URL https://opencores.org/ocsvn/openrisc/openrisc/trunk
Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [bootloaders/] [orpmon/] [drivers/] [smc91111.c] - Blame information for rev 707

Go to most recent revision | Details | Compare with Previous | View Log

/*------------------------------------------------------------------------
 . smc91111.c
 . This is a driver for SMSC's 91C111 single-chip Ethernet device.
 .
 . (C) Copyright 2005
 .
 . Copyright (C) 2001 Standard Microsystems Corporation (SMSC)
 .       Developed by Simple Network Magic Corporation (SNMC)
 . Copyright (C) 1996 by Erik Stahlman (ES)
 .
 . This program is free software; you can redistribute it and/or modify
 . it under the terms of the GNU General Public License as published by
 . the Free Software Foundation; either version 2 of the License, or
 . (at your option) any later version.
 .
 . This program is distributed in the hope that it will be useful,
 . but WITHOUT ANY WARRANTY; without even the implied warranty of
 . MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 . GNU General Public License for more details.
 .
 . You should have received a copy of the GNU General Public License
 . along with this program; if not, write to the Free Software
 . Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
 .
 . Information contained in this file was obtained from the LAN91C111
 . manual from SMC.  To get a copy, if you really want one, you can find
 . information under www.smsc.com.
 .
 .
 . author:
 .      Javier Castillo                 ( javier.castillo@urjc.es )
 .
 . Sources:
 .    o   smc91111.c by Erik Stahlman
 .
 . History:
 . 06/05/05  Javier Castillo  Modified smc91111.c to work with OR1200
 ----------------------------------------------------------------------------*/
 
#include "board.h" 
 
#if SMC91111_LAN==1
 
#include "common.h"
#include "smc91111.h"
#include "support.h"
#include "net.h"
 
#ifndef CONFIG_SMC_AUTONEG_TIMEOUT
#define CONFIG_SMC_AUTONEG_TIMEOUT 10
#endif
 
#define ETH_ZLEN 60
#define MEMORY_WAIT_TIME 16
#define SMC_ALLOC_MAX_TRY 5
#define SMC_TX_TIMEOUT 30
#define SWAP16(x)  ((((x) & 0x00ff) << 8) | ( (x) >> 8))
 
 
typedef  unsigned char  byte;
typedef  unsigned short word;
 
//Do nothing but needed to compile
int tx_next;
int rx_next;
 
void (*receive)(volatile unsigned char *add, int len); /* Pointer to function to be called
                                        when frame is received */
 
static void __delay(unsigned long loops)
{
        __asm__ __volatile__ ("1: l.sfeqi %0,0; \
                                l.bnf   1b; \
                                l.addi %0,%0,-1;"
                                : "=r" (loops) : "0" (loops));
}
 
static void udelay(unsigned long usecs)
{
        /* Sigh */
        __delay(usecs);
}
 
static void smc_wait_ms(unsigned int ms){
        udelay(ms*1000);
}
 
static void
print_packet(unsigned long add, int len)
{
  int i;
 
  printf("ipacket: add = %lx len = %d\n", add, len);
  for(i = 0; i < len; i++) {
      if(!(i % 16))
          printf("\n");
      printf(" %.2x", *(((unsigned char *)add) + i));
  }
  printf("\n");
}
 
/*------------------------------------------------------------
 . Reads a register from the MII Management serial interface
 .-------------------------------------------------------------*/
static word smc_read_phy_register(byte phyreg)
{
        int oldBank;
        int i;
        byte mask;
        word mii_reg;
        byte bits[64];
        int clk_idx = 0;
        int input_idx;
        word phydata;
        byte phyaddr=SMC_PHY_ADDR;
 
        // 32 consecutive ones on MDO to establish sync
        for (i = 0; i < 32; ++i)
                bits[clk_idx++] = MII_MDOE | MII_MDO;
 
        // Start code <01>
        bits[clk_idx++] = MII_MDOE;
        bits[clk_idx++] = MII_MDOE | MII_MDO;
 
        // Read command <10>
        bits[clk_idx++] = MII_MDOE | MII_MDO;
        bits[clk_idx++] = MII_MDOE;
 
        // Output the PHY address, msb first
        mask = (byte)0x10;
        for (i = 0; i < 5; ++i)
                {
                if (phyaddr & mask)
                        bits[clk_idx++] = MII_MDOE | MII_MDO;
                else
                        bits[clk_idx++] = MII_MDOE;
 
                // Shift to next lowest bit
                mask >>= 1;
                }
 
        // Output the phy register number, msb first
        mask = (byte)0x10;
        for (i = 0; i < 5; ++i)
                {
                if (phyreg & mask)
                        bits[clk_idx++] = MII_MDOE | MII_MDO;
                else
                        bits[clk_idx++] = MII_MDOE;
 
                // Shift to next lowest bit
                mask >>= 1;
                }
 
        // Tristate and turnaround (2 bit times)
        bits[clk_idx++] = 0;
        //bits[clk_idx++] = 0;
 
        // Input starts at this bit time
        input_idx = clk_idx;
 
        // Will input 16 bits
        for (i = 0; i < 16; ++i)
                bits[clk_idx++] = 0;
 
        // Final clock bit
        bits[clk_idx++] = 0;
 
        // Save the current bank
        oldBank = REG16(ETH_BASE+BANK_SELECT);
 
        // Select bank 3
        SMC_SELECT_BANK( 3 );
 
        // Get the current MII register value
        mii_reg = REG16(ETH_BASE+MII_REG);
 
        // Turn off all MII Interface bits
        mii_reg &= ~(MII_MDOE|MII_MCLK|MII_MDI|MII_MDO);
 
        // Clock all 64 cycles
        for (i = 0; i < sizeof bits; ++i)
                {
                // Clock Low - output data
                REG16(ETH_BASE+MII_REG)= mii_reg | bits[i];
                udelay(500);
 
 
                // Clock Hi - input data
                REG16(ETH_BASE+MII_REG)= mii_reg | bits[i] | MII_MCLK;
                udelay(500);
                bits[i] |= REG16(ETH_BASE+MII_REG) & MII_MDI;
                }
 
        // Return to idle state
        // Set clock to low, data to low, and output tristated
        REG16(ETH_BASE+MII_REG)=mii_reg;
        udelay(500);
 
        // Restore original bank select
        SMC_SELECT_BANK( oldBank );
 
        // Recover input data
        phydata = 0;
        for (i = 0; i < 16; ++i)
                {
                phydata <<= 1;
 
                if (bits[input_idx++] & MII_MDI)
                        phydata |= 0x0001;
                }
 
        return(phydata);
}
 
static void smc_write_phy_register(byte phyreg, word phydata){
 
        int oldBank;
        int i;
        word mask;
        word mii_reg;
        byte bits[65];
        int clk_idx=0;
        byte phyaddr=SMC_PHY_ADDR;
 
        /*32 consecutives ones on MDO to establish sync*/
        for(i=0; i<32;i++)
                bits[clk_idx++]=MII_MDOE | MII_MDO;
 
        // Start code <01>
        bits[clk_idx++] = MII_MDOE;
        bits[clk_idx++] = MII_MDOE | MII_MDO;
 
        // Write command <01>
        bits[clk_idx++] = MII_MDOE;
        bits[clk_idx++] = MII_MDOE | MII_MDO;
 
        // Output the PHY address, msb first
        mask = (byte)0x10;
        for (i = 0; i < 5; ++i)
                {
                if (phyaddr & mask)
                        bits[clk_idx++] = MII_MDOE | MII_MDO;
                else
                        bits[clk_idx++] = MII_MDOE;
 
                // Shift to next lowest bit
                mask >>= 1;
                }
 
        // Output the phy register number, msb first
        mask = (byte)0x10;
        for (i = 0; i < 5; ++i)
                {
                if (phyreg & mask)
                        bits[clk_idx++] = MII_MDOE | MII_MDO;
                else
                        bits[clk_idx++] = MII_MDOE;
 
                // Shift to next lowest bit
                mask >>= 1;
                }
 
        // Tristate and turnaround (2 bit times)
        bits[clk_idx++] = 0;
        bits[clk_idx++] = 0;
 
        // Write out 16 bits of data, msb first
        mask = 0x8000;
        for (i = 0; i < 16; ++i)
                {
                if (phydata & mask)
                        bits[clk_idx++] = MII_MDOE | MII_MDO;
                else
                        bits[clk_idx++] = MII_MDOE;
 
                // Shift to next lowest bit
                mask >>= 1;
                }
 
        // Final clock bit (tristate)
        bits[clk_idx++] = 0;
 
        // Save the current bank
        oldBank = REG16(ETH_BASE+BANK_SELECT);
 
        // Select bank 3
        SMC_SELECT_BANK( 3 );
 
        // Get the current MII register value
        mii_reg = REG16(ETH_BASE+MII_REG);
 
        // Turn off all MII Interface bits
        mii_reg &= ~(MII_MDOE|MII_MCLK|MII_MDI|MII_MDO);
 
        // Clock all cycles
        for (i = 0; i < sizeof bits; ++i)
                {
                // Clock Low - output data
                REG16(ETH_BASE+MII_REG)= mii_reg | bits[i];
                udelay(50);
 
 
                // Clock Hi - input data
                REG16(ETH_BASE+MII_REG)= mii_reg | bits[i] | MII_MCLK;
                udelay(50);
                bits[i] |= REG16(ETH_BASE+MII_REG) & MII_MDI;
                }
 
        // Return to idle state
        // Set clock to low, data to low, and output tristated
        REG16(ETH_BASE+MII_REG)=mii_reg;
        udelay(50);
 
        // Restore original bank select
        SMC_SELECT_BANK( oldBank );
 
}
 
 
static void smc_phy_configure (void){
        int timeout;
        byte phyaddr;
        word my_phy_caps;       /* My PHY capabilities */
        word my_ad_caps;        /* My Advertised capabilities */
        word status = 0; /*;my status = 0 */
        int failed = 0;
 
        /* Get the detected phy address */
        phyaddr = SMC_PHY_ADDR;
 
        /* Reset the PHY, setting all other bits to zero */
        smc_write_phy_register (PHY_CNTL_REG, PHY_CNTL_RST);
 
        /* Wait for the reset to complete, or time out */
        timeout = 6;            /* Wait up to 3 seconds */
        while (timeout--) {
                if (!(smc_read_phy_register (PHY_CNTL_REG)
                      & PHY_CNTL_RST)) {
                        /* reset complete */
                        break;
                }
 
                smc_wait_ms (500);      /* wait 500 millisecs */
        }
 
        if (timeout < 1) {
                printf ("PHY reset timed out\n");
                goto smc_phy_configure_exit;
        }
 
        /* Read PHY Register 18, Status Output */
        /* lp->lastPhy18 = smc_read_phy_register(PHY_INT_REG); */
 
        /* Enable PHY Interrupts (for register 18) */
        /* Interrupts listed here are disabled */
        smc_write_phy_register (PHY_MASK_REG, 0xffff);
 
        /* Configure the Receive/Phy Control register */
        SMC_SELECT_BANK (0);
        REG16(ETH_BASE+RPC_REG)=RPC_DEFAULT;
 
        /* Copy our capabilities from PHY_STAT_REG to PHY_AD_REG */
        my_phy_caps = smc_read_phy_register (PHY_STAT_REG);
        my_ad_caps = PHY_AD_CSMA;       /* I am CSMA capable */
 
        if (my_phy_caps & PHY_STAT_CAP_T4)
                my_ad_caps |= PHY_AD_T4;
 
        if (my_phy_caps & PHY_STAT_CAP_TXF)
                my_ad_caps |= PHY_AD_TX_FDX;
 
        if (my_phy_caps & PHY_STAT_CAP_TXH)
                my_ad_caps |= PHY_AD_TX_HDX;
 
        if (my_phy_caps & PHY_STAT_CAP_TF)
                my_ad_caps |= PHY_AD_10_FDX;
 
        if (my_phy_caps & PHY_STAT_CAP_TH)
                my_ad_caps |= PHY_AD_10_HDX;
 
        /* Update our Auto-Neg Advertisement Register */
        smc_write_phy_register (PHY_AD_REG, my_ad_caps);
 
        /* Read the register back.  Without this, it appears that when */
        /* auto-negotiation is restarted, sometimes it isn't ready and */
        /* the link does not come up. */
        smc_read_phy_register(PHY_AD_REG);
 
        /* Restart auto-negotiation process in order to advertise my caps */
        smc_write_phy_register (PHY_CNTL_REG,
                                PHY_CNTL_ANEG_EN | PHY_CNTL_ANEG_RST);
 
        /* Wait for the auto-negotiation to complete.  This may take from */
        /* 2 to 3 seconds. */
        /* Wait for the reset to complete, or time out */
        timeout = CONFIG_SMC_AUTONEG_TIMEOUT * 2;
        while (timeout--) {
 
                status = smc_read_phy_register (PHY_STAT_REG);
                if (status & PHY_STAT_ANEG_ACK) {
                        /* auto-negotiate complete */
                        break;
                }
 
                smc_wait_ms (500);      /* wait 500 millisecs */
 
                /* Restart auto-negotiation if remote fault */
                if (status & PHY_STAT_REM_FLT) {
                        printf ("PHY remote fault detected\n");
 
                        /* Restart auto-negotiation */
                        printf ("PHY restarting auto-negotiation\n");
                        smc_write_phy_register (PHY_CNTL_REG,
                                                PHY_CNTL_ANEG_EN |
                                                PHY_CNTL_ANEG_RST |
                                                PHY_CNTL_SPEED |
                                                PHY_CNTL_DPLX);
                }
        }
 
        if (timeout < 1) {
                printf ("PHY auto-negotiate timed out\n");
                failed = 1;
        }
 
        /* Fail if we detected an auto-negotiate remote fault */
        if (status & PHY_STAT_REM_FLT) {
                printf ("PHY remote fault detected\n");
                failed = 1;
        }
 
        /* Re-Configure the Receive/Phy Control register */
        REG16(ETH_BASE+RPC_REG)=RPC_DEFAULT;
 
smc_phy_configure_exit: ;
 
}
 
static inline void smc_wait_mmu_release_complete (void)
{
        int count = 0;
 
        /* assume bank 2 selected */
        while (REG16(ETH_BASE+MMU_CMD_REG) & MC_BUSY) {
                udelay (1);     /* Wait until not busy */
                if (++count > 200)
                        break;
        }
}
 
static void eth_reset(){
 
        /* This resets the registers mostly to defaults, but doesn't
           affect EEPROM.  That seems unnecessary */
        SMC_SELECT_BANK (0);
        REG16(ETH_BASE+RCR_REG)=RCR_SOFTRST;
 
        /* Setup the Configuration Register */
        /* This is necessary because the CONFIG_REG is not affected */
        /* by a soft reset */
 
        SMC_SELECT_BANK (1);
        REG16(ETH_BASE+CONFIG_REG)=CONFIG_DEFAULT;
 
        /* Release from possible power-down state */
        /* Configuration register is not affected by Soft Reset */
        REG16(ETH_BASE+CONFIG_REG)=REG16(ETH_BASE+CONFIG_REG) | CONFIG_EPH_POWER_EN;
 
        SMC_SELECT_BANK (0);
 
        /* this should pause enough for the chip to be happy */
        udelay (100);
 
        /* Disable transmit and receive functionality */
        REG16(ETH_BASE+RCR_REG)=RCR_CLEAR;
        REG16(ETH_BASE+TCR_REG)=TCR_CLEAR;
 
        /* set the control register */
        SMC_SELECT_BANK (1);
        REG16(ETH_BASE+CTL_REG)=CTL_DEFAULT;
 
        /* Reset the MMU */
        SMC_SELECT_BANK (2);
        smc_wait_mmu_release_complete ();
        REG16(ETH_BASE+MMU_CMD_REG)=MC_RESET;
        while (REG16(ETH_BASE+MMU_CMD_REG) & MC_BUSY)
                udelay (1);     /* Wait until not busy */
 
        /* Note:  It doesn't seem that waiting for the MMU busy is needed here,
           but this is a place where future chipsets _COULD_ break.  Be wary
           of issuing another MMU command right after this */
 
        /* Disable all interrupts */
        REG8(ETH_BASE+IM_REG)=0;
}
 
void eth_init (void (*rec)(volatile unsigned char *, int)){
 
        receive = rec;
 
        /*First make a SW reset of the chip*/
        eth_reset();
 
        /*Enable TX and Rx*/
        SMC_SELECT_BANK(0x0);
        REG16(ETH_BASE+TCR_REG)=TCR_DEFAULT;
        REG16(ETH_BASE+RCR_REG)=RCR_DEFAULT;
        REG16(ETH_BASE+RPC_REG)=RPC_DEFAULT;
 
        /*Configure PHY with autoneg*/
        smc_phy_configure();
 
        /*Set MAC address*/
        SMC_SELECT_BANK(0x1);
        REG8(ETH_BASE+ADDR0_REG)=ETH_MACADDR0;
        REG8(ETH_BASE+ADDR0_REG+1)=ETH_MACADDR1;
        REG8(ETH_BASE+ADDR0_REG+2)=ETH_MACADDR2;
        REG8(ETH_BASE+ADDR0_REG+3)=ETH_MACADDR3;
        REG8(ETH_BASE+ADDR0_REG+4)=ETH_MACADDR4;
        REG8(ETH_BASE+ADDR0_REG+5)=ETH_MACADDR5;
 
}
 
void eth_halt(void) {
        /* no more interrupts for me */
        SMC_SELECT_BANK( 2 );
        REG8(ETH_BASE+IM_REG)=0;
 
        /* and tell the card to stay away from that nasty outside world */
        SMC_SELECT_BANK( 0 );
        REG8(ETH_BASE+RCR_REG)=RCR_CLEAR;
        REG8(ETH_BASE+TCR_REG)=TCR_CLEAR;
}
 
unsigned long eth_rx (void){
 
        int     packet_number;
        word    status;
        word    packet_length;
        word    packet_length_loop;
        int     is_error = 0;
        byte saved_pnr;
        word saved_ptr;
        word word_readed;
        byte *data;
 
        SMC_SELECT_BANK(2);
        /* save PTR and PTR registers */
        saved_pnr = REG8(ETH_BASE+PN_REG );
        saved_ptr = REG16(ETH_BASE+PTR_REG );
 
        packet_number = REG16(ETH_BASE+RXFIFO_REG );
 
        if ( packet_number & RXFIFO_REMPTY ) {
                return 0;
        }
 
        /*  start reading from the start of the packet */
        REG16(ETH_BASE+PTR_REG)=PTR_READ | PTR_RCV | PTR_AUTOINC;
 
        /* First two words are status and packet_length */
        status          = REG16(ETH_BASE+SMC91111_DATA_REG );
        packet_length   = REG16(ETH_BASE+SMC91111_DATA_REG );
 
        packet_length &= 0x07ff;  /* mask off top bits */
 
        #ifdef DEBUG
        printf("RCV: STATUS %4x LENGTH %4x\n", status, packet_length );
        #endif
        if ( !(status & RS_ERRORS ) ){
                /* Adjust for having already read the first two words */
                packet_length -= 4; /*4; */
 
                /* set odd length for bug in LAN91C111, */
                /* which never sets RS_ODDFRAME */
                /* TODO ? */
                #ifdef DEBUG
                printf(" Reading %d words and %d byte(s) \n",(packet_length >> 1 ), packet_length & 1 );
                #endif
                packet_length_loop=packet_length>>1;
 
                data=(byte*)NetRxPackets[0];
                while(packet_length_loop-->0){
                  word_readed=REG16(ETH_BASE+SMC91111_DATA_REG);
                  *((word*)data)=SWAP16(word_readed);
                  data+=sizeof(word);
                }
 
        } else {
                /* error ... */
                /* TODO ? */
                is_error = 1;
        }
 
        while ( REG16(ETH_BASE+MMU_CMD_REG) & MC_BUSY )
                udelay(1); /* Wait until not busy */
 
        /*  error or good, tell the card to get rid of this packet */
        REG16(ETH_BASE+MMU_CMD_REG)=MC_RELEASE;
 
        while ( REG16(ETH_BASE+MMU_CMD_REG) & MC_BUSY )
                udelay(1); /* Wait until not busy */
 
        /* restore saved registers */
 
        REG8(ETH_BASE+PN_REG)=saved_pnr;
 
        REG16(ETH_BASE+PTR_REG)=saved_ptr;
 
        if (!is_error) {
                /* Pass the packet up to the protocol layers. */
                receive(NetRxPackets[0], packet_length);
                return packet_length;
        } else {
                return 0;
        }
}
 
#define CFG_HZ 1000
static int poll4int (byte mask, int timeout)
{
        int tmo = get_timer (0) + timeout * CFG_HZ;
        int is_timeout = 0;
        word old_bank = REG16(ETH_BASE+BSR_REG);
        #ifdef DEBUG
        printf ("Polling...\n");
        #endif
        SMC_SELECT_BANK (2);
        while ((REG16(ETH_BASE+SMC91111_INT_REG) & mask) == 0) {
                if (get_timer (0) >= tmo) {
                        is_timeout = 1;
                        break;
                }
        }
 
        /* restore old bank selection */
        SMC_SELECT_BANK (old_bank);
 
        if (is_timeout)
                return 1;
        else
                return 0;
}
 
void eth_send(void *buf, unsigned long len) {
 
        byte packet_no;
        byte *bufb;
        int length;
        int lengtht;
        int numPages;
        int try = 0;
        int time_out;
        byte status;
        byte saved_pnr;
        word saved_ptr;
 
        /* save PTR and PNR registers before manipulation */
        SMC_SELECT_BANK (2);
        saved_pnr = REG8( ETH_BASE+PN_REG );
        saved_ptr = REG16( ETH_BASE+PTR_REG );
        #ifdef DEBUG
        printf ("smc_hardware_send_packet\n");
        #endif
        length = ETH_ZLEN < len ? len : ETH_ZLEN;
 
        /* allocate memory
         ** The MMU wants the number of pages to be the number of 256 bytes
         ** 'pages', minus 1 ( since a packet can't ever have 0 pages :) )
         **
         ** The 91C111 ignores the size bits, but the code is left intact
         ** for backwards and future compatibility.
         **
         ** Pkt size for allocating is data length +6 (for additional status
         ** words, length and ctl!)
         **
         ** If odd size then last byte is included in this header.
         */
        numPages = ((length & 0xfffe) + 6);
        numPages >>= 8;         /* Divide by 256 */
 
        if (numPages > 7) {
                printf ("Far too big packet error. \n");
                return;
        }
 
        /* now, try to allocate the memory */
        SMC_SELECT_BANK (2);
        REG16( ETH_BASE+MMU_CMD_REG)=MC_ALLOC | numPages;
 
        /* FIXME: the ALLOC_INT bit never gets set *
         * so the following will always give a     *
         * memory allocation error.                *
         * same code works in armboot though       *
         * -ro
         */
 
again:
        try++;
        time_out = MEMORY_WAIT_TIME;
        do {
                status = REG8( ETH_BASE+SMC91111_INT_REG);
                if (status & IM_ALLOC_INT) {
                        /* acknowledge the interrupt */
                        REG8( ETH_BASE+SMC91111_INT_REG)=IM_ALLOC_INT;
                        break;
                }
        } while (--time_out);
 
        if (!time_out) {
                if (try < SMC_ALLOC_MAX_TRY)
                        goto again;
                else
                        return;
        }
 
        /* I can send the packet now.. */
 
        bufb = (byte *) buf;
 
        /* If I get here, I _know_ there is a packet slot waiting for me */
        packet_no = REG8( ETH_BASE+AR_REG);
        if (packet_no & AR_FAILED) {
                /* or isn't there?  BAD CHIP! */
                printf ("Memory allocation failed. \n");
                return;
        }
 
        /* we have a packet address, so tell the card to use it */
        REG8( ETH_BASE+PN_REG)=packet_no;
        /* do not write new ptr value if Write data fifo not empty */
        while ( saved_ptr & PTR_NOTEMPTY )
                printf ("Write data fifo not empty!\n");
 
        /* point to the beginning of the packet */
        REG16( ETH_BASE+PTR_REG)=PTR_AUTOINC;
 
 
        /* send the packet length ( +6 for status, length and ctl byte )
           and the status word ( set to zeros ) */
        REG16(ETH_BASE+SMC91111_DATA_REG)=0;
        /* send the packet length ( +6 for status words, length, and ctl */
        REG16(ETH_BASE+SMC91111_DATA_REG)=length + 6;
 
 
        /* send the actual data */
        lengtht=length>>1;
        while(lengtht-->0){
          REG16(ETH_BASE+SMC91111_DATA_REG)=SWAP16(*((word*)bufb));
          bufb+=sizeof(word);
        }
 
 
        /* Send the last byte, if there is one.   */
        if ((length & 1) == 0) {
                REG16(ETH_BASE+SMC91111_DATA_REG)=0;
        } else {
                REG16(ETH_BASE+SMC91111_DATA_REG)=bufb[length - 1] | 0x2000;
        }
 
        /* and let the chipset deal with it */
        REG16(ETH_BASE+MMU_CMD_REG)=MC_ENQUEUE;
 
        /* poll for TX INT */
        /* if (poll4int (IM_TX_INT, SMC_TX_TIMEOUT)) { */
        /* poll for TX_EMPTY INT - autorelease enabled */
        if (poll4int(IM_TX_EMPTY_INT, SMC_TX_TIMEOUT)) {
                /* sending failed */
                printf ("TX timeout, sending failed...\n");
 
                /* release packet */
                /* no need to release, MMU does that now */
 
                /* wait for MMU getting ready (low) */
                while (REG16(ETH_BASE+MMU_CMD_REG) & MC_BUSY) {
                        udelay (10);
                }
 
                printf ("MMU ready\n");
 
 
                return;
        } else {
                /* ack. int */
                REG8(ETH_BASE+SMC91111_INT_REG)=IM_TX_EMPTY_INT;
                /* SMC_outb (IM_TX_INT, SMC91111_INT_REG); */
                #ifdef DEBUG
                printf ("Sent packet of length %u\n",length);
                #endif
 
                /* release packet */
                /* no need to release, MMU does that now */
 
                /* wait for MMU getting ready (low) */
                while (REG16(ETH_BASE+MMU_CMD_REG) & MC_BUSY) {
                        udelay (10);
                }
 
        }
 
        /* restore previously saved registers */
        REG8(ETH_BASE+PN_REG)=saved_pnr;
        REG16(ETH_BASE+PTR_REG)=saved_ptr, PTR_REG;
 
        return;
 
}
 
#endif
Browse

Tools

Subversion Repositories openrisc

[/] [openrisc/] [trunk/] [bootloaders/] [orpmon/] [drivers/] [smc91111.c] - Blame information for rev 707

Line No.	Rev	Author	Line
1	2	marcus.erl	`/*------------------------------------------------------------------------`
2			`. smc91111.c`
3			`. This is a driver for SMSC's 91C111 single-chip Ethernet device.`
4			`.`
5			`. (C) Copyright 2005`
6			`.`
7			`. Copyright (C) 2001 Standard Microsystems Corporation (SMSC)`
8			`. Developed by Simple Network Magic Corporation (SNMC)`
9			`. Copyright (C) 1996 by Erik Stahlman (ES)`
10			`.`
11			`. This program is free software; you can redistribute it and/or modify`
12			`. it under the terms of the GNU General Public License as published by`
13			`. the Free Software Foundation; either version 2 of the License, or`
14			`. (at your option) any later version.`
15			`.`
16			`. This program is distributed in the hope that it will be useful,`
17			`. but WITHOUT ANY WARRANTY; without even the implied warranty of`
18			`. MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the`
19			`. GNU General Public License for more details.`
20			`.`
21			`. You should have received a copy of the GNU General Public License`
22			`. along with this program; if not, write to the Free Software`
23			`. Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA`
24			`.`
25			`. Information contained in this file was obtained from the LAN91C111`
26			`. manual from SMC. To get a copy, if you really want one, you can find`
27			`. information under www.smsc.com.`
28			`.`
29			`.`
30			`. author:`
31			`. Javier Castillo ( javier.castillo@urjc.es )`
32			`.`
33			`. Sources:`
34			`. o smc91111.c by Erik Stahlman`
35			`.`
36			`. History:`
37			`. 06/05/05 Javier Castillo Modified smc91111.c to work with OR1200`
38			`----------------------------------------------------------------------------*/`
39
40			`#include "board.h"`