Subversion Repositories openmsp430

//----------------------------------------------------------------------------

// Copyright (C) 2009 , Olivier Girard

//

// Redistribution and use in source and binary forms, with or without

// modification, are permitted provided that the following conditions

// are met:

//     * Redistributions of source code must retain the above copyright

//       notice, this list of conditions and the following disclaimer.

//     * Redistributions in binary form must reproduce the above copyright

//       notice, this list of conditions and the following disclaimer in the

//       documentation and/or other materials provided with the distribution.

//     * Neither the name of the authors nor the names of its contributors

//       may be used to endorse or promote products derived from this software

//       without specific prior written permission.

//

// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"

// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE

// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,

// OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF

// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS

// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN

// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)

// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF

// THE POSSIBILITY OF SUCH DAMAGE

//

//----------------------------------------------------------------------------

//

// *File Name: omsp_frontend.v

//

// *Module Description:

//                       openMSP430 Instruction fetch and decode unit

//

// *Author(s):

//              - Olivier Girard,    olgirard@gmail.com

//

//----------------------------------------------------------------------------

// $Rev: 103 $

// $LastChangedBy: olivier.girard $

// $LastChangedDate: 2011-03-05 15:44:48 +0100 (Sat, 05 Mar 2011) $

//----------------------------------------------------------------------------

`ifdef OMSP_NO_INCLUDE

`else

`include "openMSP430_defines.v"

`endif

module  omsp_frontend (

// OUTPUTs

    cpu_halt_st,                       // Halt/Run status from CPU

    decode_noirq,                      // Frontend decode instruction

    e_state,                           // Execution state

    exec_done,                         // Execution completed

    inst_ad,                           // Decoded Inst: destination addressing mode

    inst_as,                           // Decoded Inst: source addressing mode

    inst_alu,                          // ALU control signals

    inst_bw,                           // Decoded Inst: byte width

    inst_dest,                         // Decoded Inst: destination (one hot)

    inst_dext,                         // Decoded Inst: destination extended instruction word

    inst_irq_rst,                      // Decoded Inst: Reset interrupt

    inst_jmp,                          // Decoded Inst: Conditional jump

    inst_mov,                          // Decoded Inst: mov instruction

    inst_sext,                         // Decoded Inst: source extended instruction word

    inst_so,                           // Decoded Inst: Single-operand arithmetic

    inst_src,                          // Decoded Inst: source (one hot)

    inst_type,                         // Decoded Instruction type

    irq_acc,                           // Interrupt request accepted (one-hot signal)

    mab,                               // Frontend Memory address bus

    mb_en,                             // Frontend Memory bus enable

    mclk_dma_enable,                   // DMA Sub-System Clock enable

    mclk_dma_wkup,                     // DMA Sub-System Clock wake-up (asynchronous)

    mclk_enable,                       // Main System Clock enable

    mclk_wkup,                         // Main System Clock wake-up (asynchronous)

    nmi_acc,                           // Non-Maskable interrupt request accepted

    pc,                                // Program counter

    pc_nxt,                            // Next PC value (for CALL & IRQ)

// INPUTs

    cpu_en_s,                          // Enable CPU code execution (synchronous)

    cpu_halt_cmd,                      // Halt CPU command

    cpuoff,                            // Turns off the CPU

    dbg_reg_sel,                       // Debug selected register for rd/wr access

    dma_en,                            // Direct Memory Access enable (high active)

    dma_wkup,                          // DMA Sub-System Wake-up (asynchronous and non-glitchy)

    fe_pmem_wait,                      // Frontend wait for Instruction fetch

    gie,                               // General interrupt enable

    irq,                               // Maskable interrupts

    mclk,                              // Main system clock

    mdb_in,                            // Frontend Memory data bus input

    nmi_pnd,                           // Non-maskable interrupt pending

    nmi_wkup,                          // NMI Wakeup

    pc_sw,                             // Program counter software value

    pc_sw_wr,                          // Program counter software write

    puc_rst,                           // Main system reset

    scan_enable,                       // Scan enable (active during scan shifting)

    wdt_irq,                           // Watchdog-timer interrupt

    wdt_wkup,                          // Watchdog Wakeup

    wkup                               // System Wake-up (asynchronous)

);

// OUTPUTs

//=========

output               cpu_halt_st;      // Halt/Run status from CPU

output               decode_noirq;     // Frontend decode instruction

output         [3:0] e_state;          // Execution state

output               exec_done;        // Execution completed

output         [7:0] inst_ad;          // Decoded Inst: destination addressing mode

output         [7:0] inst_as;          // Decoded Inst: source addressing mode

output        [11:0] inst_alu;         // ALU control signals

output               inst_bw;          // Decoded Inst: byte width

output        [15:0] inst_dest;        // Decoded Inst: destination (one hot)

output        [15:0] inst_dext;        // Decoded Inst: destination extended instruction word

output               inst_irq_rst;     // Decoded Inst: Reset interrupt

output         [7:0] inst_jmp;         // Decoded Inst: Conditional jump

output               inst_mov;         // Decoded Inst: mov instruction

output        [15:0] inst_sext;        // Decoded Inst: source extended instruction word

output         [7:0] inst_so;          // Decoded Inst: Single-operand arithmetic

output        [15:0] inst_src;         // Decoded Inst: source (one hot)

output         [2:0] inst_type;        // Decoded Instruction type

output [`IRQ_NR-3:0] irq_acc;          // Interrupt request accepted (one-hot signal)

output        [15:0] mab;              // Frontend Memory address bus

output               mb_en;            // Frontend Memory bus enable

output               mclk_dma_enable;  // DMA Sub-System Clock enable

output               mclk_dma_wkup;    // DMA Sub-System Clock wake-up (asynchronous)

output               mclk_enable;      // Main System Clock enable

output               mclk_wkup;        // Main System Clock wake-up (asynchronous)

output               nmi_acc;          // Non-Maskable interrupt request accepted

output        [15:0] pc;               // Program counter

output        [15:0] pc_nxt;           // Next PC value (for CALL & IRQ)

// INPUTs

//=========

input                cpu_en_s;         // Enable CPU code execution (synchronous)

input                cpu_halt_cmd;     // Halt CPU command

input                cpuoff;           // Turns off the CPU

input          [3:0] dbg_reg_sel;      // Debug selected register for rd/wr access

input                dma_en;           // Direct Memory Access enable (high active)

input                dma_wkup;         // DMA Sub-System Wake-up (asynchronous and non-glitchy)

input                fe_pmem_wait;     // Frontend wait for Instruction fetch

input                gie;              // General interrupt enable

input  [`IRQ_NR-3:0] irq;              // Maskable interrupts

input                mclk;             // Main system clock

input         [15:0] mdb_in;           // Frontend Memory data bus input

input                nmi_pnd;          // Non-maskable interrupt pending

input                nmi_wkup;         // NMI Wakeup

input         [15:0] pc_sw;            // Program counter software value

input                pc_sw_wr;         // Program counter software write

input                puc_rst;          // Main system reset

input                scan_enable;      // Scan enable (active during scan shifting)

input                wdt_irq;          // Watchdog-timer interrupt

input                wdt_wkup;         // Watchdog Wakeup

input                wkup;             // System Wake-up (asynchronous)

//=============================================================================

// 1)  UTILITY FUNCTIONS

//=============================================================================

// 64 bits one-hot decoder

function [63:0] one_hot64;

   input  [5:0] binary;

   begin

      one_hot64         = 64'h0000_0000_0000_0000;

      one_hot64[binary] =  1'b1;

   end

endfunction

// 16 bits one-hot decoder

function [15:0] one_hot16;

   input  [3:0] binary;

   begin

      one_hot16         = 16'h0000;

      one_hot16[binary] =  1'b1;

   end

endfunction

// 8 bits one-hot decoder

function [7:0] one_hot8;

   input  [2:0] binary;

   begin

      one_hot8         = 8'h00;

      one_hot8[binary] = 1'b1;

   end

endfunction

// Get IRQ number

function  [5:0] get_irq_num;

   input [62:0] irq_all;

   integer      ii;

   begin

      get_irq_num = 6'h3f;

      for (ii = 62; ii >= 0; ii = ii - 1)

        if (&get_irq_num & irq_all[ii]) get_irq_num = ii[5:0];

   end

endfunction

//=============================================================================

// 2)  PARAMETER DEFINITIONS

//=============================================================================

//

// 2.1) Instruction State machine definitons

//-------------------------------------------

parameter I_IRQ_FETCH = `I_IRQ_FETCH;

parameter I_IRQ_DONE  = `I_IRQ_DONE;

parameter I_DEC       = `I_DEC;        // New instruction ready for decode

parameter I_EXT1      = `I_EXT1;       // 1st Extension word

parameter I_EXT2      = `I_EXT2;       // 2nd Extension word

parameter I_IDLE      = `I_IDLE;       // CPU is in IDLE mode

//

// 2.2) Execution State machine definitons

//-------------------------------------------

parameter E_IRQ_0     = `E_IRQ_0;

parameter E_IRQ_1     = `E_IRQ_1;

parameter E_IRQ_2     = `E_IRQ_2;

parameter E_IRQ_3     = `E_IRQ_3;

parameter E_IRQ_4     = `E_IRQ_4;

parameter E_SRC_AD    = `E_SRC_AD;

parameter E_SRC_RD    = `E_SRC_RD;

parameter E_SRC_WR    = `E_SRC_WR;

parameter E_DST_AD    = `E_DST_AD;

parameter E_DST_RD    = `E_DST_RD;

parameter E_DST_WR    = `E_DST_WR;

parameter E_EXEC      = `E_EXEC;

parameter E_JUMP      = `E_JUMP;

parameter E_IDLE      = `E_IDLE;

//=============================================================================

// 3)  FRONTEND STATE MACHINE

//=============================================================================

// The wire "conv" is used as state bits to calculate the next response

reg  [2:0] i_state;

reg  [2:0] i_state_nxt;

reg  [1:0] inst_sz;

wire [1:0] inst_sz_nxt;

wire       irq_detect;

wire [2:0] inst_type_nxt;

wire       is_const;

reg [15:0] sconst_nxt;

reg  [3:0] e_state_nxt;

// CPU on/off through an external interface (debug or mstr) or cpu_en port

wire   cpu_halt_req = cpu_halt_cmd | ~cpu_en_s;

// States Transitions

always @(i_state    or inst_sz  or inst_sz_nxt  or pc_sw_wr or exec_done or

         irq_detect or cpuoff   or cpu_halt_req or e_state)

    case(i_state)

      I_IDLE     : i_state_nxt = (irq_detect & ~cpu_halt_req) ? I_IRQ_FETCH :

                                 (~cpuoff    & ~cpu_halt_req) ? I_DEC       : I_IDLE;

      I_IRQ_FETCH: i_state_nxt =  I_IRQ_DONE;

      I_IRQ_DONE : i_state_nxt =  I_DEC;

      I_DEC      : i_state_nxt =  irq_detect                  ? I_IRQ_FETCH :

                          (cpuoff | cpu_halt_req) & exec_done ? I_IDLE      :

                            cpu_halt_req & (e_state==E_IDLE)  ? I_IDLE      :

                                  pc_sw_wr                    ? I_DEC       :

                             ~exec_done & ~(e_state==E_IDLE)  ? I_DEC       :        // Wait in decode state

                                  (inst_sz_nxt!=2'b00)        ? I_EXT1      : I_DEC; // until execution is completed

      I_EXT1     : i_state_nxt =  pc_sw_wr                    ? I_DEC       :

                                  (inst_sz!=2'b01)            ? I_EXT2      : I_DEC;

      I_EXT2     : i_state_nxt =  I_DEC;

    // pragma coverage off

      default    : i_state_nxt =  I_IRQ_FETCH;

    // pragma coverage on

    endcase

// State machine

always @(posedge mclk or posedge puc_rst)

  if (puc_rst) i_state  <= I_IRQ_FETCH;

  else         i_state  <= i_state_nxt;

// Utility signals

wire   decode_noirq =  ((i_state==I_DEC) &  (exec_done | (e_state==E_IDLE)));

wire   decode       =  decode_noirq | irq_detect;

wire   fetch        = ~((i_state==I_DEC) & ~(exec_done | (e_state==E_IDLE))) & ~(e_state_nxt==E_IDLE);

// Halt/Run CPU status

reg    cpu_halt_st;

always @(posedge mclk or posedge puc_rst)

  if (puc_rst)  cpu_halt_st <= 1'b0;

  else          cpu_halt_st <= cpu_halt_req & (i_state_nxt==I_IDLE);

//=============================================================================

// 4)  INTERRUPT HANDLING & SYSTEM WAKEUP

//=============================================================================

//

// 4.1) INTERRUPT HANDLING

//-----------------------------------------

// Detect reset interrupt

reg         inst_irq_rst;

always @(posedge mclk or posedge puc_rst)

  if (puc_rst)                  inst_irq_rst <= 1'b1;

  else if (exec_done)           inst_irq_rst <= 1'b0;

//  Detect other interrupts

assign  irq_detect = (nmi_pnd | ((|irq | wdt_irq) & gie)) & ~cpu_halt_req & ~cpu_halt_st & (exec_done | (i_state==I_IDLE));

`ifdef CLOCK_GATING

wire       mclk_irq_num;

omsp_clock_gate clock_gate_irq_num (.gclk(mclk_irq_num),

                                    .clk (mclk), .enable(irq_detect), .scan_enable(scan_enable));

`else

wire       UNUSED_scan_enable = scan_enable;

wire       mclk_irq_num       = mclk;

`endif

// Combine all IRQs

`ifdef  IRQ_16

wire [62:0] irq_all     = {nmi_pnd, irq, 48'h0000_0000_0000} |

`else

`ifdef  IRQ_32

wire [62:0] irq_all     = {nmi_pnd, irq, 32'h0000_0000}      |

`else

`ifdef  IRQ_64

wire [62:0] irq_all     = {nmi_pnd, irq}                     |

`endif

`endif

`endif

                          {1'b0,    3'h0, wdt_irq, {58{1'b0}}};

// Select highest priority IRQ

reg  [5:0] irq_num;

always @(posedge mclk_irq_num or posedge puc_rst)

  if (puc_rst)         irq_num <= 6'h3f;

`ifdef CLOCK_GATING

  else

`else

  else if (irq_detect)

`endif

                       irq_num <= get_irq_num(irq_all);

// Generate selected IRQ vector address

wire [15:0] irq_addr    = {9'h1ff, irq_num, 1'b0};

// Interrupt request accepted

wire        [63:0] irq_acc_all = one_hot64(irq_num) & {64{(i_state==I_IRQ_FETCH)}};

wire [`IRQ_NR-3:0] irq_acc     = irq_acc_all[61:64-`IRQ_NR];

wire               nmi_acc     = irq_acc_all[62];

//

// 4.2) SYSTEM WAKEUP

//-----------------------------------------

`ifdef CPUOFF_EN

// Generate the main system clock enable signal

                                                    // Keep the clock running if:

wire mclk_enable = inst_irq_rst ? cpu_en_s :        //      - the RESET interrupt is currently executing

                                                    //        and if the CPU is enabled

                                                    // otherwise if:

                  ~((cpuoff | ~cpu_en_s) &          //      - the CPUOFF flag, cpu_en command, instruction

                   (i_state==I_IDLE) &              //        and execution state machines are all two

                   (e_state==E_IDLE));              //        not idle.

// Wakeup condition from maskable interrupts

wire mirq_wkup;

omsp_and_gate and_mirq_wkup     (.y(mirq_wkup),     .a(wkup | wdt_wkup),      .b(gie));

// Combined asynchronous wakeup detection from nmi & irq (masked if the cpu is disabled)

omsp_and_gate and_mclk_wkup     (.y(mclk_wkup),     .a(nmi_wkup | mirq_wkup), .b(cpu_en_s));

// Wakeup condition from DMA interface

  `ifdef DMA_IF_EN

wire mclk_dma_enable = dma_en & cpu_en_s;

omsp_and_gate and_mclk_dma_wkup (.y(mclk_dma_wkup), .a(dma_wkup),             .b(cpu_en_s));

  `else

assign  mclk_dma_wkup   = 1'b0;

assign  mclk_dma_enable = 1'b0;

wire    UNUSED_dma_en   = dma_en;

wire    UNUSED_dma_wkup = dma_wkup;

  `endif

`else

// In the CPUOFF feature is disabled, the wake-up and enable signals are always 1

assign  mclk_dma_wkup   = 1'b1;

assign  mclk_dma_enable = 1'b1;

assign  mclk_wkup       = 1'b1;

assign  mclk_enable     = 1'b1;

wire    UNUSED_dma_en   = dma_en;

wire    UNUSED_wkup     = wkup;

wire    UNUSED_wdt_wkup = wdt_wkup;

wire    UNUSED_nmi_wkup = nmi_wkup;

wire    UNUSED_dma_wkup = dma_wkup;

`endif

//=============================================================================

// 5)  FETCH INSTRUCTION

//=============================================================================

//

// 5.1) PROGRAM COUNTER & MEMORY INTERFACE

//-----------------------------------------

// Program counter

reg  [15:0] pc;

// Compute next PC value

wire [15:0] pc_incr = pc + {14'h0000, fetch, 1'b0};

wire [15:0] pc_nxt  = pc_sw_wr               ? pc_sw    :

                      (i_state==I_IRQ_FETCH) ? irq_addr :

                      (i_state==I_IRQ_DONE)  ? mdb_in   :  pc_incr;

`ifdef CLOCK_GATING

wire       pc_en  = fetch                  |

                    pc_sw_wr               |

                    (i_state==I_IRQ_FETCH) |

                    (i_state==I_IRQ_DONE);

wire       mclk_pc;

omsp_clock_gate clock_gate_pc (.gclk(mclk_pc),

                               .clk (mclk), .enable(pc_en), .scan_enable(scan_enable));

`else

wire       mclk_pc = mclk;

`endif

always @(posedge mclk_pc or posedge puc_rst)

  if (puc_rst)  pc <= 16'h0000;

  else          pc <= pc_nxt;

// Check if Program-Memory has been busy in order to retry Program-Memory access

reg pmem_busy;

always @(posedge mclk or posedge puc_rst)

  if (puc_rst)  pmem_busy <= 1'b0;

  else          pmem_busy <= fe_pmem_wait;

// Memory interface

wire [15:0] mab      = pc_nxt;

wire        mb_en    = fetch | pc_sw_wr | (i_state==I_IRQ_FETCH) | pmem_busy | (cpu_halt_st & ~cpu_halt_req);

//

// 5.2) INSTRUCTION REGISTER

//--------------------------------

// Instruction register

wire [15:0] ir  = mdb_in;

// Detect if source extension word is required

wire is_sext = (inst_as[`IDX] | inst_as[`SYMB] | inst_as[`ABS] | inst_as[`IMM]);

// For the Symbolic addressing mode, add -2 to the extension word in order

// to make up for the PC address

wire [15:0] ext_incr = ((i_state==I_EXT1)     &  inst_as[`SYMB]) |

                       ((i_state==I_EXT2)     &  inst_ad[`SYMB]) |

                       ((i_state==I_EXT1)     & ~inst_as[`SYMB] &

                       ~(i_state_nxt==I_EXT2) &  inst_ad[`SYMB])   ? 16'hfffe : 16'h0000;

wire [15:0] ext_nxt  = ir + ext_incr;

// Store source extension word

reg [15:0] inst_sext;

`ifdef CLOCK_GATING

wire       inst_sext_en  = (decode & is_const)                 |

                           (decode & inst_type_nxt[`INST_JMP]) |

                           ((i_state==I_EXT1) & is_sext);

wire       mclk_inst_sext;

omsp_clock_gate clock_gate_inst_sext (.gclk(mclk_inst_sext),

                                      .clk (mclk), .enable(inst_sext_en), .scan_enable(scan_enable));

`else

wire       mclk_inst_sext = mclk;

`endif

always @(posedge mclk_inst_sext or posedge puc_rst)

  if (puc_rst)                                 inst_sext <= 16'h0000;

  else if (decode & is_const)                  inst_sext <= sconst_nxt;

  else if (decode & inst_type_nxt[`INST_JMP])  inst_sext <= {{5{ir[9]}},ir[9:0],1'b0};

`ifdef CLOCK_GATING

  else                                         inst_sext <= ext_nxt;

`else

  else if ((i_state==I_EXT1) & is_sext)        inst_sext <= ext_nxt;

`endif

// Source extension word is ready

wire inst_sext_rdy = (i_state==I_EXT1) & is_sext;

// Store destination extension word

reg [15:0] inst_dext;

`ifdef CLOCK_GATING

wire       inst_dext_en  = ((i_state==I_EXT1) & ~is_sext) |

                            (i_state==I_EXT2);

wire       mclk_inst_dext;

omsp_clock_gate clock_gate_inst_dext (.gclk(mclk_inst_dext),

                                      .clk (mclk), .enable(inst_dext_en), .scan_enable(scan_enable));

`else

wire       mclk_inst_dext = mclk;

`endif

always @(posedge mclk_inst_dext or posedge puc_rst)

  if (puc_rst)                           inst_dext <= 16'h0000;

  else if ((i_state==I_EXT1) & ~is_sext) inst_dext <= ext_nxt;

`ifdef CLOCK_GATING

  else                                   inst_dext <= ext_nxt;

`else

  else if  (i_state==I_EXT2)             inst_dext <= ext_nxt;

`endif

// Destination extension word is ready

wire inst_dext_rdy = (((i_state==I_EXT1) & ~is_sext) | (i_state==I_EXT2));

//=============================================================================

// 6)  DECODE INSTRUCTION

//=============================================================================

`ifdef CLOCK_GATING

wire       mclk_decode;

omsp_clock_gate clock_gate_decode (.gclk(mclk_decode),

                                   .clk (mclk), .enable(decode), .scan_enable(scan_enable));

`else

wire       mclk_decode = mclk;

`endif

//

// 6.1) OPCODE: INSTRUCTION TYPE

//----------------------------------------

// Instructions type is encoded in a one hot fashion as following:

//

// 3'b001: Single-operand arithmetic

// 3'b010: Conditional jump

// 3'b100: Two-operand arithmetic

reg  [2:0] inst_type;

assign     inst_type_nxt = {(ir[15:14]!=2'b00),

                            (ir[15:13]==3'b001),

                            (ir[15:13]==3'b000)} & {3{~irq_detect}};

always @(posedge mclk_decode or posedge puc_rst)

  if (puc_rst)      inst_type <= 3'b000;

`ifdef CLOCK_GATING

  else              inst_type <= inst_type_nxt;

`else

  else if (decode)  inst_type <= inst_type_nxt;

`endif

//

// 6.2) OPCODE: SINGLE-OPERAND ARITHMETIC

//----------------------------------------

// Instructions are encoded in a one hot fashion as following:

//

// 8'b00000001: RRC

// 8'b00000010: SWPB

// 8'b00000100: RRA

// 8'b00001000: SXT

// 8'b00010000: PUSH

// 8'b00100000: CALL

// 8'b01000000: RETI

// 8'b10000000: IRQ

reg   [7:0] inst_so;

wire  [7:0] inst_so_nxt = irq_detect ? 8'h80 : (one_hot8(ir[9:7]) & {8{inst_type_nxt[`INST_SO]}});

always @(posedge mclk_decode or posedge puc_rst)

  if (puc_rst)     inst_so <= 8'h00;

`ifdef CLOCK_GATING

  else             inst_so <= inst_so_nxt;

`else

  else if (decode) inst_so <= inst_so_nxt;

`endif

//

// 6.3) OPCODE: CONDITIONAL JUMP

//--------------------------------

// Instructions are encoded in a one hot fashion as following:

//

// 8'b00000001: JNE/JNZ

// 8'b00000010: JEQ/JZ

// 8'b00000100: JNC/JLO

// 8'b00001000: JC/JHS

// 8'b00010000: JN

// 8'b00100000: JGE

// 8'b01000000: JL

// 8'b10000000: JMP

reg   [2:0] inst_jmp_bin;

always @(posedge mclk_decode or posedge puc_rst)

  if (puc_rst)     inst_jmp_bin <= 3'h0;

`ifdef CLOCK_GATING

  else             inst_jmp_bin <= ir[12:10];

`else

  else if (decode) inst_jmp_bin <= ir[12:10];

`endif

wire [7:0] inst_jmp = one_hot8(inst_jmp_bin) & {8{inst_type[`INST_JMP]}};

//

// 6.4) OPCODE: TWO-OPERAND ARITHMETIC

//-------------------------------------

// Instructions are encoded in a one hot fashion as following:

//

// 12'b000000000001: MOV

// 12'b000000000010: ADD

// 12'b000000000100: ADDC

// 12'b000000001000: SUBC

// 12'b000000010000: SUB

// 12'b000000100000: CMP

// 12'b000001000000: DADD

// 12'b000010000000: BIT

// 12'b000100000000: BIC

// 12'b001000000000: BIS

// 12'b010000000000: XOR

// 12'b100000000000: AND

wire [15:0] inst_to_1hot = one_hot16(ir[15:12]) & {16{inst_type_nxt[`INST_TO]}};

wire [11:0] inst_to_nxt  = inst_to_1hot[15:4];

reg         inst_mov;

always @(posedge mclk_decode or posedge puc_rst)

  if (puc_rst)     inst_mov <= 1'b0;

`ifdef CLOCK_GATING

  else             inst_mov <= inst_to_nxt[`MOV];

`else

  else if (decode) inst_mov <= inst_to_nxt[`MOV];

`endif

//

// 6.5) SOURCE AND DESTINATION REGISTERS

//---------------------------------------

// Destination register

reg [3:0] inst_dest_bin;

always @(posedge mclk_decode or posedge puc_rst)

  if (puc_rst)     inst_dest_bin <= 4'h0;