1:0] divax_s;

   reg [1:0] divax_ss;

   always @ (posedge nodiv_aclk or posedge puc_lfxt_rst)

     if (puc_lfxt_rst)

       begin

          divax_s  <=  2'h0;

          divax_ss <=  2'h0;

       end

     else

       begin

          divax_s  <=  bcsctl1[`DIVAx];

          divax_ss <=  divax_s;

       end

     // If the OSCOFF mode is enabled synchronize OSCOFF signal

     wire oscoff_s;

     `ifdef OSCOFF_EN

         omsp_sync_cell sync_cell_oscoff (

           .data_out     (oscoff_s),